Transformer oil

Transformer oil or insulating oil is usually a highly-refined mineral oil that is stable at high temperatures and has excellent at electrical insulating properties. It is used in oil-filled transformers, some types of high voltage capacitors, fluorescent lamp ballasts, and some types of high voltage switches and circuit breakers. Its functions are to insulate, suppress corona and arcing, and to serve as a coolant.

Explanation

The oil helps cool the transformer. Because it also provides part of the electrical insulation between internal live parts, transformer oil must remain stable at high temperatures for an extended period. To improve cooling of large power transformers, the oil-filled tank may have external radiators through which the oil circulates by natural convection. Very large or high-power transformers (with capacities of thousands of KVA) may also have cooling fans, oil pumps, and even oil-to-water heat exchangers.

Large, high voltage transformers undergo prolonged drying processes, using electrical self-heating, the application of a vacuum, or both to ensure that the transformer is completely free of water vapor before the cooling oil is introduced. This helps prevent corona formation and subsequent electrical breakdown under load.

Oil filled transformers with a conservator (an oil tank above the transformer) tend to be equipped with Buchholz relays. These are safety devices that detect the build up of gases (such as acetylene) inside the transformer (a side effect of corona or an electric arc in the windings) and switch off the transformer. Transformers without conservators are usually equipped with sudden pressure relays, which perform a similar function as the Buchholz relay.

The flash point (min) and pour point (max) are 140 °C and −6 °C respectively. The dielectric strength of new untreated oil is 12 MV/m (RMS) and after treatment it should be >24 MV/m (RMS).

Oil transformer

Large transformers for indoor use must either be of the dry type, that is, containing no liquid, or use a less-flammable liquid.

Well into the 1970s, polychlorinated biphenyls (PCB)s were often used as a dielectric fluid since they are not flammable. They are toxic, and under incomplete combustion, can form highly toxic products such as furan. Starting in the early 1970s, concerns about the toxicity of PCBs have led to their banning in many countries.

Today, non-toxic, stable silicon-based or fluorinated hydrocarbons are used, where the added expense of a fire-resistant liquid offsets additional building cost for a transformer vault. Combustion-resistant vegetable oil-based dielectric coolants and synthetic pentaerythritol tetra fatty acid (C7, C8) esters are also becoming increasingly common as alternatives to naphthenic mineral oil. Esters are non-toxic to aquatic life, readily biodegradable, and have a lower volatility and a higher flash points than mineral oil.

Transformer Oil Testing

Transformer Oils are subject to from electrical and mechanical stresses while a transformer is in operation. In addition there are contaminations caused due to chemical interactions with windings and other solid insulations, catalyzed by high operating temperature. As a result the original chemical properties of Transformer Oil changes gradually, rendering it ineffective for its intended purpose after many years. Hence this oil has to be periodically tested to ascertain its basic electrical properties, and make sure it is suitable for further use or necessary actions like filtration/regeneration has to be done These tests can be divided into 1. General Electrical & Physical tests

- Color & Appearance
- Breakdown Voltage
- Water Content
- Acidity (Neutralization Value)
- Dielectric Dissipation Factor
- Resistivity
- Sediments & Sludge
- Interfacial Tension
- Flash Point
- Pour Point
- Density
- Kinematic Viscosity

2. Dissolved Gas Analysis 3. Furan Analysis 4. PCB Analysis The details of conducting these tests is available in standards released by IEC, ASTM, IS, BS, and testing can be done by either of the methods. The Furan and DGA tests are specifically not for determining the quality of Transformer Oil, but for determining any abnormalities in the internal windings of the transformer or the paper insulation of the transformer, which cannot be otherwise detected without a complete overhaul of the transformer. Suggested intervals for these test are General and Physical tests - bi-yearly Dissolved Gas Analysis - yearly Furan testing - once every 2 years, subject to the transformer being in operation for min 5 years

External Link

• http://www.dissolvedgasanalysis.in
• http://oil-testers.com

References

• Less and nonflammable liquid-insulated transformers, approval standard class Number 3990, Factory Mutual Research Corporation, 1997.

• McShane C.P. (2001) Relative properties of the new combustion-resistant vegetable oil-based dielectric coolants for distribution and power transformers. IEEE Trans. on Industry Applications, Vol.37, No.4, July/August 2001, pp.1132-1139, No. 0093-9994/01, 2001 IEEE.

• “The Environmental technology verification program”, U.S. Environmental Protection Agency, Washington, DC, VS-R-02-02, June 2002. [1]

• IEEE Guide for loading mineral-oil-immersed transformers, IEEE Standard C57.91-1995, 1996.

• Transformer Oil Testing.

• Transformer Maintenance.

• Patent for a high temperature transformer