Turning
This article needs additional citations for verification. (January 2010) |
![](http://upload.wikimedia.org/wikipedia/commons/thumb/e/ed/SchruppenDrehen.jpg/220px-SchruppenDrehen.jpg)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/5/58/StechenDrehen.jpg/220px-StechenDrehen.jpg)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/9/90/SchlichtenDrehen.jpg/220px-SchlichtenDrehen.jpg)
Turning is a machining process in which a cutting tool, typically a non-rotary tool bit, describes a helix toolpath by moving more or less linearly while the workpiece rotates. The tool's axes of movement may be literally a straight line, or they may be along some set of curves or angles, but they are essentially linear (in the non mathematical sense). Usually the term "turning" is reserved for the generation of external surfaces by this cutting action, whereas this same essential cutting action when applied to internal surfaces (that is, holes, of one kind or another) is called "boring". Thus the phrase "turning and boring" categorizes the larger family of (essentially similar) processes known as lathing. The cutting of faces on the workpiece (that is, surfaces perpendicular to its rotating axis), whether with a turning or boring tool, is called "facing", and may be lumped into either category as a subset.
Turning can be done manually, in a traditional form of lathe, which frequently requires continuous supervision by the operator, or by using an automated lathe which does not. Today the most common type of such automation is computer numerical control, better known as CNC. (CNC is also commonly used with many other types of machining besides turning.)
When turning, a piece of relatively rigid material (such as wood, metal, plastic, or stone) is rotated and a cutting tool is traversed along 1, 2, or 3 axes of motion to produce precise diameters and depths. Turning can be either on the outside of the cylinder or on the inside (also known as boring) to produce tubular components to various geometries. Although now quite rare, early lathes could even be used to produce complex geometric figures, even the platonic solids; although since the advent of CNC it has become unusual to use non-computerized toolpath control for this purpose.
The turning processes are typically carried out on a lathe, considered to be the oldest machine tools, and can be of four different types such as straight turning, taper turning, profiling or external grooving. Those types of turning processes can produce various shapes of materials such as straight, conical, curved, or grooved workpiece. In general, turning uses simple single-point cutting tools. Each group of workpiece materials has an optimum set of tools angles which have been developed through the years.
The bits of waste metal from turning operations are known as chips (North America), or swarf (Britain). In some areas they may be known as turnings.
Turning operations
Turning specific operations include:
- Turning
![](http://upload.wikimedia.org/wikipedia/commons/thumb/1/1e/L%C3%A4ngs-Rund-Drehen.jpg/100px-L%C3%A4ngs-Rund-Drehen.jpg)
This operation is one of the most basic machining processes. That is, the part is rotated while a single point cutting tool is moved parallel to the axis of rotation.[1] Turning can be done on the external surface of the part as well as internally (boring). The starting material is generally a workpiece generated by other processes such as casting, forging, extrusion, or drawing.
- Tapered turning
- a) from the compound slide b) from taper turning attachment c) using a hydraulic copy attachment d) using a C.N.C. lathe e) using a form tool f) by the offsetting of the tailstock - this method more suited for shallow tapers.[2]
- Spherical generation
- The proper expression for making or turning a shape is to generate as in to generate a form around a fixed axis of revolution. a) using hydraulic copy attachment b) C.N.C. (computerised numerically controlled) lathe c) using a form tool (a rough and ready method) d) using bed jig (need drawing to explain).[2]
- Hard turning
- Hard turning is a turning done on materials with a Rockwell C hardness greater than 45. It is typically performed after the workpiece is heat treated.[3]
- The process is intended to replace or limit traditional grinding operations. Hard turning, when applied for purely stock removal purposes, competes favorably with rough grinding. However, when it is applied for finishing where form and dimension are critical, grinding is superior. Grinding produces higher dimensional accuracy of roundness and cylindricity. In addition, polished surface finishes of Rz=0.3-0.8z cannot be achieved with hard turning alone. Hard turning is appropriate for parts requiring roundness accuracy of 0.5-12 micrometres, and/or surface roughness of Rz 0.8–7.0 micrometres. It is used for gears, injection pump components, hydraulic components, among other applications.[3]
- Facing
![](http://upload.wikimedia.org/wikipedia/commons/thumb/7/78/Quer-Plan-Drehen.jpg/100px-Quer-Plan-Drehen.jpg)
Facing in the context of turning work involves moving the cutting tool at right angles to the axis of rotation of the rotating workpiece.[1] This can be performed by the operation of the cross-slide, if one is fitted, as distinct from the longitudinal feed (turning). It is frequently the first operation performed in the production of the workpiece, and often the last—hence the phrase "ending up".
- Parting
This process, also called parting off or cutoff, is used to create deep grooves which will remove a completed or part-complete component from its parent stock.
- Grooving
![](http://upload.wikimedia.org/wikipedia/commons/thumb/b/bf/Quer-Rund-Drehen.jpg/100px-Quer-Rund-Drehen.jpg)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/5/5e/L%C3%A4ngs-Plan-Drehen.jpg/100px-L%C3%A4ngs-Plan-Drehen.jpg)
Grooving is like parting, except that grooves are cut to a specific depth instead of severing a completed/part-complete component from the stock. Grooving can be performed on internal and external surfaces, as well as on the face of the part (face grooving or trepanning).
Non-specific operations include:
- Boring
- Enlarging or smoothing an existing hole created by drilling, moulding etc.i.e. the machining of internal cylindrical forms (generating) a) by mounting workpiece to the spindle via a chuck or faceplate b) by mounting workpiece onto the cross slide and placing cutting tool into the chuck. This work is suitable for castings that are too awkward to mount in the face plate. On long bed lathes large workpiece can be bolted to a fixture on the bed and a shaft passed between two lugs on the workpiece and these lugs can be bored out to size. A limited application but one that is available to the skilled turner/machinist.[2]
- Drilling
- is used to remove material from the inside of a workpiece. This process utilizes standard drill bits held stationary in the tail stock or tool turret of the lathe. The process can be done by separately available drilling machines.
![](http://upload.wikimedia.org/wikipedia/commons/thumb/1/17/R%C3%A4ndelwerkzeug.jpg/100px-R%C3%A4ndelwerkzeug.jpg)
- Knurling
- The cutting of a serrated pattern onto the surface of a part to use as a hand grip using a special purpose knurling tool.[2]
- Reaming
- The sizing operation that removes a small amount of metal from a hole already drilled.[2] It is done for making internal holes of very accurate diameters. For example, a 6mm hole is made by drilling with 5.98 mm drill bit and then reamed to accurate dimensions.
- Threading
- Both standard and non-standard screw threads can be turned on a lathe using an appropriate cutting tool. (Usually having a 60, or 55° nose angle) Either externally, or within a bore.[4] Generally referred to as single-point threading.
- tapping of threaded nuts and holes a) using hand taps and tailstock centre b)using a tapping device with a slipping clutch to reduce risk of breakage of the tap.[2]
- threading operations include a)all types of external and internal thread forms using a single point tool also taper threads, double start threads, multi start threads, worms as used in worm wheel reduction boxes, leadscrew with single or multistart threads. b) by the use of threading boxes fitted with 4 form tools, up to 2" diameter threads but it is possible to find larger boxes than this.[2]
- Polygonal turning
- in which non-circular forms are machined without interrupting the rotation of the raw material.
Lathes
A lathe is a machine tool used principally for shaping pieces of metal, wood, or other materials by causing the workpiece to be held and rotated by the lathe while a tool bit is advanced into the work causing the cutting action. Lathes can be divided into three types for easy identification: engine lathe, turret lathe, and special purpose lathes. Some smaller ones are bench mounted and semi-portable. The larger lathes are floor mounted and may require special transportation if they must be moved. Field and maintenance shops generally use a lathe that can be adapted to many operations and that is not too large to be moved from one work site to another. The engine lathe is ideally suited for this purpose. A trained operator can accomplish more machining jobs with the engine lathe than with any other machine tool. Turret lathes and special purpose lathes are usually used in production or job shops for mass production or specialized parts, while basic engine lathes are usually used for any type of lathe work.
Workholding methods
![](http://upload.wikimedia.org/wikipedia/commons/thumb/d/d0/HardingeR8Collets.jpg/100px-HardingeR8Collets.jpg)
- Chuck: Chucks are a very common workholding method. There are many types, some for round and square stock, and other for irregular shapes.
- Collet: Primarily used for small round workpieces.
- Faceplate: A faceplate, drive dog, and mandrel may be used to turn workpieces such as gear blanks.
- Centers: Pointed cones between which the part spins, often driven by a 'dog'. May be used to turn longer shafts and cylinders.
- Drive center: Use hydraulic or spring-loaded teeth that "bite" into the end of workpieces and can be used when the entire length of the workpiece must be machined.
Tooling
The various angles, shapes, and sizes of a single-point cutting tool have direct relation to the resulting surface of a workpiece in machining operations. Different types of angle such as rake angle, side rake angle, cutting-edge angle, relief angle, nose radius exist and may be different with respect to the workpiece. Also, there are many shapes of single-point cutting tools, such as V-shaped and Square. Usually, a special toolholder is used to hold the cutting tool firmly during operation.
Dynamics of turning
Forces
The relative forces in a turning operation are important in the design of machine tools. The machine tool and its components must be able to withstand these forces without causing significant deflections, vibrations, or chatter during the operation. There are three principal forces during a turning process:
- The cutting or tangential force acts downward on the tool tip allowing deflection of the workpiece upward. It supplies the energy required for the cutting operation.The specific cutting force required to cut the material is called specific cutting force.Cutting force depends on the material.
- The axial or feed force acts in the longitudinal direction. It is also called the feed force because it is in the feed direction of the tool. This force tends to push the tool away from the chuck.
- The radial or thrust force acts in the radial direction and tends to push the tool away from the workpiece.
Speeds and feeds
Speeds and feeds for turning are chosen based on cutter material, workpiece material, setup rigidity, machine tool rigidity and spindle power, coolant choice, and other factors.
Feed
- The distance the tool advances into the material in one revolution is called "feed". It is specified as mm per revolution (mm/rev).
See also
References
- ^ a b Todd, Robert H.; Allen, Dell K.; Al ting, Leo (1994), Manufacturing Processes Reference Guide, Industrial Press Inc., p. 153, ISBN 0-8311-3049-0.
- ^ a b c d e f g Workshop Technology by W.A.J. Chapman Ph.D. M.Sc.(Eng.), M.I.Mech.E., M.I.Prod.E. Principal Hatfield College of Technology, Hertfordshire first published 1951 part one, two and three published by Edward Arnold (publishers Limited
- ^ a b Koepfer, Chris, "Hard Turning as an Alternative to Grinding", Production Machining, 1/22/2010. productionmachining.com, accessed 3/4/2010
- ^ "Threading On A Lathe : Modern Machine Shop". Mmsonline.com. 2003-01-15. Retrieved 2012-03-13.
External links
![](http://upload.wikimedia.org/wikipedia/en/thumb/4/4a/Commons-logo.svg/30px-Commons-logo.svg.png)
- "Lathe Introduction". Archived from the original on 2010-01-08. Retrieved 2010-01-08.
- Schneider, George. "Turning Tools and Operations." American Machinist, January, 2010.
- Lathe Turning Operations