Jump to content

Renault 100 hp V-12

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Stivushka (talk | contribs) at 08:17, 26 December 2023 (added Renault designation and number built (Hartmann)). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Renault 100 hp
Renault 100 hp
Type Piston inline aero engine
National origin France
Manufacturer Renault
First run c.1912[1]
Number built 35
Developed from Renault 90 hp
Developed into Renault 80 hp, Renault 130 hp

The Renault 100 hp, or 12B, aircraft engine from 1912 was a twelve-cylinder, air cooled 60° vee engine built by the French Renault company.

Design and development

Renault 100 hp V-12 engine, longitudinal section

The Renault 100 hp V-12 engine was development from an earlier 90 hp Renault V-12. The main change was the increased bore size of 96 mm instead of 90 mm in the 90 hp engine. Otherwise the general design of the engine was left relatively unchanged, and like its predecessor its general construction was derivative of the air-cooled Renault V-8 engines of the time, such as the 60 hp V-8 type.

The V-12 engine had its two rows of cylinders angled at 60 degree to each other and had a cylinder bore of 96 mm and a stroke of 140 mm. The cylinders and cylinder heads were separate cast-iron pieces with cast fins for air-cooling. The cylinder head was tightened to the cylinder with a copper-asbestos washer, and then secured by a cross-shaped clamp which was bolted to the crankcase with four long studs.[2] Airflow for cooling the cylinders was generated with a fan driven from the rear end of the crankshaft. The fan was blowing air into the sheet metal enclosed chamber between the two rows of cylinders, which then left the enclosure through the narrow spaces between the cylinders, passing through the cylinder's cooling-fins.

Renault 100 hp V-12 engine, cross section

A single camshaft was situated between the two rows of cylinders and operates the inlet and exhaust valves of both cylinder rows, with each valve operated by a separate cam on the camshaft. The inlet and exhaust valves sat vertically opposed in a lateral pocket of the cylinder head on the side of the combustion chamber, with the inlet valve situated below the exhaust valve. The inlet valve was operated directly from the camshaft via a tappet, whereas the exhaust valve was operated via a push rod and a rocker lever. The propeller was mounted directly on the camshaft, which was driven from the crankshaft via reduction gearing consisting of spur gears.

The lower part of the crankcase served as an oil reservoir. A pressurized oil lubrication system was fed by a gear pump located on the lowest point of the crankcase. The oil pump was driven over a vertical shaft from the camshaft via helical gears.[3] The crankshaft was supported by five plain intermediate bearings and two outer ball bearings. Contrary to their V-8 predecessors, the V-12 engines had master-and-slave connecting rods instead of the side-by-side placement of the connecting rods on the same crank journal.[4] This design was kept on the later Renault 80 hp V-8 and Renault 130 hp V-12 aircraft engines. The pistons were made of steel and were fitted with three cast iron rings.

A dual carburetor was fitted on one side of the crankcase, with each barrel of the carburetor feeding one cylinder row.[4] Ignition was supplied by two Bosch magnetos, with each magneto separately serving one cylinder row. The two magnetos were mounted transversely on the top of camshaft on the propeller end. The drive shafts of the magnetos were joined together and driven from the camshaft via helical gears.[3]

The engine was said to produce up to 110 hp at 1800 rpm.[4]

Applications

Specifications (Renault 100 hp)

Renault 100 hp V-12 engine, dimensioned drawing

Data from Angle,[2] Huth[6]

General characteristics

  • Type: 12-cylinder, 60-degree Vee, air-cooled in-line piston engine
  • Bore: 96 mm (3.780 in)
  • Stroke: 140 mm (5.512 in)
  • Length: 1,430 mm (56.3 in)
  • Width: 820 mm (32.3 in)
  • Height: 1,003 mm (39.5 in)
  • Dry weight: 290 kg (639 lb)

Components

Performance

  • Power output: 100 hp at 1,800 rpm

See also

Related development

Related lists

References

Notes

  1. ^ a b L'Aérophile. 1 October 1912. pp. 443-444
  2. ^ a b Angle. 1921. p. 414
  3. ^ a b Vorreiter. 1914. p. 82
  4. ^ a b c L'Aviation et l'automobilisme militaires : revue mensuelle des progrès scientifiques appliqués à la Défense nationale. March 1914. pp. 71-73
  5. ^ a b L'Aérophile. 15 September 1912. pp. 418-419
  6. ^ Huth. 1920. pp. 151-153

Bibliography

  • Angle, Glenn Dale (1921). Airplane Engine Encyclopedia: An Alphabetically Arranged Compilation Of All Available Data On The World's Airplane Engines. Otterbein Press. p. 414. OL 23525261M.
  • Fouqueux (1914). "Les "Renault"". L'Aviation et l'Automobilisme Militaires (in French). Paris. pp. 71-73.