Quantum-cascade laser
Quantum cascade lasers (QCLs) are semiconductor lasers that emit in the near- to far-infrared portion of the electromagnetic spectrum and were first demonstrated by Jerome Faist, Federico Capasso, Deborah Sivco, Carlo Sirtori, Albert Hutchinson, and Alfred Cho at Bell Laboratories in 1994.[1]
Unlike typical interband semiconductor lasers that emit electromagnetic radiation through the recombination of electron–hole pairs across the material band gap, QCLs are unipolar and laser emission is achieved through the use of intersubband transitions in a repeated stack of semiconductor superlattices, an idea first proposed in the paper "Possibility of amplification of electromagnetic waves in a semiconductor with a superlattice" by R.F. Kazarinov and R.A. Suris in 1971.[2]
Intersubband vs. interband transitions
Within a bulk semiconductor crystal, electrons may occupy states in one of two continuous energy bands - the valence band, which is heavily populated with low energy electrons and the conduction band, which is sparsely populated with high energy electrons. The two energy bands are separated by an energy band gap in which there are no permitted states available for electrons to occupy. Conventional semiconductor laser diodes generate light by a single photon of being emitted when a high energy electron in conduction band recombines with a hole in the valence band. The energy of the photon and hence the emission wavelength of laser diodes is therefore determined by the band gap of the material system used.
A QCL however does not use bulk semiconductor materials in its optically active region. Instead it comprises of a periodic series of thin layers of varying material composition forming a superlattice. The superlattice introduces a varying electric potential across the length of the device, meaning that there is a varying probability of electrons occupying different positions over the length of the device. This is referred to as one-dimensional multiple quantum well confinement and leads to the splitting of the band of permitted energies into a number of discrete electronic subbands. By suitable design of the layer thicknesses it is possible to engineer a population inversion between two subbands in the system which is required in order to achieve laser emission. Since the position of the energy levels in the system is primarily determined by the layer thicknesses and not the material, it is possible to tune the emission wavelength of QCLs over a wide range in the same material system.
Additionally, in semiconductor laser diodes, electrons and holes are annihilated after recombining across the band gap and can play no further part in photon generation. However in a unipolar QCL, once an electron has undergone an intersubband transition and emitted a photon in one period of the superlattice, it can tunnel into the next period of the structure where another photon can be emitted. This process of a single electron causing the emission of multiple photons as it traverses through the QCL structure gives rise to the name cascade and makes a quantum efficiency of greater than unity possible which leads to higher output powers than semiconductor laser diodes.
The independence of laser operation from the conduction and valence band edge characteristics makes laser operation from indirect bandgap materials such as the Si/SiGe is theoretically possible.[3]
Operating principles
Rate equations
![](http://upload.wikimedia.org/wikipedia/commons/thumb/f/fb/3level-qcl.png/400px-3level-qcl.png)
QCLs are typically based upon a three-level system. Assuming the formation of the wavefunctions is a fast process compared to the scattering between states, the time independent solutions to the Schrodinger equation may be applied and the system can be modelled using rate equations. Each subband contains a number of electrons (where is the subband index) which scatter between levels with a lifetime (reciprocal of the scattering rate ), where and are the initial and final subband indices. The rate equations of the three laser levels are given by
In the steady state, the time derivatives are equal to zero and . Under the assumption that absorption processes can be ignored (which is valid at low temperatures), the middle rate equation gives
Therefore if (i.e. ) then and a population inversion will exist. The population ratio is defined as
Active region designs
The scattering rates are tailored by suitable design of the layer thicknesses in the superlattice which determine the electron wave functions of the subbands. The scattering rate between two subbands is heavily dependent upon the overlap of the wave functions and energy spacing between the subbands .
![](http://upload.wikimedia.org/wikipedia/commons/thumb/5/53/3qw-qcl.png/400px-3qw-qcl.png)
The figure shows the wave functions in a three quantum well (3QW) QCL active region and injector.
In order to decrease , the overlap of the upper and lower laser levels is reduced. This is often achieved through designing the layer thicknesses such that the upper laser level is mostly localised in the left-hand well of the 3QW active region, while the lower laser level wave function is made to mostly reside in the central and right-hand wells. This is known as a diagonal transition. A vertical transition is one in which the upper laser level is localised in mainly the central and right-hand wells. This increases the overlap and hence which reduces the population inversion, but it increases the strength of the radiative transition and therefore the gain.
In order to increase , the lower laser level and the ground level wave functions are designed such that they have a good overlap. In order to increase further, the energy spacing between the subbands is designed such that it is equal to the longitudinal optical phonon energy (~36 meV in GaAs).
Material Systems
Emission wavelengths
Optical waveguides
In 1996, Claire Gmachl, a post-doctoral researcher at Bell Laboratories significantly reduced the linewidth of the QCL by incorporating a waveguide into the design, thus amplifying one particular wavelength.
Often a structure called a distributed feedback (DFB) is built on top of the laser crystal to prevent it from emitting at other than the desired wavelength.
Growth
The alternating layers of the two different semiconductors which form the quantum heterostructure are grown on to a substrate using molecular beam epitaxy (MBE) or metalorganic vapour phase epitaxy (MOVPE).
Applications
The laser's high optical power output, tuning range and room temperature operation make it useful for spectroscopic applications like the remote sensing of environmental gases and pollutants in the atmosphere. It may eventually be used for vehicular cruise control in conditions of poor visibility, collision avoidance radar, industrial process control, and medical diagnostics such as breath analyzers.
References
- ^ Faist, Jerome (1994). "Quantum Cascade Laser". Science. 264 (5158): 553–556. doi:10.1126/science.264.5158.553. Retrieved 2007-02-18.
{{cite journal}}
: Cite has empty unknown parameter:|quotes=
(help); Unknown parameter|coauthors=
ignored (|author=
suggested) (help); Unknown parameter|month=
ignored (help) - ^ Kazarinov, R.F (1971). "Possibility of amplification of electromagnetic waves in a semiconductor with a superlattice". Fizika i Tekhnika Poluprovodnikov. 5 (4): 797–800.
{{cite journal}}
: Cite has empty unknown parameter:|quotes=
(help); Unknown parameter|coauthors=
ignored (|author=
suggested) (help); Unknown parameter|month=
ignored (help) - ^ Paul, Douglas J (2004). Semicond. Sci. Technol. 19: R75–R108. doi:10.1088/0268-1242/19/10/R02 http://www.iop.org/EJ/abstract/0268-1242/19/10/R02. Retrieved 2007-02-18.
{{cite journal}}
: Cite has empty unknown parameters:|quotes=
,|coauthors=
, and|month=
(help); Missing or empty|title=
(help)