Doppler effect
This article needs additional citations for verification. (January 2008) |
![](http://upload.wikimedia.org/wikipedia/commons/thumb/f/f7/Doppler_effect_diagrammatic.png/470px-Doppler_effect_diagrammatic.png)
![](http://upload.wikimedia.org/wikipedia/commons/9/90/Dopplerfrequenz.gif)
The Doppler effect (or Doppler shift), named after Austrian physicist Christian Doppler who proposed it in 1842, is the change in frequency of a wave for an observer moving relative to the source of the wave. It is commonly heard when a vehicle sounding a siren or horn approaches, passes, and recedes from an observer. The received frequency is higher (compared to the emitted frequency) during the approach, it is identical at the instant of passing by, and it is lower during the recession.
For waves that propagate in a medium, such as sound waves, the velocity of the observer and of the source are relative to the medium in which the waves are transmitted. The total Doppler effect may therefore result from motion of the source, motion of the observer, or motion of the medium. Each of these effects is analyzed separately. For waves which do not require a medium, such as light or gravity in general relativity, only the relative difference in velocity between the observer and the source needs to be considered.
Development
Doppler first proposed the effect in 1842 in his treatise "Über das farbige Licht der Doppelsterne und einiger anderer Gestirne des Himmels" (On the coloured light of the binary stars and some other stars of the heavens).[1] The hypothesis was tested for sound waves by Buys Ballot in 1845. He confirmed that the sound's pitch was higher than the emitted frequency when the sound source approached him, and lower than the emitted frequency when the sound source receded from him. Hippolyte Fizeau discovered independently the same phenomenon on electromagnetic waves in 1848 (in France, the effect is sometimes called "effet Doppler-Fizeau"). In Britain, John Scott Russell made an experimental study of the Doppler effect (1848).[2]
An English translation of Doppler's 1842 treatise can be found in the book The Search for Christian Doppler by Alec Eden.[1]
General
In classical physics, where the speeds of source and the receiver relative to the medium are much lower compared to the speed of light, the relationship between observed frequency f and emitted frequency f0 is given by:
- where
- is the velocity of waves in the medium
- is the velocity of the receiver relative to the medium; positive if the receiver is moving towards the source.
- is the velocity of the source relative to the medium; positive if the source is moving away from the receiver.
The frequency is decreased if either is moving away from the other.
The above formula works for sound wave if and only if the speeds of the source and receiver relative to the medium are slower to the speed of sound. See also Sonic boom.
The above formula assumes that the source is either directly approaching or receding from the observer. If the source approaches the observer at an angle (but still with a constant velocity), the observed frequency that is first heard is higher than the object's emitted frequency. Thereafter, there is a monotonic decrease in the observed frequency as it gets closer to the observer, through equality when it is closest to the observer, and a continued monotonic decrease as it recedes from the observer. When the observer is very close to the path of the object, the transition from high to low frequency is very abrupt. When the observer is far from the path of the object, the transition from high to low frequency is gradual.
In the limit where the speed of the wave is much greater than the relative speed of the source and observer (this is often the case with electromagnetic waves, e.g. light), the relationship between observed frequency f and emitted frequency f0 is given by:
Observed frequency | Change in frequency |
---|---|
- where
- is the velocity of the source relative to the receiver: it is positive when the source and the receiver are moving away from each other.
- is the speed of wave (e.g. 3×108 m/s for electromagnetic waves travelling in a vacuum)
- is the wavelength of the transmitted wave in the reference frame of the source.
These two equations are only accurate to a first order approximation. However, they work reasonably well when the speed between the source and receiver is slow relative to the speed of the waves involved and the distance between the source and receiver is large relative to the wavelength of the waves. If either of these two approximations are violated, the formulae are no longer accurate.
Analysis
The frequency of the sounds that the source emits does not actually change. To understand what happens, consider the following analogy. Someone throws one ball every second in a man's direction. Assume that balls travel with constant velocity. If the thrower is stationary, the man will receive one ball every second. However, if the thrower is moving towards the man, he will receive balls more frequently because the balls will be less spaced out. The inverse is true if the thrower is moving away from the man. So it is actually the wavelength which is affected; as a consequence, the received frequency is also affected. It may also be said that the velocity of the wave remains constant whereas wavelength changes; hence frequency also changes.
If the source moving away from the observer is emitting waves through a medium with an actual frequency f0, then an observer stationary relative to the medium detects waves with a frequency f given by
where vs is positive if the source is moving away from the observer, and negative if the source is moving towards the observer.
A similar analysis for a moving observer and a stationary source yields the observed frequency (the receiver's velocity being represented as vr):
where the similar convention applies: vr is positive if the observer is moving towards the source, and negative if the observer is moving away from the source.
These can be generalized into a single equation with both the source and receiver moving.
With a relatively slow moving source, vs,r is small in comparison to v and the equation approximates to
where .
However the limitations mentioned above still apply. When the more complicated exact equation is derived without using any approximations (just assuming that source, receiver, and wave or signal are moving linearly relatively to each other) several interesting and perhaps surprising results are found. For example, as Lord Rayleigh noted in his classic book on sound, by properly moving it would be possible to hear a symphony being played backwards. This is the so-called "time reversal effect" of the Doppler effect. Other interesting conclusions are that the Doppler effect is time-dependent in general (thus we need to know not only the source and receivers' velocities, but also their positions at a given time), and in some circumstances it is possible to receive two signals or waves from a source, or no signal at all. In addition there are more possibilities than just the receiver approaching the signal and the receiver receding from the signal.
All these additional complications are derived for the classical, i.e., non-relativistic, Doppler effect, but hold for the relativistic Doppler effect as well.[citation needed]
A common misconception
Craig Bohren pointed out in 1991 that some physics textbooks erroneously state that the observed frequency increases as the object approaches an observer and then decreases only as the object passes the observer.[3] In most cases, the observed frequency of an approaching object declines monotonically from a value above the emitted frequency, through a value equal to the emitted frequency when the object is closest to the observer, and to values increasingly below the emitted frequency as the object recedes from the observer. Bohren proposed that this common misconception might occur because the intensity of the sound increases as an object approaches an observer and decreases once it passes and recedes from the observer and that this change in intensity is misperceived as a change in frequency. Higher sound pressure levels make for a small decrease in perceived pitch in low frequency sounds, and for a small increase in perceived pitch for high frequency sounds.[4]
Applications
![](http://upload.wikimedia.org/wikipedia/commons/thumb/7/7f/Doppler-effect-two-police-cars-diagram.png/350px-Doppler-effect-two-police-cars-diagram.png)
Sirens
The siren on a passing emergency vehicle will start out higher than its stationary pitch, slide down as it passes, and continue lower than its stationary pitch as it recedes from the observer. Astronomer John Dobson explained the effect thus:
- "The reason the siren slides is because it doesn't hit you."
In other words, if the siren approached the observer directly, the pitch would remain constant (as vs, r is only the radial component) until the vehicle hit him, and then immediately jump to a new lower pitch. Because the vehicle passes by the observer, the radial velocity does not remain constant, but instead varies as a function of the angle between his line of sight and the siren's velocity:
where vs is the velocity of the object (source of waves) with respect to the medium, and is the angle between the object's forward velocity and the line of sight from the object to the observer.
Astronomy
![](http://upload.wikimedia.org/wikipedia/commons/thumb/1/14/Redshift.png/200px-Redshift.png)
The Doppler effect for electromagnetic waves such as light is of great use in astronomy and results in either a so-called redshift or blue shift. It has been used to measure the speed at which stars and galaxies are approaching or receding from us, that is, the radial velocity. This is used to detect if an apparently single star is, in reality, a close binary and even to measure the rotational speed of stars and galaxies.
The use of the Doppler effect for light in astronomy depends on our knowledge that the spectra of stars are not continuous. They exhibit absorption lines at well defined frequencies that are correlated with the energies required to excite electrons in various elements from one level to another. The Doppler effect is recognizable in the fact that the absorption lines are not always at the frequencies that are obtained from the spectrum of a stationary light source. Since blue light has a higher frequency than red light, the spectral lines of an approaching astronomical light source exhibit a blue shift and those of a receding astronomical light source exhibit a redshift.
Among the nearby stars, the largest radial velocities with respect to the Sun are +308 km/s (BD-15°4041, also known as LHS 52, 81.7 light-years away) and -260 km/s (Woolley 9722, also known as Wolf 1106 and LHS 64, 78.2 light-years away). Positive radial velocity means the star is receding from the Sun, negative that it is approaching.
Temperature measurement
Another use of the Doppler effect, which is found mostly in plasma physics and astronomy, is the estimation of the temperature of a gas (or ion temperature in a plasma) which is emitting a spectral line. Due to the thermal motion of the emitters, the light emitted by each particle can be slightly red- or blue-shifted, and the net effect is a broadening of the line. This line shape is called a Doppler profile and the width of the line is proportional to the square root of the temperature of the emitting species, allowing a spectral line (with the width dominated by the Doppler broadening) to be used to infer the temperature.
Radar
The Doppler effect is used in some types of radar, to measure the velocity of detected objects. A radar beam is fired at a moving target — e.g. a motor car, as police use radar to detect speeding motorists — as it approaches or recedes from the radar source. Each successive radar wave has to travel farther to reach the car, before being reflected and re-detected near the source. As each wave has to move farther, the gap between each wave increases, increasing the wavelength. In some situations, the radar beam is fired at the moving car as it approaches, in which case each successive wave travels a lesser distance, decreasing the wavelength. In either situation, calculations from the Doppler effect accurately determine the car's velocity. Moreover, the proximity fuze, developed during World War II, relies upon Doppler radar to explode at the correct time, height, distance, etc.[citation needed]
Medical imaging and blood flow measurement
An echocardiogram can, within certain limits, produce accurate assessment of the direction of blood flow and the velocity of blood and cardiac tissue at any arbitrary point using the Doppler effect. One of the limitations is that the ultrasound beam should be as parallel to the blood flow as possible. Velocity measurements allow assessment of cardiac valve areas and function, any abnormal communications between the left and right side of the heart, any leaking of blood through the valves (valvular regurgitation), and calculation of the cardiac output. Contrast-enhanced ultrasound using gas-filled microbubble contrast media can be used to improve velocity or other flow-related medical measurements.
Although "Doppler" has become synonymous with "velocity measurement" in medical imaging, in many cases it is not the frequency shift (Doppler shift) of the received signal that is measured, but the phase shift (when the received signal arrives).
Velocity measurements of blood flow are also used in other fields of medical ultrasonography, such as obstetric ultrasonography and neurology. Velocity measurement of blood flow in arteries and veins based on Doppler effect is an effective tool for diagnosis of vascular problems like stenosis.[5]
Flow measurement
Instruments such as the laser Doppler velocimeter (LDV), and acoustic Doppler velocimeter (ADV) have been developed to measure velocities in a fluid flow. The LDV emits a light beam and the ADV emits an ultrasonic acoustic burst, and measure the Doppler shift in wavelengths of reflections from particles moving with the flow. The actual flow is computed as a function of the water velocity and face. This technique allows non-intrusive flow measurements, at high precision and high frequency.
Velocity profile measurement
Developed originally for velocity measurements in medical applications (blood flows), Ultrasonic Doppler Velocimetry (UDV) can measure in real time complete velocity profile in almost any liquids containing particles in suspension such as dust, gas bubbles, emulsions. Flows can be pulsating, oscillating, laminar or turbulent, stationary or transient. This technique is fully non-invasive.
Underwater acoustics
In military applications the Doppler shift of a target is used to ascertain the speed of a submarine using both passive and active sonar systems. As a submarine passes by a passive sonobuoy, the stable frequencies undergo a Doppler shift, and the speed and range from the sonobuoy can be calculated. If the sonar system is mounted on a moving ship or another submarine, then the relative velocity can be calculated.
Audio
The Leslie speaker, associated with and predominantly used with the Hammond B-3 organ, takes advantage of the Doppler Effect by using an electric motor to rotate an acoustic horn around a loudspeaker, sending its sound in a circle. This results at the listener's ear in rapidly fluctuating frequencies of a keyboard note.
Vibration measurement
A laser Doppler vibrometer (LDV) is a non-contact method for measuring vibration. The laser beam from the LDV is directed at the surface of interest, and the vibration amplitude and frequency are extracted from the Doppler shift of the laser beam frequency due to the motion of the surface.
See also
- Relativistic Doppler effect
- Dopplergraph
- Fizeau experiment
- Fading
- Photoacoustic Doppler effect
- Rayleigh fading
References
- ^ a b Alec Eden The search for Christian Doppler,Springer-Verlag, Wien 1992. Contains a facsimile edition with an English translation.
- ^ Scott Russell, John (1848). "On certain effects produced on sound by the rapid motion of the observer". Report of the Eighteen Meeting of the British Association for the Advancement of Science. 18 (7). John Murray, London in 1849: 37–38. Retrieved 2008-07-08.
- ^ Bohren, C. F. (1991). What light through yonder window breaks? More experiments in atmospheric physics. New York: J. Wiley.
- ^ Olson, Harry F. (1967). Music, Physics and Engineering. Dover Publications. pp. 248–251. ISBN 0486217698.
- ^ D. H. Evans and W. N. McDicken, Doppler Ultrasound, Second Edition, John Wiley and Sons, 2000.
Further reading
- "Doppler and the Doppler effect", E. N. da C. Andrade, Endeavour Vol. XVIII No. 69, January 1959 (published by ICI London). Historical account of Doppler's original paper and subsequent developments.
- Adrian, Eleni (24 June, 1995). "Doppler Effect". NCSA. Retrieved 2008-07-13.
{{cite web}}
: Check date values in:|date=
(help)
External links
![](http://upload.wikimedia.org/wikipedia/en/thumb/4/4a/Commons-logo.svg/30px-Commons-logo.svg.png)
- Doppler Effect, ScienceWorld
- Java simulation of Doppler effect
- Doppler Shift for Sound and Light at MathPages
- The Doppler Effect and Sonic Booms (D.A. Russell, Kettering University)
- Video Mashup with Doppler Effect videos
- Practical Doppler flow meters- Doppler flow meters with engineering examples and applications
- Wave Propagation from John de Pillis. An animation showing that the speed of a moving wave source does not affect the speed of the wave.
- EM Wave Animation from John de Pillis. How an electromagnetic wave propagates through a vacuum
- Signal-Processing - Ultrasonic Doppler Velocimeters for real time measurement of velocity profiles in liquids
- Doppler Shift Demo - Interactive flash simulation for demonstrating Doppler shift.
- [1] Excellent interactive applet, go to applet thumbnails>upcoming applets.