Thermoelectric effect
![]() | This article may require copy editing for grammar, style, cohesion, tone, or spelling. (September 2010) |
- This page is about the thermoelectric effect as a physical phenomenon. For applications of the thermoelectric effect, see thermoelectric materials, thermoelectric generator, and thermoelectric cooling.
Thermoelectric effect |
---|
![]() |
The thermoelectric effect is the direct conversion of temperature differences to electric voltage and vice versa. A thermoelectric device creates a voltage when there is a different temperature on each side. Conversely when a voltage is applied to it, it creates a temperature difference (known as the Peltier effect). At atomic scale (specifically, charge carriers), an applied temperature gradient causes charged carriers in the material, whether they are electrons or electron holes, to diffuse from the hot side to the cold side, similar to a classical gas that expands when heated; hence, the thermally induced current.
This effect can be used to generate electricity, to measure temperature, to cool objects, or to heat them or cook them. Because the direction of heating and cooling is determined by the polarity of the applied voltage, thermoelectric devices make very convenient temperature controllers.
Traditionally, the term thermoelectric effect or thermoelectricity encompasses three separately identified effects, the Seebeck effect, the Peltier effect, and the Thompson effect. In many textbooks, thermoelectric effect may also be called the Peltier–Seebeck effect. This separation derives from the independent discoveries of French physicist Jean Charles Athanase Peltier and Estonian-German physicist Thomas Johann Seebeck. Joule heating, the heat that is generated whenever a voltage is applied across a resistive material, is somewhat related, though it is not generally termed a thermoelectric effect (and it is usually regarded as being a loss mechanism due to non-ideality in thermoelectric devices). The Peltier–Seebeck and Thomson effects can in principle be thermodynamically reversible,[1] whereas Joule heating is not.
Seebeck effect
The Seebeck effect is the conversion of temperature differences directly into electricity.
Seebeck discovered that a compass needle would be deflected when a closed loop was formed of two metals joined in two places with a temperature difference between the junctions. This is because the metals respond differently to the temperature difference, which creates a current loop, which produces a magnetic field. Seebeck, however, at this time did not recognize there was an electric current involved, so he called the phenomenon the thermomagnetic effect, thinking that the two metals became magnetically polarized by the temperature gradient. The Danish physicist Hans Christian Ørsted played a vital role in explaining and conceiving the term "thermoelectricity".
The effect is that a voltage, the thermoelectric EMF, is created in the presence of a temperature difference between two different metals or semiconductors. This causes a continuous current in the conductors if they form a complete loop. The voltage created is of the order of several microvolts per kelvin difference. One such combination, copper-constantan, has a Seebeck coefficient of 41 microvolts per kelvin at room temperature.[citation needed]
In the circuit:
(which can be in several different configurations and be governed by the same equations), the voltage developed can be derived from:
SA and SB are the Seebeck coefficients (also called thermoelectric power or thermopower) of the metals A and B as a function of temperature, and T1 and T2 are the temperatures of the two junctions. The Seebeck coefficients are non-linear as a function of temperature, and depend on the conductors' absolute temperature, material, and molecular structure. If the Seebeck coefficients are effectively constant for the measured temperature range, the above formula can be approximated as:
The Seebeck effect is commonly used in a device called a thermocouple (because it is made from a coupling or junction of materials, usually metals) to measure a temperature difference directly or to measure an absolute temperature by setting one end to a known temperature. A metal of unknown composition can be classified by its thermoelectric effect if a metallic probe of known composition, kept at a constant temperature, is held in contact with it. Industrial quality control instruments use this Seebeck effect to identify metal alloys. This is known as thermoelectric alloy sorting.
Several thermocouples connected in series are called a thermopile, which is sometimes constructed in order to increase the output voltage since the voltage induced over each individual couple is small.
This is also the principle at work behind thermoelectric generators (such as radioisotope thermoelectric generators or RTGs) which are used for creating power from heat differentials.
The Seebeck effect is due to two effects: charge carrier diffusion and phonon drag (described below). [citation needed]
Thermopower
The thermopower, thermoelectric power, or Seebeck coefficient of a material measures the magnitude of an induced thermoelectric voltage in response to a temperature difference across that material. The thermopower has units of (V/K), though in practice it is more common to use microvolts per kelvin. Values in the hundreds of μV/K, negative or positive, are typical of good thermoelectric materials. The term thermopower is a misnomer since it measures the voltage or electric field induced in response to a temperature difference, not the electric power. An applied temperature difference causes charged carriers in the material, whether they are electrons or holes, to diffuse from the hot side to the cold side, similar to a classical gas that expands when heated. Mobile charged carriers migrating to the cold side leave behind their oppositely charged and immobile nuclei at the hot side thus giving rise to a thermoelectric voltage (thermoelectric refers to the fact that the voltage is created by a temperature difference). Since a separation of charges also creates an electric potential, the buildup of charged carriers onto the cold side eventually ceases at some maximum value since there exists an equal amount of charged carriers drifting back to the hot side as a result of the electric field at equilibrium. Only an increase in the temperature difference can resume a buildup of more charge carriers on the cold side and thus lead to an increase in the thermoelectric voltage. Incidentally the thermopower also measures the entropy per charge carrier in the material. To be more specific, the partial molar electronic entropy is said to equal the absolute thermoelectric power multiplied by the negative of Faraday's constant.[2]
The thermopower of a material, represented by (or sometimes by ), depends on the material's temperature and crystal structure. Typically metals have small thermopowers because most have half-filled bands. Electrons (negative charges) and holes (positive charges) both contribute to the induced thermoelectric voltage thus canceling each other's contribution to that voltage and making it small. In contrast, semiconductors can be doped with excess electrons or holes, and thus can have large positive or negative values of the thermopower depending on the charge of the excess carriers. The sign of the thermopower can determine which charged carriers dominate the electric transport in both metals and semiconductors.[citation needed]
If the temperature difference between the two ends of a material is small, then the thermopower of a material is defined (approximately)[3] as:
and a thermoelectric voltage ΔV is seen at the terminals.
This can also be written in relation to the electric field and the temperature gradient , by the approximate[3] equation:
In practice one rarely measures the absolute thermopower of the material of interest. This is because electrodes attached to a voltmeter must be placed onto the material in order to measure the thermoelectric voltage. The temperature gradient then also typically induces a thermoelectric voltage across one leg of the measurement electrodes. Therefore the measured thermopower includes a contribution from the thermopower of the material of interest and the material of the measurement electrodes.
The measured thermopower is then a contribution from both and can be written as:
Superconductors have zero thermopower since the charged carriers produce no entropy. This allows a direct measurement of the absolute thermopower of the material of interest, since it is the thermopower of the entire thermocouple as well. In addition, a measurement of the Thomson coefficient, , of a material can also yield the thermopower through the relation:
The thermopower is an important material parameter that determines the efficiency of a thermoelectric material. A larger induced thermoelectric voltage for a given temperature gradient will lead to a larger efficiency. Ideally one would want very large thermopower values since only a small amount of heat is then necessary to create a large voltage. This voltage can then be used to provide power.[citation needed]
Charge-carrier diffusion
Charge carriers in the materials (electrons in metals, electrons and holes in semiconductors, ions in ionic conductors) will diffuse when one end of a conductor is at a different temperature to the other. Hot carriers diffuse from the hot end to the cold end, since there is a lower density of hot carriers at the cold end of the conductor. Cold carriers diffuse from the cold end to the hot end for the same reason.
If the conductor were left to reach thermodynamic equilibrium, this process would result in heat being distributed evenly throughout the conductor (see heat transfer). The movement of heat (in the form of hot charge carriers) from one end to the other is called a heat current. As charge carriers are moving, it is also an electric current.
In a system where both ends are kept at a constant temperature difference (a constant heat current from one end to the other), there is a constant diffusion of carriers. If the rate of diffusion of hot and cold carriers in opposite directions were equal, there would be no net change in charge. However, the diffusing charges are scattered by impurities, imperfections, and lattice vibrations (phonons). If the scattering is energy dependent, the hot and cold carriers will diffuse at different rates. This creates a higher density of carriers at one end of the material, and the distance between the positive and negative charges produces a potential difference; an electrostatic voltage.
This electric field, however, opposes the uneven scattering of carriers, and an equilibrium is reached where the net number of carriers diffusing in one direction is canceled by the net number of carriers moving in the opposite direction from the electrostatic field. This means the thermopower of a material depends greatly on impurities, imperfections, and structural changes (which often vary themselves with temperature and electric field), and the thermopower of a material is a collection of many different effects.[citation needed]
Early thermocouples were metallic, but many more recently developed thermoelectric devices are made from alternating p-type and n-type semiconductor elements connected by metallic interconnects as pictured in the figures below. Semiconductor junctions are especially common in power generation devices, while metallic junctions are more common in temperature measurement. Charge flows through the n-type element, crosses a metallic interconnect, and passes into the p-type element. If a power source is provided, the thermoelectric device may act as a cooler, as in the figure to the left below. This is the Peltier effect, described below. Electrons in the n-type element will move opposite the direction of current and holes in the p-type element will move in the direction of current, both removing heat from one side of the device. If a heat source is provided, the thermoelectric device may function as a power generator, as in the figure to the right below. The heat source will drive electrons in the n-type element toward the cooler region, thus creating a current through the circuit. Holes in the p-type element will then flow in the direction of the current. The current can then be used to power a load, thus converting the thermal energy into electrical energy.[citation needed]
Phonon drag
Phonons are not always in local thermal equilibrium; they move against the thermal gradient. They lose momentum by interacting with electrons (or other carriers) and imperfections in the crystal. If the phonon-electron interaction is predominant, the phonons will tend to push the electrons to one end of the material, losing momentum in the process. This contributes to the already present thermoelectric field. This contribution is most important in the temperature region where phonon-electron scattering is predominant. This happens for
where θD is the Debye temperature. At lower temperatures there are fewer phonons available for drag, and at higher temperatures they tend to lose momentum in phonon-phonon scattering instead of phonon-electron scattering.
This region of the thermopower-versus-temperature function is highly variable under a magnetic field.[citation needed]
Peltier effect
The Peltier (Template:Pron-en) effect bears the name of Jean-Charles Peltier, a French physicist who in 1834 discovered the calorific effect of an electric current at the junction of two different metals. When a current is made to flow through the circuit, heat is evolved at the upper junction (at T2), and absorbed at the lower junction (at T1). The Peltier heat absorbed by the lower junction per unit time, is equal to
where π is the Peltier coefficient ΠAB of the entire thermocouple, and ΠA and ΠB are the coefficients of each material. p-type silicon typically has a positive Peltier coefficient (though not above ~550 K), and n-type silicon is typically negative.
The Peltier coefficients represent how much heat current is carried per unit charge through a given material. Since charge current must be continuous across a junction, the associated heat flow will develop a discontinuity if ΠA and ΠB are different. This causes a non-zero divergence at the junction and so heat must accumulate or deplete there, depending on the sign of the current. Another way to understand how this effect could cool a junction is to note that when electrons flow from a region of high density to a region of low density, this "expansion" causes cooling (as with an ideal gas).[citation needed]
The carriers are attempting to return to the electron equilibrium that existed before the current was applied by absorbing energy at one connector and releasing it at the other. The individual couples can be connected in series to enhance the effect.
An interesting consequence of this effect is that the direction of heat transfer is controlled by the polarity of the current; reversing the polarity will change the direction of transfer and thus the sign of the heat absorbed/evolved.
A Peltier cooler/heater or thermoelectric heat pump is a solid-state active heat pump which transfers heat from one side of the device to the other. Peltier cooling is also called thermo-electric cooling (TEC).[citation needed]
Thomson effect
The Thomson effect was predicted and subsequently experimentally observed by William Thomson (Lord Kelvin) in 1851. It describes the heating or cooling of a current-carrying conductor with a temperature gradient.
Any current-carrying conductor (except for a superconductor), with a temperature difference between two points, will either absorb or emit heat, depending on the material.
If a current density J is passed through a homogeneous conductor, heat production per unit volume is:
where
ρ is the resistivity of the material
dT/dx is the temperature gradient along the wire
μ is the Thomson coefficient.
The first term ρ J² is simply the Joule heating, which is not reversible.
The second term is the Thomson heat, which changes sign when J changes direction.
In metals such as zinc and copper, which have a hotter end at a higher potential and a cooler end at a lower potential, when current moves from the hotter end to the colder end, it is moving from a high to a low potential, so there is an evolution of heat. This is called the positive Thomson effect.[citation needed]
In metals such as cobalt, nickel, and iron, which have a cooler end at a higher potential and a hotter end at a lower potential, when current moves from the hotter end to the colder end, it is moving from a low to a high potential, there is an absorption of heat. This is called the negative Thomson effect.
The Thomson coefficient is unique among the three main thermoelectric coefficients because it is the only thermoelectric coefficient directly measurable for individual materials. The Peltier and Seebeck coefficients can only be determined for pairs of materials. Thus, there is no direct experimental method to determine an absolute Seebeck coefficient (i.e. thermopower) or absolute Peltier coefficient for an individual material. However, as mentioned elsewhere in this article there are two equations, the Thomson relations, also known as the Kelvin relations (see below), relating the three thermoelectric coefficients. Therefore, only one can be considered unique.[citation needed]
If the Thomson coefficient of a material is measured over a wide temperature range, including temperatures close to zero, one can then integrate the Thomson coefficient over the temperature range using the Kelvin relations to determine the absolute (i.e. single-material) values for the Peltier and Seebeck coefficients. In principle, this need only be done for one material, since all other values can be determined by measuring pairwise Seebeck coefficients in thermocouples containing the reference material and then adding back the absolute thermoelecric power (thermopower) of the reference material.
It is commonly asserted that lead has a zero Thomson effect. While it is true that the thermoelectric coefficients of lead are small, they are in general non-zero. The Thomson coefficient of lead has been measured over a wide temperature range and has been integrated to calculate the absolute thermoelectric power (thermopower) of lead as a function of temperature.[4]
Unlike lead, the thermoelectric coefficients of all known superconductors are zero.[citation needed]
The Thomson relationships
The Seebeck effect is a combination of the Peltier and Thomson effects. In 1854 Thomson found two relationships, now called the Thomson or Kelvin relationships, between the corresponding coefficients. The absolute temperature T, the Peltier coefficient and Seebeck coefficient S are related by the second Thomson relation
which predicted the Thomson effect before it was actually formalized. These are related to the Thomson coefficient by the first Thomson relation
Thomson's theoretical treatment of thermoelectricity is remarkable in the fact that it is probably the first attempt to develop a reasonable theory of irreversible thermodynamics (non-equilibrium thermodynamics). This occurred at about the time that Clausius, Thomson, and others were introducing and refining the concept of entropy.[citation needed]
Figure of merit
The figure of merit for thermoelectric devices is defined as
- ,
where σ is the electrical conductivity, κ is the thermal conductivity, and S is the Seebeck coefficient or thermopower (conventionally in μV/K). This is more commonly expressed as the dimensionless figure of merit ZT by multiplying it with the average temperature (). Greater values of ZT indicate greater thermodynamic efficiency, subject to certain provisions, particularly the requirement that the two materials of the couple have similar Z values. ZT is therefore a very convenient figure for comparing the potential efficiency of devices using different materials. Values of ZT=1 are considered good, and values of at least the 3–4 range are considered to be essential for thermoelectrics to compete with mechanical generation and refrigeration in efficiency. To date, the best reported ZT values have been in the 2–3 range.[5][6][7] Much research in thermoelectric materials has focused on increasing the Seebeck coefficient and reducing the thermal conductivity, especially by manipulating the nanostructure of the materials.[citation needed]
Device efficiency
The efficiency of a thermoelectric device for electricity generation is given by η, defined as
- , and
where TH is the temperature at the hot junction and TC is the temperature at the surface being cooled. is the modified dimensionless figure of merit which now takes into consideration the thermoelectric capacity of both thermoelectric materials being used in the power generating device, and is defined as
where ρ is the electrical resistivity, is the average temperature between the hot and cold surfaces, and the subscripts n and p denote properties related to the n- and p-type semiconducting thermoelectric materials, respectively. It is worthwhile to note that the efficiency of a thermoelectric device is limited by the Carnot efficiency (hence the TH and TC terms in Φmax ), since thermoelectric devices are still inherently heat engines.
The COP of current commercial thermoelectric refrigerators ranges from 0.3 to 0.6, only about one-sixth the value of traditional vapor-compression refrigerators.[8]
Uses
Seebeck effect
The Seebeck effect can be used to turn any heat source into electrical power. These devices, called thermoelectric generators (or "thermogenerators") function like a heat engine, but less bulky, with no moving parts, and typically more expensive and less efficient.
Any power plant produces waste heat, which can be used to generate additional power using a thermoelectric generator (a form of energy recycling). This is potentially an enormous market.
Automobiles also produce waste heat, and harvesting it could increase fuel efficiency. For more information see Automotive Thermoelectric Generators.
Space probes often use Radioisotope thermoelectric generators.
Solar cells use only the high frequency part of the radiation, while the low frequency heat energy is wasted. Several patents about the use of thermoelectric devices in tandem with solar cells have been filed. The idea is to increase the efficiency of the combined solar/thermoelectric system to convert the solar radiation into useful electricity.[citation needed]
Peltier effect
The Peltier effect can be used to create a refrigerator which is compact and has no circulating fluid or moving parts. For more information see Peltier cooler.[citation needed]
Temperature measurement
Thermocouples and thermopiles are commonly used to measure temperatures. They use the Seebeck effect. More precisely, they do not directly measure temperature, they measure temperature differences between the probe and the voltmeter at the other end of the wires. The temperature of the voltmeter, usually the same as room temperature, can be measured separately using "cold junction compensation" techniques.[citation needed]
See also
- Heat transfer
- Joule's laws
- Pyroelectricity – the creation of an electric field in a crystal after uniform heating
- Spintronics
- Thermionic emission
- Thermoacoustic refrigeration
- Thermodiffusion
- Thermoelectric cooling
- Thermoelectricity
- Thermoelectric generator
- Thermopile
- Thermopower
References
- ^ As the "figure of merit" (denoted Z, discussed below) approaches infinity, the Peltier–Seebeck effect can drive a heat engine or refrigerator at closer and closer to the Carnot efficiency. See DiSalvo, "Thermoelectric Cooling and Power Generation", Science 1999, Web link. Any device that works at the Carnot efficiency is thermodynamically reversible, a consequence of classical thermodynamics.
- ^ Rockwood, Alan L. (1984). "Relationship of thermoelectricity to electronic entropy". Phys. Rev. A. 30: 2843–4. doi:10.1103/PhysRevA.30.2843.
{{cite journal}}
: More than one of|author=
and|last1=
specified (help) - ^ a b Strictly speaking, these two expressions for the Seebeck coefficient are only approximate: The numerator of the first equation should be the difference in (electrochemical potential divided by -e), not electric potential, and likewise the second equation should have the gradient of electrochemical potential divided by e rather than the electric field. However, the chemical potential is often relatively constant as a function of temperature, so using electric potential alone is in these cases a very good approximation. See Taylor, 1973. Although many textbooks use the approximate definition (involving the electric field and/or electric potential), a few give the exact expression; for example, see Physics of transition metal oxides by Sadamichi Maekawa, page 323, or Thermoelectrics: Basic Principles and New Materials Developments by Nolas et al., page 38.
- ^ Roberts, R.B. (1977). "Absolute scale of thermoelectricity". Nature. 265: 226–7. doi:10.1038/265226a0.
{{cite journal}}
: More than one of|author=
and|last1=
specified (help) - ^ Katie Walter (2007). "A Quantum contribution to Technology". Lawrence Livermore National Laboratory.
{{cite web}}
: Unknown parameter|month=
ignored (help) - ^ R. Venkatasubramanian, E. Siivola, T. Colpitts, and B. O’Quinn, Nature 413, 597 2001.
- ^ T. C. Harman, M. P. Walsh, B. E. Laforge, and G. W. Turner, J. Electron. Mater. 34, L19 2005
- ^ Solar refrigeration options – a state-of-the-art review. D.S. Kim, C.A. Infante Ferreira. 2008, International Journal of Refrigeration, pp. 3–15. DOI web link
- Besançon, Robert M. (1985). The Encyclopedia of Physics, Third Edition. Van Nostrand Reinhold Company. ISBN 0-442-25778-3.
- Rowe, D. M., ed. (2006). Thermoelectrics Handbook:Macro to Nano. Taylor & Francis. ISBN 0-8493-2264-2.
- Ioffe, A.F. (1957). Semiconductor Thermoelements and Thermoelectric Cooling. Infosearch Limited. ISBN 0-8508-6039-3.
- Thomson, William (1851). "On a mechanical theory of thermoelectric currents". Proc.Roy.Soc.Edinburgh: 91–98.
External links
General
- Thomson Effect – Interactive Java Tutorial National High Magnetic Field Laboratory
- International Thermoelectric Society
- Thermoelectric News
- General
- Explanation of carrier diffusion and phonon drag components of thermopower
- Good explanation of thermo-electric cooler design
- BSST Technical Papers on thermoelectric devices
Semiconductors
Metals
Related
- The 8th European Conference on Thermoelectrics, ECT 2010, to be held Sept. 22–24, 2010 in Como, Italy, organized by the Lecco unit of the Institute of Energetics and Interphases (IENI) of the Italian National research Council (CNR)
- A news article on the increases in thermal diode efficiency
- A fan for putting on top of stoves and other hot items, powered by the Peltier-Seebeck effect.
- Generating useful voltages (and powering radio transmitters) from Peltier devices