Hydraulic motor
![]() | This article may require copy editing for grammar, style, cohesion, tone, or spelling. (November 2013) |
This article needs additional citations for verification. (December 2009) |
![](http://upload.wikimedia.org/wikipedia/commons/thumb/c/c2/Moteur_hydraulique_staffa.jpg/220px-Moteur_hydraulique_staffa.jpg)
A hydraulic motor is a mechanical actuator that converts hydraulic pressure and flow into torque and angular displacement (rotation). The hydraulic motor is the rotary counterpart of the hydraulic cylinder.
Conceptually, a hydraulic motor should be interchangeable with a hydraulic pump because it performs the opposite function - similar to the way a DC electric motor is theoretically interchangeable with a DC electrical generator. However, most hydraulic pumps cannot be used as hydraulic motors because they cannot be backdriven. Also, a hydraulic motor is usually designed for working pressure at both sides of the motor.
Hydraulic pumps, motors, and cylinders can be combined into hydraulic drive systems. One or more hydraulic pumps, coupled to one or more hydraulic motors, constitute a hydraulic transmission.
![](http://upload.wikimedia.org/wikipedia/commons/thumb/7/76/Machine_Room._Swing_Bridge_-_geograph.org.uk_-_486049.jpg/220px-Machine_Room._Swing_Bridge_-_geograph.org.uk_-_486049.jpg)
One of the first rotary hydraulic motors to be developed was that constructed by Armstrong for his Swing Bridge over the River Tyne. Two motors were provided, for reliability. Each one was a three-cylinder single-acting oscillating engine. Armstrong developed a wide range of hydraulic motors, linear and rotary, that were used for a wide range of industrial and civil engineering tasks, particularly for docks and moving bridges.
Hydraulic motor types
![](http://upload.wikimedia.org/wikipedia/commons/thumb/7/7f/Symbol_Hydro_motor.svg/60px-Symbol_Hydro_motor.svg.png)
- For an explanation of plunger and piston, see hydraulic cylinder
Many designs are possible. The following types of hydraulic motors are available:
Gear and vane motors
![](http://upload.wikimedia.org/wikipedia/commons/thumb/1/19/Hydraulikmotor.jpg/220px-Hydraulikmotor.jpg)
Gear and vane motors are used in simple rotating systems. Their benefits include low initial cost and high rpm.
A gear motor (external gear) consists of two gears, the driven gear (attached to the output shaft by way of a key, etc.) and the idler gear. High pressure oil is ported into one side of the gears, where it flows around the periphery of the gears, between the gear tips and the wall housings in which it resides, to the outlet port. The gears then mesh, not allowing the oil from the outlet side to flow back to the inlet side. For lubrication, the gear motor uses a small amount of oil from the pressurized side of the gears, bleeds this through the (typically) hydrodynamic bearings, and vents the same oil either to the low pressure side of the gears, or through a dedicated drain port on the motor housing. An especially positive attribute of the gear motor is that catastrophic breakdown is a lot less common than in most other types of hydraulic motors. This is because the gears gradually wear down the housing and/or main bushings, reducing the volumetric efficiency of the motor gradually until it is all but useless. This often happens long before wear causes the unit to seize or break down.
A vane motor consists of a housing with an eccentric bore, in which runs a rotor with vanes in it that slide in and out. The force differential created by the unbalanced force of the pressurized fluid on the vanes causes the rotor to spin in one direction. A critical element in vane motor design is how the vane tips are machined at the contact point between vane tip and motor housing. Several type of "lip" designs are used, and the main objective is to provide a tight seal between the inside of the motor housing and the vane, and at the same time to minimize wear and metal-to-metal contact.
Gerotor motors
![](http://upload.wikimedia.org/wikipedia/commons/thumb/d/de/Gerotor_anm.gif/220px-Gerotor_anm.gif)
The gerotor motor is in essence a rotor with N-1 teeth, rotating off center in a rotor/stator with N teeth. Pressurized fluid is guided into the assembly using a (usually) axially placed plate-type distributor valve. Several different designs exist, such as the Geroller (internal or external rollers) and Nichols motors. Typically, the Gerotor motors are low-to-medium speed and medium-to-high torque.
Axial plunger motors
For high quality rotating drive systems plunger motors are generally used. Whereas the speed of hydraulic pumps ranges from 1200 to 1800 rpm, the machinery to be driven by the motor often requires a much lower speed. This means that when an axial plunger motor (swept volume maximum 2 litres) is used, a gearbox is usually needed. For a continuously adjustable swept volume, axial piston motors are used. PISTON TYPE.— Like piston (reciprocating) type pumps, the most common design of the piston type of motor is the axial. This type of motor is the most commonly used in hydraulic systems. These motors are, like their pump counterparts, available in both variable and fixed displacement designs. Typical usable (within acceptable efficiency) rotational speeds range from below 50rpm and up to and above 14000rpm. Efficiencies and minimum/maximum rotational speeds are highly dependent on the design of the rotating group, and many different types are in use.
Radial piston motors
![](http://upload.wikimedia.org/wikipedia/commons/thumb/b/b9/Moteur_Hydraulique_Calzoni.jpg/220px-Moteur_Hydraulique_Calzoni.jpg)
Radial piston motors are available in two basic types. Crankshaft type (e.g. Staffa or Sai Hydraulic Motors) with a single cam and pistons pushing inwards. This type of motor is basically an old design but is one which has extremely high starting torque characteristics. They are available in displacements from 40cc/rev up to about 50 litres/rev but can sometimes be limited in power output. Crankshaft type Radial Piston Motors are capable of running at "creep" speeds and some can run seamlessly up to 1500 rpm whilst offering virtually constant output Torque chacteristics. This makes them still the most versatile design.
Multilobe cam ring type (e.g. Hägglunds or Poclain type) has a cam ring with multiple lobes and the piston rollers push outwardly against the cam ring. This produces a very smooth output with high starting torque but they are often limited in the upper speed range. This type of motor is available in a very wide range from about 1 litre/rev to 250 litres/rev. These motors are particularly good on low speed applications and can develop very high power.
Braking
Hydraulic motors usually have a drain connection for the internal leakage, which means that when the power unit is turned off the hydraulic motor in the drive system will move if an external load is acting on it, such as a crane or winch with suspended load. In these cases there is always a need for a brake or a locking device.
Uses
Hydraulic motors are used for many applications now such as winches and crane drives, wheel motors for military vehicles, self-driven cranes, and excavators. Conveyor and feeder drives, mixer and agitator drives, roll mills, drum drives for digesters, trommels and kilns, shredders for cars, tyres, cable and general garbage, drilling rigs, trench cutters, high-powered lawn trimmers, plastic injection machines