Jump to content

Fresnel integral

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Themulticaster (talk | contribs) at 00:15, 3 November 2016 (Euler spiral: Math markup cleanup). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

S(x) and C(x) The maximum of C(x) is about 0.977451424. If were used instead of , then the image would be scaled vertically and horizontally (see below).

Fresnel integrals, S(x) and C(x), are two transcendental functions named after Augustin-Jean Fresnel that are used in optics, which are closely related to the error function (erf). They arise in the description of near field Fresnel diffraction phenomena, and are defined through the following integral representations:

The simultaneous parametric plot of S(x) and C(x) is the Euler spiral (also known as the Cornu spiral or clothoid). Recently, they have been used in the design of highways and other engineering projects.[1]

Definition

The Fresnel integrals admit the following power series expansions that converge for all x:

Normalised Fresnel integrals, S(x) and C(x). In these curves, the argument of the trigonometric function is πt2/2, as opposed to just t2 as above.

Some authors, including Abramowitz and Stegun, (eqs 7.3.1 – 7.3.2) use for the argument of the integrals defining S(x) and C(x). To get these functions, multiply the above integrals by and multiply the argument x by .

Euler spiral

Euler spiral . The spiral converges to the centre of the holes in the image as tends to positive or negative infinity.

The Euler spiral, also known as Cornu spiral or clothoid, is the curve generated by a parametric plot of against . The Cornu spiral was created by Marie Alfred Cornu as a nomogram for diffraction computations in science and engineering.

From the definitions of Fresnel integrals, the infinitesimals and are thus:

Thus the length of the spiral measured from the origin can be expressed as:

That is, the parameter is the curve length measured from the origin and the Euler spiral has infinite length. The vector also expresses the unit tangent vector along the spiral, giving . Since t is the curve length, the curvature, can be expressed as:

And the rate of change of curvature with respect to the curve length is:

An Euler spiral has the property that its curvature at any point is proportional to the distance along the spiral, measured from the origin. This property makes it useful as a transition curve in highway and railway engineering.

If a vehicle follows the spiral at unit speed, the parameter in the above derivatives also represents the time. That is, a vehicle following the spiral at constant speed will have a constant rate of angular acceleration.

Sections from Euler spirals are commonly incorporated into the shape of roller-coaster loops to make what are known as "clothoid loops".

Properties

  • C(x) and S(x) are odd functions of x.
  • Asymptotics of the Fresnel integrals as are given by the formulas:
Complex Fresnel integral S(z)
Complex Fresnel integral C(z)
or

Limits as x approaches infinity

The integrals defining C(x) and S(x) cannot be evaluated in the closed form in terms of elementary functions, except in special cases. The limits of these functions as x goes to infinity are known:

The sector contour used to calculate the limits of the Fresnel integrals

The limits of C and S as the argument tends to infinity can be found by the methods of complex analysis. This uses the contour integral of the function

around the boundary of the sector-shaped region in the complex plane formed by the positive x-axis, the bisector of the first quadrant y = x with x ≥ 0, and a circular arc of radius R centered at the origin.

As R goes to infinity, the integral along the circular arc tends to 0, the integral along the real axis tends to the half Gaussian integral

Note too that because the integrand is an entire function on the complex plane, its integral along the whole contour is zero. Overall, we must have

where denotes the bisector of the first quadrant, as in the diagram. To evaluate the right hand side, parametrize the bisector as where r ranges from 0 to . Note that the square of this expression is just . Therefore, substitution gives the right hand side as

Using Euler's formula to take real and imaginary parts of gives this as

where we have written to emphasize that the original Gaussian integral's value is completely real with zero imaginary part. Letting and then equating real and imaginary parts produces the following system of two equations in the two unknowns :

Solving this for and gives the desired result.

Generalization

The integral

is a confluent hypergeometric function and also an incomplete Gamma function [3]

which reduces to Fresnel integrals if real or imaginary parts are taken:

.

The leading term in the asymptotic expansion is

and therefore

For m = 0, the imaginary part of this equation in particular is

with the left-hand side converging for a > 1 and the right-hand side being its analytical extension to the whole plane less where lie the poles of .

The Kummer transformation of the confluent hypergeometric function is

with

Applications

The Fresnel integrals were originally used in the calculation of the electromagnetic field intensity in an environment where light bends around opaque objects.[4] More recently, they have been used in the design of highways and railways, specifically their curvature transition zones, see track transition curve.[1] Another application is roller coasters.[4] Another application is for calculating the transitions on a velodrome track to allow rapid entry to the bends and gradual exit.[citation needed]

See also

References

  1. ^ a b Stewart, James (2007). Essential Calculus. Belmont, Calif.: Thomson Brooks/Cole. p. 230. ISBN 0-495-01442-7.
  2. ^ functions.wolfram.com, Fresnel integral S: Representations through equivalent functions and Fresnel integral C: Representations through equivalent functions. Note: Wolfram uses the Abramowitz & Stegun convention, which differs from the one in this article by factors of
  3. ^ Mathar, R. J. (2012). "Series Expansion of Generalized Fresnel Integrals". arXiv:1211.3963.
  4. ^ a b Beatty, Thomas. "How to evaluate Fresnel Integrals" (PDF). FGCU MATH - SUMMER 2013. Retrieved 27 July 2013.