Jump to content

BMC B-series engine

Edit links
From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Monkbot (talk | contribs) at 00:12, 4 January 2021 (Task 18 (cosmetic): eval 2 templates: hyphenate params (1×);). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

B-series engine
Overview
ManufacturerBMC
Production1954–1986
Layout
ConfigurationInline-4 and Inline-6
Displacement
  • I4s: 1.2 L (1,199.6 cc)
  • 1.5 L (1,490 cc)
  • 1.6 L (1,588 cc)
  • 1.6 L (1,623 cc)
  • 1.8 L (1,762 cc)
  • 1.8 L (1,798 cc)
  • I6: 2.4 L (2,433 cc)
Cylinder bore
  • 65.5 mm (2.6 in)
  • 73 mm (2.9 in)
  • 75.4 mm (3.0 in)
  • 76.2 mm (3.0 in)
  • 80.2 mm (3.2 in)
Piston stroke89 mm (3.5 in)
Cylinder block materialCast iron
Cylinder head material
ValvetrainOHV, Twin-Cam
Compression ratio8.3:1-9.9:1
Combustion
Fuel systemSingle or twin carburettors
Fuel typePetrol & Diesel versions
Cooling systemWater-cooled
Output
Power output39–108 bhp (29–81 kW)
Torque output64 lb⋅ft (87 N⋅m)
Chronology
PredecessorBMC A-Series engine
Successor

The BMC B series was a line of straight-4 internal combustion engine mostly used in motor cars, created by British company Austin Motor Company.

Design

A sectioned illustration of the Austin A40's 1200cc engine – the direct predecessor to the B series

The precursor of the "B" series engine was a 1200 cc Overhead Valve (OHV) engine which was used in the 1947-1952 Austin A40 Devon, and, in slightly modified form, in the 1953 Austin A40 Somerset. This engine had many of the same basic dimensions as one of Austin's pre-war sidevalve engines - the 1125cc engine fitted in the Austin 10 which had the 89mm (3.5in) stroke common to all later B-Series engines, allowing the use of much of the same installed equipment to produce the block and crankshaft - but to an all-new OHV design. Beyond this relationship to the pre-war Ten's engine, the lineage of the new OHV 1200cc power unit was somewhat complex - in the rest of its design it was in essence a scaled-down version of the 2199cc engine introduced in 1945 on the Austin 16 hp.

The design of this unit were derived from the much larger OHV engine developed for the wartime Austin K5 military truck, which used a 3995cc straight-six engine (minus two cylinders this engine became the 2660cc four-cylinder engine used in the Austin A90 Atlantic and the Austin-Healey 100). The K5 engine was broadly an Austin version of the 3519cc engine built by Bedford for its military trucks, and in turn the Bedford engine was similar in design to the Chevrolet 235 straight-six engine - Bedford and Chevrolet both being part of General Motors. The common features found on all these engines, from the Chevrolet 235 to the Austin 1200cc, include the design of the valve gear and the cylinder head, especially the siamesed cylinder head ports.

The A40 engine was originally drawn up to be produced in two capacities of 990cc and 1200cc to fall into the Eight and Ten tax horsepower classes. Before the A40 was launched, the British government removed the tax horsepower system in favour of a flat tax rate making the smaller capacity redundant. Therefore only the 1200cc version was built but could not be increased in capacity any further since it was already nearly at the maximum bore and stroke dimensions permitted by the design of the block casting.

Austin realised that eventually they would need an engine that could power many of its forthcoming medium-sized cars, and this would require an engine of at least 1500 cc capacity. Since the A40 Devon engine could not have its capacity enlarged, a new engine needed to be designed and built.

The design of this new engine commenced around January 1952, and was designated as the "B" series. The first production version of the B series retained the same 1200cc capacity as the A40 engine and, superficially, appeared to be identical, with the same valve gear, same cylinder head design, same positioning of its ancillary parts (many of which were interchangeable with the older engine) and so on. But the B-series block and head were slightly larger in both length and width and the block had thicker cylinder wall castings making the new engine heavier than the A40 motor. This was to allow room for enlargement of the cylinder bore to provide the larger capacities foreseen by BMC.

The stroke was retained at 89 mm (3.5 in) and was never altered. Originally of approximately 1.2 Litre capacity, later displacements ranged widely from 1.2 L to 2.4 L, the latter being an Australia only production six-cylinder variant. The most common engine sizes were 1.5 L and 1.8 L and saw service in a number of vehicles. This included a version of the engine built under license in India by Hindustan Motors for its Ambassador series of cars.[1] Petrol versions were produced in the greatest numbers, but diesel versions exist for both cars and marine applications.

Construction

The engine was of conventional construction with a one-piece crankcase and cylinder block in cast iron with the crankcase extending down to the lowest level of the main bearing caps; with a cylinder head, also usually in cast iron, and a sump made from pressed steel for rear-wheel drive vehicles. Early engines used a three-bearing crankshaft, but later engines used five bearings. On all except the rare twin overhead camshaft variant, the camshaft — which was chain driven and mounted low in the block — operated the overhead valves via pushrods and rocker arms. The two inlet ports in the non-crossflow cylinder head were shared between cylinders 1 + 2 and 3 + 4 and the three exhaust ports between cylinder 1, 2 + 3 and 4. Valve clearance was adjustable by screws and locknuts on the rocker arms.[2] Another unconventional characteristic of the engine is that the bore spacing is not constant between all four bores. The distance from cylinder 1 to 2 is 3.4375"; 2 to 3 =3.875" ;and 3 to 4 =3.4375".

The B series shares many design features (such as the heart-shaped combustion chambers and siamese inlet ports designed by Harry Weslake), as well as its basic layout and general appearance, with the smaller BMC A-series engine. However another difference was its block's full-depth skirt which provided excellent bottom-end strength. This made the engine highly durable and suitable for developing into diesel versions in later years.

Engine types

1.2 litre engines

The 1.2 L (1,199.6 cc) version was the first version of the engine. The bore and the stroke was 65.5 mm × 89 mm (2.58 in × 3.50 in). The maximum power output was 39 bhp (29 kW) at 4300 rpm.

After the formation of British Motor Corporation (BMC) the new B Series engine was used in the following vehicles:

1.5 litre engines

B-series 1500 engine in a Nash Metropolitan Series 3

The 1.5 L (1,489 cc) version was first used in 1953 in the MG Magnette ZA in twin carburettor version and in 1954 in the Morris Oxford series II and Austin Cambridge.[3] In 1957, it was used in the original MGA. Output in twin carburettor form was 68–72 bhp (51–54 kW) and 55 bhp (41 kW) with a single carburettor. Bore and stroke was 73 mm × 89 mm (2.9 in × 3.5 in).

There was also a diesel version of this engine size. Power output was 40 bhp (30 kW) at 4,000 rpm and torque 64 lb⋅ft (87 N⋅m) at 1,900 rpm. The 1.5–litre diesel engines were made in India by Hindustan Motors for many decades until the production of the legendary Ambassador was phased out in 2013. They are very popular amongst the taxicab market in India even today.

Applications:

Twin-Cam engines

A special Twin-Cam (DOHC) version of the 1.6 L (1,588 cc) B-series engine was produced for the MGA. Output was 108 bhp (81 kW) at 6700 rpm in the high-compression (9.9:1) version and 100 bhp (75 kW) in the optional low-compression (8.3:1) version. The engine block was cast iron, but the crossflow eight-port cylinder head was of aluminium alloy. Drive to the twin camshafts was by chain from a gear-driven, half-speed shaft running in the space that would have been occupied by the conventional camshaft.

This engine gained a reputation for being unreliable in service, especially in the high-compression version which needed high-octane fuel, but this has now been largely overcome. The piston burning habits — thought to be the result of ignition timing — was later discovered to be due to a vibration induced lean burn situation involving the float bowls, easily correctable by flexibly mounting the carburettors. A total of 2,111 cars were built, in both coupé and roadster versions.

A very few engines with the special displacement of 1.8 L (1,762 cc) were produced for racing purposes.

Applications:

1.6 litre engines

The engine was enlarged to 1.6 L (1,588 cc) in 1958 by increasing the bore to 75.4 mm (2.97 in).

Applications:

1.6 litre Mark II engines

The engine was enlarged to 1.6 L (1,622 cc) in 1961 with another bore increase, this time to 76.2 mm (3.00 in).

Applications:

The 1.6 L (1,622 cc) B series also formed the basis of the "Blue Streak" engine developed by BMC Australia for use in the locally-built Austin Freeway and Wolseley 24/80 models, both in turn variants of the existing Austin A60 Cambridge. The "Blue Streak" was an inline-6 development of the B series, adding two extra cylinders to create a 2.4 L (2,433 cc) engine. Different market demands in Australia required the fitting of a six-cylinder engine to a car the size of BMC's mid-range Farina model and the corporate C-series engine would not fit, requiring the development of the unique "Blue Streak" engine. Both models were withdrawn in 1965 and no further use of the engine was made.

1.8 litre engines

The engine was enlarged again to 1.8 L (1,798 cc) in 1962. Bore was 80.2 mm (3.16 in) and stroke was still 89 mm (3.5 in), power varied by application with typically 94 bhp (70 kW) @ 5500 rpm in twin carburettor format and 85 bhp (63 kW) in single carburettor format as used in the Morris Marina.[4] The engine at first had a three-bearing crankshaft with a five-bearing version appearing in 1964.

There was also a diesel version of this capacity, used in the Leyland Sherpa van with a power output of 56 bhp (42 kW) @ 4,250 rpm, and built under license in Turkey for many years. It is still widely used on narrowboats on the canals of the UK.[citation needed]

Applications:

2.4 litre engines

There was a 2.4 L (2,433 cc) six-cylinder unit, named "Blue Streak", which was used in the Australian Austin Freeway and Wolseley 24/80.

Engine numbering

There were two series of engine numbers used; BMC changed the system at the end of 1956.[5]

Numbering system, 1936 to 1956

As an example numbers were of the style "BP15GB" followed by the engines serial number, where:

  • BP = B series engine with P for pushrod (Overhead Valve)
  • 15 = capacity
  • G = MG (for full list of codes see reference below)
  • B = This final letter denotes the engine version.

Numbering system, 1957 to 1970

As an example numbers were of the style "15GB-U-H" plus a serial number, where:

  • 15 = capacity
  • G = MG (other letters were: A = Austin, B = Industrial, H = Miscellaneous, J = Commercial, M = Morris, R = Riley, V = Vanden Plas and W = Wolseley )
  • B = B series engine
  • U = Central gear change (other letters were: A = Automatic, M = Manumatic clutch, N = Column change, O = Overdrive, P = Police, DA = Close ratio gearbox. Note letter A is in a smaller font size).
  • H = High compression (alternatively L = Low compression)

Numbering system, 1970 onwards

Beginning in the early 1970s the numbering system was simplified to "18 V" plus a serial number, where 18 represents the capacity and V = vertical, i.e. longitudinal (in-line, not vee-arranged) engine with rear-wheel drive, and H = Horizontal, i.e. transverse engine with front-wheel drive.[5]

There was sometimes a country indicator after the first part of the code, e.g. "18V-Z" was use for some United States (except California) MG MGB engines.

See also

References

  1. ^ Hindustan Ambassador. (webpage) Retrieved on 2 January 2016 from http://www.uniquecarsandparts.com.au/car_info_hindustan_ambassador.php
  2. ^ Austin Motor Company. Austin A40 Models Service Manual. Austin, Birmingham, UK.
  3. ^ Lost Marques;Morris-The William Morris Story. (webpage) Retrieved on 1 January 2016 from http://www.uniquecarsandparts.com.au/lost_marques_morris.php
  4. ^ Zal, Pawel. "1972 Morris Marina Coupé". Automobile-Catalog.com. Retrieved 25 February 2017.
  5. ^ a b MG Car Club. Engine Codes (webpage) Accessed on 1 January 2016 from http://www.mg-cars.org.uk/news/news498.html
  • Porter, Lindsay (1985). BMC and Leyland B-Series Engine Data. Osprey. ISBN 0-85045-597-9.
Retrieved from "https://en.wikipedia.org/w/index.php?title=BMC_B-series_engine&oldid=998135041"