Jump to content

Bandgap voltage reference

From Wikipedia, the free encyclopedia
(Redirected from Band gap reference)

A bandgap voltage reference is a voltage reference circuit widely used in integrated circuits. It produces an almost constant voltage corresponding to the particular semiconductor's theoretical band gap, with very little fluctuations from variations of power supply, electrical load, time, temperature (as of 1999, they typically have an initial error of 0.5–1.0% and a temperature coefficient of 25–50 ppm/°C).[1]

David Hilbiber of Fairchild Semiconductor filed a patent in 1963[2] and published this circuit concept in 1964.[3] Bob Widlar,[4] Paul Brokaw[5] and others[6] followed up with other commercially-successful versions.

Operation

[edit]
Circuit of a Brokaw bandgap reference
Characteristic and balance point of T1 and T2

The voltage difference between two p–n junctions (e.g. diodes), operated at different current densities, is used to generate a current that is proportional to absolute temperature (PTAT) in a resistor. This current is used to generate a voltage in a second resistor. This voltage in turn is added to the voltage of one of the junctions (or a third one, in some implementations). The voltage across a diode operated at constant current is complementary to absolute temperature (CTAT), with a temperature coefficient of approximately −2 mV/K. If the ratio between the first and second resistor is chosen properly, the first order effects of the temperature dependency of the diode and the PTAT current will cancel out.

Although silicon's (Si) band gap at 0 K is technically 1.165 eV, the circuit essentially linearly extrapolates the bandgap–temperature curve[7] to determine a slightly higher but precise reference around 1.2–1.3 V (the specific value depends on the particular technology and circuit design); the remaining voltage change over the operating temperature of typical integrated circuits is on the order of a few millivolts. This temperature dependency has a typical parabolic residual behavior since the linear (first order) effects are chosen to cancel.

Because the output voltage is by definition fixed around 1.25 V for typical Si bandgap reference circuits, the minimum operating voltage is about 1.4 V, as in a CMOS circuit at least one drain-source voltage of a field-effect transistor (FET) has to be added. Therefore, recent work concentrates on finding alternative solutions, in which for example currents are summed instead of voltages, resulting in a lower theoretical limit for the operating voltage.[6]

The first letter of the acronym, CTAT, is sometimes misconstrued to represent constant rather than complementary. The term, constant with temperature (CWT), exists to address this confusion, but is not in widespread use.

When summing a PTAT and a CTAT current, only the linear terms of current are compensated, while the higher-order terms are limiting the temperature drift (TD) of the bandgap reference at around 20 ppm/°C, over a temperature range of 100 °C. For this reason, in 2001, Malcovati[8] designed a circuit topology that can compensate high-order non-linearities, thus achieving an improved TD. This design used an improved version of Banba's [6] topology and an analysis of base-emitter temperature effects that was performed by Tsividis in 1980.[9] In 2012, Andreou[10][11] has further improved the high-order non-linear compensation by using a second operational amplifier along with an additional resistor leg at the point where the two currents are summed up. This method enhanced further the curvature correction and achieved superior TD performance over a wider temperature range. In addition it achieved improved line regulation and lower noise.

The other critical issue in design of bandgap references is power efficiency and size of circuit. As a bandgap reference is generally based on BJT devices and resistors, the total size of circuit could be large and therefore expensive for IC design. Moreover, this type of circuit might consume a lot of power to reach to the desired noise and precision specification.[12]

Despite these limitations, the band gap voltage reference is widely used in voltage regulators, covering the majority of 78xx, 79xx devices along with the TL431 and the complementary LM317 and LM337. Temperature coefficients as low as 1.5–2.0 ppm/°C can be obtained with bandgap references.[a] However, the parabolic characteristic of voltage versus temperature means that a single figure in ppm/°C does not adequately describe the behavior of the circuit. Manufacturers' data sheets show that the temperature at which the peak (or trough) of the voltage curve occurs is subject to normal sample variations in production. Bandgap references are also suited for low-power applications.[b]

Mixed-signal microcontrollers may provide an internal bandgap reference signal to be used as reference for any internal comparator(s) and analog-to-digital converter(s).

Patents

[edit]
  • 1966, US Patent 3271660, Reference voltage source, David Hilbiber.[13]
  • 1971, US Patent 3617859, Electrical regulator apparatus including a zero temperature coefficient voltage reference circuit, Robert Dobkin and Robert Widlar.[14]
  • 1981, US Patent 4249122, Temperature compensated bandgap IC voltage references, Robert Widlar.[15]
  • 1984, US Patent 4447784, Temperature compensated bandgap voltage reference circuit, Robert Dobkin.[16]

Notes

[edit]
  1. ^ For example, LT6657 from Linear Technology and ADR4550 from Analog Devices.
  2. ^ For example, 1 μA cathode current with the Maxim Integrated MAX6009 shunt voltage reference.

See also

[edit]

References

[edit]
  1. ^ Miller, Perry; Moore, Doug (November 1999). "Precision voltage references" (PDF). Texas Instruments. Archived (PDF) from the original on 2023-05-17. Retrieved 2024-01-20.
  2. ^ US3271660A, Hilbiber, David F., "Reference voltage source", issued 1966-09-06 
  3. ^ Hilbiber, D.F. (1964). "A new semiconductor voltage standard". 1964 IEEE International Solid-State Circuits Conference. Digest of Technical Papers. 1964 International Solid-State Circuits Conference: Digest of Technical Papers. Vol. 2. pp. 32–33. doi:10.1109/ISSCC.1964.1157541.
  4. ^ Widlar, Robert J. (February 1971), "New Developments in IC Voltage Regulators", IEEE Journal of Solid-State Circuits, 6 (1): 2–7, Bibcode:1971IJSSC...6....2W, doi:10.1109/JSSC.1971.1050151, S2CID 14461709
  5. ^ Brokaw, Paul (December 1974), "A simple three-terminal IC bandgap reference", IEEE Journal of Solid-State Circuits, 9 (6): 388–393, Bibcode:1974IJSSC...9..388B, doi:10.1109/JSSC.1974.1050532, S2CID 12673906
  6. ^ a b c Banba, H.; Shiga, H.; Umezawa, A.; Miyaba, T.; Tanzawa, T.; Atsumi, S.; Sakui, K. (May 1999), "A CMOS bandgap reference circuit with sub-1-V operation", IEEE Journal of Solid-State Circuits, 34 (5): 670–674, Bibcode:1999IJSSC..34..670B, doi:10.1109/4.760378, S2CID 10495180
  7. ^ https://people.engr.tamu.edu/s-sanchez/607%20Lect%204%20Bandgap-2009.pdf slides 8-9 and https://users.wpi.edu/~mcneill/handouts/BandgapPrinciple.pdf graph this linear extrapolation
  8. ^ Malcovati, P.; Maloberti, F.; Fiocchi, C.; Pruzzi, M. (2001). "Curvature-compensated BiCMOS bandgap with 1-V supply voltage". IEEE Journal of Solid-State Circuits. 36 (7): 1076–1081. Bibcode:2001IJSSC..36.1076M. CiteSeerX 10.1.1.716.6243. doi:10.1109/4.933463. S2CID 7504312.
  9. ^ Y. P. Tsividis, "Accurate analysis of temperature effects in Ic-Vbe characteristics with application to bandgap reference sources," IEEE J. Solid-State Circuits, vol. 15, no. 6, pp. 1076 – 1084, Dec. 1980.
  10. ^ Andreou, Charalambos M.; Koudounas, Savvas; Georgiou, Julius (2012). "A Novel Wide-Temperature-Range, 3.9 PPM/°C CMOS Bandgap Reference Circuit". IEEE Journal of Solid-State Circuits. 47 (2): 574–581. doi:10.1109/JSSC.2011.2173267. S2CID 34901947.
  11. ^ Koudounas, Savvas; Andreou, Charalambos M.; Georgiou, Julius (2010). "A novel CMOS Bandgap reference circuit with improved high-order temperature compensation". Proceedings of 2010 IEEE International Symposium on Circuits and Systems. pp. 4073–4076. doi:10.1109/ISCAS.2010.5537621. ISBN 978-1-4244-5308-5. S2CID 30644500.
  12. ^ Tajalli, A.; Atarodi, M.; Khodaverdi, A.; Sahandi Esfanjani, F. (2004). "Design and optimization of a high PSRR CMOS bandgap voltage reference". 2004 IEEE International Symposium on Circuits and Systems (IEEE Cat. No.04CH37512). pp. I-45–I-48. doi:10.1109/ISCAS.2004.1328127. ISBN 0-7803-8251-X. S2CID 9650641.
  13. ^ US Patent 3271660 - Reference voltage source, David F Hilbiber; United States Patent and Trademark Office; September 6, 1966.
  14. ^ US Patent 3617859 - Electrical regulator apparatus including a zero temperature coefficient voltage reference circuit; Robert C Dobkin and Robert J Widlar; United States Patent and Trademark Office; November 2, 1971.
  15. ^ US Patent 4249122 - Temperature compensated bandgap IC voltage references; Robert J Widlar; United States Patent and Trademark Office; February 3, 1981.
  16. ^ US Patent 4447784 - Temperature compensated bandgap voltage reference circuit; Robert C Dobkin; United States Patent and Trademark Office; May 8, 1984.
[edit]
Retrieved from "https://en.wikipedia.org/w/index.php?title=Bandgap_voltage_reference&oldid=1242929550"