Electronic color code

RMA (Radio Manufacturers Association) Resistor Color Code Guide, c. 1945-1955.

The electronic color code is used to indicate the values or ratings of electronic components, very commonly for resistors, but also for capacitors, inductors, and others. A separate code, the 25-pair color code, is used to identify wires in some telecommunications cables.

The electronic color code was developed in the early 1920s by the Radio Manufacturers Association (now part of Electronic Industries Alliance (EIA)), and was published as EIA-RS-279. The current international standard is IEC 60062.

Colorbands were commonly used (especially on resistors) because they were easily printed on tiny components, decreasing construction costs. However, there were drawbacks, especially for color blind people. Overheating of a component, or dirt accumulation, may make it impossible to distinguish brown from red from orange. Advances in printing technology have made printed numbers practical for small components, which are often found in modern electronics.

Resistor color-coding

One decade of the E12 series (there are twelve preferred values per decade of values) shown with their electronic color codes on resistors

A 100 kΩ, 5% axial-lead resistor

A 0Ω resistor, marked with a single black band

A 2260 ohm, 1% precision resistor with 5 color bands (E96 series), from top 2-2-6-1-1; the last two brown bands indicate the multiplier (x10), and the 1% tolerance. The larger gap before the tolerance band is somewhat difficult to distinguish.

To distinguish left from right there is a gap between the C and D bands.

• band A is the first significant figure of component value (left side)
• band B is the second significant figure (Some precision resistors have a third significant figure, and thus five bands.)
• band C is the decimal multiplier
• band D if present, indicates tolerance of value in percent (no band means 20%)

For example, a resistor with bands of yellow, violet, red, and gold will have first digit 4 (yellow in table below), second digit 7 (violet), followed by 2 (red) zeros: 4,700 ohms. Gold signifies that the tolerance is ±5%, so the real resistance could lie anywhere between 4,465 and 4,935 ohms.

Resistors manufactured for military use may also include a fifth band which indicates component failure rate (reliability); refer to MIL-HDBK-199 for further details.

Tight tolerance resistors may have three bands for significant figures rather than two, or an additional band indicating temperature coefficient, in units of ppm/K.

All coded components will have at least two value bands and a multiplier; other bands are optional.

The standard color code per EN 60062:2005 is as follows:

Ring color			Significant figures	Multiplier		Tolerance		Temperature coefficient
Name	Code	RAL				Percent [%]	Letter	[ppm/K]	Letter
None	–	–	–	–		±20	M	–
Pink	PK	3015	–	×10−3	×0.001	–		–
Silver	SR	–	–	×10−2	×0.01	±10	K	–
Gold	GD	–	–	×10−1	×0.1	±5	J	–
Black	BK	9005	0	×100	×1	–		250	U
Brown	BN	8003	1	×101	×10	±1	F	100	S
Red	RD	3000	2	×102	×100	±2	G	50	R
Orange	OG	2003	3	×103	×1000	±0.05	W	15	P
Yellow	YE	1021	4	×104	×10000	±0.02	P	25	Q
Green	GN	6018	5	×105	×100000	±0.5	D	20	Z
Blue	BU	5015	6	×106	×1000000	±0.25	C	10	Z
Violet	VT	4005	7	×107	×10000000	±0.1	B	5	M
Gray	GY	7000	8	×108	×100000000	±0.01	L (A)	1	K
White	WH	1013	9	×109	×1000000000	–		–

Resistors use preferred numbers for their specific values, which are determined by their tolerance. These values repeat for every decade of magnitude: 6.8, 68, 680, and so forth. In the E24 series the values are related by the 24th root of 10, while E12 series are related by the 12th root of 10, and E6 series by the 6th root of 10. The tolerance of device values is arranged so that every value corresponds to a preferred number, within the required tolerance.

Zero ohm resistors are made as lengths of wire wrapped in a resistor-shaped body which can be substituted for another resistor value in automatic insertion equipment. They are marked with a single black band.

The 'body-end-dot' or 'body-tip-spot' system was used for radial-lead (and other cylindrical) composition resistors sometimes still found in very old equipment; the first band was given by the body color, the second band by the color of the end of the resistor, and the multiplier by a dot or band around the middle of the resistor. The other end of the resistor was colored gold or silver to give the tolerance, otherwise it was 20%.

Capacitor color-coding

Capacitors may be marked with 4 or more colored bands or dots. The colors encode the first and second most significant digits of the value, and the third color the decimal multiplier in picofarads. Additional bands have meanings which may vary from one type to another. Low-tolerance capacitors may begin with the first 3 (rather than 2) digits of the value. It is usually, but not always, possible to work out what scheme is used by the particular colors used. Cylindrical capacitors marked with bands may look like resistors.

Color		Significant digits	Multiplier	Capacitance tolerance	Characteristic	DC working voltage	Operating temperature	EIA/vibration
	Black	0	1	±20%	—	—	−55 °C to +70 °C	10 to 55 Hz
	Brown	1	10	±1%	B	100	—	—
	Red	2	100	±2%	C	—	−55 °C to +85 °C	—
	Orange	3	1000	—	D	300	—	—
	Yellow	4	10000	—	E	—	−55 °C to +125 °C	10 to 2000 Hz
	Green	5	100000	±0.5%	F	500	—	—
	Blue	6	1000000	—	—	—	−55 °C to +150 °C	—
	Violet	7	10000000	—	—	—	—	—
	Grey	8	—	—	—	—	—	—
	White	9	—	—	—	—	—	EIA
	Gold	—	—	±5%*	—	1000	—	—
	Silver	—	—	±10%	—	—	—	—

*or ±0.5 pF, whichever is greater.

Extra bands on ceramic capacitors will identify the voltage rating class and temperature coefficient characteristics. A broad black band was applied to some tubular paper capacitors to indicate the end that had the outer electrode; this allowed this end to be connected to chassis ground to provide some shielding against hum and noise pickup.

Polyester film and "gum drop" tantalum electrolytic capacitors are also color-coded to give the value, working voltage and tolerance.

Diode part number

The part number for diodes was sometimes also encoded as colored rings around the diode, using the same numerals as for other parts. The JEDEC "1N" prefix was assumed, and the balance of the part number was given by three or four rings.

Postage stamp capacitors and war standard coding

Capacitors of the rectangular 'postage stamp" form made for military use during World War II used American War Standard (AWS) or Joint Army Navy (JAN) coding in six dots stamped on the capacitor. An arrow on the top row of dots pointed to the right, indicating the reading order. From left to right the top dots were: either black, indicating JAN mica, or silver, indicating AWS paper; first significant digit; and second significant digit. The bottom three dots indicated temperature characteristic, tolerance, and decimal multiplier. The characteristic was black for ±1000 ppm/°C, brown for ±500, red for ±200, orange for ±100, yellow for −20 to +100 ppm/°C, and green for 0 to +70 ppm/°C. A similar six-dot code by EIA had the top row as first, second and third significant digits and the bottom row as voltage rating (in hundreds of volts; no color indicated 500 volts), tolerance, and multiplier. A three-dot EIA code was used for 500 volt 20% tolerance capacitors, and the dots signified first and second significant digits and the multiplier. Such capacitors were common in vacuum tube equipment and in surplus for a generation after the war but are unavailable now.

Postage-stamp mica capacitors marked with the EIA 3-dot and 6-dot color codes, giving capacitance value, tolerance, working voltage, and temperature characteristic. This style of capacitor was used in vacuum-tube equipment.

Mnemonics

Further information: List of electronic color code mnemonics

A useful mnemonic matches the first letter of the color code, by order of increasing magnitude. Here is one that includes tolerance codes gold, silver, and none:

• Bad beer rots our young guts but vodka goes well – get some now.

or

• B.B. ROY of Great Britain Has a Very Good Wife.

or

• Black Boys Rape Our Young Girls But Violet Gives Willingly.

The colors are sorted in the order of the visible light spectrum: red (2), orange (3), yellow (4), green (5), blue (6), violet (7). Black (0) has no energy, brown (1) has a little more, white (9) has everything and grey (8) is like white, but less intense.

Examples

Color-coded resistors

From top to bottom:

• Green-Blue-Black-Black-Brown
  • 560 ohms ± 1%
• Red-Red-Orange-Gold
  • 22,000 ohms ± 5%
• Yellow-Violet-Brown-Gold
  • 470 ohms ± 5%
• Blue-Gray-Black-Gold
  • 68 ohms ± 5%

The physical size of a resistor is indicative of the power it can dissipate, not of its resistance.

Printed numbers

0Ω and 27Ω (27×10⁰) surface-mount resistors.

Color-coding of this form is becoming rarer. In newer equipment, most passive components come in surface mount packages. Many of these packages are unlabeled, and those that are labeled normally use alphanumeric codes, not colors.

In one popular marking method, the manufacturer prints 3 digits on components: 2 value digits followed by the power of ten multiplier. Thus the value of a resistor marked 472 is 4,700 Ω, a capacitor marked 104 is 100 nF (10x10⁴ pF), and an inductor marked 475 is 4.7 H (4,700,000 µH). This can be confusing; a resistor marked 270 might seem to be a 270 Ω unit, when the value is actually 27 Ω (27×10⁰). A similar method is used to code precision surface mount resistors by using a 4-digit code which has 3 significant figures and a power of ten multiplier. Using the same example as above, 4701 would represent a 470x10¹=4700 Ω, 1% resistor. Another way is to use the "kilo-" or "mega-" prefixes in place of the decimal point:

1K2 = 1.2 kΩ = 1,200 Ω

M47 = 0.47 MΩ = 470,000 Ω

68R = 68 Ω

For some 1% resistors, a three-digit alphanumeric code is used, which is not obviously related to the value but can be derived from a table of 1% values. For instance, a resistor marked 68C is 499(68) × 100(C) = 49,900 Ω. In this case the value 499 is the 68th entry of the E96 series of preferred 1% values. The multiplier letters are as follows:

EIA E96 SMD alphanumeric code

Letter	Multiplier	Decimal
Z	10−3	0.001
Y or R	10−2	0.01
X or S	10−1	0.1
A	100	1
B or H	101	10
C	102	100
D	103	1000
E	104	10000
F	105	100000

SMT jumpers, marked "0" or "000", are sometimes called "Zero-ohm links" or "0-ohm resistors" although technically they are not resistors.

Transformer wiring color codes

Power transformers used in North American vacuum-tube equipment often were color-coded to identify the leads. Black was the primary connection, red secondary for the B+ (plate voltage), red with a yellow tracer was the center tap for the B+ full-wave rectifier winding, green or brown was the heater voltage for all tubes, yellow was the filament voltage for the rectifier tube (often a different voltage than other tube heaters). Two wires of each color were provided for each circuit, and phasing was not identified by the color code.

Audio transformers for vacuum tube equipment were coded blue for the finishing lead of the primary, red for the B+ lead of the primary, brown for a primary center tap, green for the finishing lead of the secondary, black for grid lead of the secondary, and yellow for a tapped secondary. Each lead had a different color since relative polarity or phase was more important for these transformers. Intermediate-frequency tuned transformers were coded blue and red for the primary and green and black for the secondary.

Other wiring codes

Wires may be color-coded to identify their function, voltage class, polarity, phase or to identify the circuit in which they are used. The insulation of the wire may be solidly colored, or where more combinations are needed, one or two tracer stripes may be added. Some wiring color codes are set by national regulations, but often a color code is specific to a manufacturer or industry.

Building wiring under the US National Electrical Code and the Canadian Electrical Code is identified by colors to show energized and neutral conductors, grounding conductors and to identify phases. Other color codes are used in the UK and other areas to identify building wiring or flexible cable wiring.

Thermocouple wires and extension cables are identified by color code for the type of thermocouple; interchanging thermocouples with unsuitable extension wires destroys the accuracy of the measurement.

Automotive wiring is color-coded but standards vary by manufacturer; differing SAE and DIN standards exist.

Modern personal computer peripheral cables and connectors are color-coded to simplify connection of speakers, microphones, mice, keyboards and other peripherals, usually according to the PC99 scheme.

A common convention for wiring systems in industrial buildings is; black jacket - AC less than 1000 volts, blue jacket - DC or communications, orange jacket - medium voltage 2300 or 4160 V, red jacket 13,800 volts or higher. Red-jacketed cable is also used for fire alarm wiring, but has a much different appearance, since it operates at relatively low voltages.

Local area network cables may also have jacket colors identifying, for example, process control network vs. office automation networks, or to identify redundant network connections, but these codes vary by organization and facility.

See also

• 25-pair color code — telecommunications wiring
• Color code (disambiguation)
• Electrical wiring — AC power wiring inside buildings, including standard color codes

External links

• IEC 60062 (IEC Webstore)

• 5-band Resistor Color Code Calculator
• Resistor color code calculator (Used to explore E-ranges and color codes.)
• Guide to SMD resistor codes, including alphanumeric codes