Magnetic mirror
![](http://upload.wikimedia.org/wikipedia/commons/thumb/9/9c/Basic_Magnetic_Mirror.jpg/220px-Basic_Magnetic_Mirror.jpg)
A magnetic mirror, known as a magnetic trap in Russia, is a type of magnetic confinement device used in fusion power to trap high temperature plasma using magnetic fields. The mirror was one of the earliest major approaches to fusion power, along with the stellarator and z-pinch machines.
In a magnetic mirror, a configuration of electromagnets is used to create an area with increasing density of magnetic field lines at either end of the confinement area. Particles approaching the ends experience an increasing force that eventually causes them to reverse direction and return to the confinement area.[1] This mirror effect will only occur for particles within a limited range of velocities and angles of approach, those outside the limits will escape, making mirrors inherently "leaky".
An analysis of early fusion devices by Edward Teller pointed out that the basic mirror concept is inherently unstable. In 1960, Soviet researchers introduced a new "minimum-B" configuration to address this, which was then modified by UK researchers into the "baseball coil" and by the US to "yin-yang magnet" layout. Each of these introductions led to further increases in performance, damping out various instabilities, but required ever-large magnet systems. The tandem mirror concept, developed in the US and Russia at about the same time, offered a way to make energy-positive machines without requiring enormous magnets and power input.
By the late 1970s, many of the design problems were considered solved, and Lawrence Livermore Laboratory began the design of the Mirror Fusion Test Facility (MFTF) based on these concepts. The machine was completed in 1986, but by this time, experiments on the smaller Tandem Mirror Experiment revealed new problems. In a round of budget cuts, MFTF was mothballed, and eventually scrapped. The mirror approach has since seen less development, in favor of the tokamak, but mirror research continues today in countries like Japan and Russia.[2]
History
![](http://upload.wikimedia.org/wikipedia/commons/thumb/3/3b/The_Tandem_Mirror_Experiment.jpg/220px-The_Tandem_Mirror_Experiment.jpg)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/c/ce/A_picture_of_the_2XII_Magnetic_Bottle.jpg/220px-A_picture_of_the_2XII_Magnetic_Bottle.jpg)
The concept of magnetic-mirror plasma confinement was proposed in the mid-1950s independently by Gersh Budker[3] at the Kurchatov Institute, Russia and Richard F. Post[4] at the Lawrence Livermore National Laboratory in the US.
With the formation of Project Sherwood in 1951, Post began development of a small device to test the mirror configuration. This consisted of a linear pyrex tube with magnets around the outside. The magnets were arranged in two sets, one set of small magnets spaced evenly along the length of the tube, and another pair of much larger magnets at either end. In 1952 they were able to demonstrate that plasma within the tube was confined for much longer times when the mirror magnets at the end were turned on.
In a now-famous talk on fusion in 1954, Edward Teller noted that any device with convex magnetic field lines would likely be unstable, a problem today known as the flute instability. The mirror has precisely such a configuration, but continued experiments seemed to suggest that the experimental machines were not suffering from this problem, although there were many more practical issues limiting their performance.
In Russia, the first small-scale mirror ("probkotron") was built in 1959 at the Budker Institute of Nuclear Physics in Novosibirsk, Russia. They immediately saw the problem Teller had warned them about. To fix the problem, the magnetic fields should ideally be concave. This was solved by M.S. Ioffe, who added a series of additional current-carrying bars inside the reactor, such that the resulting magnetic field took on the shape of a twisted bow-tie, known as the minimum-B configuration. They demonstrated that this greatly improved the confinement times to the order of milliseconds.
The mystery of why the US's simple mirrors were not seeing this problem was discovered at a meeting in 1961. Les Artsimovich inquired how the US team had concluded they had stable plasmas lasting on the order of milliseconds. This turned out to be due to the readings of one diagnostic instrument. When Artsimovich learned they had not accounted for the measurement delay in these instruments, it became clear the US mirrors had been suffering from this problem all along. With this discovery, "Ioffe bars" were quickly taken up by researchers in the US, UK, and Japan.
Tennisball/baseball coils
A group at the Culham Centre for Fusion Energy noted that the arrangement could be improved by combining the original rings and the bars into a single new arrangement similar to the seam on a tennis ball. This concept was picked up in the US where it was renamed after the stitching on a baseball. These "baseball coils" had the great advantage that they left the internal volume of the reactor open, allowing easy access for diagnostic instruments. On the downside, the size of the magnet in comparison to the volume of plasma was inconvenient, and required very powerful magnets. Post later introduced a further improvement, the "yin-yang coils", which used two C-shaped magnets to produce the same field configuration, but in a smaller volume.
With the major instability addressed, researchers now discovered that the original leakiness of the design was also far higher than expected. This was traced to a host of newly discovered "microinstabilities" that caused fuel to enter the "escape cone" of the reactor and flow out the ends of the mirror. Suppressing these new problems filled much of the 1960s,
By the late 1960s, magnetic mirror confinement was considered a viable technique for producing fusion energy. In the United States, efforts were initially funded under the United States Atomic Energy Commissions' Project Sherwood. A machine design was first published in 1967.[5] The concept was advocated by Richard F. Post, Kenneth Fowler, Fred Coensgen and many others at the Lawrence Livermore National Laboratory.[6] As a result of advocacy, the cold war, and the 1970s energy crisis a massive magnetic mirror program was funded by the U.S. federal government.
This program resulted in a series of large magnetic mirror devices including: 2X,[7] Baseball I, Baseball II.
However, theoretical calculations showed that the maximum amount of energy they could produce would be about the same as the energy needed to run the magnets.[citation needed] As a power-producing machine, the mirror appeared to be a dead end.
Tandem mirrors
In the 1970s, a solution was developed. By placing a baseball coil at either end of a large solenoid, the entire assembly could hold a much larger volume of plasma, and thus produce more energy. Plans began to build a large device of this "tandem mirror" design, which became the Mirror Fusion Test Facility (MFTF). Having never tried this layout before, a smaller machine, the Tandem Mirror Experiment (TMX) was built to test this layout.[8] TMX demonstrated a new series of problems that suggested MFTF would not reach its performance goals,[9] and during construction MFTF was modified to MFTF-B. TMX itself was also upgraded, to TMX-U.
These machines were built and tested at Livermore from the late 60's to the mid 80's.[10] A number of institutions collaborated on these machines, conducting experiments. These included the Institute for Advanced Study and the University of Wisconsin–Madison.[11][12]
The last machine, the Mirror Fusion Test Facility was 372 million dollars, at that time, the most expensive project in Livermore history. It opened on February 21, 1986 and was promptly shut down. The reason given was to balance the United States federal budget.[10] This program was supported from within the Carter and early Reagan administrations by Edwin E. Kintner, a U.S. Navy captain, under Alvin Trivelpiece. Kintner resigned in 1982 complaining that the federal government had not provided the resources needed for the research.[13]
After 1986
Magnetic mirror research continued in Russia, one modern example is the Gas Dynamic Trap, an experimental fusion machine used at the Budker Institute of Nuclear Physics in Akademgorodok, Russia. This machine has achieved a 0.6 beta ratio for 5E-3 seconds, at a low temperature of 1 KeV.
The concept had a number of technical challenges including maintaining the non-Maxwellian velocity distribution. This meant that instead of many high energy ions hitting one another, the ion energy spread out into a bell curve. The ions then thermalized, leaving most of the material too cold to fuse. Collisions also scattered the charged particles so much that they could not be contained. Lastly, velocity space instabilities contributed to the escape of the plasma.
Magnetic mirrors play an important role in other types of magnetic fusion energy devices such as tokamaks, where the toroidal magnetic field is stronger on the inboard side than on the outboard side. The resulting effects are known as neoclassical. Magnetic mirrors also occur in nature. Electrons and ions in the magnetosphere, for example, will bounce back and forth between the stronger fields at the poles, leading to the Van Allen radiation belts.
Mathematical derivation
The mirror effect can be shown mathematically. Assume adiabatic invariance of the magnetic moment, i.e. that the particle's magnetic moment and total energy do not change.[14] Adiabatic invariance is lost when a particle occupies a null point or zone of no magnetic field.[15] The magnetic moment can be expressed as:
It is assumed that μ will remain constant while the particle moves into the denser magnetic field. Mathematically, for this to happen the velocity perpendicular to the magnetic field must also rise. Meanwhile the total energy of the particle can be expressed as:
In regions with no electric field, if the total energy remains constant then the velocity parallel to the magnetic field must drop. If it can go negative then there is a motion repelling the particle from the dense fields.
Mirror ratios
Magnetic mirrors themselves have a mirror ratio this is expressed mathematically as:[16]
At the same time, particles within the mirror have a pitch angle. This is the angle between the particles' velocity vector and the magnetic field vector.[17] Surprisingly, the particles with the small pitch angle can escape the mirror.[18] These particles are said to be in the loss cone. The reflected particles meet the following criteria:[19]
Where is the particle velocity perpendicular to the magnetic field and is the particle speed.
This result was surprising because it was expected that heavier and faster particles, or those with less electric charge, would be harder to reflect. It was also expected that smaller magnetic field would reflect less particles. However, the gyroradius in those circumstances is also larger, so that the radial component of the magnetic field seen by the particle is also larger. It is true that the minimum volume and magnetic energy is larger for the case of fast particles and weak fields, but the mirror ratio required remains the same.
Adiabatic invariance
The properties of magnetic mirrors can be derived using the adiabatic invariance of magnetic flux under changes in magnetic field strength. As the field gets stronger, the velocity increases proportionally to the square root of B, and the kinetic energy is proportional to B. This can be thought of as an effective potential binding the particle.
Magnetic bottles
![](http://upload.wikimedia.org/wikipedia/commons/thumb/1/1e/Fields_in_magnetic_bottles.jpg/220px-Fields_in_magnetic_bottles.jpg)
A magnetic bottle is two magnetic mirrors placed close together. For example, two parallel coils separated by a small distance, carrying the same current in the same direction will produce a magnetic bottle between them. Unlike the full mirror machine which typically had many large rings of current surrounding the middle of the magnetic field, the bottle typically has just two rings of current. Particles near either end of the bottle experience a magnetic force towards the center of the region; particles with appropriate speeds spiral repeatedly from one end of the region to the other and back. Magnetic bottles can be used to temporarily trap charged particles. It is easier to trap electrons than ions, because electrons are so much lighter[20] This technique is used to confine the high energy of plasma in fusion experiments.
In a similar way, the Earth's non-uniform magnetic field traps charged particles coming from the sun in doughnut shaped regions around the earth called the Van Allen radiation belts, which were discovered in 1958 using data obtained by instruments aboard the Explorer 1 satellite.
Biconic cusps
![](http://upload.wikimedia.org/wikipedia/commons/thumb/7/7d/Biconic_Cusp.jpg/220px-Biconic_Cusp.jpg)
If one of the poles in the magnetic bottle is reversed, it becomes a biconic cusp, which can also hold charged particles.[21][22][23] Biconic cusps were first studied by Harold Grad at the Courant Institute, studies reveal the presence of different types of particles inside a biconic cusp.
See also
References
- ^ Fitzpatrick, Richard. "Magnetic Mirrors." Home Page for Richard Fitzpatrick. The University of Texas at Austin, 31 Mar. 2011. Web. 19 July 2011.
- ^ T.C. Simonen, Three game changing discoveries: a simpler fusion concept? J. Fusion Energ., February 2016, Volume 35, Issue 1, pp 63-68. doi:10.1007/s10894-015-0017-2
- ^ In Russian: Г.И. Будкер, Физика плазмы и проблема управляемых термоядерных реакций, Т. 3, Изд. АН СССР, Москва (1958), стр. 3-31; in English: G. I. Budker, Plasma Physics and the Problem of Controlled Thermonuclear Reactions, Vol. 3, Pergamon Press, New York (1959), pp. 1-33
- ^ R. F. Post, Proc. of Second U.N. Int. Conf. on Peaceful Uses of Atomic Energy, Vol. 32, Paper A/Conf. 15/P/377, Geneva (1958), pp. 245-265
- ^ G. G. Kelley, Plasma Phys. 2, 503 (1967)
- ^ "Mirror Systems: Fuel Cycles, loss reduction and energy recovery" by Richard F. Post, BNES Nuclear fusion reactor conferences at Culham laboratory, September 1969.
- ^ Principals of plasma physics, Nicholas Krall, 1973, Page 273
- ^ "TMX Major Project proposal" Fred Coensgen, January 12, 1977
- ^ "Summary of results from the tandem mirror experiment, TMX group, February 26, 1981
- ^ a b Booth, William. "Fusion's $372-Million Mothball." Science [New York City] 9 Oct. 1987, Volume 238 ed.: 152-55. Print.
- ^ "ion losses from end-stoppered mirror trap" D P Chernnin, nuclear fusion 18 (1978)
- ^ "Experiments in a tandem mirror sustained and heated solely by rf" R Breun, Physical Review Letters, December 21, 1981
- ^ KOPPEL, NIKO. "Edwin E. Kintner, Nuclear Power Pioneer, Dies at 90." The New York Times, Science Section. The New York Times, 20 May 2010. Web. 17 Apr. 2011. <https://www.nytimes.com/2010/05/21/science/21kintner.html?_r=1>
- ^ F. Chen, Introduction to Plasma Physics and Controlled Fusion (Plenum, New York, 1984), Vol. 1, pp. 30–34. ISBN 978-0-306-41332-2
- ^ TG Northrop, "The Adiabatic Motion of Charged Particles" (Interscience, New York, 1963)
- ^ "Particle Loss Rates from Electrostatic Wells of Arbitrary Mirror Ratios." Physics of Fluids 28.1 (1985): 352-57. Web. 15.
- ^ Dolan, T. J. "Magnetic Electrostatic Plasma Confinement." Plasma Physics and Controlled Fusion 36 (1994): 1539-593. Print.
- ^ G Gibson, Willard C Jordan, Eugene Lauer, Physical Review Letters, 5: 141 (1960)
- ^ Principals of Plasma Physics, N Krall, 1973, Page 267
- ^ "A biased probe analysis of potential well formation in an electron only, low beta Polywell magnetic field" Physics of Plasma, May 9, 2013, Vol 20, 052504
- ^ The motion of a charged particle near a zero field point (in english). New York: New York University: Courant Institute of Mathematical Sciences,. 1961.
- ^ Grad, H. Theory of Cusped Geometries, I. General Survey, NYO-7969, Inst. Math. Sci., N.Y.U., December 1, 1957
- ^ Berowitz, H Grad and H Rubin, in proceedings of the second United Nations International conference on peaceful uses of atomic energy, Geneva, 1958, Vol 31, Page 177