# Scattering parameters

(Redirected from S parameters)
Jump to navigation Jump to search

Scattering parameters or S-parameters (the elements of a scattering matrix or S-matrix) describe the electrical behavior of linear electrical networks when undergoing various steady state stimuli by electrical signals.

The parameters are useful for several branches of electrical engineering, including electronics, communication systems design, and especially for microwave engineering.

The S-parameters are members of a family of similar parameters, other examples being: Y-parameters,[1] Z-parameters,[2] H-parameters, T-parameters or ABCD-parameters.[3][4] They differ from these, in the sense that S-parameters do not use open or short circuit conditions to characterize a linear electrical network; instead, matched loads are used. These terminations are much easier to use at high signal frequencies than open-circuit and short-circuit terminations. Moreover, the quantities are measured in terms of power.

Many electrical properties of networks of components (inductors, capacitors, resistors) may be expressed using S-parameters, such as gain, return loss, voltage standing wave ratio (VSWR), reflection coefficient and amplifier stability. The term 'scattering' is more common to optical engineering than RF engineering, referring to the effect observed when a plane electromagnetic wave is incident on an obstruction or passes across dissimilar dielectric media. In the context of S-parameters, scattering refers to the way in which the traveling currents and voltages in a transmission line are affected when they meet a discontinuity caused by the insertion of a network into the transmission line. This is equivalent to the wave meeting an impedance differing from the line's characteristic impedance.

Although applicable at any frequency, S-parameters are mostly used for networks operating at radio frequency (RF) and microwave frequencies where signal power and energy considerations are more easily quantified than currents and voltages. S-parameters change with the measurement frequency, so frequency must be specified for any S-parameter measurements stated, in addition to the characteristic impedance or system impedance.

S-parameters are readily represented in matrix form and obey the rules of matrix algebra.

## Background

The first published description of S-parameters was in the thesis of Vitold Belevitch in 1945.[5] The name used by Belevitch was repartition matrix and limited consideration to lumped-element networks. The term scattering matrix was used by physicist and engineer Robert Henry Dicke in 1947 who independently developed the idea during wartime work on radar.[6][7] The technique was popularized in the 1960s by Kaneyuki Kurokawa[8]

In the S-parameter approach, an electrical network is regarded as a 'black box' containing various interconnected basic electrical circuit components or lumped elements such as resistors, capacitors, inductors and transistors, which interacts with other circuits through ports. The network is characterized by a square matrix of complex numbers called its S-parameter matrix, which can be used to calculate its response to signals applied to the ports.

For the S-parameter definition, it is understood that a network may contain any components provided that the entire network behaves linearly with incident small signals. It may also include many typical communication system components or 'blocks' such as amplifiers, attenuators, filters, couplers and equalizers provided they are also operating under linear and defined conditions.

An electrical network to be described by S-parameters may have any number of ports. Ports are the points at which electrical signals either enter or exit the network. Ports are usually pairs of terminals with the requirement that the current into one terminal is equal to the current leaving the other.[9][10] S-parameters are used at frequencies where the ports are often coaxial or waveguide connections.

The S-parameter matrix describing an N-port network will be square of dimension N and will therefore contain ${\displaystyle N^{2}\,}$ elements. At the test frequency each element or S-parameter is represented by a unitless complex number that represents magnitude and angle, i.e. amplitude and phase. The complex number may either be expressed in rectangular form or, more commonly, in polar form. The S-parameter magnitude may be expressed in linear form or logarithmic form. When expressed in logarithmic form, magnitude has the "dimensionless unit" of decibels. The S-parameter angle is most frequently expressed in degrees but occasionally in radians. Any S-parameter may be displayed graphically on a polar diagram by a dot for one frequency or a locus for a range of frequencies. If it applies to one port only (being of the form ${\displaystyle S_{nn}\,}$), it may be displayed on an impedance or admittance Smith Chart normalised to the system impedance. The Smith Chart allows simple conversion between the ${\displaystyle S_{nn}\,}$ parameter, equivalent to the voltage reflection coefficient and the associated (normalised) impedance (or admittance) 'seen' at that port.

The following information must be defined when specifying a set of S-parameters:

1. The frequency
2. The nominal characteristic impedance (often 50 Ω)
3. The allocation of port numbers
4. Conditions which may affect the network, such as temperature, control voltage, and bias current, where applicable.

## The general S-parameter matrix

### Definition

For a generic multi-port network, the ports are numbered from 1 to N, where N is the total number of ports. For port i, the associated S-parameter definition is in terms of incident and reflected 'power waves', ${\displaystyle a_{i}\,}$ and ${\displaystyle b_{i}\,}$ respectively.

Kurokawa[11] defines the incident power wave for each port as

${\displaystyle a_{i}={\frac {1}{2}}\,k_{i}(V_{i}+Z_{i}I_{i})\,}$

and the reflected wave for each port is defined as

${\displaystyle b_{i}={\frac {1}{2}}\,k_{i}(V_{i}-Z_{i}^{*}I_{i})\,}$

where ${\displaystyle Z_{i}\,}$ is the impedance for port i, ${\displaystyle Z_{i}^{*}\,}$ is the complex conjugate of ${\displaystyle Z_{i}\,}$, ${\displaystyle V_{i}\,}$ and ${\displaystyle I_{i}\,}$ are respectively the complex amplitudes of the voltage and current at port i, and

${\displaystyle k_{i}=\left({\sqrt {\left|\Re \{Z_{i}\}\right|}}\right)^{-1}\,}$

Sometimes it is useful to assume that the reference impedance is the same for all ports in which case the definitions of the incident and reflected waves may be simplified to

${\displaystyle a_{i}={\frac {1}{2}}\,{\frac {(V_{i}+Z_{0}I_{i})}{\sqrt {\left|\Re \{Z_{0}\}\right|}}}\,}$

and

${\displaystyle b_{i}={\frac {1}{2}}\,{\frac {(V_{i}-Z_{0}^{*}I_{i})}{\sqrt {\left|\Re \{Z_{0}\}\right|}}}\,}$

The relation between the vectors a and b, whose i-th components are the power waves ${\displaystyle a_{i}}$ and ${\displaystyle b_{i}}$ respectively, can be expressed using the S-parameter matrix S:

${\displaystyle \mathbf {b} =\mathbf {S} \cdot \mathbf {a} \,}$

Or using explicit components:

${\displaystyle {\begin{pmatrix}b_{1}\\\vdots \\b_{n}\end{pmatrix}}={\begin{pmatrix}S_{11}&\dots &S_{1n}\\\vdots &\ddots &\vdots \\S_{n1}&\dots &S_{nn}\end{pmatrix}}\cdot {\begin{pmatrix}a_{1}\\\vdots \\a_{n}\end{pmatrix}}}$

### Reciprocity

A network will be reciprocal if it is passive and it contains only reciprocal materials that influence the transmitted signal. For example, attenuators, cables, splitters and combiners are all reciprocal networks and ${\displaystyle S_{mn}=S_{nm}\,}$ in each case, or the S-parameter matrix will be equal to its transpose. Networks which include non-reciprocal materials in the transmission medium such as those containing magnetically biased ferrite components will be non-reciprocal. An amplifier is another example of a non-reciprocal network.

A property of 3-port networks, however, is that they cannot be simultaneously reciprocal, loss-free, and perfectly matched.[12]

### Lossless networks

A lossless network is one which does not dissipate any power, or: ${\displaystyle \Sigma \left|a_{n}\right|^{2}=\Sigma \left|b_{n}\right|^{2}\,}$. The sum of the incident powers at all ports is equal to the sum of the reflected powers at all ports. This implies that the S-parameter matrix is unitary, that is ${\displaystyle (S)^{H}(S)=(I)\,}$, where ${\displaystyle (S)^{H}\,}$ is the conjugate transpose of ${\displaystyle (S)\,}$ and ${\displaystyle (I)\,}$ is the identity matrix.

### Lossy networks

A lossy passive network is one in which the sum of the incident powers at all ports is greater than the sum of the reflected powers at all ports. It therefore dissipates power: ${\displaystyle \Sigma \left|a_{n}\right|^{2}\neq \Sigma \left|b_{n}\right|^{2}\,}$. Thus ${\displaystyle \Sigma \left|a_{n}\right|^{2}>\Sigma \left|b_{n}\right|^{2}\,}$, and ${\displaystyle (I)-(S)^{H}(S)\,}$ is positive definite.[13]

## Two-Port S-Parameters

The S-parameter matrix for the 2-port network is probably the most commonly used and serves as the basic building block for generating the higher order matrices for larger networks.[14] In this case the relationship between the reflected, incident power waves and the S-parameter matrix is given by:

${\displaystyle {\begin{pmatrix}b_{1}\\b_{2}\end{pmatrix}}={\begin{pmatrix}S_{11}&S_{12}\\S_{21}&S_{22}\end{pmatrix}}{\begin{pmatrix}a_{1}\\a_{2}\end{pmatrix}}\,}$.

Expanding the matrices into equations gives:

${\displaystyle b_{1}=S_{11}a_{1}+S_{12}a_{2}\,}$

and

${\displaystyle b_{2}=S_{21}a_{1}+S_{22}a_{2}\,}$.

Each equation gives the relationship between the reflected and incident power waves at each of the network ports, 1 and 2, in terms of the network's individual S-parameters, ${\displaystyle S_{11}\,}$, ${\displaystyle S_{12}\,}$, ${\displaystyle S_{21}\,}$ and ${\displaystyle S_{22}\,}$. If one considers an incident power wave at port 1 (${\displaystyle a_{1}\,}$) there may result from it waves exiting from either port 1 itself (${\displaystyle b_{1}\,}$) or port 2 (${\displaystyle b_{2}\,}$). However, if, according to the definition of S-parameters, port 2 is terminated in a load identical to the system impedance (${\displaystyle Z_{0}\,}$) then, by the maximum power transfer theorem, ${\displaystyle b_{2}\,}$ will be totally absorbed making ${\displaystyle a_{2}\,}$ equal to zero. Therefore, defining the incident voltage waves as ${\displaystyle a_{1}=V_{1}^{+}}$ and ${\displaystyle a_{2}=V_{2}^{+}}$ with the reflected waves being ${\displaystyle b_{1}=V_{1}^{-}}$ and ${\displaystyle b_{2}=V_{2}^{-}}$,

${\displaystyle S_{11}={\frac {b_{1}}{a_{1}}}={\frac {V_{1}^{-}}{V_{1}^{+}}}}$ and ${\displaystyle S_{21}={\frac {b_{2}}{a_{1}}}={\frac {V_{2}^{-}}{V_{1}^{+}}}\,}$.

Similarly, if port 1 is terminated in the system impedance then ${\displaystyle a_{1}\,}$ becomes zero, giving

${\displaystyle S_{12}={\frac {b_{1}}{a_{2}}}={\frac {V_{1}^{-}}{V_{2}^{+}}}\,}$ and ${\displaystyle S_{22}={\frac {b_{2}}{a_{2}}}={\frac {V_{2}^{-}}{V_{2}^{+}}}\,}$

The 2-port S-parameters have the following generic descriptions:

${\displaystyle S_{11}\,}$ is the input port voltage reflection coefficient
${\displaystyle S_{12}\,}$ is the reverse voltage gain
${\displaystyle S_{21}\,}$ is the forward voltage gain
${\displaystyle S_{22}\,}$ is the output port voltage reflection coefficient.

If, instead of defining the voltage wave direction relative to each port, they are defined by their absolute direction as forward ${\displaystyle V^{+}}$ and reverse ${\displaystyle V^{-}}$ waves then ${\displaystyle b_{2}=V_{2}^{+}}$ and ${\displaystyle a_{2}=V_{2}^{-}}$. The S-parameters then take on a more intuitive meaning such as the forward voltage gain being defined by the ratio of the forward voltages ${\displaystyle S_{21}=V_{2}^{+}/V_{1}^{+}}$.

## S-Parameter properties of 2-port networks

An amplifier operating under linear (small signal) conditions is a good example of a non-reciprocal network and a matched attenuator is an example of a reciprocal network. In the following cases we will assume that the input and output connections are to ports 1 and 2 respectively which is the most common convention. The nominal system impedance, frequency and any other factors which may influence the device, such as temperature, must also be specified.

### Complex linear gain

The complex linear gain G is given by

${\displaystyle G=S_{21}={\frac {b_{2}}{a_{1}}}\,}$.

That is the linear ratio of the output reflected power wave divided by the input incident power wave, all values expressed as complex quantities. For lossy networks it is sub-unitary, for active networks ${\displaystyle |G|>1}$ . It will be equal with the voltage gain only when the device has equal input and output impedances.

### Scalar linear gain

The scalar linear gain (or linear gain magnitude) is given by

${\displaystyle \left|G\right|=\left|S_{21}\right|\,}$.

This represents the gain magnitude (absolute value), the ratio of the output power-wave to the input power-wave, and it equals the square-root of the power gain. This is a real-value (or scalar) quantity, the phase information being dropped.

### Scalar logarithmic gain

The scalar logarithmic (decibel or dB) expression for gain (g) is:

${\displaystyle g=20\log _{10}\left|S_{21}\right|\,}$ dB.

This is more commonly used than scalar linear gain and a positive quantity is normally understood as simply a "gain", while a negative quantity is a "negative gain" (a "loss"), equivalent to its magnitude in dB. For example, at 100 MHz, a 10 m length of cable may have a gain of -1 dB, equal to a loss of 1 dB.

### Insertion loss

In case the two measurement ports use the same reference impedance, the insertion loss (IL) is the magnitude of the transmission coefficient |S21| expressed in decibels. It is thus given by:[15]

${\displaystyle IL=-20\log _{10}\left|S_{21}\right|\,}$ dB.

It is the extra loss produced by the introduction of the device under test (DUT) between the 2 reference planes of the measurement. Notice that the extra loss can be introduced by intrinsic loss in the DUT and/or mismatch. In case of extra loss the insertion loss is defined to be positive. The negative of insertion loss expressed in decibels is defined as insertion gain.

### Input return loss

Input return loss (RLin) can be thought of as a measure of how close the actual input impedance of the network is to the nominal system impedance value. Input return loss expressed in decibels is given by

${\displaystyle RL_{\mathrm {in} }=10\log _{10}\left|{\frac {1}{S_{11}^{2}}}\right|=-20\log _{10}\left|S_{11}\right|\,}$ dB.

Note that for passive two-port networks in which |S11| ≤ 1, it follows that return loss is a non-negative quantity: RLin ≥ 0. Also note that somewhat confusingly, return loss is sometimes used as the negative of the quantity defined above, but this usage is, strictly speaking, incorrect based on the definition of loss.[16]

### Output return loss

The output return loss (RLout) has a similar definition to the input return loss but applies to the output port (port 2) instead of the input port. It is given by

${\displaystyle RL_{\mathrm {out} }=-20\log _{10}\left|S_{22}\right|\,}$ dB.

### Reverse gain and reverse isolation

The scalar logarithmic (decibel or dB) expression for reverse gain (${\displaystyle g_{\mathrm {rev} }\,}$) is:

${\displaystyle g_{\mathrm {rev} }=20\log _{10}\left|S_{12}\right|\,}$ dB.

Often this will be expressed as reverse isolation (${\displaystyle I_{\mathrm {rev} }\,}$) in which case it becomes a positive quantity equal to the magnitude of ${\displaystyle g_{\mathrm {rev} }\,}$ and the expression becomes:

${\displaystyle I_{\mathrm {rev} }=\left|g_{\mathrm {rev} }\right|=\left|20\log _{10}\left|S_{12}\right|\right|\,}$ dB.

### Reflection coefficient

The reflection coefficient at the input port (${\displaystyle \Gamma _{\mathrm {in} }\,}$) or at the output port (${\displaystyle \Gamma _{\mathrm {out} }\,}$) are equivalent to ${\displaystyle S_{11}\,}$ and ${\displaystyle S_{22}\,}$ respectively, so

${\displaystyle \Gamma _{\mathrm {in} }=S_{11}\,}$ and ${\displaystyle \Gamma _{\mathrm {out} }=S_{22}\,}$.

As ${\displaystyle S_{11}\,}$ and ${\displaystyle S_{22}\,}$ are complex quantities, so are ${\displaystyle \Gamma _{\mathrm {in} }\,}$ and ${\displaystyle \Gamma _{\mathrm {out} }\,}$.

The reflection coefficients are complex quantities and may be graphically represented on polar diagrams or Smith Charts

See also the Reflection Coefficient article.

### Voltage standing wave ratio

The voltage standing wave ratio (VSWR) at a port, represented by the lower case 's', is a similar measure of port match to return loss but is a scalar linear quantity, the ratio of the standing wave maximum voltage to the standing wave minimum voltage. It therefore relates to the magnitude of the voltage reflection coefficient and hence to the magnitude of either ${\displaystyle S_{11}\,}$ for the input port or ${\displaystyle S_{22}\,}$ for the output port.

At the input port, the VSWR (${\displaystyle s_{\mathrm {in} }\,}$) is given by

${\displaystyle s_{\mathrm {in} }={\frac {1+\left|S_{11}\right|}{1-\left|S_{11}\right|}}\,}$

At the output port, the VSWR (${\displaystyle s_{\mathrm {out} }\,}$) is given by

${\displaystyle s_{\mathrm {out} }={\frac {1+\left|S_{22}\right|}{1-\left|S_{22}\right|}}\,}$

This is correct for reflection coefficients with a magnitude no greater than unity, which is usually the case. A reflection coefficient with a magnitude greater than unity, such as in a tunnel diode amplifier, will result in a negative value for this expression. VSWR, however, from its definition, is always positive. A more correct expression for port k of a multiport is;

${\displaystyle s_{k}={\frac {1+\left|S_{kk}\right|}{|1-\left|S_{kk}\right||}}\,}$

## 4-Port S-Parameters

4 Port S Parameters are used to characterize 4 port networks. They include information regarding the reflected and incident power waves between the 4 ports of the network.

${\displaystyle {\begin{pmatrix}S_{11}&S_{12}&S_{13}&S_{14}\\S_{21}&S_{22}&S_{23}&S_{24}\\S_{31}&S_{32}&S_{33}&S_{34}\\S_{41}&S_{42}&S_{43}&S_{44}\end{pmatrix}}}$

They are commonly used to analyze a pair of coupled transmission lines to determine the amount of cross-talk between them, if they are driven by two separate single ended signals, or the reflected and incident power of a differential signal driven across them. Many specifications of high speed differential signals define a communication channel in terms of the 4-Port S-Parameters, for example the 10-Gigabit Attachment Unit Interface (XAUI), SATA, PCI-X, and InfiniBand systems.

### 4-Port Mixed-Mode S-Parameters

4-Port mixed-Mode S-Parameters characterize a 4 port network in terms of the response of the network to common mode and differential stimulus signals. The following table displays the 4-Port Mixed-Mode S-Parameters.

Stimulus Differential Common Mode Port 1 SDD11 SDD12 SDC11 SDC12 SDD21 SDD22 SDC21 SDC22 SCD11 SCD12 SCC11 SCC12 SCD21 SCD22 SCC21 SCC22

Note the format of the parameter notation SXYab, where “S” stands for scattering parameter or S-parameter, “X” is the response mode (differential or common), “Y” is the stimulus mode (differential or common), “a” is the response (output) port and b is the stimulus (input) port. This is the typical nomenclature for scattering parameters.

The first quadrant is defined as the upper left 4 parameters describing the differential stimulus and differential response characteristics of the device under test. This is the actual mode of operation for most high-speed differential interconnects and is the quadrant that receives the most attention. It includes input differential return loss (SDD11), input differential insertion loss (SDD21), output differential return loss (SDD22) and output differential insertion loss (SDD12). Some benefits of differential signal processing are;

• reduced electromagnetic interference susceptibility
• reduction in electromagnetic radiation from balanced differential circuit
• even order differential distortion products transformed to common mode signals
• factor of two increase in voltage level relative to single-ended
• rejection to common mode supply and ground noise encoding onto differential signal

The second and third quadrants are the upper right and lower left 4 parameters, respectively. These are also referred to as the cross-mode quadrants. This is because they fully characterize any mode conversion occurring in the device under test, whether it is common-to-differential SDCab conversion (EMI susceptibility for an intended differential signal SDD transmission application) or differential-to-common SCDab conversion (EMI radiation for a differential application). Understanding mode conversion is very helpful when trying to optimize the design of interconnects for gigabit data throughput.

The fourth quadrant is the lower right 4 parameters and describes the performance characteristics of the common-mode signal SCCab propagating through the device under test. For a properly designed SDDab differential device there should be minimal common-mode output SCCab. However, the fourth quadrant common-mode response data is a measure of common-mode transmission response and used in a ratio with the differential transmission response to determine the network common-mode rejection. This common mode rejection is an important benefit of differential signal processing and can be reduced to one in some differential circuit implementations.[17][18]

## S-parameters in amplifier design

The reverse isolation parameter ${\displaystyle S_{12}\,}$ determines the level of feedback from the output of an amplifier to the input and therefore influences its stability (its tendency to refrain from oscillation) together with the forward gain ${\displaystyle S_{21}\,}$. An amplifier with input and output ports perfectly isolated from each other would have infinite scalar log magnitude isolation or the linear magnitude of ${\displaystyle S_{12}\,}$ would be zero. Such an amplifier is said to be unilateral. Most practical amplifiers though will have some finite isolation allowing the reflection coefficient 'seen' at the input to be influenced to some extent by the load connected on the output. An amplifier which is deliberately designed to have the smallest possible value of ${\displaystyle \left|S_{12}\right|\,}$ is often called a buffer amplifier.

Suppose the output port of a real (non-unilateral or bilateral) amplifier is connected to an arbitrary load with a reflection coefficient of ${\displaystyle \rho _{L}\,}$. The actual reflection coefficient 'seen' at the input port ${\displaystyle \rho _{\mathrm {in} }\,}$ will be given by[19]

${\displaystyle \rho _{\mathrm {in} }=S_{11}+{\frac {S_{12}S_{21}\rho _{L}}{1-S_{22}\rho _{L}}}\,}$.

If the amplifier is unilateral then ${\displaystyle S_{12}=0\,}$ and ${\displaystyle \rho _{\mathrm {in} }=S_{11}\,}$ or, to put it another way, the output loading has no effect on the input.

A similar property exists in the opposite direction, in this case if ${\displaystyle \rho _{\mathrm {out} }\,}$ is the reflection coefficient seen at the output port and ${\displaystyle \rho _{s}\,}$ is the reflection coefficient of the source connected to the input port.

${\displaystyle \rho _{out}=S_{22}+{\frac {S_{12}S_{21}\rho _{s}}{1-S_{11}\rho _{s}}}\,}$

### Port loading conditions for an amplifier to be unconditionally stable

An amplifier is unconditionally stable if a load or source of any reflection coefficient can be connected without causing instability. This condition occurs if the magnitudes of the reflection coefficients at the source, load and the amplifier's input and output ports are simultaneously less than unity. An important requirement that is often overlooked is that the amplifier be a linear network with no poles in the right half plane.[20] Instability can cause severe distortion of the amplifier's gain frequency response or, in the extreme, oscillation. To be unconditionally stable at the frequency of interest, an amplifier must satisfy the following 4 equations simultaneously:[21]

${\displaystyle \left|\rho _{s}\right|<1\,}$
${\displaystyle \left|\rho _{L}\right|<1\,}$
${\displaystyle \left|\rho _{\mathrm {in} }\right|<1\,}$
${\displaystyle \left|\rho _{\mathrm {out} }\right|<1\,}$

The boundary condition for when each of these values is equal to unity may be represented by a circle drawn on the polar diagram representing the (complex) reflection coefficient, one for the input port and the other for the output port. Often these will be scaled as Smith Charts. In each case coordinates of the circle centre and the associated radius are given by the following equations:

#### ${\displaystyle \rho _{L}\,}$ values for ${\displaystyle \left|\rho _{in}\right|=1\,}$ (output stability circle)

Radius ${\displaystyle r_{L}=\left|{\frac {S_{12}S_{21}}{\left|S_{22}\right|^{2}-\left|\Delta \right|^{2}}}\right|\,}$

Center ${\displaystyle c_{L}={\frac {(S_{22}-\Delta S_{11}^{*})^{*}}{\left|S_{22}\right|^{2}-\left|\Delta \right|^{2}}}\,}$

#### ${\displaystyle \rho _{S}\,}$ values for ${\displaystyle \left|\rho _{out}\right|=1\,}$ (input stability circle)

Radius ${\displaystyle r_{s}=\left|{\frac {S_{12}S_{21}}{\left|S_{11}\right|^{2}-\left|\Delta \right|^{2}}}\right|\,}$

Center ${\displaystyle c_{s}={\frac {(S_{11}-\Delta S_{22}^{*})^{*}}{\left|S_{11}\right|^{2}-\left|\Delta \right|^{2}}}\,}$

where, in both cases

${\displaystyle \Delta =S_{11}S_{22}-S_{12}S_{21}\,}$

and the superscript star (*) indicates a complex conjugate.

The circles are in complex units of reflection coefficient so may be drawn on impedance or admittance based Smith Charts normalised to the system impedance. This serves to readily show the regions of normalised impedance (or admittance) for predicted unconditional stability. Another way of demonstrating unconditional stability is by means of the Rollett stability factor (${\displaystyle K\,}$), defined as

${\displaystyle K={\frac {1-\left|S_{11}\right|^{2}-\left|S_{22}\right|^{2}+\left|\Delta \right|^{2}}{2\left|S_{12}S_{21}\right|}}\,}$

The condition of unconditional stability is achieved when ${\displaystyle K>1\,}$ and ${\displaystyle \left|\Delta \right|<1\,}$

### Scattering transfer parameters

The Scattering transfer parameters or T-parameters of a 2-port network are expressed by the T-parameter matrix and are closely related to the corresponding S-parameter matrix. However, unlike S parameters, there is no simple physical means to measure the T parameters in a system, sometimes referred to as Youla waves. The T-parameter matrix is related to the incident and reflected normalised waves at each of the ports as follows:

${\displaystyle {\begin{pmatrix}b_{1}\\a_{1}\end{pmatrix}}={\begin{pmatrix}T_{11}&T_{12}\\T_{21}&T_{22}\end{pmatrix}}{\begin{pmatrix}a_{2}\\b_{2}\end{pmatrix}}\,}$

However, they could be defined differently, as follows :

${\displaystyle {\begin{pmatrix}a_{1}\\b_{1}\end{pmatrix}}={\begin{pmatrix}T_{11}&T_{12}\\T_{21}&T_{22}\end{pmatrix}}{\begin{pmatrix}b_{2}\\a_{2}\end{pmatrix}}\,}$

The RF Toolbox add-on to MATLAB[22] and several books (for example "Network scattering parameters"[23]) use this last definition, so caution is necessary. The "From S to T" and "From T to S" paragraphs in this article are based on the first definition. Adaptation to the second definition is trivial (interchanging T11 for T22, and T12 for T21). The advantage of T-parameters compared to S-parameters is that providing reference impedances are purely, real or complex conjugate, they may be used to readily determine the effect of cascading 2 or more 2-port networks by simply multiplying the associated individual T-parameter matrices. If the T-parameters of say three different 2-port networks 1, 2 and 3 are ${\displaystyle {\begin{pmatrix}T_{1}\end{pmatrix}}\,}$, ${\displaystyle {\begin{pmatrix}T_{2}\end{pmatrix}}\,}$ and ${\displaystyle {\begin{pmatrix}T_{3}\end{pmatrix}}\,}$ respectively then the T-parameter matrix for the cascade of all three networks (${\displaystyle {\begin{pmatrix}T_{T}\end{pmatrix}}\,}$) in serial order is given by:

${\displaystyle {\begin{pmatrix}T_{T}\end{pmatrix}}={\begin{pmatrix}T_{1}\end{pmatrix}}{\begin{pmatrix}T_{2}\end{pmatrix}}{\begin{pmatrix}T_{3}\end{pmatrix}}\,}$

Note that matrix multiplication is not commutative, so the order is important. As with S-parameters, T-parameters are complex values and there is a direct conversion between the two types. Although the cascaded T-parameters is a simple matrix multiplication of the individual T-parameters, the conversion for each network's S-parameters to the corresponding T-parameters and the conversion of the cascaded T-parameters back to the equivalent cascaded S-parameters, which are usually required, is not trivial. However once the operation is completed, the complex full wave interactions between all ports in both directions will be taken into account. The following equations will provide conversion between S and T parameters for 2-port networks.[24]

From S to T:

${\displaystyle T_{11}={\frac {-\det {\begin{pmatrix}S\end{pmatrix}}}{S_{21}}}\,}$
${\displaystyle T_{12}={\frac {S_{11}}{S_{21}}}\,}$
${\displaystyle T_{21}={\frac {-S_{22}}{S_{21}}}\,}$
${\displaystyle T_{22}={\frac {1}{S_{21}}}\,}$

Where ${\displaystyle \det {\begin{pmatrix}S\end{pmatrix}}\,}$ indicates the determinant of the matrix ${\displaystyle {\begin{pmatrix}S\end{pmatrix}}\,}$.

${\displaystyle \det {\begin{pmatrix}S\end{pmatrix}}\ =S_{11}.S_{22}-S_{12}.S_{21},}$

From T to S

${\displaystyle S_{11}={\frac {T_{12}}{T_{22}}}\,}$
${\displaystyle S_{12}={\frac {\det {\begin{pmatrix}T\end{pmatrix}}}{T_{22}}}\,}$
${\displaystyle S_{21}={\frac {1}{T_{22}}}\,}$
${\displaystyle S_{22}={\frac {-T_{21}}{T_{22}}}\,}$

Where ${\displaystyle \det {\begin{pmatrix}T\end{pmatrix}}\,}$ indicates the determinant of the matrix ${\displaystyle {\begin{pmatrix}T\end{pmatrix}}\,}$.

${\displaystyle \det {\begin{pmatrix}T\end{pmatrix}}\ =T_{11}.T_{22}-T_{12}.T_{21},}$

## 1-port S-parameters

The S-parameter for a 1-port network is given by a simple 1 x 1 matrix of the form ${\displaystyle (s_{nn})\,}$ where n is the allocated port number. To comply with the S-parameter definition of linearity, this would normally be a passive load of some type.

## Higher-order S-parameter matrices

Higher order S-parameters for pairs of dissimilar ports (${\displaystyle S_{mn}\,}$), where ${\displaystyle m\neq \;n\,}$ may be deduced similarly to those for 2-port networks by considering pairs of ports in turn, in each case ensuring that all of the remaining (unused) ports are loaded with an impedance identical to the system impedance. In this way the incident power wave for each of the unused ports becomes zero yielding similar expressions to those obtained for the 2-port case. S-parameters relating to single ports only (${\displaystyle S_{mm}\,}$) require all of the remaining ports to be loaded with an impedance identical to the system impedance therefore making all of the incident power waves zero except that for the port under consideration. In general therefore we have:

${\displaystyle S_{mn}={\frac {b_{m}}{a_{n}}}\,}$

and

${\displaystyle S_{mm}={\frac {b_{m}}{a_{m}}}\,}$

For example, a 3-port network such as a 2-way splitter would have the following S-parameter definitions

${\displaystyle S_{11}={\frac {b_{1}}{a_{1}}}={\frac {V_{1}^{-}}{V_{1}^{+}}}\,}$
${\displaystyle S_{33}={\frac {b_{3}}{a_{3}}}={\frac {V_{3}^{-}}{V_{3}^{+}}}\,}$
${\displaystyle S_{32}={\frac {b_{3}}{a_{2}}}={\frac {V_{3}^{-}}{V_{2}^{+}}}\,}$
${\displaystyle S_{23}={\frac {b_{2}}{a_{3}}}={\frac {V_{2}^{-}}{V_{3}^{+}}}\,}$

## Measurement of S-parameters

S-parameters are most commonly measured with a vector network analyzer (VNA).

### Output format of measured and corrected S-parameter data

The S-parameter test data may be provided in many alternative formats, for example: list, graphical (Smith chart or polar diagram).

### List format

In list format the measured and corrected S-parameters are tabulated against frequency. The most common list format is known as Touchstone or SNP, where N is the number of ports. Commonly text files containing this information would have the filename extension '.s2p'. An example of a Touchstone file listing for the full 2-port S-parameter data obtained for a device is shown below:

! Created Fri Jul 21 14:28:50 2005
# MHZ S DB R 50
! SP1.SP
50	-15.4	100.2	10.2	173.5	-30.1	9.6	-13.4	57.2
51	-15.8	103.2	10.7	177.4	-33.1	9.6	-12.4	63.4
52	-15.9	105.5	11.2	179.1	-35.7	9.6	-14.4	66.9
53	-16.4	107.0	10.5	183.1	-36.6	9.6	-14.7	70.3
54	-16.6	109.3	10.6	187.8	-38.1	9.6	-15.3	71.4


Rows beginning with an exclamation mark contains only comments. The row beginning with the hash symbol indicates that in this case frequencies are in megahertz (MHZ), S-parameters are listed (S), magnitudes are in dB log magnitude (DB) and the system impedance is 50 Ohm (R 50). There are 9 columns of data. Column 1 is the test frequency in megahertz in this case. Columns 2, 4, 6 and 8 are the magnitudes of ${\displaystyle S_{11}\,}$, ${\displaystyle S_{21}\,}$, ${\displaystyle S_{12}\,}$ and ${\displaystyle S_{22}\,}$ respectively in dB. Columns 3, 5, 7 and 9 are the angles of ${\displaystyle S_{11}\,}$, ${\displaystyle S_{21}\,}$, ${\displaystyle S_{12}\,}$ and ${\displaystyle S_{22}\,}$ respectively in degrees.

### Graphical (Smith chart)

Any 2-port S-parameter may be displayed on a Smith chart using polar co-ordinates, but the most meaningful would be ${\displaystyle S_{11}\,}$ and ${\displaystyle S_{22}\,}$ since either of these may be converted directly into an equivalent normalized impedance (or admittance) using the characteristic Smith Chart impedance (or admittance) scaling appropriate to the system impedance.

### Graphical (polar diagram)

Any 2-port S-parameter may be displayed on a polar diagram using polar co-ordinates.

In either graphical format each S-parameter at a particular test frequency is displayed as a dot. If the measurement is a sweep across several frequencies a dot will appear for each.

### Measuring S-parameters of a one-port network

The S-parameter matrix for a network with just one port will have just one element represented in the form ${\displaystyle S_{nn}\,}$, where n is the number allocated to the port. Most VNAs provide a simple one-port calibration capability for one port measurement to save time if that is all that is required.

### Measuring S-parameters of networks with more than 2 ports

VNAs designed for the simultaneous measurement of the S-parameters of networks with more than two ports are feasible but quickly become prohibitively complex and expensive. Usually their purchase is not justified since the required measurements can be obtained using a standard 2-port calibrated VNA with extra measurements followed by the correct interpretation of the results obtained. The required S-parameter matrix can be assembled from successive two port measurements in stages, two ports at a time, on each occasion with the unused ports being terminated in high quality loads equal to the system impedance. One risk of this approach is that the return loss or VSWR of the loads themselves must be suitably specified to be as close as possible to a perfect 50 Ohms, or whatever the nominal system impedance is. For a network with many ports there may be a temptation, on grounds of cost, to inadequately specify the VSWRs of the loads. Some analysis will be necessary to determine what the worst acceptable VSWR of the loads will be.

Assuming that the extra loads are specified adequately, if necessary, two or more of the S-parameter subscripts are modified from those relating to the VNA (1 and 2 in the case considered above) to those relating to the network under test (1 to N, if N is the total number of DUT ports). For example, if the DUT has 5 ports and a two port VNA is connected with VNA port 1 to DUT port 3 and VNA port 2 to DUT port 5, the measured VNA results (${\displaystyle S_{11}\,}$, ${\displaystyle S_{12}\,}$, ${\displaystyle S_{21}\,}$ and ${\displaystyle S_{22}\,}$) would be equivalent to ${\displaystyle S_{33}\,}$, ${\displaystyle S_{35}\,}$, ${\displaystyle S_{53}\,}$ and ${\displaystyle S_{55}\,}$ respectively, assuming that DUT ports 1, 2 and 4 were terminated in adequate 50 Ohm loads . This would provide 4 of the necessary 25 S-parameters.

## References

1. ^ Pozar, David M. (2005); Microwave Engineering, Third Edition (Intl. Ed.); John Wiley & Sons, Inc.; pp. 170-174. ISBN 0-471-44878-8.
2. ^ Pozar, David M. (2005) (op. cit.); pp. 170-174.
3. ^ Pozar, David M. (2005) (op. cit.); pp. 183-186.
4. ^ Morton, A. H. (1985); Advanced Electrical Engineering; Pitman Publishing Ltd.; pp. 33-72. ISBN 0-273-40172-6.
5. ^ Belevitch, Vitold "Summary of the history of circuit theory", Proceedings of the IRE, vol.50, iss.5, pp. 848–855, May 1962.
Vandewalle, Joos "In memoriam – Vitold Belevitch", International Journal of Circuit Theory and Applications, vol.28, iss.5, pp. 429–430, September/October 2000.
6. ^ Valkenburg, Mac Elwyn Van Circuit Theory: Foundations and Classical Contributions, p.334, Stroudsburg, Pennsylvania: Dowden, Hutchinson & Ross, 1974 ISBN 0-87933-084-8.
7. ^ Dicke R. H. (1947). "A Computational Method Applicable to Microwave Networks". Journal of Applied Physics. 18: 873–878. Bibcode:1947JAP....18..873D. doi:10.1063/1.1697561.
8. ^ "Microwave Hall of Fame Part III". Microwaves 101. PN Designs. 2012. Retrieved December 9, 2012.
9. ^ Pozar, David M. (2005) (op. cit.); p. 170.
10. ^ Morton, A. H. (1985) (op. cit.); p. 33.
11. ^ Kurokawa, K., "Power Waves and the Scattering Matrix", IEEE Trans. Micr. Theory & Tech., Mar. 1965, pp. 194-202
12. ^ Pozar, David M. (2005) (op. cit.); p. 173.
13. ^ S-Parameter Design; Application Note AN 154; Agilent Technologies; p 7
14. ^ Choma J. & Chen W.K. (2007). Feedback networks: theory and circuit applications. Singapore: World Scientific. Chapter 3, p. 225 ff. ISBN 981-02-2770-1.
15. ^ Collin, Robert E.; Foundations For Microwave Engineering, Second Edition
16. ^ Trevor S. Bird, "Definition and Misuse of Return Loss", IEEE Antennas & Propagation Magazine, vol.51, iss.2, pp.166-167, April 2009.
17. ^ Backplane Channels and Correlation Between Their Frequency and Time Domain Performance
18. ^ Bockelman, DE and Eisenstadt, WR "Combined differential and common-mode scattering parameters: theory and simulation," MTT, IEEE transactions volume 43 issue 7 part 1–2 July 1995 pages 1530-1539
19. ^ Gonzalez, Guillermo (1997); Microwave Transistor Amplifiers Analysis and Design, Second Edition; Prentice Hall NJ; pp 212-216. ISBN 0-13-254335-4.
20. ^ J.M. Rollett, "Stability and Power-Gain Invariants of Linear Twoports", IRE Trans. on Circuit Theory vol. CT-9, pp. 29-32, March 1962
21. ^ Gonzalez, Guillermo (op. cit.); pp 217-222
22. ^
23. ^ R. Mavaddat. (1996). Network scattering parameter. Singapore: World Scientific. ISBN 978-981-02-2305-2.
24. ^ S-Parameter Design; Application Note AN 154; Agilent Technologies; p 14