Jump to content

Soft error

From Wikipedia, the free encyclopedia
(Redirected from Soft error rate)

In electronics and computing, a soft error is a type of error where a signal or datum is wrong. Errors may be caused by a defect, usually understood either to be a mistake in design or construction, or a broken component. A soft error is also a signal or datum which is wrong, but is not assumed to imply such a mistake or breakage. After observing a soft error, there is no implication that the system is any less reliable than before. One cause of soft errors is single event upsets from cosmic rays.

In a computer's memory system, a soft error changes an instruction in a program or a data value. Soft errors typically can be remedied by cold booting the computer. A soft error will not damage a system's hardware; the only damage is to the data that is being processed.

There are two types of soft errors, chip-level soft error and system-level soft error. Chip-level soft errors occur when particles hit the chip, e.g., when secondary particles from cosmic rays land on the silicon die. If a particle with certain properties hits a memory cell it can cause the cell to change state to a different value. The atomic reaction in this example is so tiny that it does not damage the physical structure of the chip. System-level soft errors occur when the data being processed is hit with a noise phenomenon, typically when the data is on a data bus. The computer tries to interpret the noise as a data bit, which can cause errors in addressing or processing program code. The bad data bit can even be saved in memory and cause problems at a later time.

If detected, a soft error may be corrected by rewriting correct data in place of erroneous data. Highly reliable systems use error correction to correct soft errors on the fly. However, in many systems, it may be impossible to determine the correct data, or even to discover that an error is present at all. In addition, before the correction can occur, the system may have crashed, in which case the recovery procedure must include a reboot. Soft errors involve changes to data‍—‌the electrons in a storage circuit, for example‍—‌but not changes to the physical circuit itself, the atoms. If the data is rewritten, the circuit will work perfectly again. Soft errors can occur on transmission lines, in digital logic, analog circuits, magnetic storage, and elsewhere, but are most commonly known in semiconductor storage.

Critical charge

[edit]

Whether or not a circuit experiences a soft error depends on the energy of the incoming particle, the geometry of the impact, the location of the strike, and the design of the logic circuit. Logic circuits with higher capacitance and higher logic voltages are less likely to suffer an error. This combination of capacitance and voltage is described by the critical charge parameter, Qcrit, the minimum electron charge disturbance needed to change the logic level. A higher Qcrit means fewer soft errors. Unfortunately, a higher Qcrit also means a slower logic gate and a higher power dissipation. Reduction in chip feature size and supply voltage, desirable for many reasons, decreases Qcrit. Thus, the importance of soft errors increases as chip technology advances.

In a logic circuit, Qcrit is defined as the minimum amount of induced charge required at a circuit node to cause a voltage pulse to propagate from that node to the output and be of sufficient duration and magnitude to be reliably latched. Since a logic circuit contains many nodes that may be struck, and each node may be of unique capacitance and distance from output, Qcrit is typically characterized on a per-node basis.

Causes of soft errors

[edit]

Alpha particles from package decay

[edit]

Soft errors became widely known with the introduction of dynamic RAM in the 1970s. In these early devices, ceramic chip packaging materials contained small amounts of radioactive contaminants. Very low decay rates are needed to avoid excess soft errors, and chip companies have occasionally suffered problems with contamination ever since. It is extremely hard to maintain the material purity needed. Controlling alpha particle emission rates for critical packaging materials to less than a level of 0.001 counts per hour per cm2 (cph/cm2) is required for reliable performance of most circuits. For comparison, the count rate of a typical shoe's sole is between 0.1 and 10 cph/cm2.

Package radioactive decay usually causes a soft error by alpha particle emission. The positive charged alpha particle travels through the semiconductor and disturbs the distribution of electrons there. If the disturbance is large enough, a digital signal can change from a 0 to a 1 or vice versa. In combinational logic, this effect is transient, perhaps lasting a fraction of a nanosecond, and this has led to the challenge of soft errors in combinational logic mostly going unnoticed. In sequential logic such as latches and RAM, even this transient upset can become stored for an indefinite time, to be read out later. Thus, designers are usually much more aware of the problem in storage circuits.

A 2011 Black Hat paper discusses the real-life security implications of such bit-flips in the Internet's Domain Name System. The paper found up to 3,434 incorrect requests per day due to bit-flip changes for various common domains. Many of these bit-flips would probably be attributable to hardware problems, but some could be attributed to alpha particles.[1] These bit-flip errors may be taken advantage of by malicious actors in the form of bitsquatting.

Isaac Asimov received a letter congratulating him on an accidental prediction of alpha-particle RAM errors in a 1950s novel.[2]

Cosmic rays creating energetic neutrons and protons

[edit]

Once the electronics industry had determined how to control package contaminants, it became clear that other causes were also at work. James F. Ziegler led a program of work at IBM which culminated in the publication of a number of papers (Ziegler and Lanford, 1979) demonstrating that cosmic rays also could cause soft errors. Indeed, in modern devices, cosmic rays may be the predominant cause. Although the primary particle of the cosmic ray does not generally reach the Earth's surface, it creates a shower of energetic secondary particles. At the Earth's surface approximately 95% of the particles capable of causing soft errors are energetic neutrons with the remainder composed of protons and pions.[3] IBM estimated in 1996 that one error per month per 256 MiB of RAM was expected for a desktop computer.[4] This flux of energetic neutrons is typically referred to as "cosmic rays" in the soft error literature. Neutrons are uncharged and cannot disturb a circuit on their own, but undergo neutron capture by the nucleus of an atom in a chip. This process may result in the production of charged secondaries, such as alpha particles and oxygen nuclei, which can then cause soft errors.

Cosmic ray flux depends on altitude. For the common reference location of 40.7° N, 74° W at sea level (New York City, NY, USA), the flux is approximately 14 neutrons/cm2/hour. Burying a system in a cave reduces the rate of cosmic-ray-induced soft errors to a negligible level. In the lower levels of the atmosphere, the flux increases by a factor of about 2.2 for every 1000 m (1.3 for every 1000 ft) increase in altitude above sea level. Computers operated on top of mountains experience an order of magnitude higher rate of soft errors compared to sea level. The rate of upsets in aircraft may be more than 300 times the sea level upset rate. This is in contrast to package decay-induced soft errors, which do not change with location.[5] As chip density increases, Intel expects the errors caused by cosmic rays to increase and become a limiting factor in design.[4]

The average rate of cosmic-ray soft errors is inversely proportional to sunspot activity. That is, the average number of cosmic-ray soft errors decreases during the active portion of the sunspot cycle and increases during the quiet portion. This counter-intuitive result occurs for two reasons. The Sun does not generally produce cosmic ray particles with energy above 1 GeV that are capable of penetrating to the Earth's upper atmosphere and creating particle showers, so the changes in the solar flux do not directly influence the number of errors. Further, the increase in the solar flux during an active sun period does have the effect of reshaping the Earth's magnetic field providing some additional shielding against higher energy cosmic rays, resulting in a decrease in the number of particles creating showers. The effect is fairly small in any case resulting in a ±7% modulation of the energetic neutron flux in New York City. Other locations are similarly affected.[citation needed]

One experiment measured the soft error rate at the sea level to be 5,950 failures in time (FIT = failures per billion hours) per DRAM chip. When the same test setup was moved to an underground vault, shielded by over 50 feet (15 m) of rock that effectively eliminated all cosmic rays, zero soft errors were recorded.[6] In this test, all other causes of soft errors are too small to be measured, compared to the error rate caused by cosmic rays.

Energetic neutrons produced by cosmic rays may lose most of their kinetic energy and reach thermal equilibrium with their surroundings as they are scattered by materials. The resulting neutrons are simply referred to as thermal neutrons and have an average kinetic energy of about 25 millielectron-volts at 25 °C. Thermal neutrons are also produced by environmental radiation sources, including the decay of naturally occurring radioactive elements such as uranium and thorium. The thermal neutron flux from sources other than cosmic-ray showers may still be noticeable in an underground location and an important contributor to soft errors for some circuits.

Thermal neutrons

[edit]

Neutrons that have lost kinetic energy until they are in thermal equilibrium with their surroundings are an important cause of soft errors for some circuits. At low energies many neutron capture reactions become much more probable and result in fission of certain materials creating charged secondaries as fission byproducts. For some circuits the capture of a thermal neutron by the nucleus of the 10B isotope of boron is particularly important. This nuclear reaction is an efficient producer of an alpha particle, 7Li nucleus and gamma ray. Either of the charged particles (alpha or 7Li) may cause a soft error if produced in very close proximity, approximately 5 μm, to a critical circuit node. The capture cross section for 11B is 6 orders of magnitude smaller and does not contribute to soft errors.[7]

Boron has been used in BPSG, the insulator in the interconnection layers of integrated circuits, particularly in the lowest one. The inclusion of boron lowers the melt temperature of the glass providing better reflow and planarization characteristics. In this application the glass is formulated with a boron content of 4% to 5% by weight. Naturally occurring boron is 20% 10B with the remainder the 11B isotope. Soft errors are caused by the high level of 10B in this critical lower layer of some older integrated circuit processes. Boron-11, used at low concentrations as a p-type dopant, does not contribute to soft errors. Integrated circuit manufacturers eliminated borated dielectrics by the time individual circuit components decreased in size to 150 nm, largely due to this problem.

In critical designs, depleted boron‍—‌consisting almost entirely of boron-11‍—‌is used, to avoid this effect and therefore to reduce the soft error rate. Boron-11 is a by-product of the nuclear industry.

For applications in medical electronic devices this soft error mechanism may be extremely important. Neutrons are produced during high-energy cancer radiation therapy using photon beam energies above 10 MeV. These neutrons are moderated as they are scattered from the equipment and walls in the treatment room resulting in a thermal neutron flux that is about 40 × 106 higher than the normal environmental neutron flux. This high thermal neutron flux will generally result in a very high rate of soft errors and consequent circuit upset.[8][9]

Other causes

[edit]

Soft errors can also be caused by random noise or signal integrity problems, such as inductive or capacitive crosstalk. However, in general, these sources represent a small contribution to the overall soft error rate when compared to radiation effects.

Some tests conclude that the isolation of DRAM memory cells can be circumvented by unintended side effects of specially crafted accesses to adjacent cells. Thus, accessing data stored in DRAM causes memory cells to leak their charges and interact electrically, as a result of high cells density in modern memory, altering the content of nearby memory rows that actually were not addressed in the original memory access.[10] This effect is known as row hammer, and it has also been used in some privilege escalation computer security exploits.[11][12]

Designing around soft errors

[edit]

Soft error mitigation

[edit]

A designer can attempt to minimize the rate of soft errors by judicious device design, choosing the right semiconductor, package and substrate materials, and the right device geometry. Often, however, this is limited by the need to reduce device size and voltage, to increase operating speed and to reduce power dissipation. The susceptibility of devices to upsets is described in the industry using the JEDEC JESD-89 standard.

One technique that can be used to reduce the soft error rate in digital circuits is called radiation hardening. This involves increasing the capacitance at selected circuit nodes in order to increase its effective Qcrit value. This reduces the range of particle energies to which the logic value of the node can be upset. Radiation hardening is often accomplished by increasing the size of transistors who share a drain/source region at the node. Since the area and power overhead of radiation hardening can be restrictive to design, the technique is often applied selectively to nodes which are predicted to have the highest probability of resulting in soft errors if struck. Tools and models that can predict which nodes are most vulnerable are the subject of past and current research in the area of soft errors.

Detecting soft errors

[edit]

There has been work addressing soft errors in processor and memory resources using both hardware and software techniques. Several research efforts addressed soft errors by proposing error detection and recovery via hardware-based redundant multi-threading.[13][14][15] These approaches used special hardware to replicate an application execution to identify errors in the output, which increased hardware design complexity and cost including high performance overhead. Software-based soft error tolerant schemes, on the other hand, are flexible and can be applied on commercial off-the-shelf microprocessors. Many works propose compiler-level instruction replication and result checking for soft error detection. [16][17] [18]

Correcting soft errors

[edit]

Designers can choose to accept that soft errors will occur, and design systems with appropriate error detection and correction to recover gracefully. Typically, a semiconductor memory design might use forward error correction, incorporating redundant data into each word to create an error correcting code. Alternatively, roll-back error correction can be used, detecting the soft error with an error-detecting code such as parity, and rewriting correct data from another source. This technique is often used for write-through cache memories.

Soft errors in logic circuits are sometimes detected and corrected using the techniques of fault tolerant design. These often include the use of redundant circuitry or computation of data, and typically come at the cost of circuit area, decreased performance, and/or higher power consumption. The concept of triple modular redundancy (TMR) can be employed to ensure very high soft-error reliability in logic circuits. In this technique, three identical copies of a circuit compute on the same data in parallel and outputs are fed into majority voting logic, returning the value that occurred in at least two of three cases. In this way, the failure of one circuit due to soft error is discarded assuming the other two circuits operated correctly. In practice, however, few designers can afford the greater than 200% circuit area and power overhead required, so it is usually only selectively applied. Another common concept to correct soft errors in logic circuits is temporal (or time) redundancy, in which one circuit operates on the same data multiple times and compares subsequent evaluations for consistency. This approach, however, often incurs performance overhead, area overhead (if copies of latches are used to store data), and power overhead, though is considerably more area-efficient than modular redundancy.

Traditionally, DRAM has had the most attention in the quest to reduce or work around soft errors, due to the fact that DRAM has comprised the majority-share of susceptible device surface area in desktop, and server computer systems (ref. the prevalence of ECC RAM in server computers). Hard figures for DRAM susceptibility are hard to come by, and vary considerably across designs, fabrication processes, and manufacturers. 1980s technology 256 kilobit DRAMS could have clusters of five or six bits flip from a single alpha particle. Modern DRAMs have much smaller feature sizes, so the deposition of a similar amount of charge could easily cause many more bits to flip.

The design of error detection and correction circuits is helped by the fact that soft errors usually are localised to a very small area of a chip. Usually, only one cell of a memory is affected, although high energy events can cause a multi-cell upset. Conventional memory layout usually places one bit of many different correction words adjacent on a chip. So, even a multi-cell upset leads to only a number of separate single-bit upsets in multiple correction words, rather than a multi-bit upset in a single correction word. So, an error correcting code needs only to cope with a single bit in error in each correction word in order to cope with all likely soft errors. The term 'multi-cell' is used for upsets affecting multiple cells of a memory, whatever correction words those cells happen to fall in. 'Multi-bit' is used when multiple bits in a single correction word are in error.

Soft errors in combinational logic

[edit]

The three natural masking effects in combinational logic that determine whether a single event upset (SEU) will propagate to become a soft error are electrical masking, logical masking, and temporal (or timing-window) masking. An SEU is logically masked if its propagation is blocked from reaching an output latch because off-path gate inputs prevent a logical transition of that gate's output. An SEU is electrically masked if the signal is attenuated by the electrical properties of gates on its propagation path such that the resulting pulse is of insufficient magnitude to be reliably latched. An SEU is temporally masked if the erroneous pulse reaches an output latch, but it does not occur close enough to when the latch is actually triggered to hold.

If all three masking effects fail to occur, the propagated pulse becomes latched and the output of the logic circuit will be an erroneous value. In the context of circuit operation, this erroneous output value may be considered a soft error event. However, from a microarchitectural-level standpoint, the affected result may not change the output of the currently-executing program. For instance, the erroneous data could be overwritten before use, masked in subsequent logic operations, or simply never be used. If erroneous data does not affect the output of a program, it is considered to be an example of microarchitectural masking.

Soft error rate

[edit]

Soft error rate (SER) is the rate at which a device or system encounters or is predicted to encounter soft errors. It is typically expressed as either the number of failures-in-time (FIT) or mean time between failures (MTBF). The unit adopted for quantifying failures in time is called FIT, which is equivalent to one error per billion hours of device operation. MTBF is usually given in years of device operation; to put it into perspective, one FIT equals to approximately 1,000,000,000 / (24 × 365.25) = 114,077 times longer between errors than one-year MTBF.

While many electronic systems have an MTBF that exceeds the expected lifetime of the circuit, the SER may still be unacceptable to the manufacturer or customer. For instance, many failures per million circuits due to soft errors can be expected in the field if the system does not have adequate soft error protection. The failure of even a few products in the field, particularly if catastrophic, can tarnish the reputation of the product and company that designed it. Also, in safety- or cost-critical applications where the cost of system failure far outweighs the cost of the system itself, a 1% risk of soft error failure per lifetime may be too high to be acceptable to the customer. Therefore, it is advantageous to design for low SER when manufacturing a system in high-volume or requiring extremely high reliability.

See also

[edit]

References

[edit]
  1. ^ Artem Dinaburg (July 2011). "Bitsquatting - DNS Hijacking without Exploitation" (PDF). Archived from the original (PDF) on 2018-06-11. Retrieved 2011-12-26.
  2. ^ Gold (1995): "This letter is to inform you and congratulate you on another remarkable scientific prediction of the future; namely your foreseeing of the dynamic random-access memory (DRAM) logic upset problem caused by alpha particle emission, first observed in 1977, but written about by you in Caves of Steel in 1957." [Note: Actually, 1952.] ... "These failures are caused by trace amounts of radioactive elements present in the packaging material used to encapsulate the silicon devices ... in your book, Caves of Steel, published in the 1950s, you use an alpha particle emitter to 'murder' one of the robots in the story, by destroying ('randomizing') its positronic brain. This is, of course, as good a way of describing a logic upset as any I've heard ... our millions of dollars of research, culminating in several international awards for the most important scientific contribution in the field of reliability of semiconductor devices in 1978 and 1979, was predicted in substantially accurate form twenty years [Note: twenty-five years, actually] before the events took place
  3. ^ Ziegler, J. F. (January 1996). "Terrestrial cosmic rays". IBM Journal of Research and Development. 40 (1): 19–39. doi:10.1147/rd.401.0019. ISSN 0018-8646.
  4. ^ a b Simonite, Tom (March 2008). "Should every computer chip have a cosmic ray detector?". New Scientist. Archived from the original on 2011-12-02. Retrieved 2019-11-26.
  5. ^ Gordon, M. S.; Goldhagen, P.; Rodbell, K. P.; Zabel, T. H.; Tang, H. H. K.; Clem, J. M.; Bailey, P. (2004). "Measurement of the flux and energy spectrum of cosmic-ray induced neutrons on the ground". IEEE Transactions on Nuclear Science. 51 (6): 3427–3434. Bibcode:2004ITNS...51.3427G. doi:10.1109/TNS.2004.839134. ISSN 0018-9499. S2CID 9573484.
  6. ^ Dell, Timothy J. (1997). "A White Paper on the Benefits of Chipkill-Correct ECC for PC Server Main Memory" (PDF). ece.umd.edu. p. 13. Retrieved 2021-11-03.
  7. ^ Baumann, R.; Hossain, T.; Murata, S.; Kitagawa, H. (1995). "Boron compounds as a dominant source of alpha particles in semiconductor devices". 33rd IEEE International Reliability Physics Symposium. pp. 297–302. doi:10.1109/RELPHY.1995.513695. ISBN 978-0-7803-2031-4. S2CID 110078856.
  8. ^ Wilkinson, J. D.; Bounds, C.; Brown, T.; Gerbi, B. J.; Peltier, J. (2005). "Cancer-radiotherapy equipment as a cause of soft errors in electronic equipment". IEEE Transactions on Device and Materials Reliability. 5 (3): 449–451. doi:10.1109/TDMR.2005.858342. ISSN 1530-4388. S2CID 20789261.
  9. ^ Franco, L., Gómez, F., Iglesias, A., Pardo, J., Pazos, A., Pena, J., Zapata, M., SEUs on commercial SRAM induced by low energy neutrons produced at a clinical linac facility, RADECS Proceedings, September 2005
  10. ^ Park, Kyungbae; Baeg, Sanghyeon; Wen, ShiJie; Wong, Richard (October 2014). "Active-precharge hammering on a row induced failure in DDR3 SDRAMs under 3× nm technology". 2014 IEEE International Integrated Reliability Workshop Final Report (IIRW). IEEE. pp. 82–85. doi:10.1109/IIRW.2014.7049516. ISBN 978-1-4799-7308-8. S2CID 14464953.
  11. ^ Kim, Yoongu; Daly, Ross; Kim, Jeremie; Fallin, Chris; Lee, Ji Hye; Lee, Donghyuk; Wilkerson, Chris; Lai, Konrad; Mutlu, Onur (2014-06-24). "Flipping Bits in Memory Without Accessing Them: An Experimental Study of DRAM Disturbance Errors" (PDF). ece.cmu.edu. IEEE. Retrieved 2015-03-10.
  12. ^ Goodin, Dan (2015-03-10). "Cutting-edge hack gives super user status by exploiting DRAM weakness". Ars Technica. Retrieved 2015-03-10.
  13. ^ Reinhardt, Steven K.; Mukherjee, Shubhendu S. (2000). "Transient fault detection via simultaneous multithreading". ACM SIGARCH Computer Architecture News. 28 (2): 25–36. CiteSeerX 10.1.1.112.37. doi:10.1145/342001.339652. ISSN 0163-5964.
  14. ^ Mukherjee, Shubhendu S.; Kontz, Michael; Reinhardt, Steven K. (2002). "Detailed design and evaluation of redundant multithreading alternatives". ACM SIGARCH Computer Architecture News. 30 (2): 99. CiteSeerX 10.1.1.13.2922. doi:10.1145/545214.545227. ISSN 0163-5964. S2CID 1909214.
  15. ^ Vijaykumar, T. N.; Pomeranz, Irith; Cheng, Karl (2002). "Transient-fault recovery using simultaneous multithreading". ACM SIGARCH Computer Architecture News. 30 (2): 87. doi:10.1145/545214.545226. ISSN 0163-5964. S2CID 2270600.
  16. ^ Nahmsuk, Oh; Shirvani, Philip P.; McCluskey, Edward J. (2002). "Error detection by duplicated instructions in super-scalar processors". IEEE Transactions on Reliability. 51: 63–75. doi:10.1109/24.994913.
  17. ^ Reis A., George A.; Chang, Jonathan; Vachharajani, Neil; Rangan, Ram; August, David I. (2005). "SWIFT: Software implemented fault tolerance". International Symposium on Code Generation and Optimization. Proceedings of the international symposium on Code generation and optimization. pp. 243–254. CiteSeerX 10.1.1.472.4177. doi:10.1109/CGO.2005.34. ISBN 978-0-7695-2298-2. S2CID 5746979.{{cite book}}: CS1 maint: location missing publisher (link)
  18. ^ Didehban, Moslem; Shrivastava, Aviral (2016), "NZDC: A compiler technique for near zero silent data corruption", Proceedings of the 53rd Annual Design Automation Conference, Proceedings of the 53rd Annual Design Automation Conference (DAC): ACM, p. 48, doi:10.1145/2897937.2898054, ISBN 9781450342360, S2CID 5618907{{citation}}: CS1 maint: location (link)

Further reading

[edit]
[edit]