Window film

"Tinted windows" redirects here. For the musical group, see Tinted Windows (band).

Terminology

Window Film is a retrofit upgrade that is generally installed to flat glass in existing buildings. When installed to vehicles it is referred to as Window Tinting. This is due to the fact that the large majority of automotive window films are dark coloured (tinted), whereas window films for commercial installation are typically clear. The two industries are complementry, and many installation companies offer both services.yo yo yo

Use

There are many types, grades, shades, colours and thicknesses of window films available today. Window Films are a retrofit upgrade for existing glass that can be used to address a range of problems inherent to glazing, such as: Heat and Glare reduction, Thermal insulation, UV Filtration, Safety and Security, Privacy, Decoration, Graffiti protection

Window Films are an extremely cost effetive method to reduce heating and cooling costs in existing buildings by reducing the amount of heat transfer through glazing. "

Primary properties

The colorful film on these windows gives the building a unique appearance while providing privacy and insulation from the sun.

Heat rejection films are normally applied to the interior of flat glass windows to reduce the amount of infrared, visible light, and ultraviolet (UV) radiation entering windows. Such films are usually dyed or metalized (which can be transparent to visible light) to convert incoming solar radiation to infrared radiation, which is then rejected back through the glass to the exterior." Modern window film technology has created Ceramic Window Film which are non-metallic and do not contain dyes that can result in discoloration. The ceramic and metallic window films usually cost 10–15 percent more than regular window film but can reduce energy transmission by as much as 80 percent." Ceramic window films cost slightly more but provide a substantial increase in blocking UV rays and ability to control heat transfer.

To keep the sun's heat out of the house, a low-emissivity coating should be applied to the outside pane of glazed windows. If the windows are designed to provide heat energy in the winter and keep heat inside the house (typical of cold climates), the low-emissivity coating should be applied to the inside pane of glazed windows. Such films also reduce the amount of visible and ultraviolet radiation entering a window, and are often applied to reduce fading of the contents of a room. Silvered film may also be employed to the same end. Spectrally selective films act by blocking certain wavelengths of the sun's infrared radiation and reject heat without reducing natural light.

Security films are applied to prevent glass from shattering. Typically applied to commercial glass, these films are made of heavy-gauge plastic and are intended to maintain the integrity of glass when subject to heavy impact. The most robust security films are capable of preventing fragmentation and the production of hazardous glass shards from forces such as bomb blasts. Some companies have even experimented with bullet ballistics of multiple layers of security film. Another key application for security window films (safety window films)is on large areas of "flat glass" such as storefront windows, sliding glass doors, and larger windows that are prone to hurricane damage. These security films, if applied properly, can also provide protection for vehicles. These security films are often tinted and can be up to 400 micrometers (µm) thick, compared to less than 50 µm for ordinary tint films. If anchored correctly, they can also provide protection for architectural glazing in the event of an explosion. A layer of film (of 100 µm thickness or greater) can prevent the ejection of spall when a projectile impacts on its surface, creating small dagger-like shards of glass that can cause injury.

Switchable films can be switched from opaque to clear by a safe voltage under 36V AC. In its opaque state, it can be perfectly used as a projection screen that is viewable from both sides. 3G switchable film also has UV (100%) and IR (94%) blocking functions and security function.

Graphic design films are generally colored vinyl or frosted. Frosted finish films closely resemble sandblasted or acid-etched glass, while vinyl films are available in a range of colors. Both types of films are commonly used in commercial applications.

Privacy films reduce visibility through the glass. Privacy film for flat-glass commercial and residential applications may be silvered, offering an unimpeded view from the low-light side but virtually no view from the high-light side. It may also be frosted, rendering the window translucent but not transparent. Privacy films for automobiles are available in gradients of darkness, with the darker tints commonly known as "limo tint."

Correctly-applied mirror film can create one-way mirrors.

Other benefits include protection for passengers in the rear, protection from UV rays (which have some harmful effects), cooling for pets, greater privacy, reduced chance of theft (because valuables are less visible), reduced glare and reflection on liquid crystal display (LCD) screens, and protection for those who have conditions involving photosensitivity or skin sensitivity, such as lupus (SLE). Window film is also considered more effective and practical than stick-on blinds.

UV Window Films

The adhesive system used in window films rejects UV Radiation up to 380 nm. As UV is one of the main sources of fading, {{citation}}: Empty citation (help) it can prolong the life of fixtures and fittings. Specialist UV Window Films are available that offer increased protection to 400 nm. These films are usually clear and are widely available. For yet further protection to 500 nm, Tinted Amber window films are available.

Window Film and Fading

Window Films filter out over 99% of UV Rays to 380 nm - helping to reduce the main contributor to fading. However, additional factors such as Solar Heat and Visible Light also contribute to fading. Therefore the greatest protection from fading is offered by tinted or metallised window films that reject large levels of heat and visible light - in addition to UV. {{citation}}: Empty citation (help)

Selection of window film

Not all films are suitable for all glass. You must consider the absorptance of the glass and the film, the size of the pane, the thickness of the glass, the construction of the window – is it single pane, insulated glass, treated (with a low-emissivity coating), laminated or toughened.

Advice on the appropriate selection of film for the glass is vital to ensure that the glass does not crack as a result of thermal stress. However, it is possible that a pane of glass may break subsequent to the application of an appropriate film, because the pane has been damaged during the glazing of the window, or as a result of movement of the building or other physical stresses that are not apparent at the time of the application of the film.

Glass may crack subsequent to the application of sign writing or if heavy, thermally efficient drapes are hung close to the glass, particularly if the edges of the glass are damaged.

The chances of glass breakage occurring subsequent to the application of film or sign writing or the hanging of drapes, are very small. However breakage can occur and it is impossible to predict the edge condition of the glass without removing it from the frame – an approach that is not practical.

Unintended features

Under certain conditions, window film will exhibit iridescence. This phenomenon usually occurs at night, when the source of illumination within a building is fluorescent lighting.

The amount of iridescence may vary from almost imperceptible to very visible. It most frequently occurs when the film is constructed with scratch resistance protection.

When iridescence does occur in window film, the best way to stop it is to prevent the fluorescent light from illuminating the film or to use an alternative type of light.

Certification and standards

The thicker window films known as safety and security window film are designed to perform under extreme conditions, and as such there are specific standard criteria these films should meet, such as American standards ANSI Z.97, CPSC 16 CFR 1201, Cat II (400 ft-lb), and the British Standards BS 6206 (Class A, B, C). The European Committee for Standardization offer the EN12600 standard Classification of Resistance of Glazing to Impact. Often, building codes dictate that a film must have a report verifying that it has met at least one of these standards.

Solar window film is usually subject to less critical testing. However, standards are in place to maintain a level of quality in the industry. The ANSI Standards ASTM E903 and ASTM D1044-93 relate to the solar/UV transmission properties and abrasion resistance, respectively. The larger window film manufacturers use these standards to guarantee the quality of their raw materials and finished products.

Regulations for automotive use

Window tint on a convertible in America. Tint on the front window is lighter than on the back window because of window tint laws.

Photo of vehicle with illegal window tint being measured at 2% light transmittance.

Automobile window tinting reduces the visible light transmission (VLT) through car windows. This can be problematic at night, when motorists must be able to see through the windows of other vehicles in order to spot hazards which would otherwise be obstructed. Police also may want to be able to identify the passengers in a vehicle.

In many jurisdictions, there are laws to ensure darkness of films do not present a danger to motorists:

U.S.

Tint Limits by U.S. state (when measured on the front side window):

State	VLT	State	VLT	State	VLT
Alabama	32%	Louisiana	40% State Law	Ohio	50%
Alaska	70%	Maine	35%	Oklahoma	25%
Arizona	30% to 36%***	Maryland	35%	Oregon	35% State Law
Arkansas	25%	Massachusetts	35%	Pennsylvania	70%
California	70%	Michigan	70% State Law	Rhode Island	70%
Colorado	27%	Minnesota	50%	South Carolina	27%
Connecticut	35%	Mississippi	28%	South Dakota	35%
Delaware	70%	Missouri	35%	Tennessee	35%
Florida	28%	Montana	24%	Texas	25% [5]
Georgia	32%	Nebraska	35%	Utah	43%
Hawaii	35%	Nevada	35%	Vermont	70%
Idaho	35%	New Hampshire	70%	Virginia	35%
Illinois	35%	New Jersey	70%	Washington	24%
Indiana	30% state law	New Mexico	20%	West Virginia	35%
Iowa	70%	New York	75%	Wisconsin	50%
Kansas	35%	North Carolina	35%	Wyoming	28%
Kentucky	35%	North Dakota	50%	District of Columbia	70%

Current as of 17 July 2010

(Lower number is less light transmittance, thus darker tint)

Full details of other glazing and sticker rules can be found at the Federal Motor Carrier Safety Administration page

It is quite common for states to provide more stringent regulations on tinting front windows as opposed to those located in the rear of the vehicle.

In other countries

• In Canada, automobile tinting laws are set at the provincial level.
• In the United Kingdom, regulations set forth by the Vehicle and Operator Services Agency under the Road Vehicles (Construction and Use) Regulations 1986 provide that all front windows in front of the B post can have no less than 70 percent VLT. Windscreens are only allowed tinting outside the sweep of the windscreen wipers to a maximum of six inches from the top of the windscreen. British police are increasingly cracking down on illegal tinting on vehicles.
• In Russia, window tinting limits are specified in GOST 5727-88. The limit is 75% for the front windshield (a darker stripe no wider than 10 cm is allowed at the very top) and 70% for the front side windows. Tinting of back windows is not regulated. In practice, however, bribes are often used to pass inspection or avoid road police tickets even with illegal tint.
• In Belarus, any kind of window tint is illegal. An exception is made for factory tint in vehicles purchased before 1 April 2006. Also exempt are vehicles of cash collectors, KGB and certain officials.
• In New South Wales, Australia; the Roads and Traffic Authority permits VLT of 35% on ALL windows. Tint on the windscreen – a band across the top is permitted with a depth of no more than 10% of the depth of the windscreen. An exception to the side & rear window tinting regulations applies to cars tinted before 1 August 1994.
• In New Zealand; the New Zealand Transport Agency stipulates that private motor vehicles must have at least 35% VLT after film has been applied. Side and rear windows; including the windows next to the driver; are allowed full coverage. The front windshield may have an anti-glare band no lower than the extended sun visors. There is no concise regulation for a sunroof. There is an exception for factory tinted glass, which may be any VLT level. Also, commercial goods vehicles are allowed any level of VLT on windows behind the driver, provided the driver has adequate rear vision via side mirrors.
• In Malta; The Malta Transport Authority Permits VLT of 70% on Front Side windows. Tint on the windscreen – a band across the top is permitted with a depth of no more than 100mm of the depth of the windscreen. 30% on the rear and side windows.
• In India; The rules governing the Tinted glass are defined in the THE MOTOR VEHICLES ACT, 1988 states that the front and rear windshield should be 70% VLT and all other windows are limited at 50% VLT. Supreme court on April 27, 2012 ordered that all tint be removed

Non-automotive uses

Window tint can be applied to any object made of glass. Many window tint companies will tint shopfronts windows, office block windows and house windows. Some will even tint objects such as mirrors and coffee tables giving unique looks to everyday objects.

Homes can be tinted to save energy, fight heat, and increase privacy. Decorative films are offered in many styles and shades that can dress up a space such as an office waiting room, bathrooms, and more.

See also

• One-way mirror
• Smoked glass
• Smart glass