Ground source heat pump

Ground source heating and air conditioning

A geothermal heat pump system is a heating and/or an air conditioning system that uses the Earth's ability to store heat in the ground and water thermal masses. These systems operate on a stability of underground temperatures; the ground a few feet below surface has a very stable temperature throughout the year, typically somewhere in range of 50-85 °F (10-30 °C) depending upon location's annual climate. A water-source heat pump uses that available heat in the winter and puts heat back into the ground in the summer. A geothermal system differs from a conventional furnace or boiler by its ability to transfer heat versus the standard method of producing the heat. As energy costs continue to rise and pollution concerns continue to be a hot topic, geothermal systems may hold a solution to both of these concerns. A particular advantage is that they can use electricity produced from renewable sources, like solar and wind power, to heat spaces and water much more efficiently than an electric heater. This allows buildings to be heated with renewable energy without transporting and burning biomass on site, producing biogas for use in gas furnaces or relying solely upon solar heating.

Geothermal heat pumps are also known as "geo-exchange" systems (a term created by an industry association) and "ground-source heat pumps." The latter term is useful as it clearly distinguishes the technology from air-source heat pumps. Geothermal heat pumps, which can be used in almost any region, should also be distinguished from geothermal heating. Geothermal heating is used in areas where exceptionally high underground temperatures, such as those at hot springs and steam vents, are used to heat indoor spaces without the use of a heat pump.

This article focuses on geothermal heat pumps that use water to exchange heat with the ground, often referred to as "water-source geothermal heat pumps" or "water loop geothermal heat pumps." Another technology, the direct exchange geothermal heat pump, is also available and is briefly discussed.

Introduction

A geothermal heat pump is a heat pump that uses the Earth as either a heat source, when operating in heating mode, or a heat sink, when operating in cooling mode.

Geothermal heat pumps can be characterised as having one or two loops. The heat pump itself, explained more fully in the article on heat pumps, consists of a loop containing refrigerant. The refrigerant is pumped through a vapor-compression refrigeration cycle that moves heat from a cooler area to a warmer one.

In a single loop system, the copper tubing refrigerant loop actually leaves the heat pump appliance cabinet and goes out of the house and under the ground and directly exchanges heat with the ground before returning to the appliance. Hence the name "direct exchange" or DX. In a double loop system, the refrigerant loop exchanges heat with a secondary loop made of plastic pipe containing water and anti-freeze (propylene glycol, denatured alcohol or methanol). After leaving the heat exchanger, the plastic pipe then leaves the appliance cabinet, and goes out of the house and under the ground before returning, so the water is exchanging heat with the ground. This is known as a water-source system. Secondary loops are popular for ground use because they are not pressurized, so cheap plastic tubing can be used, and because they reduce the amount of expensive refrigerant required. Copper loop DX systems are gaining acceptance due to their increased efficiency and lower installation costs.

Components

Pump pack

Geothermal systems require three primary components; a loop field on the property, a liquid pump pack and a water-source heat pump. A loop field can be installed horizontally or vertically on the property; we will focus on the different types of loop fields later in this article. The purpose of the loop field is to transfer heat to and from the ground. The size of the loop field depends on the size of the building being conditioned. Typically, one loop (400 to 600 feet)has the capacity of one ton or 12,000 British thermal units per hour (BTU/h) or 3.5 kilowatts. An average house will range from 3 to 5 tons (10 to 18 kW) of capacity. The second component is a liquid pump pack, which sends the water through the loop field and the water-source heat pump. An example of an installed liquid pump pack can be seen in the image to the right. Lastly, the water-source heat pump is the unit that replaces the existing furnace or boiler. This is where the heat from the loop field is transferred for heating the structure. Heat pumps have the ability to capture heat at one temperature reservoir and transfer it to another temperature reservoir. An example of a heat pump is a refrigerator; heat is removed from the refrigerator's compartments and transferred to the outside. (See the article on heat pumps for more information regarding heat pumps.)

Common Systems

Closed loop fields

3-ton slinky loop

12-ton pond loop

12-ton pond loop

A closed loop system, the most common, circulates the fluid through the loop fields’ pipes. In a closed loop system there is no direct interaction between the fluid and the earth; only heat transfer across the pipe. The amount of vertical or horizontal loop required is a function of the ground formation thermal conductivity, deep earth temperature, and heating and cooling power needed, and also depends on the balance between the amount of heat rejected to and absorbed from the ground during the course of the year. A rough approximation of the soil temperature is the average daily temperature for the region. There are four common types of closed loop systems; vertical, horizontal, slinky, and pond. (Slinky and pond loops depicted below.)

Vertical closed loop field

A vertical closed loop field is composed of pipes that run vertically in the ground. A hole is bored in the ground, typically, 150 to 250 feet deep (45–75 m). Pipe pairs in the hole are joined with a U-shaped cross connector at the bottom of the hole. The borehole is commonly filled with a bentonite grout surrounding the pipe to provide a good thermal connection to the surrounding soil or rock. Vertical loop fields are typically used when there is a limited square footage of land available. Bore holes are spaced 5–6 m apart and are generally 15 m (50 ft) deep per kW of cooling. During the cooling season, the local temperature rise in the bore field is influenced most by the moisture travel in the soil. Reliable heat transfer models have been developed through sample bore holes as well as other tests.

Horizontal closed loop field

A horizontal closed loop field is composed of pipes that run horizontally in the ground. A long horizontal trench, deeper than the frost line, is dug and U-shaped coils are placed horizontally inside the same trench. A trench for a horizontal loop field will be similar to one seen under the slinky loop field; however, the width strictly depends on how many loops are installed. Horizontal loop fields are very common and economical if there is adequate land available.

Slinky closed loop field

A slinky closed loop field is also installed in the horizontal orientation; however, the pipes overlay each other. The easiest way of picturing a slinky field is to imagine holding a slinky on the top and bottom with your hands and then move your hands in opposite directions. A slinky loop field is used if there is not adequate room for a true horizontal system, but it still allows for an easy installation. The image above shows a 3-ton slinky loop prior to being covered with soil. In the picture you can see the three slinky loops running out horizontally and three straight lines returning the end of the slinky coil to the heat pump.

Closed pond loop

A closed pond loop is not as common, but is becoming increasingly popular. A pond loop is achieved by placing coils of pipe at the bottom of an appropriately sized pond or water source. This system has been promoted by the DNR (Department of Natural Resources), who support geothermal systems and the use of ponds for geothermal systems. The two images below show a pond loop close up and the pond loop as it about to be sunk to the bottom of a pond. This loop field is for a 12-ton system, which is unusually large for most residential applications. As you can tell by the pictures; a pond loop is extremely similar to a slinky loop, except that it is attached to a frame and located in a body of water versus soil.

Open loop systems

In contrast to the closed loop systems, an open loop system pulls water directly from a well, lake, or pond. Water is pumped from one of these sources into the heat pump, where heat is either extracted or added. The water is then pumped back into a second well or source body of water. There are three general types of systems: First water can be pumped from a vertical water well and returned to a nearby pond. Second, water can pumped from a body of water and returned to the same body of water. Third, water can be pumped from a vertical well and then returned to the same well. While thermal contamination (where the ground temperature is effected by the operation of the system) is possible with any Geothermal system, with proper design, planning, and installation any loop configuration can work very well for a very long time. Deep lake water cooling uses a similar process with an open loop for air conditioning and cooling.

Standing Column Wells

Most common in areas where bedrock is within 150-200 feet of the surface. Water is drawn from the bottom of a deep rock well, passed through a heat pump, and returned to the top of the well, where traveling downwards exchanges heat with the surrounding bedrock. The choice of a Standing Column Well is often dictated by a large urban application or a rural application with an existing domestic water well.

Common heat pumps

Water-to-air heat pump

Water-to-water heat pump

There are also different types of water-source heat pumps. A variety of products are available, for both residential and commercial applications; there are water-to-air heat pumps, water-to-water heat pumps and hybrids between the two. Some manufactures are now producing a reversible heat pump for chillers also.

Water-to-air

The water-to-air heat pumps are designed to replace a forced air furnace and possibly the central air conditioning system. The term water-to-air signifies that the heat pump is designed for forced air applications and indicates that water is the source of heat. The water-to-air system is a single central unit that is capable of producing heat during the winter and air conditioning during the summer months. There are variations of the water-to-air heat pumps that allow for split systems, high-velocity systems, and ductless systems.

Water-to-water

A water-to-water heat pump is designed for a heating-system that utilizes hot water for heating the building. Systems such as radiant underfloor heating, baseboard radiators and conventional cast iron radiators would use a water-to-water heat pump. The water-to-water heat pump uses the warm water from the loop field to heat the water that is used for conditioning the structure. Just like a boiler, this heat pump is unable to provide air conditioning during the summer months.

Hybrid

A hybrid heat pump is capable of producing forced air heat and hot water simultaneously and individually. These systems are largely being used for houses that have a combination of under-floor and forced air heating. Both the water-to-water and hybrid heat pumps are capable of heating domestic water also. Almost all types of heat pumps are produced commercially and residentially for indoor and outdoor applications.

Water-source vs. Direct Exchange

While this article focuses on water-source systems in which the refrigerant exchanges its heat with a water loop that is placed in the ground, a direct exchange system (often known as DX) is one in which the refrigerant circulates through a copper pipe placed directly in the ground. This eliminates the need for a heat exchanger between the refrigerant loop and the water loop, as well as eliminating the water pump. These simpler systems are able to reach higher efficiencies while also requiring a shorter and smaller pipe to be placed in the ground, thus being less expensive to install. DX systems are a relatively newer technology than water-source.

DX systems, like water-source systems, can also be used to heat water in the house for use in radiant heating applications and for domestic hot water, as well as for cooling applications.

Benefits of Geothermal Heat Pumps

Geothermal systems are able to transfer heat to and from the ground with minimal use of electricity. When comparing a geothermal system to an ordinary system a homeowner can save anywhere from 30% to 70% annually on utilities. Even with the high initial costs of purchasing a geothermal system the payback period is relatively short, typically between three and five years. Geothermal systems are environmentally friendly; they are a renewable energy source, non-polluting, and recognized as one of the most efficient heating and cooling systems on the market.

The U.S. Environmental Protection Agency (EPA) has called geothermal the most energy-efficient, environmentally clean, and cost-effective space conditioning systems available. The life span of the system is longer than conventional heating and cooling systems. Most loop fields are warranted for 25 to 50 years and are expected to last at least 50 to 200 years. Geothermal systems do not use fossil fuels for heating the house and eliminate threats cause by combustion, like carbon monoxide poisoning. The fluids used in loop fields are designed to be biodegradable, non-toxic, non-corrosive and have properties that will minimize pumping power needed.

Some electric companies will offer special rates to customers that install geothermal systems for heating/cooling their building. This is due to the fact that heat pumps only use electricity for heating and no fossil fuels are being purchased. However, if the electricity comes from fossil fuel burning power plants this is no longer so. Renewable electricity such as a solar photo-voltaic system could be used to power the heat pumps. Electrical plants have the largest loads during summer months and much of their capacity sits idle during winter months. This allows the electric company to use more of their facility during the winter months and sell more electricity.

Geothermal eat pumps are especially well matched to underfloor heating systems which do not require extremely high temperatures (as compared with wall-mounted radiators). Thus they are ideal for open plan offices. Using large surfaces such as floors, as opposed to radiators, distributes the heat more uniformly and allows for a lower temperature heat transfer fluid.

The Earth below the frost line remains at a relatively constant temperature year round. This temperature equates roughly to the average annual air-temperature of the chosen location, so is usually 7-21 degrees Celsius (45-70 degrees Fahrenheit) depending on location. Because this temperature remains constant, geothermal heat pumps perform with far greater efficiency and in a far larger range of extreme temperatures than conventional air conditioners and furnaces, and even air-source heat pumps.

Geothermal heat pump technology is a Natural Building technique. It is also a practical heating and cooling solution that can pay for itself within a few years of installation.

Today there are more than 1,000,000 geothermal heat pump installations in the United States.

The current use of geothermal heat pump technology has resulted in the following emissions reductions:

• Elimination of more than 5.8 million metric tons of CO₂ annually
• Elimination of more than 1.6 million metric tons of carbon equivalent annually

These 1,000,000 installations have also resulted in the following energy consumption reductions:

• Annual savings of nearly 8,000 GWh
• Annual savings of nearly 40 trillion Btus of fossil fuels
• Reduced electricity demand by more than 2.6 GW

The impact of the current use of geothermal heat pumps is equivalent to:

• Taking close to 1,295,000 cars off the road
• Planting more than 385 million trees
• Reducing U.S. reliance on imported fuels by 21.5 million barrels (3,420,000 m³) of crude oil

per year.

Costs and savings

The initial cost of installing a geothermal heat pump system can be two to three times that of a conventional heating system in most residential applications, new construction or existing. In retrofits, the cost of installation is affected by the size of living area, the home's age, insulation characteristics, the geology of the area, and location of the home/property. For new construction, proper duct system design and mechanical air exchange should be considered in initial system cost. These systems can save the average family from 400-1400 US$/year, reducing the average heating/cooling costs by 35-70% per household. The cost of installation may be reduced by many governmental programs which all the home owners use to reduce their taxes at the end of the year.

See also

• Geothermal exchange heat pump
• Geothermal heating
• Earth cooling tubes
• Microgeneration Certification Scheme
• Geothermal heating
• Geothermal power

External links

• Geothermal Heat Pumps (US Department of Energy)
• GeoExchange Heating and Cooling Systems: Fascinating Facts
• Geothermal Heat Pump Consortium
• Canadian Geoexchange Coalition
• Ground Source Heat Pump Association - UK
• International Ground Source Heat Pump Association
• Fossil Freedom - Crash Course in geothermal heat pumps
• PATH Tech Inventory: Geothermal Heat Pumps
• US Dept. of Energy
• The RETScreen Ground-Source Heat Pump Project Model
• WaterFurnace- Equipment Manufacturer