Adit: Difference between revisions
Tag: section blanking |
|||
| Line 38: | Line 38: | ||
* A "level" is a horizontal passage that branches off from a shaft and is used for access to the parts of the mine where the ore is being removed. In mines where the lodes have significant vertical extent there can be many numbered levels, one below the other. They can be connected by short vertical shafts known as "[[winze]]s". A level that reaches the surface, on a hillside or in a valley, for instance, is called an "adit level". |
* A "level" is a horizontal passage that branches off from a shaft and is used for access to the parts of the mine where the ore is being removed. In mines where the lodes have significant vertical extent there can be many numbered levels, one below the other. They can be connected by short vertical shafts known as "[[winze]]s". A level that reaches the surface, on a hillside or in a valley, for instance, is called an "adit level". |
||
*"[[Sough]]" is a term mainly used in the [[Derbyshire lead mining history|lead mining areas of Derbyshire]]. The main purpose of a sough is to drain water from the mine. |
*"[[Sough]]" is a term mainly used in the [[Derbyshire lead mining history|lead mining areas of Derbyshire]]. The main purpose of a sough is to drain water from the mine. |
||
==Other meanings== |
|||
* Adit is a Sanskrit word which means beginning or first ray of sun. |
|||
==References== |
==References== |
||
Revision as of 14:08, 4 August 2012
An adit is an entrance to an underground mine which is horizontal or nearly horizontal,[1] by which the mine can be entered, drained of water,[2] and ventilated.
Construction
Adits are driven into the side of a hill or mountain, and are often used when an ore body is located inside the mountain but above the adjacent valley floor or coastal plain. In cases where the mineral vein outcrops at the surface, the adit may follow the lode or vein until it is worked out, in this case the adit is rarely straight. The use of adits for the extraction of ore is generally called drift mining.
Adits can only be driven into a mine where the local topography permits. There will be no opportunity to drive an adit to a mine situated on a large flat plain, for instance. Also if the ground is weak, the cost of shoring up a long adit may outweigh its possible advantages.
Access and ventilation
Access to a mine by adit has many advantages over the vertical access shafts used in shaft mining. Less energy is required to transport miners and heavy equipment into and out of the mine. It is also much easier to bring ore or coal out of the mine. Horizontal travel by means of narrow gauge tramway or cable car is also much safer and can move more people and ore than vertical elevators.
In combination with shafts, adits form an important element in the ventilation of a mine: in simple terms, cool air will enter through an adit, be warmed by the higher temperature underground and will naturally exhaust from vertical shafts,[citation needed] some of which are sunk specifically for this purpose and are known as "ventilation shafts".[3]
Drainage
Most adits are designed to slope slightly upwards from the entrance so that water will flow freely out of the mine.[4] Mines that have adits can be at least partly drained of water by gravity alone or power-assisted gravity. The depth to which a mine can be drained by gravity alone is defined by the deepest open adit which is known as the "drainage adit".[5] Workings above this level (known as "above adit") will remain unflooded as long as the adit does not become blocked. All mine workings below both the drainage adit ("below adit") and the water table will flood unless mechanical means are used for drainage. Until the invention of the steam engine this was the main restriction on deep mining. Of course, adits are still useful for deeper mines because the water only needs to be raised to the drainage adit rather than to the surface.
Because of the great reduction in ongoing costs that a drainage adit can provide, they have sometimes been driven for great distances just for this purpose, one such being the Milwr tunnel in North Wales, which is about ten miles (16 km) long. Another example is the Great County Adit in Cornwall, a 40-mile (64 km)-long network of adits that used to drain the whole Gwennap mining area. A side benefit of driving such extensive adits is that previously unknown ore-bodies can be discovered, helping finance the enormous cost.[5]
Adits were in use in Cornwall well before 1500 and were particularly important to the tin and copper mines in Cornwall and Devon because the ore-bearing veins here are near-vertical and act as channels through which water can easily seep.[4] There are many reports of torrents of warm or hot water continuously pouring into the lower levels of Cornish mines.[citation needed]
Notable examples
- Great County Adit, a system of nearly 40 miles (64 km) of adits used for dewatering the mines in the Gwennap area of Cornwall in the 18th and early 19th centuries.
- Milwr tunnel, a ten-mile (16 km)-long drainage adit in North Wales. Started in 1897, it still discharges an average of 23 million US gallons (87,000 m3) of water per day from the disused Halkyn District United Mines.
- The Snowy Hydro scheme in the Australian Snowy Mountains created during its construction. These adits are very large and used to access the central point from which the hydro tunnels were constructed.
- Black Trout Adit in Tarnowskie Góry, Poland. It is a part of former silver mine, the adit was used for removing the water out of the mine. It still carries water from old galleries to the nearest river, a part of it is open for tourists, who go 20m down the steps in one shaft, have a ride in a boat and go up the stairs in another shaft.
- Blue Hawk Mine near Kelowna, BC, Canada
- NORCAT's Underground Mine Centre (Fecunis Adit), used for underground training and mining technology development in Onaping, ON, Canada
Similar terms
- A "drift" is a more general term for any near-horizontal underground passage in a mine. Unlike an adit, a drift need not break out to the surface. Drift mining is the use of drifts to extract ore - in this case the drifts follow the vein.
- A "level" is a horizontal passage that branches off from a shaft and is used for access to the parts of the mine where the ore is being removed. In mines where the lodes have significant vertical extent there can be many numbered levels, one below the other. They can be connected by short vertical shafts known as "winzes". A level that reaches the surface, on a hillside or in a valley, for instance, is called an "adit level".
- "Sough" is a term mainly used in the lead mining areas of Derbyshire. The main purpose of a sough is to drain water from the mine.
References
- ^ Paul W. Thrush, 1968, A Dictionary of Mining, Mineral, and Related Terms, US Bureau of Mines, p.12.
- ^ R. W. Raymond, 1881, Glossary of Mining and Metallurgical Terms, American Institute of Mining Engineers, p.3.
- ^ Earl 1994, pp.64–65.
- ^ a b Earl 1994, p.36.
- ^ a b "Mining Encyclopaedia (Adit, Drainage Adit, Deep Drainage)". Mine-Explorer. Retrieved 2010-12-06.
Sources
- Earl, Bryan (1994). Cornish Mining: The Techniques of Metal Mining in the West of England, Past and Present (2nd ed.). St Austell: Cornish Hillside Publications. ISBN 0-9519419-3-3.