Jump to content

Lift-to-drag ratio

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by 95.91.246.145 (talk) at 08:16, 24 December 2021 (→‎Glide ratio: +link). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Coefficients of drag CD and lift CL vs angle of attack.

In aerodynamics, the lift-to-drag ratio (or L/D ratio) is the lift generated by a wing or vehicle, divided by the aerodynamic drag caused by moving through air. It describes the quantity of the aerodynamic efficiency. The L/D ratio can theoretically given at any three-dimensional airspeed or acceleration based on the balance of forces. If not specified, it is given for a not accelerated, even level flight or an unpowered glide, in which it is equal to the glide ratio.

The L/D ratio is inversely proportional to the needed energy for a given aircraft – meaning that double L/D ratio requires only half of the energy for the same flight length. This results directly to better fuel economy in aircraft. In wing design, better L/D ratio can also be achieved by increasing the aspect ratio, lowering the lift-induced drag.

The term is calculated for any particular airspeed by measuring the lift generated, then dividing by the drag at that speed. These vary with speed, so the results are typically plotted on a 2-dimensional graph. In almost all cases the graph forms a U-shape, due to the two main components of drag.

Lift-to-drag ratios can be determined by flight test, by calculation, computer simulation or by testing in a wind tunnel.[1][2][3]

Drag

Drag vs Speed. L/DMAX occurs at minimum Total Drag (e.g. Parasite plus Induced)
Polar curve showing glide angle for the best glide speed (best L/D). It is the flattest possible glide angle through calm air, which will maximize the distance flown. This airspeed (vertical line) corresponds to the tangent point of a line starting from the origin of the graph. A glider flying faster or slower than this airspeed will cover less distance before landing.[4][5]

Lift-induced drag is a component of total drag that occurs whenever a finite span wing generates lift. At low speeds an aircraft has to generate lift with a higher angle of attack, thereby resulting in a greater induced drag. This term dominates the low-speed side of the graph of lift versus velocity.

Drag curve for light aircraft. The tangent gives the maximum L/D point.

Form drag is caused by movement of the aircraft through air. This type of drag, known also as air resistance or profile drag varies with the square of speed (see drag equation). For this reason profile drag is more pronounced at greater speeds, forming the right side of the lift/velocity graph's U shape. Profile drag is lowered primarily by streamlining and reducing cross section.

Lift, like drag, increases as the square of the velocity and the ratio of lift to drag is often plotted in terms of the lift and drag coefficients CL and CD. Such graphs are referred to as drag curves. Speed increases from left to right. The lift/drag ratio is given by the slope from the origin to some point on this curve and so the maximum L/D ratio does not occur at the point of least drag, the leftmost point. Instead it occurs at a slightly greater speed. Designers will typically select a wing design which produces an L/D peak at the chosen cruising speed for a powered fixed-wing aircraft, thereby maximizing economy. Like all things in aeronautical engineering, the lift-to-drag ratio is not the only consideration for wing design. Performance at a high angle of attack and a gentle stall are also important.

Glide ratio

See also: Gliding_(flight) § Glide_ratio

As the aircraft fuselage and control surfaces will also add drag and possibly some lift, it is fair to consider the L/D of the aircraft as a whole. As it turns out, the glide ratio, which is the ratio of an (unpowered) aircraft's forward motion to its descent, is (when flown at constant speed) numerically equal to the aircraft's L/D. This is especially of interest in the design and operation of high performance sailplanes, which can have glide ratios almost 60 to 1 (60 units of distance forward for each unit of descent) in the best cases, but with 30:1 being considered good performance for general recreational use. Achieving a glider's best L/D in practice requires precise control of airspeed and smooth and restrained operation of the controls to reduce drag from deflected control surfaces. In zero wind conditions, L/D will equal distance traveled divided by altitude lost. Achieving the maximum distance for altitude lost in wind conditions requires further modification of the best airspeed, as does alternating cruising and thermaling. To achieve high speed across country, glider pilots anticipating strong thermals often load their gliders (sailplanes) with water ballast: the increased wing loading means optimum glide ratio at greater airspeed, but at the cost of climbing more slowly in thermals. As noted below, the maximum L/D is not dependent on weight or wing loading, but with greater wing loading the maximum L/D occurs at a faster airspeed. Also, the faster airspeed means the aircraft will fly at greater Reynolds number and this will usually bring about a lower zero-lift drag coefficient.

Theory

Mathematically, the maximum lift-to-drag ratio can be estimated as:

[6]

where AR is the aspect ratio, the span efficiency factor, a number less than but close to unity for long, straight edged wings, and the zero-lift drag coefficient.

Most importantly, the maximum lift-to-drag ratio is independent of the weight of the aircraft, the area of the wing, or the wing loading.

It can be shown that two main drivers of maximum lift-to-drag ratio for a fixed wing aircraft are wingspan and total wetted area. One method for estimating the zero-lift drag coefficient of an aircraft is the equivalent skin-friction method. For a well designed aircraft, zero-lift drag (or parasite drag) is mostly made up of skin friction drag plus a small percentage of pressure drag caused by flow separation. The method uses the equation:

[7]

where is the equivalent skin friction coefficient, is the wetted area and is the wing reference area. The equivalent skin friction coefficient accounts for both separation drag and skin friction drag and is a fairly consistent value for aircraft types of the same class. Substituting this into the equation for maximum lift-to-drag ratio, along with the equation for aspect ratio (), yields the equation:

where b is wingspan. The term is known as the wetted aspect ratio. The equation demonstrates the importance of wetted aspect ratio in achieving an aerodynamically efficient design.

Supersonic/hypersonic lift to drag ratios

At very great speeds, lift to drag ratios tend to be lower. Concorde had a lift/drag ratio of about 7 at Mach 2, whereas a 747 is about 17 at about mach 0.85.

Dietrich Küchemann developed an empirical relationship for predicting L/D ratio for high Mach:[8]

where M is the Mach number. Windtunnel tests have shown this to be approximately accurate.

Examples of L/D ratios

Computed aerodynamic characteristics[16]
Jetliner cruise L/D First flight
L1011-100 14.5 Nov 16, 1970
DC-10-40 13.8 Aug 29, 1970
A300-600 15.2 Oct 28, 1972
MD-11 16.1 Jan 10, 1990
B767-200ER 16.1 Sep 26, 1981
A310-300 15.3 Apr 3, 1982
B747-200 15.3 Feb 9, 1969
B747-400 15.5 Apr 29, 1988
B757-200 15.0 Feb 19, 1982
A320-200 16.3 Feb 22, 1987
A310-300 18.1 Nov 2, 1992
A340-200 19.2 Apr 1, 1992
A340-300 19.1 Oct 25, 1991
B777-200 19.3 Jun 12, 1994

See also

References

[13]

  1. ^ Accurate calculation of aerodynamic coefficients of parafoil airdrop system based on computational fluid dynamic Wannan Wu , Qinglin Sun, Shuzhen Luo, Mingwei Sun, Zengqiang Chen and Hao Sun: International Journal of Advanced Robotic Systems
  2. ^ Validation of software for the calculation of aerodynamic coefficientsaerodynamic coefficientsaerodynamic coefficientsaerodynamic coefficients Ramón López Pereira, Linköpings Universitet
  3. ^ In-flight Lift and Drag Estimation of an Unmanned Propeller-Driven Aircraft Dominique Paul Bergmann, Jan Denzel, Ole Pfeifle, Stefan Notter, Walter Fichter and Andreas Strohmayer
  4. ^ Wander, Bob (2003). Glider Polars and Speed-To-Fly...Made Easy!. Minneapolis: Bob Wander's Soaring Books & Supplies. p. 7-10.
  5. ^ Glider Flying Handbook, FAA-H-8083-13. U.S. Department of Transportation, FAA. 2003. p. 5-6 to 5-9. ISBN 9780160514197.
  6. ^ Loftin, LK Jr. "Quest for performance: The evolution of modern aircraft. NASA SP-468". Retrieved 2006-04-22.
  7. ^ Raymer, Daniel (2012). Aircraft Design: A Conceptual Approach (5th ed.). New York: AIAA.
  8. ^ Aerospaceweb.org Hypersonic Vehicle Design
  9. ^ Antonio Filippone. "Lift-to-Drag Ratios". Advanced topics in aerodynamics. Archived from the original on March 28, 2008.
  10. ^ Cumpsty, Nicholas (2003). Jet Propulsion. Cambridge University Press. p. 4.
  11. ^ Christopher Orlebar (1997). The Concorde Story. Osprey Publishing. p. 116. ISBN 9781855326675.[permanent dead link]
  12. ^ Leishman, J. Gordon (24 April 2006). Principles of helicopter aerodynamics. Cambridge University Press. p. 230. ISBN 0521858607. The maximum lift-to-drag ratio of the complete helicopter is about 4.5
  13. ^ a b Cessna Skyhawk II Performance Assessment http://temporal.com.au/c172.pdf
  14. ^ "U2 Developments transcript". Central Intelligence Agency. 1960. {{cite web}}: Unknown parameter |lay-source= ignored (help); Unknown parameter |lay-url= ignored (help)
  15. ^ David Noland (February 2005). "The Ultimate Solo". Popular Mechanics.
  16. ^ Rodrigo Martínez-Val; et al. (January 2005). "Historical evolution of air transport productivity and efficiency". 43rd AIAA Aerospace Sciences Meeting and Exhibit. doi:10.2514/6.2005-121.[permanent dead link]

External links

Retrieved from "https://en.wikipedia.org/w/index.php?title=Lift-to-drag_ratio&oldid=1061835401"