Flywheel
![](http://upload.wikimedia.org/wikipedia/commons/thumb/6/68/Thinktank_Birmingham_-_Trevithick_Locomotive%281%29.jpg/220px-Thinktank_Birmingham_-_Trevithick_Locomotive%281%29.jpg)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/2/2f/G2_front2.jpg/220px-G2_front2.jpg)
![](http://upload.wikimedia.org/wikipedia/commons/b/ba/Spoked_flywheel_animation.gif)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/9/9c/Volin.jpg/220px-Volin.jpg)
A flywheel is a mechanical device specifically designed to efficiently store rotational energy. Flywheels resist changes in rotational speed by their moment of inertia. The amount of energy stored in a flywheel is proportional to the square of its rotational speed. The way to change a flywheel stored energy is by increasing or decreasing its rotational speed applying a torque aligned with its axis of symmetry,
Common uses of a flywheel include:
- Smoothing the power output of an energy source. For example flywheels are used in reciprocating engines because the active torque from the individual pistons is intermittent.
- Energy storage systems Flywheel energy storage
- Delivering energy at rates beyond the ability of an energy source. This is achieved by collecting energy in a flywheel over time and then releasing it quickly, at rates that exceed the abilities of the energy source.
- Controlling the orientation of a mechanical system, gyroscope and reaction wheel
Flywheels are typically made of steel and rotate on conventional bearings; these are generally limited to a maximum revolution rate of a few thousand RPM.[1] High energy density flywheels can be made of carbon fiber composites and employ magnetic bearings, enabling them to revolve at speeds up to 60,000 RPM (1 kHz).[2]
Carbon-composite flywheel batteries have recently been manufactured and are proving to be viable in real-world tests on mainstream cars. Additionally, their disposal is more eco-friendly.[3]
Applications
Flywheels are often used to provide continuous power output in systems where the energy source is not continuous. For example, a flywheel is used to smooth fast angular velocity fluctuations of the crankshaft in a reciprocating engine. In this case, a crankshaft flywheel stores energy when torque is exerted on it by a firing piston, and returns it to the piston to compress a fresh charge of air and fuel. Another example is the friction motor which powers devices such as toy cars. In unstressed and inexpensive cases to save on cost the bulk of the mass of the flywheel is toward the rim of the wheel. Pushing the mass away from the axis of rotation heightens rotational inertia for a given total mass.
![](http://upload.wikimedia.org/wikipedia/commons/5/56/P307.jpg)
A flywheel may also be used to supply intermittent pulses of energy at power levels that exceed the abilities of its energy source. This is achieved by accumulating energy in the flywheel over a period of time, at a rate that is compatible with the energy source, and then releasing energy at a much higher rate over a relatively short time when it is needed. For example flywheels are used in power hammers and riveting machines. Flywheels can be used to control direction and oppose unwanted motions, see gyroscope. Flywheels in this context have a wide range of applications from gyroscopes for instrumentation to ship stability and satellite stabilization (reaction wheel), to keep a toy spin spinning (friction motor), to stabilize magnetically levitated objects (Spin-stabilized magnetic levitation)
History
The principle of the flywheel is found in the Neolithic spindle and the potter's wheel.[4]
The use of the flywheel as a general mechanical device to equalize the speed of rotation is, according to the American medievalist Lynn White, recorded in the De diversibus artibus (On various arts) of the German artisan Theophilus Presbyter (ca. 1070–1125) who records applying the device in several of his machines.[4][5]
In the Industrial Revolution, James Watt contributed to the development of the flywheel in the steam engine, and his contemporary James Pickard used a flywheel combined with a crank to transform reciprocating motion into rotary motion.
Physics
A flywheel is a spinning wheel, or disc, or rotor, rotating around its symmetry axis. Energy is stored as kinetic energy, more specifically rotational energy, of the rotor :
where:
- ω is the angular velocity, and
- is the moment of inertia of the flywheel about its axis of cylindrical symmetry. The moment of inertia is a measure of resistance to torque applied on a spinning object (i.e. the higher the moment of inertia, the slower it will accelerate when a given torque is applied).
- The moment of inertia for a solid cylinder is ,
- for a thin-walled empty cylinder is ,
- and for a thick-walled empty cylinder is ,[6]
where m denotes mass, and r denotes a radius.
When calculating with SI units, the units would be for mass, kilograms; for radius, meters; and for angular velocity, radians per second and the resulting energy would be in joules.
Increasing amounts of rotation energy can be stored in the flywheel until the rotor shatters. The hoop stress that develops within the rotor is a major consideration in the design of a flywheel energy storage system.
where:
- is the tensile stress on the rim of the cylinder
- is the density of the cylinder
- is the radius of the cylinder, and
- is the angular velocity of the cylinder.
This formula can also be simplified using specific tensile strength and tangent velocity:
where:
- is the specific tensile strength of the material
- is the tangent velocity of the rim.
Material selection
Flywheels are made from many different materials; the demands of the application determine the choice of material. Small flywheels made of lead are found in children’s toys. Cast iron flywheels are used in old steam engines. Flywheels used in cars to smooth power-transmission may be made of cast or nodular iron, steel or aluminum depending on the performance application.[7] Flywheels made from high-strength steel or composites have been proposed for use in vehicle power storage and braking systems.
The efficiency of a flywheel is determined by the maximum amount of energy it can store per unit weight. As the flywheel’s rotational speed or angular velocity is increased, the stored energy increases; however, the centrifugal stresses also increase. If the centrifugal stresses surpass the tensile strength of the material, the flywheel will break apart. Thus, the tensile strength determines an upper limit to the amount of energy that a flywheel can store.
In this context, using lead for a flywheel in a child’s toy is not efficient; however, the flywheel velocity never approaches its burst velocity because the limit in this case is the pulling-power of the child. In other applications, such as an automobile, the flywheel operates at a specified angular velocity and is constrained by the space it must fit in, so the goal is to maximize the stored energy per unit volume. The material selection therefore depends on the application.[8]
The table below contains calculated values for materials and comments on their viability for flywheel applications. CFRP stands for carbon-fiber-reinforced polymer, and GFRP stands for glass-fiber reinforced polymer.
Material | Specific tensile strength | Comments |
---|---|---|
Ceramics | 200-2000 (compression only) | Brittle and weak in tension, therefore eliminate |
Composites: CFRP | 200-500 | The best performance—a good choice |
Composites: GFRP | 100-400 | Almost as good as CFRP and cheaper |
Beryllium | 300 | The best metal, but expensive, difficult to work with, and toxic to machine |
High strength steel | 100-200 | Cheaper than Mg and Ti alloys |
High strength Al alloys | 100-200 | Cheaper than Mg and Ti alloys |
High strength Mg alloys | 100-200 | About equal performance to steel and Al-alloys |
Ti alloys | 100-200 | About equal performance to steel and Al-alloys |
Lead alloys | 3 | Very low |
Cast Iron | 8-10 | Very low[9] |
The table below shows calculated values for mass, radius, and angular velocity for storing 500 J. The carbon-fiber flywheel is by far the most efficient; however, it also has the largest radius. In applications (like in an automobile) where the volume is constrained, a carbon-fiber flywheel might not be the best option.
Material | Energy storage (J) | Mass (kg) | Radius (m) | Angular velocity (rpm) | Efficiency (J/kg) | Energy density (kWh/kg) |
---|---|---|---|---|---|---|
Cast Iron | 500 | 0.0166 | 1.039 | 1465 | 30121 | 0.0084 |
Aluminum Alloy | 500 | 0.0033 | 1.528 | 2406 | 151515 | 0.0421 |
Maraging steel | 500 | 0.0044 | 1.444 | 2218 | 113636 | 0.0316 |
Composite: CFRP (40% epoxy) | 500 | 0.001 | 1.964 | 3382 | 500000 | 0.1389 |
Composite: GFRP (40% epoxy | 500 | 0.0038 | 1.491 | 2323 | 131579[10] | 0.0365 |
Table of energy storage traits
Flywheel purpose, type | Geometric shape factor (k) (unitless – varies with shape) |
Mass (kg) |
Diameter (cm) |
Angular velocity (rpm) |
Energy stored (MJ) |
Energy stored (kWh) |
Energy density (kWh/kg) |
---|---|---|---|---|---|---|---|
Small battery | 0.5 | 100 | 60 | 20,000 | 9.8 | 2.7 | 0.027 |
Regenerative braking in trains | 0.5 | 3000 | 50 | 8,000 | 33.0 | 9.1 | 0.003 |
Electric power backup[11] | 0.5 | 600 | 50 | 30,000 | 92.0 | 26.0 | 0.043[12][13][14][15] |
For comparison, the energy density of petrol (gasoline) is 44.4 MJ/kg or 12.3 kWh/kg.
High-energy materials
For a given flywheel design, the kinetic energy is proportional to the ratio of the hoop stress to the material density and to the mass:
could be called the specific tensile strength. The flywheel material with the highest specific tensile strength will yield the highest energy storage per unit mass. This is one reason why carbon fiber is a material of interest.
For a given design the stored energy is proportional to the hoop stress and the volume:
Rimmed
A rimmed flywheel has a rim, a hub, and spokes.[16] Calculation of the flywheel's moment of inertia can be more easily analysed by applying various simplifications. For example:
- Assume the spokes, shaft and hub have zero moments of inertia, and the flywheel's moment of inertia is from the rim alone.
- The lumped moments of inertia of spokes, hub and shaft may be estimated as a percentage of the flywheel's moment of inertia, with the majority from the rim, so that
For example, if the moments of inertia of hub, spokes and shaft are deemed negligible, and the rim's thickness is very small compared to its mean radius (), the radius of rotation of the rim is equal to its mean radius and thus:
See also
- Dual mass flywheel
- Flywheel energy storage
- Diesel rotary uninterruptible power supply
- List of moments of inertia
- Clutch
References
- ^ [1]; "Flywheels move from steam age technology to Formula 1"; Jon Stewart | 1 July 2012, retrieved 2012-07-03
- ^ [2], "Breakthrough in Ricardo Kinergy ‘second generation’ high-speed flywheel technology"; Press release date: 22 August 2011. retrieved 2012-07-03
- ^ http://www.popularmechanics.com/technology/engineering/news/10-tech-concepts-you-need-to-know-for-2012-2
- ^ a b Lynn White, Jr., "Theophilus Redivivus", Technology and Culture, Vol. 5, No. 2. (Spring, 1964), Review, pp. 224–233 (233)
- ^ Lynn White, Jr., "Medieval Engineering and the Sociology of Knowledge", The Pacific Historical Review, Vol. 44, No. 1. (Feb., 1975), pp. 1–21 (6)
- ^ [3] (page 10, accessed 1 Dec 2011, Moment of inertia tutorial
- ^ "Flywheels: Iron vs. Steel vs. Aluminum". Fidanza Performance. Retrieved 6 October 2016.
- ^ Ashby, Michael (2011). Materials Selection in Mechanical Design (4th ed.). Burlington, MA: Butterworth-Heinemann. pp. 142–146. ISBN 978-0-08-095223-9.
- ^ Totten, George E.; Xie, Lin; Funatani, Kiyoshi (2004). Handbook of Mechanical Alloy Design. New York: Marcel Dekker. ISBN 0-8247-4308-3.
- ^ Kumar, Mouleeswaran Senthil; Kumar, Yogesh (2012). "Optimization of Flywheel Materials Using Genetic Algorithm" (PDF). Acta technica Corviniensis-Bulletin of Engineering. Retrieved 1 November 2015.
- ^ https://www.calnetix.com/vdc-kinetic-energy-storage-systems
- ^ "Flywheel Energy Calculator". Botlanta.org. 2004-01-07. Retrieved 2010-11-30.
- ^ "energy buffers". Home.hccnet.nl. Retrieved 2010-11-30.
- ^ "Message from the Chair | Department of Physics | University of Prince Edward Island". Upei.ca. Retrieved 2010-11-30.
- ^ "Density of Steel". Hypertextbook.com. 1998-01-20. Retrieved 2010-11-30.
- ^ Flywheel Rotor And Containment Technology Development, FY83. Livermore, Calif: Lawrence Livermore National Laboratory , 1983. pp. 1–2
External links
![](http://upload.wikimedia.org/wikipedia/commons/thumb/9/99/Wiktionary-logo-en-v2.svg/40px-Wiktionary-logo-en-v2.svg.png)
![](http://upload.wikimedia.org/wikipedia/en/thumb/4/4a/Commons-logo.svg/30px-Commons-logo.svg.png)
- Flywheel batteries on Interesting Thing of the Day.
- Flywheel-based microgrid stabilisation technology., ABB
- PowerStore