Jump to content

Coherent optical module

Add links
From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Jim Dixon 55104 (talk | contribs) at 00:34, 12 August 2023. The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Coherent optical module refers to a typically hot-pluggable coherent optical transceiver that uses coherent modulation (BPSK/QPSK/QAM) rather than amplitude modulation (RZ/NRZ/PAM4) and is typically used in high-bandwidth data communications applications. Optical modules typically have an electrical interface on the side that connects to the inside of the system and an optical interface on the side that connects to the outside world through a fiber optic cable. The technical details of coherent optical modules were proprietary for many years, but have recently attracted efforts by multi-source agreement (MSA) groups and a standards development organizations such as the Optical Internetworking Forum. Coherent optical modules can either plug into a front panel socket or an on-board socket. Coherent optical modules form a smaller piece of a much larger optical module industry.

Electrical Interface Types

There are multiple variants of the electrical interface of coherent optical modules use.

Analog Coherent Optics (ACO)

The Optical Internetworking Forum in 2016 published the CFP2-ACO or CFP2 - Analog Coherent Optics Module Interoperability Agreement (IA). This IA supports a configuration where the digital signal processor (DSP) is on the main board and analog optical components are on the module. This IA is useful in the case when the DSP exceeds the module power envelope.[1] The ACO interface can be used in coherent optics applications when the link delivers a flexible amount of bandwidth to the system, for example when combined with FlexE. The initial ACO IA is for the CFP2 module. The typical optical modulations that are used include Dual Polarization Quadrature Phase Shift Keying (DP-QPSK) and Quadrature Amplitude Modulation QAM-16.

Digital Coherent Optics (DCO)

These modules put the DSP on the module and use a conventional retimed digital interface. These modules can use the same optical modulation techniques as the ACO interfaces do.

Optical modulation and multiplexing types

Many different forms of optical modulation and multiplexing have been employed in coherent optical modules.

NRZ and PAM-4 modulation

Some coherent optical modules can fall back to older, simpler modulation techniques such as on-off keying (NRZ) and/or Pulse-amplitude modulation with 4 levels (PAM-4) when appropriate. This is used, for example, when it is discovered that the module on the other end of the link does not support coherent modulation.

Coherent modulation

Techniques include Dual Polarization Quadrature Phase Shift Keying (DP-QPSK) and QAM-16.

Tunable optical frequency

Tunable lasers are sometimes used in combination with coherent modulation to allow a module to support various forms of network-based optical switching such as needed in certain cases by an optical mesh networks or a Reconfigurable optical add-drop multiplexer (ROADM). In these, the transmit laser can be tuned to a different optical frequency/wavelength. Similarly the receiver is able to receive different optical frequencies.

Lambda multiplexing

Different optical wavelengths, also referred to as lambdas, of light are multiplexed within some coherent optical modules using wavelength-division multiplexing (WDM). Variants include Coarse WDM (CWDM), Dense WDM (DWDM).

In-module components

Coherent optical modules have a series of components inside, some of which have received attention from standards development organizations.

In-module gearbox

In many cases, the baud rate of the coherent optical interface does not equal the baud rate of the electrical interface. In these cases, a "gearbox" may be used within the module to convert between the rates. Because coherent modules typically have Digital Signal Processors, these gearbox functions sometimes are implemented in firmware.

In-module forward error correction

Particularly in the long-reach module market, in-module Forward Error Correction (FEC) has been included. This has been in both proprietary and standards-based forms. Coherent optical modules sometimes have used soft-decision decoder FEC algorithms

In-module optical transceiver implementation agreements

The OIF has created interoperability agreements to create multi-vendor interoperability for a series of in-module components, particularly focused on coherent transmission. These have included

  • High Bandwidth Integrated Polarization Multiplexed Quadrature Modulators[2]
  • Integrated Polarization Multiplexed Quadrature Modulated Transmitters[3]
  • Integrated Dual Polarization Micro-Intradyne Coherent Receivers[4]

In-module tunable laser implementation agreements

The OIF has created interoperability agreements to create multi-vendor interoperability for the tunable lasers that are sometimes used in optical modules. These have included

  • Integrable Tunable Laser Assembly Multi Source Agreement[5]
  • Micro Integrable Tunable Laser Assembly Implementation Agreement [6]

Front panel optical module MSAs

Several Multi-source agreements (MSAs) have coherent optical modules.

QSFP family front-panel modules

CFP family front-panel modules

The C form-factor pluggable (CFP) is an MSA among competing manufacturers for a common form-factor for the transmission of high-speed digital signals.

On-Board Optical module MSAs

Some pluggable modules fit on top of the printed circuit board instead of on the front panel.

CFP family on-board modules

Users of Coherent optical Modules

Long-haul Optical Transport Network (OTN) networks were the traditional users of coherent modulation. Cloud scale data centers have become an important consumer of coherent optical modules, particularly in the Ethernet connectivity space for reaches greater than 10 km where the advantages of coherent modulation can outweigh the increased cost.

Optical module focused trade shows

OFC Logo blue July 2014

The main trade show for the coherent optical module industry is the Optical Fiber Conference (OFC), that is held annually in southern California. Other prominent shows for the industry include ECOC in Europe and FOE in Japan.

References

  1. ^ "OIF-CFP2-ACO-01.0" (PDF). 2016-01-22. Archived from the original (PDF) on 2017-12-15. Retrieved 2017-05-08.
  2. ^ "Implementation Agreement for High Bandwidth Integrated Polarization Multiplexed Quadrature Modulators" (PDF). 2017-01-19. Retrieved 2017-07-20.
  3. ^ "Implementation Agreement for Integrated Polarization Multiplexed Quadrature Modulated Transmitters" (PDF). 2015-05-15. Archived from the original (PDF) on 2016-10-20. Retrieved 2017-07-20.
  4. ^ "Implementation Agreement for Integrated Dual Polarization Micro-Intradyne Coherent Receivers" (PDF). 2015-03-31. Archived from the original (PDF) on 2017-10-31. Retrieved 2017-07-20.
  5. ^ "Integrable Tunable Laser Assembly MultiSource Agreement" (PDF). 2015-07-13. Archived from the original (PDF) on 2017-11-07. Retrieved 2017-07-21.
  6. ^ "IMicro Integrable Tunable Laser Assembly Implementation Agreement 2015-07-13" (PDF). Archived from the original (PDF) on 2016-08-04. Retrieved 2017-07-21.
  7. ^ SFF Committee (November 2006). QSFP Public Specification (PDF) (Report). 1.0. SFF Committee. p. 12. INF-8438i.
  8. ^ SFF Committee (29 June 2015). QSFP+ 28 Gb/s 4X Pluggable Transceiver Solution (Report). 1.9. p. 5. SFF-8665.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Coherent_optical_module&oldid=1169897727"