Jump to content

Instrument landing system localizer

From Wikipedia, the free encyclopedia
(Redirected from Localizer antenna)
Localizer as component of an ILS (KMEZ runway 27, Mena, Arkansas)
Emission patterns of the localizer and glide path signals

An instrument landing system localizer, or simply localizer (LOC,[1] or LLZ prior to 2007[2]), is a system of horizontal guidance in the instrument landing system, which is used to guide aircraft along the axis of the runway.

Principle of operation

[edit]

In aviation, a localizer is the lateral component of the instrument landing system (ILS) for the runway centerline when combined with the vertical glide path, not to be confused with a locator, although both are parts of aviation navigation systems.

A localizer (like a glide path) requires both a transmitting airport runway system and receiving cockpit instruments. An older aircraft without an ILS receiver cannot take advantage of any ILS facilities at any runway, and much more importantly, the most modern aircraft have no use of their ILS instruments at runways which lack ILS facilities. In parts of Africa and Asia large airports may lack any kind of transmitting ILS system. Some runways have ILS only in one direction; this can still be used for horizontal centering when landing the opposite direction (with lower precision) and is known as the back beam or back course.

Two signals are transmitted on one of 40 ILS channels. One is amplitude modulated at 90 Hz, the other at 150 Hz. These are transmitted from co-located phased array antenna elements. Each antenna transmits a narrow beam. In addition, a clearing signal is transmitted at one tenth of the power with a wider beam to prevent receivers from picking up the side lobes of the main beam.

The signals' phases at the antenna elements are arranged such that the 150 Hz signal is more prominent (has a greater depth of modulation) at a receiver located to the right of centerline, and the 90 Hz signal is more prominent to the left. The cockpit instrument uses the difference between the modulation strengths of the two received signals to indicate left or right deviation from centerline.

Carrier frequency pairings

[edit]

Localizer (LOC) and glide path (G/P) (a.k.a. glide slope [G/S]) carrier frequencies are paired so that the navigation radio automatically tunes the G/S frequency which corresponds to the selected LOC frequency. The LOC signal is in the 110 MHz range while the G/S signal is in the 330 MHz range.[3]

LOC carrier frequencies range between 108.10 MHz and 111.95 MHz (with the 100 kHz first decimal digit always odd, so 108.10, 108.15, 108.30, etc., are LOC frequencies and are not used for any other purpose).[3]

Localizer in cockpit

[edit]
An attitude indicator (AI), more commonly known as an artificial horizon. The localizer is shown on the scale below the attitude gauge, and is in this case looking almost as a small white "^" sign. Both the indicator and its scale are small.

The localizer indicator is (on most aircraft manufactured from the late 1950s) shown below the Attitude Indicator, but is still a part of this instrument together with the glide path indicator and the cross in the center of the instrument which is called flight director.

The glide path scale is located to the right of the attitude sphere. On aircraft which have a mechanical gyro compass are both the localizer and glide path indicated as a vertical and a horizontal arrow in the compass as well. But they are essentially read in the same way. On some aircraft is only the glide path indicated on two main instruments, and the oldest version of ILS-instruments was an instrument of its own used instead. This used two dangling bars, fixed in the middle of the top (localizer indicator) and in the middle of the left side (glide path indicator), and if the aircraft was located on the intended glide path, the dangling bars formed a cross. This is, in theory, however, more difficult to learn—but even for pilots experienced with using such indicators, it added another instrument they needed to focus on. With the indicators added to the artificial horizon (and to the compass), the pilot can theoretically watch the attitude simultaneously with the localizer and glide path.

In modern cockpits, the localizer is seen as a colored dot (usually in the shape of a diamond) at the bottom of the artificial horizon. It does not appear during cruise, but comes up during the descent and approach to the selected runway, provided that the navigation radio is set to the ILS frequency of that specific runway. If the transmitted localizer beam, which usually, but not always, is directed in the heading of the runway extension (exceptions exist, for instance, in Innsbruck, Austria and in Macao). If the aircraft is located on this line, the localizer dot will appear in the middle of the scale. But if the aircraft is located a little left of the beam, the marker will appear to the right on the localizer gauge scale in cockpit. The pilot then knows he or she must adjust the heading towards the dot.

In older cockpits, the localizer scale below the artificial horizon is rather short. But in older style cockpit instrumentation, the localizer also appears as an arrow in the gyro compass below the artificial horizon. The top and bottom of this arrow "is one unit", which shows current heading. But the middle part of this arrow is moving independently of the aircraft's heading. The middle of that arrow could be described as being "stand alone", and moves to the left if the aircraft is located to the right of localizer beam and to the right if the aircraft is located to the left of the localizer beam. When the arrow is "united" to a straight line, then the aircraft is following the localizer beam. (This second "arrow-indicator" is omitted in modern cockpits, but the main compass is still located below the artificial horizon.)

The very first generation of localizer gauges had a different cockpit interface, and were not included in the artificial horizon nor any compass, but at a gauge of its own. The localizer was then represented as a dangling stick hanging from a fixed point at the top of a separate gauge, and the glide path was represented by a similar, but horizontal, dangling stick, fixed at one of the sides of the gauge. When the aircraft was located exactly at the ILS-beam (or glide path) the two sticks formed a cross. This interface resembles the flight director, which also forms a cross, but on the artificial horizon. This older ILS instrumentation system was omitted around the same time as jet airliners like Boeing 707 and DC 8 were introduced.

The expression "catch the localizer" refers to runway approaches with the autopilot engaged. The angle between the aircraft heading and localizer beam should be less than 30 degrees, and the indicated airspeed at least below 250 knots (for jet airliners), then by pushing a button marked "APP" or "ILS", then the autopilot presumably will turn and then follow the localizer. The autopilot will then also automatically descend according to the glide path. Normal procedure is to capture the localizer first and then follow the glide path as well. If the angle is too large or the airspeed too high, capturing the localizer may be unsuccessful.

The cockpit ILS indicators are not to be confused with the flight director, which also places vertical and horizontal lines on the artificial horizon. A flight director only shows how the autopilot would fly. If the localizer dot (or arrow) indicate runway is to be found to the left, but the flight director suggests a right turn, and the runway is not visible, then the pilot in command is having difficulties.

Localizer at runways

[edit]
Limits of localizer coverage

When the glide path is unserviceable, the localizer element can often be conducted as a separate non-precision approach; or a standalone instrument approach installation without an associated glide path, both are abbreviated as 'LOC' (or 'LLZ' prior to 2007.)

See also

[edit]

References

[edit]
  1. ^ ICAO Abbreviations and Codes (DOC 8400) (Report) (9th ed.). International Civil Aviation Organization. 2016.
  2. ^ ICAO Abbreviations and Codes (DOC 8400) (Report) (6th ed.). International Civil Aviation Organization. 2004.
  3. ^ a b "Frequency Allotments" (PDF). NTIA.DOC.gov. January 2008. Archived from the original (PDF) on 2010-08-28. Retrieved 2022-06-26.