Jump to content

Machine head

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Andy Dingley (talk | contribs) at 23:07, 4 June 2017 (Clearer masthead). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Open worm type machine head on a ukulele
For other uses, see Machine head (disambiguation).

A machine head (also referred to as a tuning machine, tuner, or gear head) is a geared apparatus for tuning stringed musical instruments by adjusting string tension. Machine heads are used on mandolins, guitars, double basses etc., and are usually located on the instrument's headstock. Non-geared tuning devices that are used on violins, violas, cellos, lutes, older Flamenco guitars, ukuleles etc., are known as friction pegs. Friction pegs hold the string in tune by way of friction caused by their tapered shape and by the string pull created by the tight string. Some other commonly used slang names for guitar tuners are pegs, gears, machines, cranks, knobs, tensioners and tighteners.

Construction and action

Machine heads on a double bass

Traditionally, a single machine head consists of a cylinder or capstan, mounted at the center of a pinion gear, a knob or "button" and a worm gear that links them. The capstan has a hole through the far end from the gear, and the string is made to go through that hole, and is wrapped around the capstan. To complete the string installation, the string is tightened by turning the capstan using the tuning knob. The worm gear ensures that the capstan cannot turn without a movement on the knob; it also allows precise tuning.

Banjos usually employ a different mechanism using planetary gears - in this case the knob and the capstan both rotate on the same axis. A few guitars (e.g. the original Gibson Firebird, early Gibson basses and Mario Maccaferri's plastic instruments) have used this design.

The guitarist adjusts the tension of the various strings using the knobs so that they are correctly tuned: a higher tension yields a sharper pitch, a lower tension a flatter pitch. Typical tensions for steel-string acoustic guitars with "light" tension strings are 10.5 kgf (23.3 lbf, 103 N) to 13.8 kgf (30.2 lbf, 135 N).

Varieties

Normally, worm gears provide a gear ratio of 14:1. Versions with an 18:1 gear ratio also exist, trading better accuracy in fine tuning against slower initial string winding.

The machine heads on a classical guitar. Note the exposed gears and the decorations.
Martin EB18 bass guitar headstock, showing Martin open type machine heads.

Several kinds of machine head apparatus exist:

  • on classical guitars (with nylon strings), the worm gears are generally exposed; the strings are wound on the pins inside grooves in the head;
  • on steel-string guitars, including "folk" acoustic guitars and electric guitars, the worm gears are generally placed in individual sealed enclosures with permanent lubrication, although budget models may have exposed gears fixed on plates housing a row of gears. Vintage and vintage-reproduction guitars frequently have individual open-gear tuners, enclosed tuners not having become common until after WWII. Several machine head placements are possible, depending on the shape of the headstock:
    • rectangular head, 2 rows of 3 pins (or 6 pins for 12-string guitars): found on most "Folk" and "Jazz" guitars and on Gibson Les Paul guitars;
    • a single diagonal row of 6 pins: found on Fender Telecaster and Stratocaster guitars;
    • one diagonal row of four pins and one diagonal row of two pins: found on Music Man guitars;
  • on bass guitars, where string tension is extremely high, larger, heavier-duty machine heads than those used on guitars are used. Bass tuners generally feature larger knobs than guitar tuners as well; often these are distinctively shaped, and known as "elephant ears." Gear ratios of 20:1 are used often. Exposed gears are much more common in premium bass guitars than in six string non-bass instruments.
The reverse of the machine heads on a "folk" steel-string acoustic guitar. Note the enclosed gears.

Since the 1950s, guitar performance techniques evolved, and aggressive usage of a vibrato bar ("tremolo") became widespread. However, the original machine heads couldn't withstand the rigors of constant string tension changing, and strings could go out of tune after using a vibrato mechanism several times. Several manufacturers, including Grover and Floyd Rose, introduced a new design, commonly named locking machine heads nowadays: a machine head with additional mechanism to lock it in place and stabilize tuning while playing and using a vibrato bar. However, such machine heads reached limited success, mostly because of their price: as of 2006, locking ones are about 50% more expensive than original. Many break strings when tension is increased while the mechanism is locked and later unlocked, which frequently happens in music stores.

Note that on some guitars, such as those with Floyd Rose bridge, string tuning may be also conducted using microtuning tuners located at guitar bridge. In this case, main machine heads at headstock may be missing entirely, as well as the headstock itself.

Likewise, 'headless' guitars and basses, notably those designed by Steinberger and their licensed imitations, such as the Hohner Jack Bass, and unlicensed imitations such as the Washburn Bantam, have the machine heads at the body end. Steinbergers and Hohners require specialist double-ball end strings, whereas the Washburn Bantam can take regular strings.

Resistance to Usage

Certain instrumental families, most notably the Violin family (excepting the Double Bass) have been actively resistant to the use of machine heads, insisting on the continued use of friction pegs. The fitting of them on instruments in these families is often regarded as 'blasphemous' and will render an instrument un-resellable. The exact reasoning behind this resistance varies from case to case, with appearance, tradition, and simplicity, among others, being cited. This resistance remains despite the well-known issues with friction pegs losing tuning, coming loose, or jamming. In the early 2000s, a new type of machine head, utilizing micro-gearing inside of a friction-peg shaped casing that can be fitting to an instrument without physical alterations was introduced, and continues to be refined, but this technology is also facing resistance.

Notable designs

Several manufacturers established well-known designs of knobs and whole machine heads. These designs are subject to copy and reference:

References

Wikimedia Commons has media related to Machine heads.

There are several US patents on machine heads, mostly covering various aspects of locking:

  • US patent 5285709, John D. Grant, "Machine head for tuning a stringed instrument, especially a guitar or the like", issued 1994-02-15 
  • US patent D388817, Han Soo Kang, "Machine head for a guitar", issued 1998-01-06 
  • US patent D389508, Han Soo Kang, "Machine head for guitar", issued 1998-01-20 
  • US patent 6078001, Han Soo Kang, "Machine head for guitars", issued 2000-06-20 
  • US patent 6580022, Han Soo Kang, "Machine head for guitar", issued 2003-06-17 
Retrieved from "https://en.wikipedia.org/w/index.php?title=Machine_head&oldid=783831437"