PA-8000

The PA-8000 (PCX-U), code-named Onyx, is a microprocessor developed and fabricated by Hewlett-Packard (HP) that implemented the PA-RISC 2.0 instruction set architecture (ISA).^[1] It was a completely new design with no circuitry derived from previous PA-RISC microprocessors. The PA-8000 was introduced on 2 November 1995 when shipments began to members of the Precision RISC Organization (PRO).^[2] It was used exclusively by PRO members and was not sold on the merchant market. All follow-on PA-8x00 processors (PA-8200 to PA-8900, described further below) are based on the basic PA-8000 processor core.

The PA-8000 was used by:

HP in its HP 9000 workstations and servers
NEC in its TX7/P590 server
Stratus Computer in its Continuum fault-tolerant servers

Description

The PA-8000 is a four-way superscalar microprocessor that executes instructions out-of-order and speculatively.^[1]^[3] These features were not found in previous PA-RISC implementations, making the PA-8000 the first PA-RISC CPU to break the tradition of using simple microarchitectures and high-clock rate implementation to attain performance.^[4]

Instruction fetch unit

The PA-8000 has a four-stage front-end. During the first two stages, four instructions are fetched from the instruction cache by the instruction fetch unit (IFU).^[4] The IFU contains the program counter, branch history table (BHT), branch target address cache (BTAC) and a four-entry translation lookaside buffer (TLB).^[1]^[4] The TLB is used to translate virtual address to physical addresses for accessing the instruction cache. In the event of a TLB miss, the translation is requested from the main TLB.^[1]

Branch prediction

The PA-8000 performs branch prediction using static or dynamic methods.^[1] Which method the PA-8000 used was selected by a bit in each TLB entry. Static prediction considers most backwards branches as taken and forward branches as not taken. Static prediction also predicted the outcome of branches by examining hints encoded in the instructions themselves by the compiler.^[1]^[4]

Dynamic prediction uses the recorded history of a branch to decide whether it is taken or not taken. A 256-entry BHT is where this information is stored. Each BHT entry is a 3-bit shift register. The PA-8000 used a majority vote algorithm, a branch is taken if the majority of the three bits are set, and not taken if they are clear.^[1] A mispredicted branch causes a five-cycle penalty.^[4] The BHT is updated when the outcome of the branch is known. Although the PA-8000 can execute two branch instructions per cycle, only one of the outcomes is recorded as the BHT is not dual-ported to simplify its implementation.^[3]

The PA-8000 has a two-cycle bubble for correctly predicted branches, as the target address of the branch must be calculated before it is sent to the instruction cache.^[4] To reduce the occurrence of this bubble, the PA-8000 uses a 32-entry fully associative BTAC. The BTAC caches a branch's target address. When the same branch is encountered, and is predicted as taken, the address is sent to the instruction cache immediately, allowing the fetch to begin without delay.^[1]

To maximize the effectiveness of the BTAC, only the branch target of predicted-taken branches are cached. If a branch is predicted as not taken, but its target address is cached in the BTAC, its entry is deleted. In the event that the BTAC is full, and a new entry needs to be written, the entry that is replaced is selected using a round robin replacement policy.^[1]

Instruction cache

The instruction cache is external and supports a capacity of 256 KB to 4 MB. Instructions are pre-decoded before they enter the cache by adding five bits to each instruction. These bits reduce the amount of time required to decode the instruction later in the pipeline. The instruction cache is direct-mapped to avoid the complexity of set associative caches and is accessed via a 148-bit bus. The tags for the cache are also external. It is built from synchronous SRAMs (SSRAMs).

Decode, and the instruction reorder buffer

During the third stage, the instructions are decoded. In the fourth stage, they are placed in the instruction reorder buffer (IRB). The IRB's purpose is the implement register renaming, out of order execution, speculative execution and to provide a temporary place for results to be stored until the instructions are retired. The IRB determines which instructions are issued during stage five.

The IRB consists of two buffers, one for integer and floating-point instructions, the other for load and store instructions. Some instructions are placed into both buffers. These instructions are branch instructions and certain system instructions. Each buffer has 28 entries. Each buffer can accept up to four instructions per cycle and can issue up to two per a cycle to its functional units.

Execution

All instructions begin execution during stage six in the ten functional units. Integer instructions except for multiply are executed in two arithmetic logic units (ALUs) and two shift/merge units. All instructions executed in these units have a single-cycle latency and their results are written to the destination register in stage seven.

Floating-point instructions and integer multiply instructions are executed in two fused multiply–accumulate (FMAC) units and two divide/square-root units. The FMAC units are pipelined and have a three-cycle latency. Multiplication is performed during stage six, addition in stage seven, rounding in stage eight and writeback in stage nine. There is no rounding between the multiply and accumulate stages. The FMAC units also execute individual multiply and add instructions, which also have a latency of three cycles for both single-precision and double-precision variants. The divide/square-root units are not pipelined and have a 17-cycle latency. One instruction can be issued to them per clock cycle due to register port limitations, but they can operate in parallel with each other and the FMAC units.

Both integer and floating-point load and store instructions are executed by two dedicated address adders.

Translation lookaside buffer

The translation lookaside buffer (TLB) contains 96 entries and is dual-ported and full-associative. It can translate two virtual addresses per cycle. This TLB translates addresses for both instructions and data. When the IFU's TLB misses, this TLB provides the translation for it. Translation for loads and stores have a higher priority than those for instructions. Each TLB entry can be mapped to a page with a size between 4 KB to 16 MB, in increments that are powers of four.

Data cache

The PA-8000 has a data cache with a capacity up to 4 MB. The data cache is dual-ported, so two reads or writes can be performed during every cycle. It is dual-ported by implementing two banks of cache, thus it is not truly dual-ported because if two reads or writes reference the same bank, a conflict arises and only one operation can be performed. It is accessed by two 64-bit buses, one for each bank. The cache tags are external. There are two copies of the cache tags to allow independent accesses in each bank. The data cache is direct-mapped for the same reasons as the instruction cache. It is built from SSRAMs.

Runway bus

The external interface is the Runway bus, a 64-bit address and data multiplexed bus. The PA-8000 uses a 40-bit physical address, thus it is able to address 1 TB of physical memory.

Physical

The PA-8000 has 3.8 million transistors and measures 17.68 mm by 19.10 mm,^[5] for an area of 337.69 mm². It was fabricated by HP in their CMOS-14C process, a 10% gate shrink of the CMOS-14 process.^[4] The CMOS-14C process was a 0.5 µm, five-level aluminum interconnect, complementary metal–oxide–semiconductor (CMOS) process. The die has 704 solder bumps for signals and 1,200 for power or ground. It is packaged in a 1,085-pad flip chip alumina ceramic land grid array (LGA).^[6] The PA-8000 uses a 3.3 V power supply.

PA-8200

The PA-8200 (PCX-U+), code-named Vulcan, was a further development of the PA-8000. The first systems to use the PA-8200 became available in June 1997. The PA-8200 operated at 200 to 240 MHz and primarily competed with the Alpha 21164. Improvements were made to branch prediction and the TLB.^[3]^[7] Branch prediction was improved by quadrupling the number of BHT entries to 1,024, which required the use of a two-bit algorithm in order to fit without redesign of surrounding circuitry; and by implementing a write queue that enabled two branch outcomes to be recorded by the BHT instead of one. The number of TLB entries was increased to 120 entries from 96, which reduced TLB misses. The clock frequency was also improved through minor circuit redesign. The PA-8200's die was identical in size to the PA-8000 as improvements utilized empty areas of the die. It was fabricated in the CMOS-14C process.

PA-8500

The PA-8500 (PCX-W), code-named Barracuda, is a further development of the PA-8200. It taped-out in early 1998 and was introduced in late-1998 within systems. Production versions operated at frequencies of 300 to 440 MHz, but it was designed to, and has, operated up to 500 MHz.^[8] The most notable improvements are the higher operating frequencies and the on-die integration of the primary caches.^[9] The higher operating frequencies and the integration of the primary caches on the same die as the core was enabled by the migration to a 0.25 µm process. The PA-8200 core measured 10.8 mm by 11.4 mm (123.12 mm²) in the new process, less than half the area of the 0.5 µm PA-8200. This made area available that could be used for integrating the caches.

The PA-8500 has a 512 KB instruction cache and a 1 MB data cache. Other improvements to the microarchitecture include a larger BHT containing 2,048 entries, twice the capacity of the PA-8200's, and a larger TLB containing 160 entries. The PA-8500 uses a new version of the Runway bus. The new version operates at 125 MHz and transfers data on both rising and falling edges of the clock signal (double data rate, or DDR) and yields 240 MT/s or 2 GB/s of bandwidth. As the Runway bus is used to transfer addresses and data, usable bandwidth is 80% that of 2 GB/s, or around 1.6 GB/s.

The PA-8500 contains 140 million transistors and measures 21.3 mm by 22.0 mm (468.6 mm²).^[8] It was fabricated by Intel Corporation in a 0.25 µm CMOS process with five levels of aluminium interconnect. It uses a 2.0 V power supply. HP did not fabricate the PA-8500 themselves as they had ceased to upgrade their fabs to implement a process newer than CMOS-14C, which was used to fabricate previous PA-RISC microprocessors.

The PA-8500 was packaged in a smaller 544-pad land grid array (LGA) as the integration of the primary caches on die resulted in the removal of the two 128-bit buses which communicated with the external caches and their associated I/O pads.

PA-8600

The PA-8600 (PCX-W+), code-named Landshark, is a further development of the PA-8500 introduced in January 2000. The PA-8600 was intended to be introduced in mid-2000.^[10] It was a tweaked version of the PA-8500 to enable it to reach higher clock frequencies of 480 to 550 MHz. It improved the microarchitecture by using a quasi-least recently used (LRU) eviction policy for instruction cache. It was fabricated by Intel.

PA-8700

The PA-8700 (PCX-W2), code-named Piranha, is a further development of the PA-8600. Introduced in August 2001, it operated at 625 to 750 MHz. Improvements were the implementation of data prefetching, a quasi-LRU replacement policy for the data cache, and a larger 44-bit physical address space to address 16 TB of physical memory.^[11] The PA-8700 also has larger instruction and data caches, increased in capacity by 50% to 0.75 MB and 1.5 MB, respectively. The PA-8700 was fabricated by IBM Microelectronics^[12] in a 0.18 µm silicon on insulator (SOI) CMOS process with seven levels of copper interconnect and low-K dielectric.

PA-8700+

The PA-8700+ was a further development of the PA-8700 introduced in systems in mid-2002. It operated at 875 MHz.^[12]

PA-8800

The PA-8800, code-named Mako, is a further development of the PA-8700.^[13] It was introduced in 2004 and was used by HP in their C8000 workstation and HP 9000 Superdome servers. It was available at 0.8, 0.9 and 1.0 GHz. The PA-8800 was a dual-core design consisting of two modified PA-8700+ microprocessors on a single die. Each core has a 768 KB instruction cache and a 768 KB data cache. The primary caches are smaller than those in the PA-8700 to enable both cores to fit on the same die.

Improvements over the PA-8700 are improved branch prediction and the inclusion of an external 32 MB unified secondary cache. The secondary cache has a bandwidth of 10 GB/s and a latency of 40 cycles. It is 4-way set-associative, physically indexed and physically tagged with a line size of 128 bytes. The set-associativity was chosen to reduce the number of I/O pins. The L2 cache is implemented with using four 72 Mbit (9 MB) Enhanced Memory Systems Enhanced SRAM (ESRAM) chips, which despite its name, is an implementation of 1T-SRAM – dynamic random access memory (DRAM) with a SRAM-like interface. Access to this cache by each core is arbitrated by the on-die controller and the 1 MB of secondary cache tags also resides on-die as SRAM and is protected by ECC. The PA-8800 used the same front side bus as the McKinley Itanium microprocessor, which yields 6.4 GB/s of bandwidth, and is compatible with HP's Itanium chipsets such as the zx1.

It consisted of 300 million transistors, of which 25 million were for logic, on a 23.6 mm by 15.5 mm (365.8 mm²) die.^[13] It was fabricated by IBM in 0.13 µm SOI process with copper interconnects and low-k dielectric. The PA-8800 is packaged in a ceramic ball grid array mounted on a printed circuit board (PCB) with the four ESRAMs, forming a module similar to those used by early Itanium microprocessors.

PA-8900

The PA-8900, code-named Shortfin, was a derivative of the PA-8800. It was the last PA-RISC microprocessor to be developed and was introduced on 31 May 2005 when systems using the microprocessor became available.^[14] It was used in the HP 9000 servers and the C8000 workstation. It operated at 0.8, 0.9, 1.0 and 1.1 GHz. It is not a die shrink of the PA-8800, as was earlier rumored. The L2 cache was doubled in capacity to 64 MB, has lower latency, and better error detection and correction on caches. It uses the McKinley system bus and was compatible with Itanium 2 chipsets such as the HP zx1. There were no microarchitecture changes, but the floating-point unit and on-die cache circuitry was redesigned to reduce power consumption, and each core subsequently dissipated approximately 35 W at 1.0 GHz.

Notes

^ ^a ^b ^c ^d ^e ^f ^g ^h ⁱ Hunt 1995
^ "HP Announces Release of PA-8000 to PRO Partners".
^ ^a ^b ^c Scott 1997
^ ^a ^b ^c ^d ^e ^f ^g Gwennap 1994
^ Gaddis 1996, p. 1697
^ Kumar, "The HP PA-8000 RISC CPU"
^ Gwennap 1996
^ ^a ^b Barnes 1999
^ Gwennap 1997
^ Wermer, "HP's PA-8600 processor earlier to ship than expected".
^ Krewell 2000
^ ^a ^b ComputerWire 2002
^ ^a ^b Johnson 2001, p. 1
^ "HP delivers the last of the PA-RISC processors".

References

"HP delivers the last of the PA-RISC processors". (1 June 2005). Computer Business Review.
Barnes, Phillip (26 February 1999). "A 500 MHz 64 bit RISC CPU with 1.5Mbyte on chip Cache". Proceedings of the International Solid State Circuits Conference.
ComputerWire (28 June 2002). "HP readying dual-core PA-8800". The Register.
Gaddis, N.; Lotz, J. (November 1996). "A 64-b quad-issue CMOS RISC microprocessor". IEEE Journal of Solid-State Circuits 31 (11): pp. 1697–1702.
Gwennap, Linley (14 November 1994). "PA-8000 Combines Complexity and Speed". Microprocessor Report, Volume 8, Number 15.
Gwennap, Linley (28 October 1996). "HP Pumps Up PA-8x00 Family". Microprocessor Report, Volume 10, Number 14.
Gwennap, Linley (17 November 1997). "PA-8500's 1.5M Cache Aids Performance". Microprocessor Report.
Hewlett-Packard Company (2 November 1995). HP Announces Release of PA-8000 to PRO Partners. (Press Release)
Hill, J. Michael and Lachman, Jonathan (2000). "A 900MHz 2.25MByte Cache with On Chip CPU - Now in SOI/Cu". 2000 International Solid-State Circuits Conference.
Hunt, D. (1995). "Advanced performance features of the 64-bit PA-8000". Proceedings of CompCon. pp. 123–128.
Johnson, David J. C. (16 October 2001). "HP's Mako Processor". 2001 Microprocessor Forum.
Krewell, Kevin (22 May 2000). "HP Extends PA-RISC With 8700". Microprocessor Report.
Kumar, Ashok (19 August 1996). "The HP PA-8000 RISC CPU". Proceedings of Hot Chips VIII.
Lesartre, Greg; Hunt, Doug (1997). "PA-8500: The Continuing Evolution of the PA-8000 Family". Proceedings of CompCon.
Pountain, Dick (July 1995). "HP's Speedy RISC". Byte.
Scott, Anne P. et al. (August 1997). "Four-Way Superscalar PA-RISC Processors". Hewlett-Packard Journal.
Tsai, Li C. (16 February 2001). "A 1GHz PA-RISC Processor". International Solid State Circuits Conference.
Wermer, Sandra (8 March 1999). "HP's PA-8600 processor earlier to ship than expected". HOISe.