Tower Mounted Amplifier

Crowded mast with TMAs (white rectangular boxes) mounted behind all the panel (rectangular) antennas

A Tower Mounted Amplifier or Mast Head Amplifier is a Low-noise amplifier (LNA) mounted as close as practical to the antenna in mobile masts or base transceiver stations. A TMA reduces the base transceiver station noise figure (NF) and therefore improves its overall sensitivity; in other words the mobile mast is able to receive weaker signals.

Benefits in mobile communications

In two way communications systems, there are occasions when one way, one link, is weaker than the other, normally referenced as unbalanced links. This can be fixed by making the transmitter on that link stronger or the receiver more sensitive to weaker signals.

TMAs are used in mobile networks to improve the sensitivity of the uplink in mobile phone masts. Since the transmitter is a mobile phone it cannot be easily modified to transmit stronger signals. Improving the uplink translates into a combination of better coverage and mobile transmitting at less power, which in turn implies a lower drain from its batteries, thus a longer battery charge.

There are occasions when the cable between the antenna and the receiver is so lossy (too thin or too long) that the signal weakens from the antenna before reaching the receiver; therefore it may be decided to install TMAs from the start to make the system viable. In other words, the TMA can only partially correct, or palliate, the link imbalance.

Drawbacks/pitfalls

Simple phone mast with three TMAs (horizontal rectangular boxes) visible at the top of metal tower and before rectangular antennas

1. If the received signal is not weak, installing a TMA will not deliver its intended benefit.
2. If the received signal is strong enough, it may cause the TMA to create its own interference which is passed on to the receiver.
3. In some mobile networks (e.g. IS-95 or WCDMA - aka European 3G -), it is not simple to detect and correct unbalanced links since the link balance is not constant; link balance changes with traffic load. However, other mobile networks (e.g. GSM) have a constant link, therefore it is possible analyse call records and establish where TMAs are needed.
4. There might be practical room restrictions, visual, or structural weight restrictions to install a TMA at the top of a phone mast.
5. If the TMA fails, it may render the system unusable until serviced, unless it can be bypassed.
6. Servicing TMAs is harder than servicing receivers - and thus more expensive - as the TMA may be dangerously near (near field) of the antenna and high up in a tower. The receiver may alternatively be housed in a cabinet or hut at the base of the tower.

Mathematical principles

In a receiver, the receiving path starts with the signal originating at the antenna. Then the signal is amplified in further stages within the receiver. It is actually not amplified all at once but in stages, with some stages producing other changes (like changing the signal's frequency).

The principle can be demonstrated mathematically; the receiver's noise figure is calculated by modularly assessing each amplifier stage. Each stage consists of a noise figure (F) and an amount of amplification, or gain (G). So amplifier number 1 will be right after the antenna and described by $F_{1}$ and $G_{1}$. The relationship of the stages is known as the Friis formula.

$SystemNoiseFigure=F_{1}+{\frac {F_{2}-1}{G_{1}}}+{\frac {F_{3}-1}{G_{1}\times G_{2}}}+\cdots +{\frac {F_{n}-1}{G_{1}\times G_{2}\times G_{3}\times \cdots \times G_{n-1}}}$

Note that:

1. The first amplifier will set the temperature ($F_{1}$); nothing reduces its contribution to the total.
2. The second amplifier's temperature ($F_{2}$) will also influence the total but it is reduced (divided) by the gain of the first amplifier $G_{1}$.
3. The third amplifier's temperature is influencing even less, as it is reduced by its preceding amplifier gains $G_{1}$, $G_{2}$.
4. And so on until N stages.

Applying the Friis formula to TMAs

Typical receiver without TMA

Start with a typical receiver: Antenna - Connecting Cable (stage 1) - Receiver (stage 2).

$SystemNoiseFigure=F_{1}+{\frac {F_{2}-1}{G_{1}}}$

The first stage after the antenna is actually the connecting cable. Therefore:

• Stage 1: $F_{1}$ is equal to the loss of the cable and will increase with ambient temperature
• Stage 2: $G_{1}$ will depend on the lossiness of the cable. Since the element is lossy $G_{1}$ is less than one; in order words, it will increase $F_{2}-1$. The more loss, the closer $G_{1}$ is to zero and the more $F_{2}$ will increase.

What can be done to improve the receiver to pick up very weak signals? It must have a lower noise figure; that is when the TMA comes into use.

Typical receiver with TMA

It is a chain of 4 modules: antenna - short connecting cable (stage 1) - TMA (stage 2) - longer connecting cable (stage 3) - receiver (stage 4)

• Stage 1: By using the shortest, the least lossy connecting cable between the antenna and the TMA, $F_{1}$ is low$G_{1}$ is nearly one.
• Stage 2: The TMA of noise figure $F_{2}$ and gain $G_{2}$.
• Stage 3: Then comes the next cable ($F_{3}$ and $G_{3}$), but this time its noise addition ($F_{3}$) is reduced by $G_{2}$.
• Stage 4: Then comes the receiver, whose noise figure is less downgraded by the cables, as $G_{1}\approx 1$, $G_{2}$ is from the TMA, $G_{3}$ and from the second cable. So $G_{2}$ will counteract the effects of $G_{3}$.

Updating the Friis formula with this case, the noise figure is now:

$SystemNoiseFigure=F_{1}+{\frac {F_{2}-1}{1}}+{\frac {F_{3}-1}{1\times G_{2}}}+{\frac {F_{4}-1}{1\times G_{2}\times G_{3}}}$

In this way, the cable losses are now negligible and do not significantly affect the system noise figure.

This number is normally expressed in decibels (dB) thus:

$NoiseFigure(indB)=10\times \log _{10}(Fs)$

See also

• Low-noise block converter

External links

• TMA test equipment