User:Rosie1470/Ore shoots
![]() | This is the sandbox page where you will draft your initial Wikipedia contribution.
If you're starting a new article, you can develop it here until it's ready to go live. If you're working on improvements to an existing article, copy only one section at a time of the article to this sandbox to work on, and be sure to use an edit summary linking to the article you copied from. Do not copy over the entire article. You can find additional instructions here. Remember to save your work regularly using the "Publish page" button. (It just means 'save'; it will still be in the sandbox.) You can add bold formatting to your additions to differentiate them from existing content. |
Final Draft
[edit]Lead
[edit]An ore shoot is a hypogenic mass that is deposited in veins within a planar channel or lode, found in a shear or fault zone, fissure or lithologic boundary.[1] The ore shoot is the area of concentration which contains a primary ore along the veins present in the rock, and consists of the most valuable part of the deposit.
Article body
Gold Vein
[edit]In gold vein deposits the ore shoots tend to be deposited in an elongated plunging direction. The majority of the time the ore shoot plunge for orogenic gold deposits arises from the mineral deposition and direction of the fluid flow controlled by structures.[2]
![](http://upload.wikimedia.org/wikipedia/commons/thumb/d/db/Goldore.jpg/220px-Goldore.jpg)
Veins
[edit]Along an ore shoot, there is a rich gathering of different minerals within a vein. The veins can resemble a pipe, chimney or ribbon in structure and are are displaced mainly vertically oriented but also can be horizontal with large veins extending approximately 30 m (100 ft) horizontally and 150 m (500 ft) vertically. The metal contents in ore shoots are distributed in areas that vary in deposit sizes. When several lodes meet, they connect to form vein systems, these systems contain common fluid sources which causes general homogeneity within the mineralization types and ore shoot controls resulting in the veins sharing a common plumbing system.[1]
Sizes and structure
[edit]The circumference of deposit sizes can range from a few meters, to many kilometres. A structure may consist of multiple ore shoots with some veins or lodes being as thick as 1.5–6.1 m (5–20 ft), and extending to thousands of feet horizontally and vertically. The shoots tends to be thicker and richer in center areas rather than being distributed equally.[1]The geometrical values of the ore shoot are expressed using the breadth, dip and strike lengths as well as the plunge lengths. The average mass for most ore shoots are between 1 x 10^6 and 2 x 10^4 tonnes.[3]
Formation
[edit]There are complex stratigraphic historical parameters required in understanding how ore shoots are formed. Rocks go through numerous ductile and brittle deformation events before they become mineralized. The different locations of ore shoots in Australia are determined by investigating the internal architecture of the rock pile. The longest shoots occur on the flanks of the basalt flows with the largest lateral extent. The geometry and internal structure of the basalt flows is important for predicting the likelihood and extent of the ore shoots. The catalytic effect of different geological events leading up to an ore shoot formation is called "ground preparation".[1] Varying forms of ground preparation are; 1. sequential deformation which produces grain in the ore district. 2. sever faulting and jointing that enhances the permeability and surface area where the ore minerals can precipitate. 3. Interplay between the ore fluid deformation which produces an ore shoot.[1]
Location Example: Jianzhupo Deposit
[edit]Found in the Guangxi region in South China, the Jianzhupo Sb-Pb-Zn-Ag deposit has been explored and studied over decades, by using different parameters to understand the formation.[4] These include the use of geological fluid inclusions as well as H-O isotopic data that can be found during the mineralization's main stage. The Jianzhupo deposit is located within the Danchi Sn-polymetalic belt, and experienced major faulting and subsidence during the Devonian-Carboniferous Periods following folding during the Middle Triassic, and then finally underwent extension during the Cretaceous.[4] The deposit was drilled into for fluid inclusions samples at varying depths, recovering 30 thin sections that were then used for petrographic fluid inclusion analysis.
- ^ a b c d e Peters, Stephen G. (1993-04-01). "Nomenclature, concepts and classification of oreshoots in vein deposits". Ore Geology Reviews. Structural Setting and Controls on Mineral Deposits. 8 (1): 3–22. doi:10.1016/0169-1368(93)90025-T. ISSN 0169-1368.
- ^ Wang, Si-Rui; Yang, Li-Qiang; Wang, Jian-Gang; Wang, En-Jing; Xu, Yong-Lin (2019-04). "Geostatistical Determination of Ore Shoot Plunge and Structural Control of the Sizhuang World-Class Epizonal Orogenic Gold Deposit, Jiaodong Peninsula, China". Minerals. 9 (4): 214. doi:10.3390/min9040214. ISSN 2075-163X.
{{cite journal}}
: Check date values in:|date=
(help)CS1 maint: unflagged free DOI (link) - ^ Peters, Stephen G. (1993-04-01). "Nomenclature, concepts and classification of oreshoots in vein deposits". Ore Geology Reviews. Structural Setting and Controls on Mineral Deposits. 8 (1): 3–22. doi:10.1016/0169-1368(93)90025-T. ISSN 0169-1368.
- ^ a b "Genesis of the Jianzhupo Sb–Pb–Zn–Ag deposit and formation of an ore shoot in the Wuxu ore field, Guangxi, South China". Ore Geology Reviews. 102: 654–665. 2018-11-01. doi:10.1016/j.oregeorev.2018.09.026. ISSN 0169-1368.