Duramax V8 engine

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by 36.84.223.138 (talk) at 14:12, 24 June 2016. The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Duramax Diesel engine
Overview
ManufacturerDMAX
Production2001–
Chronology
Predecessor6.2 and 6.5 L Detroit Diesel

The Duramax is a General Motors diesel engine family for light to medium duty trucks, designed by GM and Isuzu. The 6.6-liter Duramax is produced by DMAX, a joint venture between GM and Isuzu in Moraine, Ohio. The Duramax block and heads are poured at The Defiance GM Powertrain foundry in Defiance, Ohio. This engine was initially installed in 2001 model year Chevy and GMC trucks and has been an option since then in pickups, vans, and medium-duty trucks. In 2006, production at Moraine was reportedly limited to approximately 200,000 engines per year.[1] On May 9, 2007, DMAX announced the production of the 1,000,000th Duramax V-8 diesel at its Moraine facility.[1]

Duramax LML

Engine RPO Codes

LB7

RPO LB7 (engine code "1") was first introduced in 2001 and continued until mid-2004. It is a 32-valve design with high-pressure common-rail direct injection and an experimental composite design cylinder head. The most common issue with the LB7 is injector failure, so common that a special policy bulletin was issued (#04039B). Fuel leaked and entered the crankcase, causing oil dilution. Early on, customers came forward complaining of severe overheating, and in some situations, blown head gaskets. Initially GM denied it was a problem, but after being sued by a consumer group, GM relented and included overheating and blown head gaskets as a warranted item. GM issued a warranty for this after the fact for injectors, which now have 7 year/200,000 mile coverage.[citation needed] The following trucks use the LB7:

Specifications

  • Engine type: 6,599 cc (402.7 cu in) V8 turbo
  • Bore x Stroke: 4.06 in (103 mm) x 3.90 in (99 mm)
  • Block / Head: Iron / aluminum
  • Aspiration: Turbocharged & Intercooled
  • Valvetrain: OHV 4-V
  • Compression: 17.5:1
  • Injection: Direct; Robert Bosch GmbH high pressure common-rail
  • Power / Torque: 300 bhp (220 kW) @ 3100 rpm / 520 lb⋅ft (705 N⋅m) @1800 rpm
  • Source:[2]

LLY

The LLY (internally called the 8GF1) (engine code "2") is a 6,599 cc (402.7 cu in) turbocharged engine which debuted in mid-2004 and continued until the end of 2005. It is a 32-valve design with high-pressure common-rail direct injection and aluminum cylinder heads. The LLY was GM's first attempt to implement emissions requirements on their diesel trucks. To meet this goal they turned to a newly developed Garrett turbocharger with a variable geometry vane system and they installed an Exhaust Gas Recirculation valve or (EGR Valve). Learning from problems with injectors in the previous LB7 GM changed the valve covers to allow access to the injectors without having to remove the valve covers, saving significant labor costs if injector replacement became necessary.

The following trucks used the LLY engine:

Specifications

  • Engine type: 6,599 cc (402.7 cu in) V8 turbo
  • Bore x Stroke: 4.06 in (103 mm) x 3.90 in (99 mm)
  • Block / Head: Cast gray iron / Cast aluminum
  • Aspiration: Turbocharged & Intercooled
  • Valvetrain: OHV 4-v
  • Compression: 17.5:1
  • Injection: Bosch High Pressure Common-rail
  • Power / Torque: 305 bhp (227 kW) @3000 rpm / 605 lb⋅ft (820 N⋅m) @1600 rpm
  • Head casting is 8gf1
  • Block casting is #22351021213
  • Source:[3]

LLY/LBZ

The LBZ (engine code "D") debuted in late 2006 and continued into 2007 sold only in the "classic" body style. It has an improved engine computer tune that produces increased power and torque over the 2005.5 LLY version of the motor. First appearance of the Duramax in the Express/Savanna vans.

Changes include:

  • Cylinder block casting and machining changes strengthen the bottom of the cylinder bores to support increased power and torque
  • Upgraded main bearing material increases durability
  • Revised piston design lowers compression ratio to 16.8:1 from 17.5:1
  • Piston pin bore diameter increased for increased strength
  • Connecting rod “ I ” section is thicker for increased strength
  • Cylinder heads revised to accommodate lower compression and reduced cylinder firing pressure
  • Maximum injection pressure increased from 23,000 psi (1,585.8 bar) to more than 26,000 psi (1,792.6 bar)
  • Fuel delivered via higher-pressure pump, fuel rails, distribution lines and all-new, seven-hole fuel injectors
  • Fuel injectors spray directly onto glow plugs, providing faster, better-quality starts and more complete cold-start combustion for reduced emissions
  • Improved glow plugs heat up faster through an independent controller
  • Revised variable-geometry turbocharger is aerodynamically more efficient to help deliver smooth and immediate response and lower emissions
  • Air induction system re-tuned to enhance quietness
  • EGR has larger cooler to bring more exhaust into the system
  • First application of new, 32-bit E35 controller, which adjusts and compensates for the fuel flow to bolster efficiency and reduce emissions"

LBZ applications:

LLY applications:

Specifications

  • Engine type: 6,599 cc (402.7 cu in) V8 turbo
  • Bore x Stroke: 4.06 in (103 mm) x 3.90 in (99 mm)
  • Block / Head: Cast gray iron / Cast aluminum
  • Aspiration: Turbocharged & Intercooled
  • Valvetrain: OHV 4-V
  • Compression: 16.8:1
  • Injection: Bosch High Pressure Common-rail
  • Power / Torque:
Code Years Power@rpm Torque@rpm Redline (rpm)
LBZ (Chevrolet Silverado 2500HD / 3500 Classic (auto trans), GMC Sierra 2500HD / 3500 Classic (auto trans)) 2006–2007 360 bhp (270 kW) @3200 650 lb⋅ft (881 N⋅m) @1600 3450
LLY (Chevrolet Kodiak Medium Duty (LRX option), GMC TopKick Medium Duty (LRX option), Hummer H1 Alpha) 2004–2005 300 bhp (220 kW) @3000 520 lb⋅ft (705 N⋅m) @1600 3200
LBZ(Chevrolet Kodiak Medium Duty (LPD option), GMC TopKick Medium Duty (LPD)) 2006–2007 300 bhp (220 kW) @3000 605 lb⋅ft (820 N⋅m) @1600 3200
LLY (Chevrolet Express, GMC Savana) 2006–2007 250 bhp (190 kW) @3200 460 lb⋅ft (624 N⋅m) @1600 3450

LMM

The LMM (engine code "6") debuted part way through 2007 and ended production with the start of the 2011 calendar year and is mated to the 6-speed Allison transmission. The LMM was the only Duramax offered for model years 2008-2010.[4]

A version was used in Trident Iceni .[5]

Specifications

  • Engine type: 6,599 cc (402.7 cu in) V8 turbo
  • Bore x Stroke: 4.06 in (103 mm) x 3.90 in (99 mm)
  • Block / Head: Cast gray iron / Cast aluminum
  • Aspiration: Turbocharged & Intercooled
  • Valvetrain: OHV 4-V
  • Compression: 16.8:1
  • Injection: Bosch High Pressure Common Rail with CP3.3 Injection Pump
  • Power / Torque: 365 bhp (272 kW) @3200 rpm / 660 lb⋅ft (895 N⋅m) @1600 rpm
Code Years Power@rpm Torque@rpm Redline (rpm)
LML (Chevrolet Silverado HD, GMC Sierra HD) 2011–present 397 bhp (296 kW) @3000 765 lb⋅ft (1,037 N⋅m) @1600 3450
LMM (Chevrolet Silverado HD, GMC Sierra HD) 2007–2010 365 bhp (272 kW) @3200 660 lb⋅ft (895 N⋅m) @1600 3450
LMM (Chevrolet Kodiak Medium Duty (LYE option), GMC TopKick Medium Duty (LYE option)) 2007–2010 330 bhp (250 kW) @3000 620 lb⋅ft (841 N⋅m) @1600 3250
LMM (Chevrolet Kodiak Medium Duty (LRX option), GMC TopKick Medium Duty (LRX option)) 2007–2010 300 bhp (220 kW) @3000 520 lb⋅ft (705 N⋅m) @1600 3250
LMM (Chevrolet Express, GMC Savana) 2007–2010 250 bhp (190 kW) @3200 460 lb⋅ft (624 N⋅m) @1600 3450
LMM (Chevrolet Express, GMC Savana) 2011-2014 260 bhp (190 kW) @3100 525 lb⋅ft (712 N⋅m) @1600 3450

Emission controls:

  • Additional combustion control, including an even more efficient variable-geometry turbocharging system, cooled (enhanced) exhaust gas recirculation (EGR) and closed crankcase ventilation to reduce nitrogen oxides (NOx)
  • Additional exhaust control, including oxidizing catalyst and new diesel particulate filter (DPF) to reduce soot and particulate matter
  • Increased-capacity cooling system
  • New engine control software
  • Use of low-ash engine oil (CJ-4)

Applications:

LML

The 6.6L RPO LML (VIN code "8") is the latest version (2011–present) of the Isuzu/GM Duramax V8 diesel engine and actually a further advanced version of the LMM engine with the majority of the changes addressing a required drastic reduction in engine emissions. Some mechanical aspects of the engine, such as piston oil flow design for improved temperature control and oil pump design, were also improved to enhance durability even further.

The LML engine was significantly updated for 2011 to provide improved exhaust emissions that comply with the new federal emission standards for diesel engines, provide better engine rigidity and further noise reduction. New 29,000 PSI piezo injectors, a complete fuel system-hardening to tolerate up to 20% biodiesel mixtures and urea injection (to reduce Nitrogen oxides) with a 5.3 gallon urea tank are updating the fuel and emissions systems. This engine has a fuel injector in the exhaust tract, to allow raw fuel injection during the particulate filter recycling routine. The RPO LML engine is rated at 397 horsepower (296 kW) at 3000 rpm and 765 lb⋅ft (1,037 N⋅m) of torque at 1600 rpm.[9]

LGH

The 6.6L Duramax diesel engine (VIN code "L") is used on 2010 interim and 2011 Chevrolet Express and GMC Savana vans and 2011 Chevrolet Silverado and GMC Sierra trucks with RPO ZW9 (chassis cabs or trucks with pickup box delete). The LGH engine is rated at 335 bhp (250 kW) at 3100 rpm and 685 lb⋅ft (929 N⋅m) at 1600 rpm. Similar to the LML this engine also uses a DPF and DEF system to meet emission standards.

LMK

This engine is not yet commercially launched although it was touted in the automobile press as one of the most important new engine concepts for small trucks and SUVs by finally delivering a capable diesel engine in a compact enough package. The engine project is currently on indefinite hold by GM. General Motors planned a 4.5-litre 72-degree[10] V8 for light-duty applications which would be built at GM's powertrain facility in Tonawanda, New York after 2009. Designed to fit in the same space as a Chevrolet Small-Block engine, it is expected to produce over 310 bhp (230 kW) and 520 lb⋅ft (705 N⋅m) of torque. It added urea injection, 29,000-psi (2,000 bar) piezo-electric common-rail fuel system over previous Duramax architecture.[11]

It was initially targeted for the Chevy Silverado/GMC Sierra and Hummer H2.[12] Unlike previous Duramax engines, the 4.5-liter is planned to be designed and built entirely by GM, without assistance from Isuzu.[13]

As of March 2009, a GM spokesperson stated the engine project has been put on an "indefinite hold" due to current economic conditions.[14]

See also

References

  1. ^ a b "GM celebrates one-millionth Duramax diesel". Retrieved May 9, 2007.
  2. ^ 2003 spec sheet
  3. ^ a b 2007 LLY LBZ spec sheet
  4. ^ "Duramax VIN Engine Identification". DuramaxDieselSpecs.com. Retrieved 2012-03-14.
  5. ^ Jeremy Korzeniewski RSS feed. "Trident diesel sports car not vaporware, still sounds too good to be true". Autoblog.com. Retrieved 2011-12-02.
  6. ^ "2007 LMM specs". Archives.media.gm.com. 2005-03-31. Retrieved 2011-12-02.
  7. ^ 2009 GMC Sierra HD engine curve
  8. ^ 2007 CHEVROLET SILVERADO AND GMC SIERRA HEAVY-DUTY PICKUPS DELIVER THE CAPABILITY FOR ANY TASK
  9. ^ General Motors (10 March 2010). "GMC's 2011 Heavy-Duty Trucks Build On Proven Strong Heritage With New Duramax 6.6L Turbo Diesel Engines".
  10. ^ "2010 Duramax 4500 Diesel".
  11. ^ John Neff RSS feed. "GM releases details on upcoming 4.5L Duramax turbo-diesel V8". Autoblog.com. Retrieved 2011-12-02.
  12. ^ Neff, John (2007-06-15). "GM announces new 4.5L V8 Duramax diesel for half-ton trucks and HUMMER poopH2". Autoblog. Retrieved 2007-06-21.
  13. ^ Levine, Mike (2007-06-15). "GM Announces Production of New 4.5-Liter Duramax Diesel V8 for Light Duty Pickups". PickupTruck.com. Retrieved 2007-06-21.
  14. ^ Colin Mathews (11 March 2009). "Chevy Puts Baby Duramax On Hold Until Further Notice".

External links