Toyota VZ engine
 |
| Toyota VZ engine | |
|---|---|
 | |
| Overview | |
| Manufacturer | Toyota Motor Corporation |
| Production | 1988–2004 |
| Layout | |
| Configuration | DOHC 60° 24-valve V6 |
| Chronology | |
| Predecessor | Toyota G engine |
| Successor | Toyota MZ engine Toyota GR engine |
The Toyota VZ engine family is a series of V6 gasoline piston engines ranging from 2.0L to 3.4L in displacement and both SOHC and DOHC configurations. The family introduced many changes for Toyota, including various EFI, ECU, and engine improvements from generation to generation. The VZ was Toyota's response to the Nissan VG engine. The low angle DOHC cylinder heads excel in low-mid torque and power, making the VZ well-suited for various uses in cars, trucks, and SUVs.
The blocks are all strongly made using cast iron with large interconnected main bearing cradles and two bolt main bearing caps. Forged steel crankshafts, and cast iron main bearing support girdles became standard with the 3VZ-FE. Piston and ring construction are typical parts, with rods varying between large and very large for stock V6 production engines.
1VZ-FE
The 1VZ-FE is a 2.0 L (1992 cc) version. Bore is 78 mm (3.07 in) and stroke is 69.5 mm (2.74 in). Output is 136 hp (101 kW) at 6000 rpm and 128 lb·ft (173 N·m) at 4600 rpm.
Applications: Japan
- 1988–1991 Toyota Camry Prominent VZV20 and VZV3x
- 1988–1991 Toyota Vista
2VZ-FE
The 2VZ-FE is a 2.5 L (2507 cc) version. Bore is 87.5 mm (3.4 in) and stroke is 69.5 mm (2.7 in) and the compression ratio is 9.0. Output is 119 kW (159 bhp) at 5800 rpm and 216 N⋅m (159 lb⋅ft) at 4600 rpm with red line limit of 6800 rpm.
Applications:
- 1988–1991 Toyota Camry
- 1989–1991 Lexus ES 250
3VZ-E
The 3VZ-E is a 3.0 L (2958 cc) version and is the only SOHC VZ-series engine, and the only non-DOHC V6 Toyota has ever built. Bore remains at 87.5 mm (3.44 in) but stroke is pushed to 82.0 mm (3.23 in). At introduction output was specified as 145 hp (108 kW) then later bumped to 150 hp (112 kW) at 4800 rpm with 180 lb·ft (244 N·m) of torque at 3400 rpm. Despite sharing an engine family designation the 3VZ-E and 3VZ-FE have few parts in common.
Applications:
- 1988–1995 Toyota 4Runner
- 1988–1995 Toyota Pickup
- 1992–1995 Toyota T100
3VZ-FE
|
The basic design is a revised 3VZ-E iron-block engine, mated with aluminum DOHC 24 valve heads. It has a forged steel crankshaft and cast connecting rods. The upper intake plenum is of the split-chamber design with Toyota's ACIS variable-intake system feeding three sets of runners for both heads.
Because the VZ was originally for pickup truck and SUV use, the 3VZ-FE happens to be a physically tall motor. To make the engine fit in FWD engine bays, Toyota tilted the motor towards the firewall. This "tilt" is so severe (~15 degrees) that reaching the rear bank of cylinders is nearly impossible without first removing the intake plenum.
Parts-wise, the 3VZ-FE shares very little with the rest of the VZ engine family. The main bearings are shared with the 3VZ-E, but little else. Cams can also be interchanged between the 5VZ-FE and 3VZ-FE heads.
The 3VZ-FE was used on the Camry platform from 1992 to May 1997 depending on the market: North America saw the engine only in 1992 and 1993, while Australia and New Zealand had it from 1992 to 1996. The engine was available in some parts of Asia in the Toyota Windom until May 1997. Following 1994, the 1MZ-FE engines replaced the 3VZ-FE in most applications. However the 3VZ-FE continued to be used in Australia until 1996, especially in the Camry. The power spread of the 3VZ-FE is wide, having close to maximum torque between 2500–4600 rpm, with power trailing off by 6000 rpm. The stock redline is 6600 rpm, and the ECU's fuel/ignition cut-off is 7200 rpm.
The 1992–1993 engine is rated at 185 hp (138 kW) at 5800 rpm and 189 lb⋅ft (256 N⋅m) at 4600 rpm. Compression ratio is 9.6:1. The 3VZ-FE is fairly common in most parts of the world, having a long lifespan in popular models.
Applications:
- 1993–1996 Toyota Scepter, Japan
- 1992–1993 Toyota Camry, USA
- 1992–1996 Toyota Camry, Australia, Europe
- 1992–1996 Toyota Windom
- 1992–1993 Lexus ES300, USA
4VZ-FE
The 4VZ-FE is a 2.5 L (2496 cc) version. Bore is 87.5 mm (3.44 in) and stroke is ever so slightly lower from the 2VZ-FE at 69.2 mm (2.72 in). Output is 173 hp (129 kW) at 6000 rpm. Compression ratio of this engine was raised from 9.0:1 to 9.6:1. In production from 1992 until 1996, it was built to replace the 2VZ-FE as Toyota's 2.5 L V6. Engine was only sold with Japanese market vehicles.
Applications: Japan
- 1992–1996 Toyota Camry Prominent
- 1993–1996 Toyota Windom VCV11
5VZ-FE
The 5VZ-FE is a 3.4 L (3378 cc) engine which replaced the 3VZ-E. Bore is up to 93.5 mm (3.68 in) and stroke is 82.0 mm (3.23 in) while the compression ratio stays the same as the 3VZ-FE at 9.6:1. Output is 190 hp (142 kW) at 4800 rpm with 220 lb·ft (298 Nm) of torque at 3600 rpm. It has a cast iron engine block, and aluminum DOHC cylinder heads. The 5VZ-FE uses sequential multi-port fuel injection, has four valves per cylinder with shim-over-bucket tappets and features large cast connecting rods, one-piece cast camshafts, a cast crank (unlike the 3VZ-FE, which was forged) and a cast aluminum intake manifold. This engine also features an oil cooler and a wasted spark ignition system with three coils.
Camshafts are belt-driven. The 5VZ-FE is a non-interference engine.
Applications:
- 1995–2004 Toyota Tacoma
- 2000–2004 Toyota Tundra
- 1995–1998 Toyota T-100
- 1996–2002 Toyota 4Runner
- 1993–2004 Toyota Land Cruiser Prado
- Toyota Granvia
- 2000-2002, 2004 GAZ-3111
See also
