Clerget aircraft engines
Clerget was the name given to a series of early rotary aircraft engine types of the World War I era that were designed by Pierre Clerget. Manufactured in both France by Clerget-Blin and Great Britain by Gwynnes Limited they were used on such aircraft as the Sopwith Camel and Vickers Gunbus.
Rotary engine development
What distinguished the Clerget rotary engine from its rivals (Gnome and Le Rhône) was that the Clerget had normal intake and exhaust valves unlike the Gnome, and the connecting rod arrangement was much simpler than the Le Rhone. A source of failure among the Clerget engines were the special-purpose piston rings, called obturator rings. These were located below the gudgeon or wrist pin, to block heat transfer from the combustion area to the lower part of the cylinder and overcome their subsequent distortion. These rings were often made from brass and only had a lifespan of a few hours. The Clerget engines were considered reliable but they cost more per unit to produce than their rivals. Unlike other contemporary rotaries in which the ignition system was either switched on or off to provide a rudimentary form of engine speed control, the Clerget featured a throttle.
The Clerget rotary engines were air-cooled with either seven, nine or eleven cylinders. They were fitted with a double thrust ball race, which enabled them to be used either as a pusher or as a tractor engine.
The engines worked on a four-stroke cycle. The chief points of difference from other rotary engines were:
- The pistons were of an aluminium alloy.
- The connecting rods had a tubular section.
- The inlet and exhaust valves were mechanically operated by means of separate cams, tappets and rocker arms.
The direction of rotation was counter (anti)-clockwise as seen from the propeller-end of the engine. Between any two consecutive firing strokes, the engine turned through 80 degrees. Like many other rotary engines of the period they were made chiefly of steel, for strength and lightness.
Rotary engine types
- Clerget 7Z
- (1911) 80 hp (60 kW), seven-cylinder.
- Clerget 9B
- (1913) 130 hp (97 kW), nine-cylinder.
- Clerget 9Bf
- (1915) 140 hp (104 kW), nine-cylinder long stroke version of the Clerget 9B. The most numerous British production engine with 2,350 units being built.
- Clerget 9J
- Clerget 9Z
- (1917) 110 hp (82 kW), nine-cylinder. Redesigned with aluminium pistons, tubular connecting rods and revised valve gear.
- Clerget 11Eb
- (1918) 200 hp (150 kW), 11-cylinder, single-row engine.
Rotary engines on display
- A locally-built Clerget 9B of 1917 is displayed at the Museum of Lincolnshire Life.
- A preserved Clerget 9B engine is on public display at the Fleet Air Arm Museum, RNAS Yeovilton.
Radial 'X' engines
- Clerget 16X
- A 420 hp (310 kW) 16-cylinder, four-row X engine.
Diesel radial engines
- Clerget 9A
(1929) 100 hp (75 kW) Nine-cylinder, single row radial engine.
- Clerget 9B
- Clerget 9C
- Produced under licence by Hispano-Suiza as the Hispano-Suiza 9T
- Clerget 14F-01
(1937) 14-cylinder, two-row radial engine, flown in a Potez 25 biplane.
- Clerget 14F-02
- Clerget 14Fcs
- "Air Board" Technical Notes issued by Controller Technical Department for persons holding an official position in His Majesty's Service dated 1918
- Gunston, Bill (1986). World Encyclopedia of Aero Engines. Wellingborough: Patrick Stephens. pp. 44–45.
- Clerget Aero Engines: Instructions and List of Parts. Camden Miniature Steam Services. 2001 . ISBN 0-9536523-1-9.
|Wikimedia Commons has media related to Clerget rotary engines.|