Jump to content

Ice hockey stick: Difference between revisions

From Wikipedia, the free encyclopedia
Content deleted Content added
No edit summary
Line 3: Line 3:
{{otheruses2|Hockey stick}}
{{otheruses2|Hockey stick}}


An '''ice hockey stick''' is a piece of equipment used in [[ice hockey]] to move the puck. Ice hockey sticks are approximately 150-200 cm long, composed of a long, slender shaft and a flat extension at one end called the blade. The blade is the part of the stick used to contact the puck, and is typically 25 to 40 cm long. Stick dimensions can vary widely, as they are usually built to suit a particular player's size. The blade is positioned at roughly a 135° angle from the axis of the shaft, giving the stick a partly 'L-shaped' appearance. The shaft of the stick is fairly rigid, but it has some flexibility to benefit some [[Shot (hockey)|shots]].
An '''ice hockey stick''' is a piece of equipment used in [[ice hockey]] to shoot, pass, and carry the puck. Ice hockey sticks are approximately 150-200 cm long, composed of a long, slender shaft with a flat extension at one end called the blade. The blade is the part of the stick used to contact the puck, and is typically 25 to 40 cm long. Stick dimensions can vary widely, as they are usually built to suit a particular player's size and preference. The blade is positioned at roughly a 135° angle from the axis of the shaft, giving the stick a partly 'L-shaped' appearance. The shaft of the stick is fairly rigid, but it has some flexibility to benefit some [[Shot (hockey)|shots]].


The blade is often curved in the direction toward which the skater moves forward, to aid in retaining or lifting the puck off the playing surface.
The blade is often curved in the direction toward which the skater moves forward, to aid in retaining or lifting the puck off the playing surface.
<!-- This section is poorly written, and is a verbatim copy from http://www.dunedinicehockey.co.nz/tips/equipment.php

Having the stick curved gives a player superior puck control over no curve in the blade. The blade on a hockey stick can have a forward or backward twist depending on the players preference. A blade with a forward twist (where the toe, or front of the stick angles back) can allow the player to achieve greater height and accuracy in wrist shots, but deprives them from a strong backhand or slapshot. A twist where the toe of the blade curves down, allows more accurate slap and backhand shots, but makes it harder for the player to achieve height in the wristshot. The player depending on preference will find a balance of the two.
-->


The goaltender has a slightly modified stick. The lower part of the stick is wider, the angle is smaller, and the blade is slightly curved towards the direction of the play.
The goaltender has a slightly modified stick. The lower part of the stick is wider, the angle is smaller, and the blade is slightly curved towards the direction of the play.
Line 39: Line 35:
Wooden sticks are usually constructed by laminating multiple types of wood into a high quality [[plywood]], then coating the stick and blade with thin plastic or fiberglass. Some manufacturers use fiberglass as a laminate between wood layers. Today in the [[NHL]], only 16 players still use wooden sticks, including [[Ottawa Senators]] [[Jason Spezza]] and [[Vancouver Canucks]] [[Markus Naslund]].
Wooden sticks are usually constructed by laminating multiple types of wood into a high quality [[plywood]], then coating the stick and blade with thin plastic or fiberglass. Some manufacturers use fiberglass as a laminate between wood layers. Today in the [[NHL]], only 16 players still use wooden sticks, including [[Ottawa Senators]] [[Jason Spezza]] and [[Vancouver Canucks]] [[Markus Naslund]].


The main advantage that wooden sticks enjoy today is their relatively low cost. Few wooden sticks cost more than $40 per copy, compared to $200+ for some composite varieties. This makes them a popular choice by younger and amateur players. Wooden sticks also enjoy a repuation of having a good "feel" compared to aluminum or titanium choices. The main disadvantage that wooden sticks suffer from is the relative irregularity and poor durability of the wooden construction. Wood has a tendency to warp, and gradually over time will lose its stiffness properties as a player uses it. Wood, being a natural material, also creates variations in production (even between identical patterns), and it cannot be made as "responsive" as certain composite materials (which decreases velocity and accuracy on wrist and snap shots).
The main advantage that wooden sticks enjoy today is their relatively low cost. Few wooden sticks cost more than $40 per copy, compared to $200+ for some composite varieties. This makes them a popular choice by younger and amateur players. Wooden sticks also enjoy a repuation of having a good "feel" compared to aluminum or titanium choices. The main disadvantage that wooden sticks suffer from is the relative irregularity and poor durability of the wooden construction. Wood has a tendency to warp, and over time its flex and stiffness properties will change. Additionally, being a natural material, wood also creates variations in production (even between identical patterns), and it cannot be made as "responsive" as certain composite materials (which decreases velocity and accuracy on wrist and snap shots).


It is a common misperception that, for most players, aluminum or composite sticks make for harder slap shots. For slap shots specifically, wooden sticks have very similar properties to composite sticks, and for most players there will be very little difference in velocity between wood and other materials. It should also be noted that the short list of players with the hardest slap shots in NHL history ([[Bobby Hull]], [[Al MacInnis]], [[Al Iafrate]], among others) all used wooden sticks (although of course they did not have access to the composite variety).
It is a common misperception that, for most players, aluminum or composite sticks make for harder slap shots. As it relates to slap shots specifically, wooden sticks have very similar properties to composite sticks, and for most players there will be very little difference in velocity between wood and other materials. It should also be noted that the short list of players with the hardest slap shots in NHL history ([[Bobby Hull]], [[Al MacInnis]], [[Al Iafrate]], among others) all used wooden sticks (although of course they did not have access to the composite variety).


====Aluminum====
====Aluminum====
Line 67: Line 63:


Titanium is similar to aluminum in general properties, although it is lighter, stronger, and is said to have notably superior "flex" properties (due mainly to the relative thinness of the walls of the shaft).
Titanium is similar to aluminum in general properties, although it is lighter, stronger, and is said to have notably superior "flex" properties (due mainly to the relative thinness of the walls of the shaft).

==Stick Properties==


===Lie===
===Lie===
Line 84: Line 82:
Hockey stick shafts, much like [[golf club]] shafts, are highly flexible, and this flexibility is a key component in their performance. ''Flex'', ''bend'', ''stiffness'', and ''whip'' are all terms used to describe the amount force required to bend a given stick shaft a certain amount.
Hockey stick shafts, much like [[golf club]] shafts, are highly flexible, and this flexibility is a key component in their performance. ''Flex'', ''bend'', ''stiffness'', and ''whip'' are all terms used to describe the amount force required to bend a given stick shaft a certain amount.


With most composite and alumimum sticks, their flex characteristic is correlated numerically. This number, which ranges from 50 through 120, is printed on the stick and corresponds to the amount force (in [[pounds-force]]) that it takes to deflect or bend the shaft one inch. For example, a 100 flex requires 100 pounds force (444 [[Newtons|N]]) to bend the shaft 1 inch. A 90 flex requires 90 pounds force (400 N) to bend the shaft 1 inch, and so on. Witch means that the lower the flex number the more you can bend it
With most composite and alumimum sticks, their flex characteristic is correlated numerically. This number, which ranges from 50 through 120, is printed on the stick and corresponds to the amount force (in [[pounds-force]]) that it takes to deflect or bend the shaft one inch. For example, a 100 flex requires 100 pounds force (444 [[Newtons|N]]) to bend the shaft 1 inch.


Stick flex is viewed as a very important characteristic by most players. Commonly, [[defenceman (ice hockey)|defencemen]] seek stiffer flex shafts, as their greater stiffness imparts more force on slap shots and improves [[checking (ice hockey)|stick-checking]]. Forwards will commonly seek more flexible shafts, as they require less force to bend and are thus better suited to create quick and accurate [[wrist shot]]s, as well as improving passing and stickhandling.
Stick flex is viewed as a very important characteristic by most players. Commonly, [[defenceman (ice hockey)|defencemen]] seek stiffer flex shafts, as their greater stiffness imparts more force on slap shots and improves [[checking (ice hockey)|stick-checking]]. Forwards will commonly seek more flexible shafts, as they require less force to bend and are thus better suited to create quick and accurate [[wrist shot]]s, as well as improving passing and stickhandling.
Line 93: Line 91:
Until the early 1960s, hockey stick blades were typically not curved. However, in the late 1950s, [[New York Rangers]] center [[Andy Bathgate]] began experimenting with "breaking" his stick blades to impart a curve, which he found made his slap shots behave in highly erratic ways. Soon after [[Chicago Blackhawks]] forwards [[Stan Mikita]] and [[Bobby Hull]] stumbled onto the "broken blade", and subsequently began asking their stick manufacturers to create sticks with pre-curved blades.
Until the early 1960s, hockey stick blades were typically not curved. However, in the late 1950s, [[New York Rangers]] center [[Andy Bathgate]] began experimenting with "breaking" his stick blades to impart a curve, which he found made his slap shots behave in highly erratic ways. Soon after [[Chicago Blackhawks]] forwards [[Stan Mikita]] and [[Bobby Hull]] stumbled onto the "broken blade", and subsequently began asking their stick manufacturers to create sticks with pre-curved blades.


Soon after, much of the [[NHL]], and Hull in particular, became a proponents of the "banana blade", or stick with extreme amounts (often up to 3 inches) of curve in the blade. These curves made shots behave very strangely, especially slap shots. In an era in which goalies did not wear masks, this eventually became an unacceptable danger soon golies were forced to wear masks. By [[1967]], the NHL began to limit the amount of curve a stick blade could legally have. In the NHL today, the legal limit is 3/4 of an inch.
Soon after, much of the [[NHL]], and Hull in particular, became a proponents of the "banana blade", or stick with extreme amounts (often up to 3 inches) of curve in the blade. These curves made slap shots behave very erratically, and in an era in which goalies did not wear masks, this eventually became an unacceptable danger. By [[1967]], the NHL began to limit the amount of curve a stick blade could legally have. In the NHL today, the legal limit is 3/4 of an inch.


Much like the shaft's flex, a blade's pattern is a very important characteristic of a stick's performance. There are three primary variables in blade design: curve, face angle, and toe.
Much like the shaft's flex, a blade's pattern is a very important characteristic of a stick's performance. There are three primary variables in blade design: curve, face angle, and toe.
Line 115: Line 113:


===Tape===
===Tape===
The top of the shaft is most commonly wrapped with cloth tape in a manner which improves the grip on stick by the player's top hand. Most players also apply a "knob" of tape which will create a small gap between the shaft and the ice in the event the stick is dropped, making it easier to pick up the stick. Goaltenders often wrap huge "knobs" on the ends of their sticks (sometimes up to two inches across), which makes it easier for them to poke check without losing the stick (as well as making it easier to pick up a dropped stick).
Players usually wrap the top of the shaft and the stick blade with cloth tape up to the top of the stick.

The top of the shaft is most commonly wrapped with cloth tape in a manner which improves the grip on stick by the player's top hand. Most players also apply a "knob" of tape which will create a small gap between the shaft and the ice in the event the stick is dropped, making it easier to pick up the stick. Goaltenders often wrap huge "knobs" on the ends of their sticks (sometimes up to two inches across), which makes it easier for them to poke check without losing the stick (as well as making it easier to pick up a dropped stick). Some goaltenders prefer making huge "knobs" so there's more chance of making a stick save, but if the knob is too big, when the goalie puts his stick on the ice to make a save the puck can slide underneath the space between the stick and the ice. Players commonly use white tape to make the knob, because black tape deteriorates the gloves faster.

The blade of the stick is most commonly wrapped with [[friction tape]], a cotton tape that has been impregnated with adhesive so that it is moderately sticky. This is done to improve puckhandling and to avoid water damage to the stick. Preferred amounts of puck adhesion vary among players; some players will use a regular cloth tape instead of friction tape, while [[Wayne Gretzky]] used friction tape but then applied [[baby powder]] to lower its adhesion.<ref name="Stickstyles">used ref</ref> There is also variation in color, white or black being predominant. Most players prefer black, however.

The most common stick way to tape the stick is to apply tape from the toe to the heel. They either just apply the tape normally, leaving the very tip exposed, but some also rip off a single strip, which they'll put on the bottom of the stick and apply it up to the toe and the strip ending near the top, then they tape the faces of the stick. This extra strip is applied to protect the bottom of the stick, which deteriorates very quickly. This also protects the toe, which commonly gets chipped while playing.

Some less common styles of taping the blade of the stick include

-Leaving a space in the middle: This was commonly used especially during the early days of the game. The players would tape the heel up until about the middle, rip the strip of tape, and then begin taping again about an inch and a half to two inches ahead, then end it at the toe, leaving the one and a half to two inches of the stick exposed. Very few players use it today, but there are some who still use it.

-The Bobby Orr: Bobby Orr used very, very little tape on his blade... usually only one strip of tape in the middle of the stick. Most believe that this increased shot speed, but it's still undetermined.

-Tape near the heel: Another uncommon style of taping the stick, players will only tape the stick near the heel, and end the tape at about the middle of the blade. Players believe this increases stick handling ability and shot speed but, again, this is still undetermined.

-Tape near the toe: Players tape only close to the toe of the stick.


The blade of the stick is most commonly wrapped with [[friction tape]], a cotton tape that has been impregnated with adhesive so that it is moderately sticky. This is done to improve puckhandling and to avoid water damage to the stick. Preferred amounts of puck adhesion vary among players; some players will use a regular cloth tape instead of friction tape, while [[Wayne Gretzky]] used friction tape and then applied [[baby powder]] to lower its adhesion.<ref name="Stickstyles">used ref</ref> There is also variation in color, black being the most common choice.
Another thing players do is apply tape to the shaft of the stick to increase grip. Commonly with white tape, players will wrap the shaft, commonly nearer to the blade, with tape, but some will only use a tiny bit at the bottom (usually only for centerman) but some will tape the entire shaft from the knob to the heel of the blade.


==References==
==References==

Revision as of 14:52, 3 May 2008

Hockey sticks, regular and goalie, measurements in cm.
Mi'kmaq making hockey sticks from hornbeam trees (Carpinus caroliniana) in Nova Scotia about 1890.

Template:Otheruses2

An ice hockey stick is a piece of equipment used in ice hockey to shoot, pass, and carry the puck. Ice hockey sticks are approximately 150-200 cm long, composed of a long, slender shaft with a flat extension at one end called the blade. The blade is the part of the stick used to contact the puck, and is typically 25 to 40 cm long. Stick dimensions can vary widely, as they are usually built to suit a particular player's size and preference. The blade is positioned at roughly a 135° angle from the axis of the shaft, giving the stick a partly 'L-shaped' appearance. The shaft of the stick is fairly rigid, but it has some flexibility to benefit some shots.

The blade is often curved in the direction toward which the skater moves forward, to aid in retaining or lifting the puck off the playing surface.

The goaltender has a slightly modified stick. The lower part of the stick is wider, the angle is smaller, and the blade is slightly curved towards the direction of the play.

History

Hockey sticks were mostly made from the hornbeam tree, which was also a common choice for golf club shafts and wooden tools. However, as hornbeam supplies diminished, it became more cost effective to use other hardwoods, such as yellow birch and ash. Ash gradually became the preferred medium, and by the 1920s an ash hockey stick crafted from a single piece of wood was the type most commonly used. These early sticks were extremely heavy and not very forgiving, although they were extremely durable (Hall of Famer Moose Johnson famously used the same 99 inch stick his entire career).

There were only a handful of major developments in hockey stick technology between the 1920s and the 1980s. Foremost among these was creation of the laminated stick in the 1940s, where layers of wood were glued together and sandwiched to create a more flexible and durable design. In the 1960s, companies began adding an additional lamination of fiberglass or other such synthetic compound as a coating, which further added to the durability and useability of the stick. Also in the 1960s, players began curving the blade of the stick, which dramatically changed the physics affecting players' shots.

In the 1970s, cricket and baseball bat manufacturers began experimenting with lightweight aluminum alloys as a replacement for the traditional willow or ash bat. Hockey stick designers followed suit in the early 1980s, introducing first a single piece all-aluminum stick. This design was not popular, as the stiff aluminum did not have the proper "feel", and so a design featuring an aluminum shaft and a removable, replaceable wooden blade was tried. This became very popular in the late 1980s and early 1990s, challenging the prevalence of the traditional wooden stick for the first time.

In recent years, the aluminum stick, as well as its wooden counterpart, have largely been replaced by more advanced composite designs. Common building materials include fiberglass and carbon fiber, and some manufacturers have even explored using materials as kevlar. Composite sticks generally weigh less than their alumimum forebears, and they can be manufactured with more consistent (and varied) physical properties than their wooden counterparts. They are, however, considerably more expensive than wooden sticks, and are not nearly as durable as the older aluminum sticks

Features

The primary variables of hockey stick design are the lie, flex, and blade pattern, as well as the material used to build the stick.

Building Material

Over the last two decades, there have been tremendous advances in the material technology used to create hockey sticks. Today, the vast majority of sticks are made with one (or a combination) of the following materials:

Wood

Wooden sticks are usually constructed by laminating multiple types of wood into a high quality plywood, then coating the stick and blade with thin plastic or fiberglass. Some manufacturers use fiberglass as a laminate between wood layers. Today in the NHL, only 16 players still use wooden sticks, including Ottawa Senators Jason Spezza and Vancouver Canucks Markus Naslund.

The main advantage that wooden sticks enjoy today is their relatively low cost. Few wooden sticks cost more than $40 per copy, compared to $200+ for some composite varieties. This makes them a popular choice by younger and amateur players. Wooden sticks also enjoy a repuation of having a good "feel" compared to aluminum or titanium choices. The main disadvantage that wooden sticks suffer from is the relative irregularity and poor durability of the wooden construction. Wood has a tendency to warp, and over time its flex and stiffness properties will change. Additionally, being a natural material, wood also creates variations in production (even between identical patterns), and it cannot be made as "responsive" as certain composite materials (which decreases velocity and accuracy on wrist and snap shots).

It is a common misperception that, for most players, aluminum or composite sticks make for harder slap shots. As it relates to slap shots specifically, wooden sticks have very similar properties to composite sticks, and for most players there will be very little difference in velocity between wood and other materials. It should also be noted that the short list of players with the hardest slap shots in NHL history (Bobby Hull, Al MacInnis, Al Iafrate, among others) all used wooden sticks (although of course they did not have access to the composite variety).

Aluminum

Alumimum sticks were the first non-wood sticks to appear. Most aluminum sticks consist of a shaft made of an aluminum alloy and a wooden blade or composite blade, which is held in the shaft by glue and the compression of the shaft itself. There was a time when a majority of NHL players used aluminum sticks, but today around 1% of NHL players use aluminum sticks.

The main advantage aluminum sticks enjoy is their unparalleled durability. It is fairly rare for an aluminum shaft to be broken or damaged, even at the professional level, and since the blades can be easily replaced, a shaft will typically last for a relatively long period of time. Aluminum sticks will not suffer wear or warping like a wooden stick, and they can be manufactured with a great deal of consistency in flex and weight. The biggest disadvantage of aluminum sticks is their heavy or hard "feel", which is a result of the relative hardness of the metal and the imprecise joining of the stick and blade.

Fiberglass

Fiberglass, along with the traditional wood, was the first composite stick material, being added as laminate or coating to wooden sticks. Manufacturers have experimented with 100% fiberglass ice hockey sticks, but they suffered from poor "feel" and poor durability and never really caught on. Currently, there are no 100% fiberglass ice hockey sticks being manufactured (although field hockey sticks are commonly made from pure fiberglass).

Today, fiberglass is most commonly used as a composite with other materials, such as wood, graphite, or kevlar. Generally speaking, a higher fiberglass content in a graphite stick will lessen its production cost and increase its durability, at the expense of its "feel" and flex properties. Thus, "high fiberglass" composite sticks are often good low-cost options for players who want to use composite sticks.

Carbon Fiber

Carbon fiber has become by far the most popular building material for sticks used in the NHL, and it is growing rapidly in popularity for amateur and recreational players. Carbon fiber sticks were originally sold as shafts alone, much like their aluminum counterparts. Very recently, however, "one piece" sticks, which consist of a single piece shaft and blade, have become the predominant type.

Carbon fiber sticks have become so popular due primarily to the way they combine features of wooden and aluminum sticks. They offer the classic "feel" and performance of the best wooden varieties, and the manufacturing consistency and precision of aluminum sticks. They can also be manufactured with extraordinarily precise "flex patterns" which can aid in the power and accuracy of wrist and snap shots, and their manufacturing process makes it extremely simple to add any number of different materials and features which can dramatically change the properties of the stick (a good example of this being the silicon injections made in certain high-end sticks that are claimed to further enhance their "feel").

Their main disadvantage is their high cost coupled with their relatively poor durability. While their average life is not quite as short as their wooden counterparts, it is poor enough that competitive senior players will usually break one every week or two, which for an entire team over the course of a season can become extremely expensive. This can be a particularly nasty burden for "nonprofit" competitive teams (such as college hockey teams in the United States), some of whom have begun restricting their players from using the most expensive composite sticks.

Kevlar

Kevlar, most commonly known as a bulletproof material, has become a fairly common component of composite sticks. Originally added to increase the durability of aluminum stick blades, it became an ideal addition to the more fragile wooden and carbon fiber sticks, and today it is a material used by nearly every manufacturer. It is a useful component as it dramatically increases the durability of the stick without significantly compromising its weight, feel, or flex properties.

Titanium

Titanium sticks are a fairly new development, and are both extremely rare and extremely expensive. They are usually just a shaft, which will be coupled with a wooden or carbon blade in much the same manner as an aluminum stick. Other sticks have titanium added as a composite material to carbon fiber or kevlar.

Titanium is similar to aluminum in general properties, although it is lighter, stronger, and is said to have notably superior "flex" properties (due mainly to the relative thinness of the walls of the shaft).

Stick Properties

Lie

The lie of a stick refers to the angle between the shaft and the blade. A lie value of 5 corresponds to a 135° angle, and each additional lie value corresponds to a 2° smaller angle.[1] With the bottom of the blade flat on the ice, a higher lie value causes the shaft to stand up straighter. Typical values range from 5 to 7; most sticks now are near 5.5. Goalie sticks typically have a lie between 11 and 15.[2]

Players usually seek a lie that will put the blade flat on the ice while they are in their typical skating stance. Hall of Fame center Wayne Gretzky, for example, used a stick with a low lie to correspond with his deep skating crouch and shorter height, whereas Hall of Fame defenceman Rod Langway used a stick with a very high lie number as he was very tall and tended to skate in a very upright position.

Flex

A used Royale Warrior hockey stick with a flex of 50.

Hockey stick shafts, much like golf club shafts, are highly flexible, and this flexibility is a key component in their performance. Flex, bend, stiffness, and whip are all terms used to describe the amount force required to bend a given stick shaft a certain amount.

With most composite and alumimum sticks, their flex characteristic is correlated numerically. This number, which ranges from 50 through 120, is printed on the stick and corresponds to the amount force (in pounds-force) that it takes to deflect or bend the shaft one inch. For example, a 100 flex requires 100 pounds force (444 N) to bend the shaft 1 inch.

Stick flex is viewed as a very important characteristic by most players. Commonly, defencemen seek stiffer flex shafts, as their greater stiffness imparts more force on slap shots and improves stick-checking. Forwards will commonly seek more flexible shafts, as they require less force to bend and are thus better suited to create quick and accurate wrist shots, as well as improving passing and stickhandling.

Flex is also correlated to player strength; stronger players will often prefer stiffer flexes, as they have a sufficient amount of strength to fully bend (and thus maximize potential energy) using such shafts, whereas younger players and players with less strength will generally have more success using more flexible shafts which they are capable of bending to their optimal degree.

Blade pattern

Until the early 1960s, hockey stick blades were typically not curved. However, in the late 1950s, New York Rangers center Andy Bathgate began experimenting with "breaking" his stick blades to impart a curve, which he found made his slap shots behave in highly erratic ways. Soon after Chicago Blackhawks forwards Stan Mikita and Bobby Hull stumbled onto the "broken blade", and subsequently began asking their stick manufacturers to create sticks with pre-curved blades.

Soon after, much of the NHL, and Hull in particular, became a proponents of the "banana blade", or stick with extreme amounts (often up to 3 inches) of curve in the blade. These curves made slap shots behave very erratically, and in an era in which goalies did not wear masks, this eventually became an unacceptable danger. By 1967, the NHL began to limit the amount of curve a stick blade could legally have. In the NHL today, the legal limit is 3/4 of an inch.

Much like the shaft's flex, a blade's pattern is a very important characteristic of a stick's performance. There are three primary variables in blade design: curve, face angle, and toe.

The curve refers to the basic amount the blade curves from toe to heel, as well as the part of the blade where that curve is located. A "toe curve" means that the curve is concentrated near the toe of the blade, and it is usually preferred by forwards, who seek better puckhandling and more accurate wrist shots. A "heel curve" is generally better for slap shots, and is thus used more by defencemen.

Face angle is the angle between the ice surface and the front surface of the blade (this characteristic is comparable to the difference between the different irons in golf). A more "open" blade means that the face of the blade is turned up more sharply, and thus will cause a higher trajectory than a "closed" face angle.

The toe shape refers to the basic shape of the end of the blade, and it is typically either round or square. Square toes make it easier to pull a puck off the boards or to do "toe fakes" (stickhandling moves using the toe of the blade), whereas round toes make it easier to "flip" the puck, and also offer slight advantages in basic puckhandling.

Blades also differ in length and thickness, based on player preference.

Illegal curves

The curve of a blade is limited at most levels of competitive hockey, generally to an amount between 1/2 and 3/4 of an inch. Hasty measurements can be made by attempting to roll a dime under the blade placed face down on the ice, but accurate measurements require a "stick gauge" which measures curve precisely. Currently, the NHL limits blade curvature to 3/4 of an inch. Being caught using an illegal stick is typically punished with a two minute minor penalty.

The genesis for this rule was the "banana blade" of the 1960s. At the height of this era, players would often simply cross the blue line and let fly with a slap shot, hoping that the bizarre behavior of the puck would beat the goaltender. Goaltenders, who often did not wear masks in this era, were irritated by the danger such wild shots posed to them and in response, the NHL began gradually reducing the amount of curve a blade could legally have.

In the modern game, the emphasis on shooting accuracy has largely eliminated any preference for extreme blade curves. However, hockey still retains illegal stick rules, which has become a cause of debate. The argument is that since blade curvature does not impart any significant advantage, that penalizing it is unnecessary. Additionally, coaches have used the "illegal equipment" penalty at key moments in games to win a power play, and in some cases, swing the momentum of entire series.

The most notorious such incident occurred in Game 2 of the 1993 Stanley Cup Finals. The Montreal Canadiens, down 1-0 in the series, were losing to the Los Angeles Kings 2-1 late in the third period when coach Canadiens Jacques Demers called for a measurement on Kings' defenceman Marty McSorley's stick. McSorley's stick was found to be illegal, and he was assessed a minor penalty. Canadiens defenceman Eric Desjardins scored on the power play, and then again in overtime, which gave the Canadiens the win. The Canadiens would go on to win the series in 5 games.

Tape

The top of the shaft is most commonly wrapped with cloth tape in a manner which improves the grip on stick by the player's top hand. Most players also apply a "knob" of tape which will create a small gap between the shaft and the ice in the event the stick is dropped, making it easier to pick up the stick. Goaltenders often wrap huge "knobs" on the ends of their sticks (sometimes up to two inches across), which makes it easier for them to poke check without losing the stick (as well as making it easier to pick up a dropped stick).

The blade of the stick is most commonly wrapped with friction tape, a cotton tape that has been impregnated with adhesive so that it is moderately sticky. This is done to improve puckhandling and to avoid water damage to the stick. Preferred amounts of puck adhesion vary among players; some players will use a regular cloth tape instead of friction tape, while Wayne Gretzky used friction tape and then applied baby powder to lower its adhesion.[3] There is also variation in color, black being the most common choice.

References

  1. ^ "Hockey Stick Sizing Guide at prohockeystuff.com". Retrieved 2007-02-25.
  2. ^ "How To Buy a Hockey Stick at MVP.com". Retrieved 2007-02-25.
  3. ^ used ref