Lenticular printing
![](http://upload.wikimedia.org/wikipedia/commons/thumb/4/46/Close_up_of_the_surface_of_a_lenticular_print.jpg/330px-Close_up_of_the_surface_of_a_lenticular_print.jpg)
Lenticular printing is a technology in which a lenticular lens is used to produce images with an illusion of depth, or the ability to change or move as the image is viewed from different angles. Examples of lenticular printing include prizes given in Cracker Jack snack boxes that showed flip and animation effects such as winking eyes, and modern advertising graphics that change their message depending on the viewing angle. This technology was created in the 1940s but has evolved in recent years to show more motion and increased depth. Originally used mostly in novelty items and commonly called "flicker pictures" or "wiggle pictures," lenticular prints are now being used as a marketing tool to show products in motion. Recent advances in large-format presses have allowed for oversized lenses to be used in lithographic lenticular printing.[1]
Process
Lenticular printing is a multi-step process consisting of creating a lenticular image from at least two images, and combining it with a lenticular lens. This process can be used to create various frames of animation (for a motion effect), offsetting the various layers at different increments (for a 3D effect), or simply to show a set of alternate images which may appear to transform into each other. Once the various images are collected, they are flattened into individual, different frame files, and then digitally combined into a single final file in a process called interlacing.
From there the interlaced image can be printed directly to the back (smooth side) of the lens or it can be printed to a substrate (ideally a synthetic paper) and laminated to the lens. When printing to the backside of the lens, the critical registration of the fine "slices" of interlaced images must be absolutely correct during the lithographic or screen printing process or "ghosting" and poor imagery might result.
The combined lenticular print will show two or more different images simply by changing the angle from which the print is viewed. If more (30+) images are used, taken in a sequence, one can even show a short video of about one second. Though normally produced in sheet form, by interlacing simple images or different colors throughout the artwork, lenticular images can also be created in roll form with 3D effects or multi-color changes. Alternatively, one can use several images of the same object, taken from slightly different angles, and then create a lenticular print which shows a stereoscopic 3D effect. 3D effects can only be achieved in a side to side (left to right) direction, as the viewer's left eye needs to be seeing from a slightly different angle than the right to achieve the stereoscopic effect. Other effects, like morphs, motion, and zooms work better (less ghosting or latent effects) as top-to-bottom effects, but can be achieved in both directions.
There are several film processors that will take two or more pictures and create lenticular prints for hobbyists, at a reasonable cost. For slightly more money one can buy the equipment to make lenticular prints at home. This is in addition to the many corporate services that provide high volume lenticular printing.
There are many commercial end uses for lenticular images, which can be made from PVC, APET, acrylic, and PETG, as well as other materials. While PETG and APET are the most common, other materials are becoming popular to accommodate outdoor use and special forming due to the increasing use of lenticular images on cups and gift cards. Lithographic lenticular printing allows for the flat side of the lenticular sheet to have ink placed directly onto the lens, while high-resolution photographic lenticulars typically have the image laminated to the lens.
Recently, large format (over 2m) lenticular images have been used in bus shelters and movie theaters. These are printed using an oversized lithographic press. Many advances have been made to the extrusion of lenticular lens and the way it is printed which has led to a decrease in cost and an increase in quality. Lenticular images have recently seen a surge in activity, from gracing the cover of the May 2006 issue of Rolling Stone to trading cards, sports posters and signs in stores that help to attract buyers.
The newest lenticular technology is manufacturing lenses with flexo, inkjet and screen-printing techniques. The lens material comes in a roll or sheet which is fed through flexo or offset printing systems at high speed, or printed with UV inkjet machines (usually flat-beds that enable a precise registration). This technology allows high volume 3D lenticular production at low cost. Because, at the beginning of the story, this new technique only allowed to create non contiguous lenses, the only effect available was the 3D effect with a repeating pattern (moiré).
Construction
![](http://upload.wikimedia.org/wikipedia/en/0/09/Sq3d-Entrelacage.png)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/f/fd/How_a_lenticular_lens_works.png/220px-How_a_lenticular_lens_works.png)
Each image is arranged (slicing) into strips, which are then interlaced with one or more similarly arranged images (splicing). These are printed on the back of a piece of plastic, with a series of thin lenses molded into the opposite side. Alternatively, the images can be printed on paper, which is then bonded to the plastic. With the new technology, lenses are printed in the same printing operation as the interlaced image, either on both sides of a flat sheet of transparent material, or on the same side of a sheet of paper, the image being covered with a transparent sheet of plastic or with a layer of transparent, which in turn is printed with several layers of varnish to create the lenses.
The lenses are accurately aligned with the interlaces of the image, so that light reflected off each strip is refracted in a slightly different direction, but the light from all pixels originating from the same original image is sent in the same direction. The end result is that a single eye looking at the print sees a single whole image, but two eyes will see different images, which leads to stereoscopic 3D perception.
Types of lenticular prints
There are three distinct types of lenticular print, distinguished by how great a change in angle of view is required to change the image:
- Transforming prints
- Here two or more very different pictures are used, and the lenses are designed to require a relatively large change in angle of view to switch from one image to another. This allows viewers to easily see the original images, since small movements cause no change. Larger movement of the viewer or the print causes the image to flip from one image to another. (The "flip effect".)
- Animated prints
- Here the distance between different angles of view is "medium", so that while both eyes usually see the same picture, moving a little bit switches to the next picture in the series. Usually many sequential images would be used, with only small differences between each image and the next. This can be used to create an image that moves ("motion effect"), or can create a "zoom" or "morph" effect, in which part of the image expands in size or changes shape as the angle of view changes. The movie poster of the film Species II, shown in this article, is an example of this technique.
- Stereoscopic effects
- Here the change in viewing angle needed to change images is small, so that each eye sees a slightly different view. This creates a 3D effect without requiring special glasses.
Motorized lenticular
The basic idea of motorized lenticular displays is simple. With static (non-motorized) lenticular, the viewer either moves the piece or moves past the piece in order to see the graphic effects. With motorized lenticular, a motor moves the graphics behind the lens, enabling the graphic effects while both the viewer and the display remain stationary.
History of lenticular image technology
Images that change when viewed from different angles predate the development of lenticular lenses. In 1692 G. A. Bois-Clair, a French painter, created paintings containing two distinct images, with a grid of vertical laths in front.[2] Different images were visible when the work was viewed from the left and right sides.
![](http://upload.wikimedia.org/wikipedia/en/thumb/5/5f/Saturnalia.jpg/220px-Saturnalia.jpg)
![](http://upload.wikimedia.org/wikipedia/en/thumb/1/1e/Rolux.jpg/220px-Rolux.jpg)
![](http://upload.wikimedia.org/wikipedia/en/thumb/6/6e/Duflex.jpg/220px-Duflex.jpg)
Lenticular images were popularized from the late 1940s to the mid 1980s by the Vari-Vue company.[3] Early products included animated political campaign badges with the slogan "I Like Ike!" and animated cards that were stuck on boxes of Cheerios.[3] By the late sixties the company marketed about two thousand stock products including twelve inch square moving pattern and color sheets, large images (many religious), and a huge range of novelties including badges. The badge products included the Rolling Stones' tongue logo and an early Beatles badge with pictures of the 'fab four' on a red background.
Some notable lenticular prints from this time include the limited-edition cover of the Rolling Stones' Their Satanic Majesties Request, and Saturnalia's Magical Love, a picture disk with a lenticular center. Several magazines including Look and Venture published issues in the 1960s that contained lenticular images. Many of the magazine images were produced by Crowle Communications (also known as Visual Panographics). Images produced by the company ranged from just a few millimeters to 28 by 19.5 inches.
The panoramic cameras used for most of the early lenticular prints were French-made and weighed about 300 pounds. In the 1930s they were known as "auto-stereo cameras". These wood and brass cameras had a motorized lens that moved in a semicircle around the lens' nodal point. Sheet transparency film with the lenticular lens overlay was loaded into special dark slides (about 10×15 inches) and these were then inserted into the camera. The exposure time was several seconds long, giving time for the motor drive to power the lens around in an arc.[citation needed]
A related product produced by a small company in New Jersey was Rowlux. Unlike the Vari-Vue product, Rowlux used a microprismatic lens structure made by a process they patented in 1972,[4] and no paper print. Instead, the plastic (Polycarbonate, flexible PVC and later PETG) was dyed with translucent colors and the film was usually thin and flexible (from 0.002" in thickness).
Lenticular arrays are also used for 3D television (autostereoscopic, enabling the 3D perception without glasses), and number of prototypes have been shown in 2009 2010 by major companies such as Philips and LG. They are using cylindrical lenses slanted to the vertical, or spherical lenses arranged as a honeycomb which provides a better resolution.
While not a true lenticular, the Dufex Process (Manufactured by F.J. Warren Ltd.)[5] does use a form of lens structure to animate the image. The process consists of a metallic foil imprinted by litho printing with the image. The foil is than laminated to a thin sheet of card stock that has had a thick layer of wax coated upon it. The heated lamination press has the Dufex embossing plate on its upper platen. The plate has been engraved with angled 'lenses' at different angles so designed as to match the artwork and reflect light at different intensities depending on angle of view.
Manufacturing process
Designing and manufacturing a lenticular product requires a sound knowledge of optics, binocular vision, computing, the graphic chain, and also stringency in work and precision throughout the manufacturing process.
Printing
Creation of lenticular images in volume requires printing presses that are adapted to print on sensitive thermoplastic materials. Lithographic offset printing is typically used, to ensure the images are good quality. Printing presses for lenticulars must be capable of adjusting image placement in 10 µm steps, to allow good alignment of the image to the lens array.
Typically, ultraviolet-cured inks are used. These dry very quickly by direct conversion of the liquid ink to a solid form, rather than by evaporation of liquid solvents from a mixture. Powerful (400W per sq. in) ultraviolet (UV) lamps are used to rapidly cure the ink. This allows lenticular images to be printed at high speed.
In some cases, electron beam lithography is used instead. The curing of the ink is then initiated directly by an electron beam scanned across the surface.
Defects
Design defects
- Double images on the relief and in depth
Double images are usually caused by an exaggeration of the 3-D effect from angles of view or an insufficient number of frames. Poor design can lead to doubling, small jumps, or a fuzzy image, especially on objects in relief or in depth. For some visuals, where the foreground and background are fuzzy or shaded, this exaggeration can prove to be an advantage. In most cases, the detail and precision required do not allow this.
- Image ghosting
Ghosting occurs due to poor treatment of the source images, and also due to transitions where demand for an effect goes beyond the limits and technical possibilities of the system. This causes some of the images to remain visible when they should disappear. These effects can depend on the lighting of the lenticular print.
Prepress defects
- Synchronisation of the print (master) with the pitch
Also known as "Banding". Poor calibration of the material can cause the passage from one image to another to not be simultaneous over the entire print. The image transition progresses from one side of the print to the other, giving the impression of a veil or curtain crossing the visual. This phenomenon is felt less for the 3-D effects, but is manifested by a jump of the transverse image. In some cases, the transition starts in several places and progresses from each starting point towards the next, giving the impression of several curtains crossing the visual, as described above.
- Discordant harmonics
This phenomenon is unfortunately very common, and is explained either by incorrect calibration of the support or by incorrect parametrisation of the prepress operations. It is manifested in particular by streaks that appear parallel to the lenticules during transitions from one visual to the other.
Printing defects
- Colour synchronisation
One of the main difficulties in lenticular printing is colour synchronisation. The causes are varied, they may come from a malleable material, incorrect printing conditions and adjustments, or again a dimensional differential of the engraving of the offset plates in each colour.
This poor marking is shown by doubling of the visual; a lack of clarity; a streak of colour or wavy colours (especially for four-colour shades) during a change of phase by inclination of the visual.
- Synchronisation of parallelism of the printing to the lenticules
The origin of this problem is a fault in the printing and forcibly generates a phase defect. The passage from one visual to another must be simultaneous over the entire format. But when this problem occurs, there is a lag in the effects on the diagonals. At the end of one diagonal of the visual, we have one effect, and at the other end we have another.
- Phasing
In most cases, the problem comes from imprecise cutting of the material, as explained below. Nevertheless, poor printing and rectification conditions may also be behind it.
In theory, for a given angle of observation, one and the same visual must appear, for the entire batch. As a general rule, the angle of vision is around 45°, and this angle must be in agreement with the sequence provided by the master. If the images have a tendency to double perpendicularly (for 3-D) or if the images provided for observation to the left appear to the right (top/bottom), there is a phasing problem.
Cutting defects
Defects in the way the lenticular lens is cut lead to phase errors between the lens and the image.
Two examples, taken from the same production batch:
![]() |
![]() |
The first image shows a cut which removed about 150 µm of the first lens, and which shows irregular cutting of the lenticular lenses. The second image shows a cut which removed about 30 µm of the first lens. Defects in cutting such as these lead to a serious phase problem. In the printing press the image being printed is aligned relative to the edges of the sheet of material. If the sheet is not always cut in the same place relative to the first lenticule, a phase error is introduced between the lenses and the image slices.
Consumer prices and availabilitly
For a long time the complex production process of a lenticular picture was only possible in Japan.[citation needed] In recent years, the prices for lenticular-photo printers have decreased, so now smaller photo laboratories are also able to equip themselves with these devices. They can offer to produce 3d prints for individuals or businesses needing only smaller quantities. It needs about three and a half minutes to print a 5.9 x 8.7 inch picture.[6] The prices ranges between six and fifteen dollars for one picture of this size.[citation needed]
See also
- Integral imaging, the precursor of lenticular imaging
- Autostereoscopy
- Parallax barrier
Notes and references
- ^ O'Brien, Katherine (2006). "As big as all outdoors". American Printer (August 1, 2006). Retrieved 2008-06-04.
- ^ Oster, Gerald (1965). "Optical Art" (subscription required). Applied Optics. 4 (11): 1359–69. doi:10.1364/AO.4.001359.
- ^ a b Lake, Matt (1999-05-20). "An art form that's precise but friendly enough to wink". New York Times. Retrieved 2008-06-04.
- ^ US patent 3689346, Rowland, William P., "Method for producing retroreflective material", issued 1972-09-05, assigned to Rowland Development Corp.
- ^ "F.J. Warren Ltd". Kompass UK. Retrieved 2008-06-04.
- ^ "erstes 3D Fachlabor in Deutschland (First 3D photo laboratory in Germany)". Retrieved 2011-01-18.
- Bordas Encyclopedia: Organic Chemistry (French).
- Sirost, Jean-Claude (2007). L'Offset : Principes, Technologies, Pratiques (in French) (2nd ed.). Dunod. ISBN 2100513664.
- Okoshi, Takanori Three-Dimensional Imaging Techniques Atara Press (2011), ISBN 978-0-9822251-4-1
External links
- Lecture slides covering lenticular lenses (PowerPoint) by John Canny
- More on how it works