Paper-based microfluidics
Development of paper-based microfluidic devices began in the early 21st century to meet an increasing need for portable, cheap, and user-friendly medical diagnostic systems. These devices typically consist of a series of hydrophilic cellulose or nitrocellulose fibers that guide liquid from an inlet to a desired outlet by imbibition.
Device Architecture
Paper-based microfluidic devices feature the following regions:[1]
- Inlet: a substrate (typically cellulose) where liquids are dispensed manually.
- Channels: hydrophilic sub-millimeter networks that guide liquid throughout a device.
- Barriers: hydrophobic regions that prevent fluid from leaving the channel.
- Outlets: location where a chemical or biochemical reaction takes place.
Device Flow
The movement of fluid through a porous medium such as paper is governed by permeability[disambiguation needed], geometry and evaporation effects. Collectively these factors results in evaporation limited capillary penetration that can be tuned by controlling porosity and device geometry [2]. Paper is a porous medium in which fluid is transported primarily by wicking and evaporation.[3] The capillary flow during wetting can be approximated by Washburn's equation,[4] which is derived from Jurin's Law and the Hagen–Poiseuille equation.[5] The average velocity of fluid flow is generalized as,where is the surface tension, the contact angle, is the viscosity, and is the distance traveled by the liquid. More extensive models account for paper tortuosity,[6] pore radius, and paper deformation.[7]
Once the medium is fully wetted, subsequent flow is laminar and follows Darcy's Law.[8] The average velocity of fluid flow is generalized as,where is the medium permeability and is the pressure gradient.[9] One consequence of laminar flow is that mixing is difficult and based solely on diffusion, which is slower in porous systems.[10]
Manufacturing techniques
Microfluidic devices can be manufactured using variations of wax printing, inkjet printing, photolithography, flexographic printing, plasma treatment, laser treatment, wet etching[disambiguation needed], screen printing and wax screening.[11] Each technique aims to create hydrophobic physical barriers on hydrophilic paper that passively transport aqueous solutions.[12] Biological and chemical reagents must then be deposited selectively along the device by either dipping the substrate into a reagent solution or locally spotting a reagent onto the substrate.[13]
Wax printing
Wax printing uses a simple printer to pattern wax on paper in a desired design. The wax is then melted with a hotplate to create channels.[14] This technique is fast and low cost, but has relatively low resolution due to the isotropy of the melted wax.
Inkjet printing
Inkjet printing requires coating paper in a hydrophobic polymer, and then selectively placing an ink that etches the polymer to reveal paper.[15] This technique is low cost with high resolution, but is limited by the speed of placing one ink droplet at a time.
Photolithography
Photolithographic techniques are similar to inkjet printing, using a photomask to selectively etch a photoresist polymer.[16] This technique has high resolution and is quick, but has high equipment and material costs.
Applications
Overview
The main advantage of paper-based microfluidic devices over traditional microfluidics devices is their potential for use in the field rather than in a laboratory.[17][18] Filter paper is advantageous in a field setting because it is capable of removing contaminants from the sample and preventing them from moving down the microchannel. This means that particles will not inhibit the accuracy of paper-based assays when they are used outdoors.[18] Paper-based microfluidic devices are also small in size (approximately a few mm to 2 cm in length and width)[18][19][20] compared to other microfluidic platforms, such as droplet-based microfluidic devices, which often use glass slides up to 75 mm in length.[21][22] Because of their small size and relatively durable material, paper-based microfluidic devices are portable.[17][18] Paper-based devices are also relatively inexpensive. Filter paper is very cheap, and so are most of the patterning agents used in the fabrication of microchannels, including PDMS and wax. Most of the major paper-based fabrication methods also do not require expensive laboratory equipment.[17] These characteristics of paper-based microfluidics make it ideal for point-of-care testing, particularly in countries that lack advanced medical diagnostic tools.[18] Paper-based microfluidics has also been used to conduct environmental and food safety tests.[23][24][25][26]
Point-of-care testing: glucose detection
Paper-based microfluidic devices have been designed to monitor a wide variety of medical ailments. Glucose plays an important role in diabetes and cancer,[27] and it can be detected through a catalytic cycle involving glucose oxidase, hydrogen peroxide, and horseradish peroxidase that initiates a reaction between glucose and a color indicator, frequently potassium iodide, on a paper-based microfluidic device.[27] This is an example of colorimetric detection. The first paper-based microfluidic device, developed by George Whitesides’ group at Harvard, was able to simultaneously detect protein as well as glucose via color-change reactions (potassium iodide reaction for glucose and tetrabromophenol blue reaction for the protein BSA).[18] The bottom of the paper device is inserted into a sample solution prepared in-lab, and the amount of color change is observed.[18] More recently, a paper-based microfluidic device using colorimetric detection was developed to quantify glucose in blood plasma. Blood plasma is separated from whole blood samples on a wax-printed device, where red blood cells are agglutinated by antibodies and the blood plasma is able to flow to a second compartment for the color-change reaction.[19] Electrochemical detection[28] has also been used in these devices. It provides greater sensitivity in quantification, whereas colorimetric detection is primarily used for qualitative assessments.[17][27] Screen-printed electrodes[29] and electrodes directly printed on filter paper[30] have been used. One example of a paper-based microfluidic device utilizing electrochemical detection has a dumbbell shape to isolate plasma from whole blood.[30] The current from the hydrogen peroxide produced in the aforementioned catalytic cycle is measured and converted into concentration of glucose.[30]
3D devices for glucose detection
Whitesides’ group also developed a 3D paper-based microfluidic device for glucose detection that can produce calibration curves on-chip because of the improved fluid flow design.[31] This 3D device consists of layers of paper patterned with microfluidic channels that are connected by layers of double-sided adhesive tape with holes. The holes in the tape permit flow between channels in alternating layers of paper, so this device allows for more complicated flow paths and enables the detection of multiple samples in a large number (up to ~1,000) of detection zones in the last layer of paper.[31] More recently, 3D paper-based microfluidic devices assembled using origami were developed.[32] Unlike Whitesides’ design, these devices utilize a single layer of patterned paper that is then folded into multiple layers before sample solution is injected into the device.[32] Subsequently, the device can be unfolded, and each layer of the device can be analyzed for the simultaneous detection of multiple analytes.[32] This device is simpler and less expensive to fabricate than the aforementioned device using multiple layers of paper.[31][32] Mixing between the channels in the different layers was not an issue in either device, so both devices were successful in quantifying glucose and BSA in multiple samples simultaneously.[31][32]
Environmental and food safety tests
Paper-based microfluidic devices have several applications outside of the medical field. For example, paper-based microfluidics has been used extensively in environmental monitoring.[23][24][25][26] Two recent devices were developed for the detection of Salmonella[24] and E. coli[23]. The latter device was specifically used to detect E. coli in seven field water samples from Tucson, Arizona.[23] Antibody-conjugated polystyrene particles were loaded in the middle of the microfluidic channel, after the sample inlet. Immunoagglutination occurs when samples containing Salmonella or E. coli, respectively, come into contact with these particles.[23][24] The amount of immunoagglutination can be correlated with increased Mie scattering of light, which was detected with a specialized smartphone application under ambient light.[23][24] Paper-based microfluidics has also been used to detect pesticides in food products, such as apple juice and milk.[25] A recent design used piezoelectric inkjet printing to imprint paper with the enzyme acetylcholinesterase (AChE) and the substrate indophenyl acetate (IPA), and this paper-based microfluidic device was used to detect organophosphate pesticides (AChE inhibitors) via a decrease in blue-purple color.[25] This device is distinguished by its use of bioactive paper instead of compartments with pre-stored reagents, and it was demonstrated to have good long-term stability, making it ideal for field use.[25] A more recent paper-based microfluidic design utilized a sensor, consisting of fluorescently labeled single-stranded DNA (ssDNA) coupled with graphene oxide, on its surface to simultaneously detect heavy metals and antibiotics in food products.[26] Heavy metals increased fluorescence intensity, whereas antibiotics decreased fluorescence intensity.[26]
References
- ^ Berthier, Jean; Brakke, Kenneth A.; Berthier, Erwin (2016). Open Microfluidics. John Wiley & Sons, Inc. pp. 229–256. doi:10.1002/9781118720936.ch7/summary. ISBN 9781118720936.
- ^ Liu, M.; et al. (2018). "Tuning capillary penetration in porous media: Combining geometrical and evaporation effects" (PDF). International Journal of Heat and Mass Transfer. 123: 239–250. doi:10.1016/j.ijheatmasstransfer.2018.02.101.
{{cite journal}}
: Explicit use of et al. in:|last2=
(help) - ^ Dixit, Chandra K.; Kaushik, Ajeet (2016-10-13). Microfluidics for Biologists: Fundamentals and Applications. Springer. ISBN 9783319400365.
- ^ Masoodi, Reza; Pillai, Krishna M. (2012-10-26). Wicking in Porous Materials: Traditional and Modern Modeling Approaches. CRC Press. ISBN 9781439874325.
- ^ Washburn, Edward W. (1921-03-01). "The Dynamics of Capillary Flow". Physical Review. 17 (3): 273–283. doi:10.1103/PhysRev.17.273.
- ^ Cai, Jianchao; Yu, Boming (2011-09-01). "A Discussion of the Effect of Tortuosity on the Capillary Imbibition in Porous Media". Transport in Porous Media. 89 (2): 251–263. doi:10.1007/s11242-011-9767-0. ISSN 0169-3913.
- ^ Berthier, Jean; Brakke, Kenneth A. The Physics of Microdroplets - Berthier - Wiley Online Library. doi:10.1002/9781118401323.
- ^ Bejan, Adrian (2013). Convection Heat Transfer. John Wiley & Sons, Inc. pp. i–xxxiii. doi:10.1002/9781118671627.fmatter/pdf. ISBN 9781118671627.
- ^ Darcy, Henry (1856). Les fontaines publiques de la ville de Dijon. Exposition et application des principes à suivre et des formules à employer dans les questions de distribution d'eau: ouvrage terminé par un appendice relatif aux fournitures d'eau de plusieurs villes au filtrage des eaux et à la fabrication des tuyaux de fonte, de plomb, de tole et de bitume (in French). Dalmont.
- ^ Diffusion in Natural Porous Media - Contaminant Transport, | Peter Grathwohl | Springer.
- ^ "Paper microfluidic devices : A review 2017 - Elveflow". Elveflow. Retrieved 2018-02-06.
- ^ Galindo-Rosales, Francisco José (2017-05-26). Complex Fluid-Flows in Microfluidics. Springer. ISBN 9783319595931.
- ^ Yamada, Kentaro; Shibata, Hiroyuki; Suzuki, Koji; Citterio, Daniel (2017-03-29). "Toward practical application of paper-based microfluidics for medical diagnostics: state-of-the-art and challenges". Lab on a Chip. 17 (7). doi:10.1039/C6LC01577H. ISSN 1473-0189.
- ^ Carrilho, Emanuel; Martinez, Andres W.; Whitesides, George M. (2009-08-15). "Understanding Wax Printing: A Simple Micropatterning Process for Paper-Based Microfluidics". Analytical Chemistry. 81 (16): 7091–7095. doi:10.1021/ac901071p. ISSN 0003-2700.
- ^ Yamada, Kentaro; Henares, Terence G.; Suzuki, Koji; Citterio, Daniel (2015-04-27). "Paper-Based Inkjet-Printed Microfluidic Analytical Devices". Angewandte Chemie International Edition. 54 (18): 5294–5310. doi:10.1002/anie.201411508. ISSN 1521-3773.
- ^ "Development of paper-based microfluidic analytical device for iron assay using photomask printed with 3D printer for fabrication of hydrophilic and hydrophobic zones on paper by photolithography". Analytica Chimica Acta. 883: 55–60. 2015-07-09. doi:10.1016/j.aca.2015.04.014. ISSN 0003-2670.
- ^ a b c d Li, Xu; Ballerini, David R.; Shen, Wei (2012-03-02). "A perspective on paper-based microfluidics: Current status and future trends". Biomicrofluidics. 6 (1): 011301–011301–13. doi:10.1063/1.3687398. ISSN 1932-1058. PMC 3365319. PMID 22662067.
- ^ a b c d e f g Martinez, Andres W.; Phillips, Scott T.; Butte, Manish J.; Whitesides, George M. (2007). "Patterned paper as a platform for inexpensive, low-volume, portable bioassays". Angewandte Chemie (International Ed. in English). 46 (8): 1318–1320. doi:10.1002/anie.200603817. ISSN 1433-7851. PMC 3804133. PMID 17211899.
- ^ a b Yang, Xiaoxi; Forouzan, Omid; Brown, Theodore P.; Shevkoplyas, Sergey S. (2012-01-21). "Integrated separation of blood plasma from whole blood for microfluidic paper-based analytical devices". Lab on a Chip. 12 (2): 274–280. doi:10.1039/c1lc20803a. ISSN 1473-0189. PMID 22094609.
- ^ Yu, Jinghua; Ge, Lei; Huang, Jiadong; Wang, Shoumei; Ge, Shenguang (2011-04-07). "Microfluidic paper-based chemiluminescence biosensor for simultaneous determination of glucose and uric acid". Lab on a Chip. 11 (7): 1286–1291. doi:10.1039/c0lc00524j. ISSN 1473-0189. PMID 21243159.
- ^ Clausell-Tormos, Jenifer; Lieber, Diana; Baret, Jean-Christophe; El-Harrak, Abdeslam; Miller, Oliver J.; Frenz, Lucas; Blouwolff, Joshua; Humphry, Katherine J.; Köster, Sarah (May 2008). "Droplet-based microfluidic platforms for the encapsulation and screening of Mammalian cells and multicellular organisms". Chemistry & Biology. 15 (5): 427–437. doi:10.1016/j.chembiol.2008.04.004. ISSN 1074-5521. PMID 18482695.
- ^ Baret, Jean-Christophe; Miller, Oliver J.; Taly, Valerie; Ryckelynck, Michaël; El-Harrak, Abdeslam; Frenz, Lucas; Rick, Christian; Samuels, Michael L.; Hutchison, J. Brian (2009-07-07). "Fluorescence-activated droplet sorting (FADS): efficient microfluidic cell sorting based on enzymatic activity". Lab on a Chip. 9 (13): 1850–1858. doi:10.1039/b902504a. ISSN 1473-0197. PMID 19532959.
- ^ a b c d e f Park, Tu San; Yoon, Jeong-Yeol (2015-03-01). Smartphone Detection of Escherichia coli From Field Water Samples on Paper Microfluidics. Vol. 15.
- ^ a b c d e Park, Tu San; Li, Wenyue; McCracken, Katherine E.; Yoon, Jeong-Yeol (2013-12-21). "Smartphone quantifies Salmonella from paper microfluidics". Lab on a Chip. 13 (24): 4832–4840. doi:10.1039/c3lc50976a. ISSN 1473-0189. PMID 24162816.
- ^ a b c d e Hossain, S. M. Zakir; Luckham, Roger E.; McFadden, Meghan J.; Brennan, John D. "Reagentless Bidirectional Lateral Flow Bioactive Paper Sensors for Detection of Pesticides in Beverage and Food Samples". Analytical Chemistry. 81 (21): 9055–9064. doi:10.1021/ac901714h.
- ^ a b c d Zhang, Yali; Zuo, Peng; Ye, Bang-Ce (2015-06-15). "A low-cost and simple paper-based microfluidic device for simultaneous multiplex determination of different types of chemical contaminants in food". Biosensors & Bioelectronics. 68: 14–19. doi:10.1016/j.bios.2014.12.042. ISSN 1873-4235. PMID 25558869.
- ^ a b c Liu, Shuopeng; Su, Wenqiong; Ding, Xianting (2016-12-08). "A Review on Microfluidic Paper-Based Analytical Devices for Glucose Detection". Sensors. 16 (12): 2086. doi:10.3390/s16122086.
{{cite journal}}
: CS1 maint: unflagged free DOI (link) - ^ Dungchai, Wijitar; Chailapakul, Orawon; Henry, Charles S. "Electrochemical Detection for Paper-Based Microfluidics". Analytical Chemistry. 81 (14): 5821–5826. doi:10.1021/ac9007573.
- ^ Noiphung, Julaluk; Songjaroen, Temsiri; Dungchai, Wijitar; Henry, Charles S.; Chailapakul, Orawon; Laiwattanapaisal, Wanida (2013-07-25). "Electrochemical detection of glucose from whole blood using paper-based microfluidic devices". Analytica Chimica Acta. 788: 39–45. doi:10.1016/j.aca.2013.06.021. ISSN 1873-4324. PMID 23845479.
- ^ a b c Li, Zedong; Li, Fei; Hu, Jie; Wee, Wei Hong; Han, Yu Long; Pingguan-Murphy, Belinda; Lu, Tian Jian; Xu, Feng (2015-08-21). "Direct writing electrodes using a ball pen for paper-based point-of-care testing". The Analyst. 140 (16): 5526–5535. doi:10.1039/c5an00620a. ISSN 1364-5528. PMID 26079757.
- ^ a b c d Martinez, Andres W.; Phillips, Scott T.; Whitesides, George M. (2008-12-16). "Three-dimensional microfluidic devices fabricated in layered paper and tape". Proceedings of the National Academy of Sciences of the United States of America. 105 (50): 19606–19611. doi:10.1073/pnas.0810903105. ISSN 1091-6490. PMC 2604941. PMID 19064929.
- ^ a b c d e Liu, Hong; Crooks, Richard M. "Three-Dimensional Paper Microfluidic Devices Assembled Using the Principles of Origami". Journal of the American Chemical Society. 133 (44): 17564–17566. doi:10.1021/ja2071779.