Jump to content

Railway gun

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by RobDuch (talk | contribs) at 02:40, 4 November 2016 (→World War I: Noted 3 US rwy gun regts in France but not trained by Armistice). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Template:Distinguish2

See also: Armoured train
French 370 mm railway howitzer of World War I

A railway gun, also called a railroad gun, is a large artillery piece, often surplus naval artillery, mounted on, transported by, and fired from a specially designed railway wagon. Many countries have built railway guns, but the best known are the large Krupp-built pieces used by Germany in World War I and World War II. Smaller guns were often part of an armoured train.

Railway guns have been rendered obsolete by advances in technology. Their large size and limited mobility make them vulnerable to attack, and similar payloads can be delivered by aircraft, rocket, or missile.

Design considerations

The design of a railway gun has three issues over and above those of an ordinary artillery piece to consider. Namely how the gun is going to be traversed – i.e. moved from side to side to aim; how the horizontal component of the recoil force will be absorbed by the gun's carriage and how the vertical recoil force will be absorbed by the ground.

Methods of traverse

Non-traversing (top); car traversing mount (middle); top carriage traversing mount (bottom)
British 12-inch howitzers on top-carriage traversing mounts, traversed 90°, Catterick, December 1940

The first method of traverse is to rely entirely on movement along a curved section of track or on a turntable with no provision to traverse the gun on its mount. The second is to traverse the rail car body on its trucks, known as a car-traversing mount. Generally this is limited to a few degrees of traverse to either side unless an elaborate foundation is built with a centre pivot and traversing rollers. The design of the foundation is the only limit to the amount of traverse allowed in this latter case. The third choice is to allow the separate gun mount to rotate with respect to the rail car body, known as a top-carriage traversing mount. This usually requires the gun to be mounted on a central pivot which, in turn, is mounted on the car body. With few exceptions these types of mounts require some number of outriggers, stabilisers, or earth anchors to keep them in place against the recoil forces and are generally more suitable for smaller guns. The American post-World War I assessment of railway artillery considered that the utility of even a small amount of traverse for fine adjustments was high enough that either of the two latter traversing methods is preferable to a fixed mount.[1]

Recoil systems

Cradle recoil (top); top carriage recoil (second); sliding recoil (third); rolling recoil (bottom)

There are four primary methods to absorb the recoil force for railway guns: cradle recoil, top-carriage recoil, sliding recoil and rolling recoil.

Cradle recoil means that the gun recoils backward in its cradle, retarded and stopped by hydraulic buffers. It is returned to battery, or the firing position, by either helical springs or by air in a pneumatic recuperator cylinder that is compressed by the force of recoil. This is the most common method used for lighter railroad guns and for virtually all field artillery designed after the French introduced their Canon de 75 modèle 1897.

Top-carriage recoil is where the gun is mounted in an upper carriage that moves on wheels on fixed rails. The gun and upper carriage recoil together, restrained by the usual hydraulic buffers. Return to battery is effected either by gravity, through the use of inclined rails, which the gun and carriage have run up, by springs, or even by rubber bands, on some improvised mounts.[2] It is not well-suited to firing at high elevations because it cannot absorb much of the vertical component of the recoil force.[3]

This French 320 mm railway gun uses sliding recoil. The jacked-down sleepers are visible at full-size.

Sliding recoil has the car body sitting on a set of wooden crossbeams or "sleepers" placed underneath it which have been jacked down on to a special set of girders incorporated into the track so that about half the weight of the mount has been transferred to them from the trucks. The gun, car body and trucks all recoil together with the friction generated by the crossbeams sliding on the girders absorbing the recoil force after moving only about 1 to 2 metres (3.3 to 6.6 ft) to the rear. The sleepers must be jacked up again to allow the gun to roll forward to its firing position. This was often done by handwheels driving gear trains attached to the wheels, or even by electric motors on more modern mounts. Almost all of these type of mounts were of the non-traversing type and had to be fired from a curved section of track or turntable. The American post-World War I assessment of railway artillery praised its ruggedness, ease of manufacture and convenience in service, but acknowledged its unsuitability for smaller guns, due to excessive time of operation and lack of traverse, and that it was not suitable for the largest howitzers firing at high angles because of the enormous trunnion forces.[3]

With rolling recoil the entire gun, mount and everything rolls backward, typically between 30 to 50 feet (9.1 to 15.2 m), restrained only by the brakes. The mount was winched back into firing position by cables fastened to the track. This system was usually combined with cradle recoil because the springs of the trucks cannot withstand the vertical component of the recoil force alone. This type of mount was usually fitted with car-traverse. It was unsuitable for smaller guns due to the lack of traverse.[3] The great advantage of this method is that it requires minimal preparation and can fire from any suitable section of curved track.[4]

This French 274 mm howitzer used a combination of top-cradle and sliding recoil.

The methods were often used in combination with each other. Examples include the French 520 mm (20 in) railway howitzer which used cradle-sliding recoil. The American's 14"/50 caliber railway gun Mark II used cradle-rolling recoil as did the 14 and 12 inch railway guns from Great Britain. Only the oldest weapons used a combination of top-cradle and sliding recoil. One example being the earliest mounts for the British designed BL 9.2 inch Railway Gun.

Anchorage

No anchorage needed (top); truck platform anchorage (middle); ground platform anchorage (bottom)
French St Chamond 240 mm Canon de Mle 1893/96, WWI, using ground platform anchorage

The combination of rolling and cradle-recoil methods absorbed both the horizontal and vertical components of the recoil force and needed no special preparations, but all other types required some method to transmit the vertical force to the ground. One way is to build a platform on either the ties or the ground with girders, beams, pads or floats. The horizontal component would be alleviated by either sliding recoil or rail clamps, guys or struts to secure the mount in place. The French Schneider 194 mm (7.6 in) and 240 mm (9.4 in) mounts and the British 9.2 inch guns and 12 inch howitzers used rail clamps or guys. The American 8 in (200 mm) gun and the French 240 mm Canon de Mle 1893/96 M used struts.[4]

The other method is build a firing position and recoil pit (épi de tir in French) underneath the tracks, using either heavy timbers like the French 340 mm (13 in) and 400 mm (16 in) howitzers or an elaborate concrete or steel base. These latter were mostly used by the Germans for the 21 cm (8.3 in) and larger railway guns and by the French for their Batignolle mounts. Generally, for these emplacements the rails merely served to guide the gun into position and the gun was often mounted on a central pivot to allow up to 360° of traverse. The primary drawback of these positions was the lengthy time to build them.

History

19th century

The idea of railway guns was first suggested in Russia in 1847 by Gustav Kori (proposal),[5] followed by Ye. Repin (project, 1855), Pyotr Lebedev (who outlined the theoretical foundations of the railway artillery in Primeneniye Zheleznykh Dorog k Zashite Materika, 1857) and P. Fomin (developed a project of a large-calibre cannon, 1860).[6][7]

American Civil War

A 32-pounder Brooke naval rifle railway gun used in the Civil War
The "Dictator", Petersburg (Mathew Brady)

The first railway gun used in combat was a banded 32-pounder Brooke naval rifle mounted on a flat car and shielded by a sloping casemate of railroad iron. On 29 June 1862, Robert E. Lee had the gun pushed by a locomotive over the Richmond and York River line (later part of the Southern Railway) and used at the Battle of Savage's Station to interfere with General George McClellan's plans for siege operations against Richmond during the Union advance up the peninsula.[8] Photographic evidence exists of at least one Union 13-inch siege mortar mounted on a rail car during the Siege of Petersburg. It was nicknamed the Dictator or the Petersburg Express.[9] Another photo exists of a gun mounted on an armoured rail car with the caption of "Railway battery used in siege of Petersburg" although no textual evidence survives in support of the caption, which makes the claim that it is a photo of the Confederate gun from 1862 dubious.

France

France also used improvised railway guns during the Siege of Paris (1870–1871)[10] and the United Kingdom mounted a few 4.7 in (120 mm) guns on railway cars which saw action during the Siege and Relief of Ladysmith during the Second Boer War.[11] A 9.2 inch gun was taken from the Cape Town coast defences and mounted on a rail car to support the British assault on Boer defences at Belfast, north-east of Johannesburg, but the battle ended before it could get into action.[12]

In France, Lt. Col Peigné is often credited with designing the first railway gun in 1883. Commandant Mougin is credited with putting guns on railcars in 1870. The French arms maker Schneider offered a number of models in the late 1880s and produced a 120 mm (4.7 in) gun intended for coastal defence, selling some to the Danish government in the 1890s. They also designed a 200 mm (7.9 in) model for Peru in 1910, but they were never delivered.[13]

World War I

The outbreak of the First World War caught the French with a shortage of heavy field artillery. In compensation, large numbers of large static coastal defence guns and naval guns were moved to the front, but these were typically unsuitable for field use and required some kind of mounting. The railway gun provided the obvious solution. By 1916, both sides were deploying railway guns.

France

Schneider of France developed the Obusier de 520 modèle 1916, a 20-inch (520 mm) railway "Fort Buster" to do what the German 16-inch Big Bertha had done at the outbreak of World War I and reduce the German forts in the final line of German defences. One was destroyed in trials and the other did not complete firing trials prior to the signing of the Armistice. The gun remained in storage and was captured by the Germans during World War II. It later formed part of the German artillery complement during the Siege of Leningrad. The gun was disabled by a premature detonation and later abandoned.

United States

Baldwin Locomotive Works delivered five 14"/50 caliber railway guns on trains for the United States Navy during April and May 1918. Each 14"/50 gun [14] mounted on a 72-foot (22 m), 535,000-pound (243 t) rail carriage with four 6-wheel bogies was under the command of a United States Navy lieutenant with a standard U.S. Army 2-8-0 locomotive, a 10-ton crane car, two armored ammunition cars carrying 25 shells each, two cars carrying the recoil pit foundation materials, two fuel and workshop cars, three berthing cars, a kitchen car, a commissary car, and a medical dispensary car. A sixth locomotive pulled a headquarters car for Rear Admiral Charles Peshall Plunkett, with a machine-shop car, a spare parts car, a berthing car, a kitchen car, a commissary car, and a medical dispensary car.[15] After delivery by ship, these trains were assembled in St. Nazaire in August[16] and fired a total of 782 shells during 25 days on the Western Front at ranges between 27 and 36 kilometres (30,000 and 39,000 yd).[17] Each 14-inch (36 cm) projectile weighed 1,400 pounds (640 kg) and was fired at 2,800 feet (850 m) per second. The railway carriages could elevate the guns to 43 degrees, but elevations over 15 degrees required excavation of a pit with room for the gun to recoil and structural steel shoring foundations to prevent caving of the pit sides from recoil forces absorbed by the surrounding soil.[18] The trains moved cautiously because axle loading under the gun barrels was 50,330 pounds (22.83 t) while French railways were designed for a maximum of 39,000 pounds (18 t). These axle journals overheated at speeds of more than 10 kilometres (6.2 miles) per hour. After reaching its intended firing site and constructing the recoil pit, each gun could fire about two shells per hour. One of these guns was retained after the war as an ammunition test gun at the Dahlgren Weapons Laboratory until all United States battleships with 14"/50 guns were scrapped shortly after World War II.[15] The gun was then placed on display outside the museum at the Washington Navy Yard.

Baldwin constructed six similar gun carriages and two of an improved Mk II type[14] designed to permit firing the gun at all elevation angles without transferring weight to a separate foundation. These eight guns were completed too late to see combat, and were designated the 14-inch M1920 railway guns. Some were later stationed through World War II in special coast defence installations at San Pedro, California (near Los Angeles) and at the Panama Canal Zone where they could be shifted from one ocean to the other in less than a day. Improved carriages were designed to allow transport to several fixed firing emplacements including concrete foundations where the railway trucks were withdrawn so the gun could be rapidly traversed (swiveled horizontally) to engage moving ship targets.[19]

After the American entry into World War I on 6 April 1917, the US Army recognized the need to adopt railway artillery for use on the Western Front. No US railway guns existed at that time. Due to low production and shipping priorities, the Army's railway gun contribution on the Western Front consisted of four Coast Artillery regiments operating French-made weapons. Three additional railway gun regiments were in France, but did not complete training prior to the Armistice and did not see action. Other Coast Artillery units also operated various types of French-, British-, and American-made heavy artillery.[20] The Army also converted some of the numerous US coast artillery weapons to railway mounts. A total of 96 8-inch guns (including some from Navy spares), 129 10-inch guns, 45 12-inch guns, and 150 12-inch mortars could be spared from fixed coast defense batteries or spare stocks. Twelve 7-inch ex-Navy guns and six 12-inch guns being built for Chile were also available. To shorten a long story, none of these weapons were shipped to France except three 8-inch guns, as few of any type were completed before the Armistice. Forty-seven 8-inch railway guns were ordered, with 18 completed by the Armistice and a total of 37 (or 47, references vary) completed before the contract was cancelled. Eight 10-inch railway mounts of 54 ordered were completed by the Armistice, and twelve 12-inch railway mounts were completed by 1 April 1919; the 12-inch contract was cancelled at that point. Three railway mountings for the Chilean 12-inch guns were ready for shipment by the Armistice; the remaining three barrels were retained as spares. A total of twenty-two 10-inch guns were eventually mounted. Ninety-one 12-inch railway mortars were ordered, with 45 complete by 7 April 1919 and the remainder eventually completed.[17][21]

The 7-inch and 8-inch guns and 12-inch mortars used a common carriage, with a depressed center and two 4-wheel or 6-wheel bogies. The bogies were interchangeable for standard-gauge or (with 12-wheel bogies) 60-cm (23.6-inch) gauge track.[22] Outriggers and a rotating mount allowed all-around fire. This allowed the weapons to be used in coast defense against moving targets. The 8-inch guns and 12-inch mortars were retained on railway mountings after the war, while almost all of the 7-inch, 10-inch, and 12-inch guns were returned to the coastal forts. With 47 available, plus an additional 24 ex-Navy Mark VI guns on railway mounts by 1942, the 8-inch guns were the most commonly deployed US railway gun through World War II. Approximately a dozen of these were used for the defense of Oahu, Hawaii. Others were stationed for the coastal defense of Manila (eventually dismounted from the railway carriage at Corregidor), Bermuda, Puget Sound, Chesapeake Bay, Delaware Bay, and Fort Hancock, New Jersey (near New York City).[23][24]

Although numerous 12-inch railway mortars were available, few were deployed. In 1930 the US Army tested them at Fort Hancock, New Jersey and Fort Miles, Delaware.[25] During World War II, four railway mortars were among the temporary harbor defenses of Grays Harbor, Washington, and emplacements for an additional four at Cape George, Washington were constructed but never armed.[26] Of the more than 250 railway guns built in the United States from 1916 to 1942, the five navy 14"/50 guns sent to France during World war I were the only ones to be used in combat.[15]

World War II

Main articles: Schwerer Gustav and Cross-Channel guns in the Second World War

The Second World War saw the final use of the railway gun, with the massive 80 cm (31 in) Schwerer Gustav gun,[27] the largest artillery piece to be used in combat, deployed by Germany. The rise of the aeroplane effectively ended the usefulness of the railway gun. Similar to battleships, they were massive, expensive, and, in the correct conditions, easily destroyed from the air.

Boche Buster, seen from Bourne Park Tunnel on the Elham Valley line, at Bishopsbourne in Kent, 21 March 1941

Both Germany and Great Britain employed railway-mounted guns that were capable of firing across the English Channel between the areas around Dover and Calais.[28] Germany employed a number of 40 cm guns. Britain employed three 13.5-inch (342.9 mm) railway mounted guns on the East Kent Light Railway, located around Lydden and Shepherdswell.[28][29][30] These were known as Gladiator, Sceneshifter and Peacemaker.[28] 9.2 inch Mark 13 guns were located near Canterbury and Hythe, Kent; and 12 inch howitzers, Mk 3 and 5, located around Guston,[28] north of Dover on the Southern Railway line to Deal and Ramsgate.

The 18 inch Howitzer, Boche Buster, featured here, was sited on the Elham Valley Railway, between Bridge, Kent, and Lyminge, and was intended for coastal defence against invasion. It was not capable of cross-channel firing, having a maximum range of only 20 km (12 miles).

Surviving railway guns

A second 283 mm Krupp K5 can be seen at the Todt Battery museum, near Audinghen in northern France.[34]

There is an 8-inch gun on an M1918 Railway Mount, less car, at the University of Tampa, Tampa, FL. See http://andy_bennett.home.mindspring.com/8-inchrailway.html

Images

See also

References

Citations
  1. ^ Miller, p. 39
  2. ^ Miller, p. 52
  3. ^ a b c Miller, p. 65
  4. ^ a b Miller, p. 69
  5. ^ Template:Ru icon http://www.travelzone.lv/lib/zd_puski/index.php
  6. ^ Lebedev, P. N. (2011) [1857]. Применение железных дорог к защите материка. Сочинение инженер-подполковника П. Лебедева (in Russian). Moscow: Kniga po Trebovaniyu. ISBN 978-5-458-11821-7. {{cite book}}: Unknown parameter |trans_title= ignored (|trans-title= suggested) (help)
  7. ^ Denisov, A. P.; Perechnev, Yu. G. (1956). "Глава 4. Береговая артиллерия в Крымской войне 1853–1856 годов". Русская береговая артиллерия. Moscow: Voenizdat. pp. 89–91. {{cite book}}: External link in |chapterurl= (help); Unknown parameter |chapterurl= ignored (|chapter-url= suggested) (help); Unknown parameter |trans_chapter= ignored (|trans-chapter= suggested) (help); Unknown parameter |trans_title= ignored (|trans-title= suggested) (help)
  8. ^ Phillips, p. 225
  9. ^ Miller, pp. 9-16
  10. ^ Tucker, S. C. (2005). The encyclopedia of world war I: A political, social, and military history. Abc-clio. ISBN 1-85109-420-2
  11. ^ Miller, p. 23
  12. ^ Hall
  13. ^ Miller, pp. 17, 23
  14. ^ a b "The United States naval railway batteries in France". Internet Archive.
  15. ^ a b c Schreier, Konrad F., Jr. (1988). "Admiral Plunkett's Railway Battle Fleet". Railroad History. 158 (Spring 1988). The Railway & Locomotive Historical Society: 95–102.{{cite journal}}: CS1 maint: multiple names: authors list (link)
  16. ^ Many, April 1965, p.53
  17. ^ a b Hogg, Ian V. (1998). Allied Artillery of World War I. Ramsbury, Wiltshire, UK: The Crowood Press, Ltd. pp. 138–148. ISBN 1-86126-104-7.
  18. ^ Westing (1966) pp.79-80
  19. ^ Lewis (1979) pp. 103, 106
  20. ^ "Defeating the Hun, The History of the U. S. Army, Coast Artillery Corps During WWI". ancestry.com.
  21. ^ "US Army Railway Artillery, WWI". ancestry.com.
  22. ^ Miller, H. W., LTC, USA Railway Artillery, Vols. I and II, 1921, Vol. I, pp. 131-155
  23. ^ Lewis (1979) pp. 102-110, 140-141
  24. ^ Berhow, pp. 199-228
  25. ^ "Mortar Railway Gun to Aid in Defending Coast" Popular Mechanics, December 1930
  26. ^ Berhow, pp. 216-217
  27. ^ Zaloga (2016), pp. 14-15, 18-19
  28. ^ a b c d Arnold (1982), Pp. 100, 108, 147, 148.
  29. ^ Dale Clarke. "British Artillery 1914–19. Heavy Artillery". Osprey Publishing, London, 2005. Pages 41-42
  30. ^ http://www.doverpages.co.uk/big_guns.htm The Big Guns At Dover WW2 World War Two
  31. ^ "The UK's largest artillery piece, 1 of 12 surviving wartime railway howitzers in the world, is being moved for exhibition in the Netherlands". United Kingdom Government. 27 March 2013. Retrieved 2013-04-08.
  32. ^ Maev Kennedy. "Giant first world war gun on the move across southern England this week". the Guardian.
  33. ^ Doyle, pp. 3
  34. ^ "Musée du Mur de l'Atlantique". Musée du Mur de l'Atlantique.
Bibliography
Wikimedia Commons has media related to Railway guns.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Railway_gun&oldid=747739017"