Optical tweezers
Optical tweezers are the application of a laser beam to provide a mechanical force(pico to femto Newton) needed to physically move very small translucent objects around with nanometer precision. Optical tweezers have been liken to be similar to the science fiction weapon called the tractor beam. Recent development of optical tweezers have made use of supercontinuum that is a non-lasing source.
Besides that, new and innovative optical tweezing methods centering around the key idea of using light to induce the mechanical force have also been introduced in recent year. This means that light acts as a primary source for a secondary process to occurs. This secondary process allows the mechanical manipulation of particles. This is deems as an indirect optical tweezing manner.
For example, by using a photosensitive material actuated by light emitting diode, the photosenstive material is able to induce dielectrophoresis thus moving the microparticles [1]. By forming microbeads made from thermogel hydrogel through a laser source, it is also possible to indirectly manipulate the microparticles [2].
History and Development of Optical Tweezers
In 1986, the use of single beam optical tweezers was first reported in the scientific literature by Arthur Ashkin et al Opt. Lett. 11, 288-290 (1986) from Bell Labs.
In 1997, Steven Chu made use of the optical tweezing techniques and applied to the cooling and trapping of atoms. This led to the the 1997 Nobel Prize in Physics award; one of the recipients, Steven Chu worked with Ashkin at Bell Labs on both atomic cooling and optical tweezers, co-authoring the seminal Optics Letters paper[3][4].
In an interview later [5], Steven Chu mentioned that Askhin whom envisioned and pioneer the optical tweezing method has always wanted to make use of such the optical tweezers to trap atoms. But he did not succeed in his quest which was later fulfil by Steven Chu.
![](http://upload.wikimedia.org/wikipedia/commons/thumb/6/64/StevenChu.jpg/220px-StevenChu.jpg)
Excerpts from the interview
"There was another really wonderful scientist there named Arthur Ashkin, an older department head. I started talking to him casually, in the hallways. He had this dream: "Wouldn't it be nice if you can hold on to an atom with light?" He had tried to pursue this dream in the early seventies, in the mid seventies, but it wasn't really working. They did some very key experiments demonstrating the fundamental forces, but it wasn't looking like they were getting closer to really holding on to atoms with light. Finally the management told Ashkin, "It doesn't look like it's going to work; you've got to move on to other things." But then I came on board, and I was this new, young person who he could corrupt"[6]...Steven Chu
In the 1980s Steven Block, Howard Berg and Herchel Smith first applied the technology to the biological sciences, using it to grasp a bacterium in order to study bacterial flagella.[7] Throughout the 1990s and afterwards, researchers like Carlos Bustamante, James Spudich, and Steven Block pioneered the use of optical trap force spectroscopy to characterize molecular-scale biological motors. These molecular motors are ubiquitous in biology, and are responsible for locomation and mechanical action within the cell. Optical traps allowed these biophysicists to observe the forces and dynamics of nanoscale motors one molecule at a time; optical trap force-spectroscopy has since led to greater understanding of the stochastic nature of these force-generating molecules.
In 2003,The technique of optical tweezers have found new applications in the area of cell sorting. By creating a large optical intensity over the sample area filled with micro-biological sample, the cell can be sorting by its intrinsic optical characteristics, M.P.Macdonald et al [8], Brian A. Koss et al[9].
In the year 2005, a recent breakthrough in cell sorting via optical means is the invention of the opto-electronics tweezers.
In this new process optoelectronics process, a photosensitive surface made of amorphous silicon are optically triggered to conduct electricity (much like electrode) by light-emitting diode. Once a light source is removed, the photosensitive material returns to normal. Depending upon the properties of the particles or cells being studied, they will either be attracted to or repelled by the electric field generated by the optoelectronic tweezer. Although in this technique, there is no optical momentum being directed onto the particles.
However, the use of light to create a micromechanical force is still fulfiling the idea of an optical tweezer. This work is reported in the 2005, July 21 issue of the prestigous journal Nature.[10],[11].
Optical Tweezers in Brief
Since in 1970, A.Ashkinet al Phys. Rev. Lett. 24, 156 has been demonstrated that laser beams can be used to trap and move small particles, e.g. micron-sized latex spheres in water. The optical forces being exerted by optical tweezers on a micron-sized or nano-sized silica/latex spheres around a few pico-newtons even femto-newton that is strong enough to immobolised them. In most instance, the optical tweezers are performed in liquid or air environment. A simplistic understanding of the optical tweezers mechanism can be seen from the image below.
A small sphere interacts with a light field and the particle is drawn to the point of the highest intensity of the beam (gradient Force). Once it reaches the maximum intensity point of the beam it is getting pushed along its propagation direction (scattering Force). This causes the bead to be pushed away, however if the beam is strongly focused the intensity gradient overcomes the push of the beam.
Physics of an Optical Tweezer [13]
The theoretical analysis of optical micromanipulation is based on analysis of how linear momentum of light is transferred to microparticles.
Ashkin proposed two different optical micromanipulation regimes based on the microparticle size (diameter) with respect to the wavelength of the laser used for the optical trap.
In atmospheric science, it is well-known that particle in air scatters light respective to their size. When light scatters in the Rayleigh regime, the scattering particles size is much smaller than the wavelength of the light, thus results in an angular separation of colors that is responsible for the reddish color of sunset and the blue of the sky (selective scattering). When light scatters in the Mie Regime, the particles causing that scattering are larger in size than the wavelengths of light, such as pollen, dust, smoke, water droplets. Mie scattering is responsible for the white appearance of the clouds.
Following that same fashion, Ashkin proposed that optical micromanipulation can be analysis by two separate methods namely, Ray Optics approach for Mie Particles (diameter of particle d > λ wavelength of light) and Electric Dipole approximation for Rayleigh particles (diameter of particle d < λ wavelength of light).
Within the Ray Optics analysis, rays tracing of the refraction and reflection process through the microsphere is sufficient to analyze the optical trapping (seen in the image above).
The simple ray optics equation is developed based on geometrical optics. The ray tracing indicates a directional change of linear momentum with respect to time. Hence, this rate of change of momentum of light rays, by Newton’s 2nd Law of motion (photon as particles), will result in a physical force. Similarly, there will be a reaction force from the sphere acting on the light rays. A crude interpretation would be that a region of higher intensity of light will possess more N photons and thus higher momentum and force due to the change of momentum.
By using a simple ray and force vector diagram, the microsphere will experience two different optical forces due to the Gaussian intensity profile (different of input and output momentum with respect to the sphere). The net forces from the imbalance action and reaction forces pulls the sphere towards the region of highest intensity region of the Gaussian beam. The resultant force is termed as the gradient force. Also there is a strong on-axis scattering forces from the scattering light rays where the sphere is encounters axial force along the beam’s propagation direction.
For a true three-dimensional optical tweezers,the Gaussian beam will be to be focussed using a high numerical aperture(N.A>1.0) microsope objective to achieve the optimum optical gradient force just around the focal point of the microscopic objective.
Using the conservation of momentum, the total force acting onto the sphere will be the summation of all the force acting onto it i.e. the scattering force, gradient force.
On the other hand, in the Rayleigh regime, the particles are not as restricted in particle shapes. In general, the smaller the particle the less the trapping power is required. In most cases, the dipole model and the conservation of momentum model are being used for explaining the working mechanisms of the optical tweezers with respect to the shape of the particles. Hence, the dipole model is used. The electromagnetic radiation of the light will induce dipole to form with the particles. The scattering force comes from the reflected and absorbed light. This vector force has a magnitude proportional to the intensity of light and a direction point toward the propagation of laser light. Furthermore, when light interacts with the particles, polarization occurs. This polarization will cause the particle to experiences a gradient force. This vector force has a magnitude proportional to the gradient intensity and a direction pointing towards the direction of intensity gradient.
Detail process of construction of an optical trapping setup can be found have been listed down by Steven M. Block,[14]
Optical Tweezers based on Alternate Laser Beam modes
Since the first introduction of Optical Tweezers based on a single Gaussian beam (fundamental laser mode TEM00) by A.Ashkin [15] in the 1986.
The concept of a single beam optical tweezers have seen to incoporate a series of high order laser beams i.e Hermite Gaussian beam (TEMxy), Laguerre-Gaussian beams(LG) (TEMpl) and Bessel beams (Jn).[16] have been explored as alternative optical tweezers.
Optical tweezers based on Laguerre Gaussian beam have the unique capability of trapping particles that are optically reflective and absorptive.Laguerre-Gaussian beam also possess a well-definited orbital angular momentum that can rotate the particles [17],[18]. This is accomplished without external mechanical or electrical steering of the beam. Note that by imparting polarization of the light in circular manner using waveplate can allow a Gaussian beam to possible intrinsic spin angular momentum[19].
Besides the use of Laguerre Gaussian beam for optical tweezing, both zeroth and higher Bessel Beams also possess a unique tweezing ability namely, ability to trap and rotate multiple particle millimeter apart and even around obstacles [20][21].
Micromachines can be driven by these unique optical beam due to their intrinsic rotating mechanism due to spin and orbital angular momentum of light. [22]
Optical Tweezers in Manifold
A typical setup has only one or two laser beams. More complex optical tweezing operations that require mulitple laser beams would need extensive modification to the optical tweezing set-up by incoporating laser steering devices such as Acoustic Optical Modulator [23] and Spatial Light modulator [[24]]
One of the main use of the multiple optical traps to configure microparticles into predetermined position and achieve a suitable crystalline structure The three main optical tweezers group that made use of the Spatial Light modulator for optical tweezing are University of New York, Grier's group [25] and University of Glasgow,Padgett's Group[26] and the Riso Group, Jesper's Group[27].
Optical tweezers based on Optical Fibers
The fiber optical trap relies on the same principle as the optical trapping just that the laser is being deliver through Optical fiber. If one end of the optical fiber tip is being moulded into lens-like facet, that lens tip will act as a focusing (converging) point for the high optical gradient trap to be formed. [28].
On the other hand, if the ends of the fiber are not being moulded, the laser exiting the fiber will be diverging and thus a stable optical trap can only be realised through the balanced of the gradient and the scattering force from two opposing ends of the fiber, seen in the figure below.The gradient force will trap the particles the transverse direction, while the axial optical force from the scattering force the two counter propagating beams emerging from the two fibers. The equilibrium z-position of such a trapped bead is where the two scattering forces equal each other out.This work is pioneer by A. Constable et al, Opt. Lett. 18,1867,(1993).And followed by J.Guck et al Phys. Rev. Lett. 84, 5451(2000), whom made use of this technique to stretch microparticles. By manipulating with the input power into the two end of the fiber, there will be an increase of a "optical stretching" that can be used to measure viscoelastic properties of cells, with sensitivity sufficient to distinguish between different individual cytoskeletal phenotypes. i.e. human erythrocytes and mouse fibroblasts. A recent test has seen great success in differentiating of cancerous cells from non-cancerous ones.[29]from the two opposed, non-focused laser beams.
Optical Tweezers in a 'Landscape' (cell sorting)
One of the more common cell sorting systems make use of flow cytometry through fluorescent imaging[30] . In this method, a suspension of biologic cells is sorted into two or more containers, based upon specific fluorescent characteristics of each cell during an assisted flow. By using an electrical charge that the cell is "trapped" in, the cell are then sorted based on the fluorescence intensity measurements. The sorting process is undertaking by an electrostatic deflection system that diverts cell into containers based upon their charge.
In the optically actuated sorting process, the cell are flowed through into an optical landscape
![](http://upload.wikimedia.org/wikipedia/commons/e/e8/Cell.jpg)
i.e 2D or 3D optical lattices. Without any induce electrical charge, the cell would sorting based on their intrinsic refractive index properties and can be re-configurability for dynamic sorting. Mike MacDonald, Gabe Spalding and Kishan Dholakia, Nature 426, 421-424 (2003)[31] made use of diffractive optics and optical elements to create the optical lattice.
On the other hand, K. Ladavac, K. Kasza and D. G. Grier, Physical Review E 70, 010901(R) (2004)[32] made use of the spatial light modulator to project an intensity pattern to enable the optical sorting process.
The main mechanism for sorting is the arrangment of the optical lattice points. As the cell flow through the optical lattice, there are forces due to the particles drag force that is competiting directly with the optical gradient force(See Physics of an Optical Tweezers) from the optical lattice point. By shifting the arrangment of the optical lattice point, there is a preferred optical path where the optical forces are dominate and biased. With the aid of the flow of the cells, there is a resultant forces that is directed along that preferred optical path. Hence, there is a relationship of the flow rate with the optical gradient force. By adjusted the two forces, one will be able to obtain a good optical sorting efficiency.
Competition of the forces in the sorting environoment need fine tuning to succeed in high efficient optical sorting. The need is mainly with regards to the balanced of the forces; drag force due to fluid flow and optical gradient force due to arrangment of intensity spot.
Scientists at the University of St Andrews have developed have receive considerable funding from the UK Engineering and Physical Sciences Research Council (EPSRC) for an optical sorting machine. This new technology could rival the conventional fluorescence- activated cell sorting.[33][34]
Optical tweezers based on Evanescent field
Evanescent field [35] [36] is a residue optical field that "leak" during total internal reflection. This "leaking" of light fades off at an exponential rate. The Evanescent field has found an number of applications area from nanometer resolution imaging (microscopy) and optical micromanipulation (optical tweezers) are becoming ever more relevant in research.
In optical tweezers, a continuous evanescent field can be created when light propagating through a optical waveguide (multiple total internal reflection). The resulting evanescent field have a directional sense and will propel microparticles along its propagating path. This work is first pioneered by S. Kawata and T. Sugiura, in 1992 (Opt. Lett. 17 (11), 772 (1992)). Kawata shown that field can be coupled onto the particles in very close proximity of around 100nanometer.
This direct coupling of the field is treated as a type of photon tunnelling across the gap from prism to microparticles. The result is a directional optical propelling force.
A recent updated version of the Evanescent field optical tweezers made use extended optical landscape patterns to simultaneously guide large number of particles into a preferred direction without using an waveguide. It is termed as Lensless Optical Trapping (“LOT”) [37]. The orderly movement of the particles is aided by the introduction of Ronchi Ruling that create well-defined optical potential wells (replacing the waveguide). This means that particles are propelled by the Evanescent field while being trapped by the linear bright fringes. At the moment, there are scientist working on focussed evanescent field as well [38]
Optical tweezers: an indirect approach
![](http://upload.wikimedia.org/wikipedia/en/thumb/d/d5/Schematic.jpg/220px-Schematic.jpg)
Ming Wu, a University of California Berkeley Professor of electrical engineering and computer sciences invited the new optoelectronic tweezers.
Wu transformed the optical energy from low powered light emitting diodes(LED) into electrical energy via a photoconductive surface. The ideas is to allow the LED to switch on and off the photoconductive material via its fine projection. As the optical pattern can be easily transformable through optical projection, this method allow a high flexibility of switching different optical landscapes.
The manipulation/tweezing process is done by the variations between the electric field actuated by the light pattern. As the particles will be either attracted or repelled from the actuated point due to the its electrical charges. Particles being suspended in a liquid will be susceptible to electrical charge due to the ions in the liquid, this is known as dielectrophoresis.
One clear advantage is that the electrical conductivity between a different cells. Living cells have a lower conductive medium while the dead ones have minimum or no conductive medium. The system is able to manipulating roughly 10,000 cells or particles at the same time.
Measuring the optical forces of optical tweezers (Force spectroscopy)
At present the restoring force is measured on single or dual optical tweezers[39][40]. Recent works have started the measurment of the optical forces in Holographic optical tweezers to enable high quality parallel optical tweezing process [41],[42],[43].
The basic principle behind optical tweezers is the optical momentum transfer associated with refraction of light through the particles thereby bending optical light source. A change in the refraction in both the transverse and axial manner provide a force acting on the object. If the optical beam possess a Gaussian beam profile, the particle should have a strong restoring force that retain the particles at the centre of the beam. This restoring force pulls the particles into the center.
File:Tweezers1 web.jpgFile:Pinzas2 web.jpg
When the particles are displaced from the center of optical trap, the restoring force acts as a optical spring. This means that the optical force can be modelled onto a spring constant model as such that optical force is proportional to the displacement of the particles out of the trap. In actual practice, due to the thermal energy of the surrounding, there is always an inherent Brownian motion (noise). The displacement can be accurately measured by projecting the image of the particles onto a quadrant photodiode. The quandrant photodiode can be used to measure nm-scale displacements[44].
Active Research groups and people in the optical tweezers Community
Research groups
- ATOM3D is a joint research project comprising 7 European optics group with optical tweezing expertise. This project is supported by the EC Sixth Framework Programme (FP6).[45]
- Stanford Optical Tweezing Group, USA[46]
- Bustamante Laboratory at the University of California,Berkeley USA[47]
- Optical tweezing in Cornell University,USA[48]
- The Lang Laboratory at MIT,USA[49]
- Grier Lab at University of New York,USA [50]
- The Meiners Laboratory at The University of Michigan,USA[51]
- Optical Tweezers at Umeå University, Sweden[52]
- Optical trapping Group in University of Queensland, Australia [53]
- Optical trapping Group in University of St Andrews, Scotland,UK [54]
- Optics tweezing in University of Glasgow, Scotland[55]
Researchers
- Steven.M.Block[56] pioneered the use of optical tweezers (gradient force optical traps) and other advanced optical methods, including various kinds of interferometry, to study biological systems[57]
- Carlos Bustamante uses novel methods of single-molecule visualization, such as scanning force microscopy, to study the structure and function of nucleoprotein assemblies [[58]]
- Kishan Dholakia[59] behind the breakthroughs in using optical forces to manipulate cells and other biological structures.[60]
![](http://upload.wikimedia.org/wikipedia/commons/thumb/5/5b/Name.jpg/150px-Name.jpg)
- David Grier prominent among the area of holographic optical trapping technique for manipulating hundreds of objects with a single beam of light,Founder of Array Inc [61],[62]
Annual Meeting on Optical Trapping and Micromanipulation
- Optical Trapping & Optical Micromanipulation Conference(OTOM) III San Diego, CA Aug 13 - Aug 17, 2006
- Optical Trapping & Optical Micromanipulation Conference(OTOM) II (2005)[63]
- Optical Trapping & Optical Micromanipulation Conference(OTOM) I(2004)[64]
The (OTOM I-III) conference Chairs are Kishan Dholakia[65]& Gabriel C. Spalding[66]
Other Resources
Extensive Link Pages to other academic groups in Optical Tweezing
- Extensive links to the worldwide Optical trapping community, hosted at University of St. Andrews, Scotland. [67]
- Jaffar's Group, Anna University, INDIA[68]
Professional Paper reviewing Optical Tweezer
- A. Ashkin, "Optical trapping and manipulation of neutral particles using lasers"[69]
- Neuman, K.C., and Block S.M Review on Optical Trapping method[70]
- M. Lang and S. Block, A Resource Letter on Optical Tweezers[71]
- K.Dholakia on Recent review of state of the art tweezers[72]
- D. McGloin on Review of Bessel beam optical tweezers[73]
- David Grier on A revolution in optical manipulation[74]
- Special Edition of Journal of Modern Optics A selection of optical tweezers papers from some of the leading groups[75]
Web Resources
- Quantum optics which deals with the underlying physics of the optical tweezers
- Tweezers for information on the mechanical device from which optical tweezers take their name
- What are optical tweezers [76]
- Recent Optical Tweezers Journal Papers [77]
Multimedia Links
- BBC Frontier covering the technqiue of Optical Tweezers 2003[78]
- Movies showing positioning and rotation controlled by optical tweezers [79]
- Videos of optical tweezers being used on bacteria.
Commercial optical tweezer systems
There are only a few commercial suppliers of optical tweezers, and they are very expensive systems, the main players are Elliot Scientific [80],Cell Robotics [81], Arryx [82],PALM [83]
References
A more detailed list of references can be obtained from the online manuscript written by Justin E Molloy [84] and Miles J Padgett[85] titled Lights, Action: Optical Tweezers[86]posted online
- ^ A Ashkin, J M Dziedzic, J E Bjorkholm and S Chu, Opt. Lett. 11, 288-290, 1986.
- ^ Hill, Murray (November 1987). "wrote the book on atom trapping". Retrieved June 25, 2005.
Interview conducted for internal newsletter at Bell Labs. Contains confirmation of Askin as the inventor of optical trapping and provides information on the 1997 Nobel Prize in Physics.