Kart racing
Kart racing or karting is a variant of open-wheel motor sport with simple, small four-wheeled vehicles called karts, go-karts, or gearbox/shifter karts depending on the design. They are usually raced on scaled-down circuits. Karting is commonly perceived as the stepping stone to the higher and more expensive ranks of motorsports.
Karts vary widely in speed and some (known as Superkarts) can reach speeds exceeding 160 mph (250 km/h)[1], while go-karts intended for the general public in amusement parks may be limited to speeds of no more than 15 mph (25 km/h). A KF1 kart, with a 125 cc 2-stroke engine and an overall weight including the driver of 150 kilograms has a top speed of 85 mph (140 km/h). It takes a little more than 3 seconds to go from 0 to 60 mph with a 125 cc shifter kart (6 gears), with a top speed of 115 mph (185 km/h) on long circuits.[2]
History
Art Ingels is generally accepted to be the father of karting. A veteran hot rodder and a race car builder at Kurtis Kraft, he built the first kart in Southern California in 1956.[3] Karting has rapidly spread to other countries,[4] and currently has a large following in Europe.
The first kart manufacturer was an American company, Go Kart Manufacturing Co. (1958). McCulloch was the first company, in 1959, to produce engines for karts. Its first engine, the McCulloch MC-10, was an adapted chainsaw 2-stroke engine[5]. Later, in the 1960's, motorcycle engines were also adapted for kart use, before dedicated manufacturers, especially in Italy (IAME), started to build engines for the sport.
Components
Chassis
The chassis are made of steel tube.[6][7] There is no suspension therefore chassis have to be flexible enough to work as a suspension and stiff enough not to break or give way on a turn. Kart chassis are classified in the USA as 'Open', 'Caged', 'Straight' or 'Offset'. All CIK-FIA approved chassis are 'Straight' and 'Open'.
- Open karts have no roll cage.
- Caged karts have a roll cage surrounding the driver; they are mostly used on dirt tracks.
- In Straight chassis the driver sits in the center. Straight chassis are used for sprint racing.
- In Offset chassis the driver sits on the left side. Offset chassis are used for left-turn-only speedway racing.
The stiffness of the chassis enables different handling characteristics for different circumstances. Typically, for dry conditions a stiffer chassis is preferable, while in wet or other poor traction conditions, a more flexible chassis may work better. Best chassis allow for stiffening bars at the rear, front and side to be added or removed according to race conditions.
Braking is achieved by a disc brake mounted on the rear axle. Front disc brakes are increasingly popular; however, certain classes do not allow them.
Professionally raced karts typically weigh 165 to 175 lb (75 to 80 kg), complete without driver. Avanti, Tony Kart, Trulli, Birel, CRG, [Gillard (kart manufacturer)|Gillard]], Intrepid, Kosmic, Zanardi or FA Kart are a few well known examples of the many European manufacturers of race-quality chassis. Margay is an American company producing kart chassis.
Engines
Amusement park go-karts can be powered by 4-stroke engines or electric motors, while racing karts use small 2-stroke or 4-stroke engines.
- Electric go-karts are low maintenance, requiring only that the lead-acid batteries of the cars be plugged into an array of chargers after each run. Since they are pollution-free and emit no smoke, the racetracks can be indoors in controlled environments. A fully charged electric kart can run a maximum of 20 minutes before performance is affected.
- 2-stroke kart engines are developed and built by dedicated manufacturers. Comer, IAME (Parilla, Komet), TM, Vortex, Titan, REFO, Yamaha and Rotax are manufacturers of such engines. These can develop from about 8 hp for a single-cylinder 60 cc unit (MiniROK by Vortex) to 90 hp for a twin 250 cc.[1] Today, the most popular categories worldwide are those using the Touch-and-go (TAG) 125 cc units. The recent 125 cc KF1 engines are electronically limited at 16,000 rpm.[8] Most are water-cooled today; however, previously air-cooled engines dominated the sport.
- 4-stroke engines can be standard air-cooled industrial based engines, sometimes with small modifications, developing from about 5 to 20 hp. Briggs & Stratton, Tecumseh, Kohler, Robin, and Honda are manufacturers of such engines. They are adequate for racing and fun kart applications. There are also more powerful four-stroke engines available from manufacturers like Yamaha, TKM, Biland or Aixro (Wankel engine) offering from 15 hp up to 48 hp. They run to and around 11,000 rpm, and are manufactured specifically for karting. Those are used in some National Championship classes like the two-strokes.
Listen to 2-stroke kart engines - recorded at the 2006 World Championship in Angerville - France
Transmission
Karts do not have a differential.[7][9] The lack of a differential means that one rear tire must slide while cornering; this is achieved by designing the chassis so that the inside rear tire lifts up slightly when the kart turns the corner. This allows the tire to lose some of its grip and slide or lift off the ground completely.
Power is transmitted from the engine to the rear axle by way of a chain. Both engine and axle sprockets are removable; their ratio has to be adapted according to track configuration in order to get the most from the engine.
In the early days, karts were direct drive only, but the inconvenience of that setup soon led to the centrifugal clutch for the club level classes. Dry centrifugal clutches are now used in many categories (Rotax Max is one example) and have become the norm as the top international classes have switched to 125 cc clutched engines as of January 2007.
Tires
Wheels and tires are much smaller than those used on a normal car. Rims are made of magnesium alloy or aluminum. Tires can support cornering forces in excess of 2 G (20 m/s²), depending on chassis, engine, and motor setup.
Similar to other motorsports, kart tires have different types for use appropriate to track conditions:
- Slicks, for dry weather. In international level racing these are some of the softest and most advanced tires in motorsport. Some car tire manufacturers, such as Bridgestone, Dunlop or Maxxis, make tires for karts. There are also specific kart tire manufacturers, which include MG, MOJO, and Vega. Slick kart tires come in many different compounds, from very soft (maximum grip) to very hard (amusement and rental karts, less grip but long life span).
- Rain tires, or "wets", for wet weather. They are grooved, made of soft compound, and are narrower than slicks. Not all racing classes allow rain tires.
- Special, such as spiked tire for icy conditions, or "cuts" for high grip dirt/clay speedways. Cuts are modified slicks using a lathe to optimize handling.
External controls
Go-karts used in amusement parks can be fitted with additional electronic controls such as remote speed limiters to help promote a safer operating environment. In the event of an accident or an out of control racer, the track attendant can remotely slow or stop all vehicles on the track via radio control. This remote speed control can also be used to limit young riders to a slow operating speed, while a race consisting only of adults is permitted a higher speed. These controls can be applied to both electric and combustion-engine karts.
Racing
Kart racing is generally accepted as the most economic form of motorsport available. As a free-time activity, it can be performed by almost anybody, and as a motorsport in itself, it is one of the sports regulated by FIA (under the name of CIK), permitting licensed racing for anyone from the age of 8 onward.
In the USA there is not as much FIA involvement, instead many organizations regulate racing, such as the IKF (International Kart Federation), WKA (World Karting Association), IRA (International Racing Association), KART (Karter's of America Racing Triad), and the more recent Stars of Karting presented by the Indy Racing League.
In the UK the MSA (Motor Sports Association) regulate Karting. Some associations, such as NatSKA (National Schools Karting Association), organize race meetings throughout the country under the authority of the MSA.
In Australia kart racing is administrated by the Australian Karting Association on the behalf of FIA and CAMS.
A variety of kart circuits permit the sport to be practiced, although only homologated tracks can have official races in Europe (see Kart circuits).
Racing classes start at age 7 or 8 (5 in the US with "Kid Karts") and generally run in 3-year age groupings or weight divisions until “senior” status is reached at age 15 or 16, depending on the series.
Racing formats
Typically, race formats are one of the following:
Sprint
Sprint racing takes place on dedicated kart circuits resembling small road courses, with left and right turns. Tracks go from 1/4 mile (400 m) to over 1 mile (1,600 meters) in length.
The sprint format is a series of short-duration races, normally for a small number of laps, that qualify for a final, with a variety of point scoring calculations to determine the event's overall winner. Typical duration does not normally exceed 15 minutes. Here, speed and successful passing is of the most importance. It normally occurs in the format of three qualifying heats and a final race for trophy positions.
The FIA championships, including the Karting World Championship, take place in this format.
Endurance
Endurance races last for an extended period, from 30 minutes up to 24 hours or more, for one or more drivers. In general, consistency, reliability, and pit strategy is of greater importance than all out speed.
Called "Enduro" racing in the USA, most WKA & IKF sanctioned events typically last 30 minutes (Sprint Enduro) or 45 minutes (Laydown Enduro) and are run continuous without pit stops. Enduro events are held on full-size road racing circuits that are usually between 1.5 & 4 miles in length.
As well as the famous 24 Hours of Le Mans race for automobiles there is also a 24 hours event for karts which takes place at the kart circuit Alain Prost at Le Mans, France.[10] This race has taken place since 1986 and its winners list include Sébastien Bourdais (in 1996), four times Champ Car champion and current Formula 1 driver with Toro Rosso.
Speedway
Speedway racing takes place on asphalt or clay oval tracks which are normally between 1/6 mile and 1/4 mile long. Tracks primarily consist of two straights and four left-turn corners, few tracks are symmetric and often the shape parallels that of an egg or a tri-oval.
'Offset' kart chassis have been developed for precise handling and adjustability in left-turn-only racing competition taking place on oval and tri-oval tracks.
Speedway kart races range in length from 4 laps for a trophy dash, to 20 laps for a main event.
The two chief racing formats used in dirt speedway karting are heat races and timed laps qualification :
- The International Kart Federation (IKF) runs a racing format of two 10 lap heats followed by a 20 lap final. Finishing positions in the two heat races are used to calculate the starting position in the feature race.
- The World Karting Association (WKA) uses time qualifying. Karts equipped with transponders are sent out onto the track in groups of 5 or less to try to achieve the fastest lap time. Positions for the 20 laps feature event are determined by qualifying time.
- The American Kart Racing Association (AKRA) uses group transponder qualifying to calculate starting positions for 20-lap features.
Racing categories
There are many different classes or formula in karting.
International
The CIK-FIA sanctions international championships in KF1, KF2, KF3, KZ1, KZ2 and Superkart. These are regarded as the top level classes of karting and are also raced in national championships worldwide. The World Championship (KF1) is decided here. The current 2008 World Champion is Marco Ardigò from Italy.[11]
CIK-FIA categories:
- KF1 (the top level), KF2, KF3, and KF4 (so-called “basic” category). All are using the same water-cooled no-gearbox 125 cc “long life” two-stroke engines with starter and clutch, each with different technical specifications (mufflers, air boxes, carburetor, rev limit etc...).
- KZ1 and KZ2, both 125 cc gearbox categories.
- Superkart, a 250 cc gearbox category.
National
In the UK, the most celebrated karting series is the National karting series, also known as Super 1. There are three types of Super 1 championships:
- MSA series : Formula A, ICA, Junior ICA, Formula 100 and Formula Cadet
- Rotax series : Minimax, Junior Max, Senior Max, Senior Max 177 and Rotax DD2
- TKM series : Formula Junior TKM, Formula Junior Intermediate, Formula TKM Extreme, TKM Junior and Senior 4-stroke and since 2006, Honda Cadet
NatSKA is a budget karting association set up for schools and youth groups in the UK, with 13 classes.
In the United States, the biggest proportion of racers are in the dirt oval classes which often use Briggs & Stratton industrial engines. This style of racing is prominent in the Southeast and Midwest. In the West, European style sprint racing is much more common.
In Australia, classes include Midget, Rookie, Junior and Senior.
Many people race worldwide in Spec series such as Rotax Max (a Touch-and-Go class) or those using the Yamaha KT100 engine.
Karting as a learning tool
Kart racing is usually used as a low-cost and relatively safe way to introduce drivers to motor racing. Many people associate it with young drivers but adults are also very active in karting. Karting is considered the first step in any serious racer's career. It can prepare the driver for high-speed wheel-to-wheel racing by helping develop quick reflexes, precision car control, and decision-making skills. In addition, it brings an awareness of the various parameters that can be altered to try to improve the competitiveness of the kart (examples being tire pressure, gearing, seat position, chassis stiffness) that also exist in other forms of motor racing.
All current as well as many former Formula One racers grew up racing karts, most prominent among them Michael Schumacher, Ayrton Senna, Alain Prost, Fernando Alonso, Kimi Räikkönen and Lewis Hamilton. Many NASCAR drivers also got their start in racing from karts, such as Darrell Waltrip, Lake Speed, Ricky Rudd, Juan Pablo Montoya, Tony Stewart, and Jeff Gordon.
Concession karts
As well as "serious" competitive kart racing, many commercial enterprises offer casual hire of karts known as "Concession" karts. Such karts are usually powered by small, detuned four-stroke engines and are far slower than the fully-fledged competitive versions. These karts are built and set to be drivable by anyone. Some tracks also offer racing capable rental karts, also known as "Arrive and Drive" style karts.
Indoor kart racing
Indoor kart tracks can be found in many large cities in Europe. Most of the time the tracks are located in refurbished factories or warehouses. Tracks are often short and offer a great level of safety. Karts are rented by sessions (10 to 15 minutes usually), they use sturdy chassis completed with dedicated bodywork providing driver safety, they are powered by small 4-stroke engines, in some cases electric motors. Laps are often timed during sessions, lap times can be posted electronically on a board. Races and championships such as The Indoor Karting World Championship (IKWC)[12] are organized and provide a competitive environment for all levels of racers.
There are nearly 80 indoor kart tracks in the United States[13]. Some facilities, such as Pole Position Raceway in Las Vegas for example, use high-performance electric karts.
Notes
- ^ a b Superkart at Magny-Cours - 2007
- ^ What is a Shifter Kart?
- ^ 50 years of karting 1956-2006 - CIK-FIA
- ^ How the kart was first introduced to Europe - by Burton Reinfrank - June 2004
- ^ 1959 - McCulloch's Entry into Kart Racing
- ^ CIK-FIA homologation form - Chassis, 2005
- ^ a b Technical picture of a racing chassis - Margay chassis
- ^ "Article 21 ; Specific Regulations for KF1 ; Engine speed limited to maximum 16,000 rpm." - CIK-FIA 2008 Technical Regulations
- ^ "2.8) TRANSMISSION ; Shall always be to the rear wheels. The method is free but any type of differential, whether through the axle, the wheel mounting hub or by any other means, is prohibited." - CIK-FIA 2008 Technical Regulations
- ^ Template:Fr icon Kart circuit Alain Prost - 24 hours
- ^ 2008 CIK-FIA Karting World Championship - Official Classification
- ^ Indoor Karting World Championship
- ^ Indoor Kart Tracks
See also
Related :
External links
Governing Bodies :
- CIK-FIA web site
- MSA - Motor Sports Association - Governing body for motor sports in Great Britain
- IKF - International Kart Federation - Governing body for the sport of kart racing in the US
- WKA - World Karting Association - Governing body for karting in the US
- AKRA - American Kart Racing Association - Governing body for speedway oval karting in the US
- AKA - Australian Karting Association - Governing body for karting in Australia
- ASN Canada - Governing body for kart racing in Canada
- NatSKA - National Association of Schools and Youth Group Karting - UK
- VKA - Vintage Karting Association - Association for support of karts from karting’s 1956 inception to 1975