100 Gigabit Ethernet
40 Gigabit Ethernet (40GbE) and 100 Gigabit Ethernet (100GbE) are groups of computer networking technologies for transmitting Ethernet frames at rates of 40 and 100 gigabits per second (40 and 100 Gbit/s), respectively. The technology was first defined by the IEEE 802.3ba-2010 standard and later by the 802.3bg-2011, 802.3bj-2014, and 802.3bm-2015 standards.
The standards define numerous port types with different optical and electrical interfaces and different numbers of optical fiber strands per port. Short distances over twinaxial cable are supported. 40GBASE-T uses twisted pair cabling for 40 Gbit/s over distances up to 30 m.
- 1 History
- 2 Standards
- 3 100G interface types
- 4 40G interface types
- 5 Chip-to-chip/chip-to-module interfaces
- 6 Connectors
- 7 100G optical module standards
- 8 Products
- 9 Commercial trials and deployments
- 10 See also
- 11 References
- 12 Further reading
- 13 External links
On July 18, 2006, a call for interest for a High Speed Study Group (HSSG) to investigate new standards for high speed Ethernet was held at the IEEE 802.3 plenary meeting in San Diego.
The first 802.3 HSSG study group meeting was held in September 2006.
On December 5, 2007, the Project Authorization Request (PAR) for the P802.3ba 40 Gbit/s and 100 Gbit/s Ethernet Task Force was approved with the following project scope:
The purpose of this project is to extend the 802.3 protocol to operating speeds of 40 Gb/s and 100 Gb/s in order to provide a significant increase in bandwidth while maintaining maximum compatibility with the installed base of 802.3 interfaces, previous investment in research and development, and principles of network operation and management. The project is to provide for the interconnection of equipment satisfying the distance requirements of the intended applications.
The first 40 Gbit/s Ethernet Single-mode Fibre PMD study group meeting was held in January 2010 and on March 25, 2010 the P802.3bg Single-mode Fibre PMD Task Force was approved for the 40 Gbit/s serial SMF PMD.
The scope of this project is to add a single-mode fiber Physical Medium Dependent (PMD) option for serial 40 Gb/s operation by specifying additions to, and appropriate modifications of, IEEE Std 802.3-2008 as amended by the IEEE P802.3ba project (and any other approved amendment or corrigendum).
In March 2011 the IEEE 802.3bg standard was approved.
On September 10, 2011, the P802.3bj 100 Gbit/s Backplane and Copper Cable task force was approved.
The scope of this project is to specify additions to and appropriate modifications of IEEE Std 802.3 to add 100 Gb/s 4-lane Physical Layer (PHY) specifications and management parameters for operation on backplanes and twinaxial copper cables, and specify optional Energy Efficient Ethernet (EEE) for 40 Gb/s and 100 Gb/s operation over backplanes and copper cables.
On May 10, 2013, the P802.3bm 40 Gbit/s and 100 Gbit/s Fiber Optic Task Force was approved.
This project is to specify additions to and appropriate modifications of IEEE Std 802.3 to add 100 Gb/s Physical Layer (PHY) specifications and management parameters, using a four-lane electrical interface for operation on multimode and single-mode fiber optic cables, and to specify optional Energy Efficient Ethernet (EEE) for 40 Gb/s and 100Gb/s operation over fiber optic cables. In addition, to add 40 Gb/s Physical Layer (PHY) specifications and management parameters for operation on extended reach (>10 km) single-mode fiber optic cables.
Also on May 10, 2013, the P802.3bq 40GBASE-T Task Force was approved.
Specify a Physical Layer (PHY) for operation at 40 Gb/s on balanced twisted-pair copper cabling, using existing Media Access Control, and with extensions to the appropriate physical layer management parameters.
On June 12, 2014, the IEEE 802.3bj standard was approved.
On February 16, 2015, the IEEE 802.3bm standard was approved.
On May 12, 2016, the IEEE P802.3cd Task Force started working to define next generation two-lane 100 Gbit/s PHY.
The IEEE 802.3 working group is concerned with the maintenance and extension of the Ethernet data communications standard. Additions to the 802.3 standard are performed by task forces which are designated by one or two letters. For example, the 802.3z task force drafted the original Gigabit Ethernet standard.
802.3ba is the designation given to the higher speed Ethernet task force which completed its work to modify the 802.3 standard to support speeds higher than 10 Gbit/s in 2010.
The speeds chosen by 802.3ba were 40 and 100 Gbit/s to support both end-point and link aggregation needs. This was the first time two different Ethernet speeds were specified in a single standard. The decision to include both speeds came from pressure to support the 40 Gbit/s rate for local server applications and the 100 Gbit/s rate for internet backbones. The standard was announced in July 2007 and was ratified on June 17, 2010.
The 40/100 Gigabit Ethernet standards encompass a number of different Ethernet physical layer (PHY) specifications. A networking device may support different PHY types by means of pluggable modules. Optical modules are not standardized by any official standards body but are in multi-source agreements (MSAs). One agreement that supports 40 and 100 Gigabit Ethernet is the C Form-factor Pluggable (CFP) MSA which was adopted for distances of 100+ meters. QSFP and CXP connector modules support shorter distances.
- Preserve the 802.3 / Ethernet frame format utilizing the 802.3 MAC
- Preserve minimum and maximum FrameSize of current 802.3 standard
- Support a bit error rate (BER) better than or equal to 10−12 at the MAC/PLS service interface
- Provide appropriate support for OTN
- Support MAC data rates of 40 and 100 Gbit/s
- Provide physical layer specifications (PHY) for operation over single-mode optical fiber (SMF), laser optimized multi-mode optical fiber (MMF) OM3 and OM4, copper cable assembly, and backplane.
|Physical layer||40 Gigabit Ethernet||100 Gigabit Ethernet|
|7 m over twinax copper cable||40GBASE-CR4||100GBASE-CR10
|30 m over "Cat.8" twisted pair||40GBASE-T|
|100 m over OM3 MMF||40GBASE-SR4||100GBASE-SR10
|125 m over OM4 MMF|
|2 km over SMF, serial||40GBASE-FR||100GBASE-CWDM4|
|10 km over SMF||40GBASE-LR4||100GBASE-LR4|
|40 km over SMF||40GBASE-ER4||100GBASE-ER4|
The 100 m laser optimized multi-mode fiber (OM3) objective was met by parallel ribbon cable with 850 nm wavelength 10GBASE-SR like optics (40GBASE-SR4 and 100GBASE-SR10). The backplane objective with 4 lanes of 10GBASE-KR type PHYs (40GBASE-KR4). The copper cable objective is met with 4 or 10 differential lanes using SFF-8642 and SFF-8436 connectors. The 10 and 40 km 100 Gbit/s objectives with four wavelengths (around 1310 nm) of 25 Gbit/s optics (100GBASE-LR4 and 100GBASE-ER4) and the 10 km 40 Gbit/s objective with four wavelengths (around 1310 nm) of 10 Gbit/s optics (40GBASE-LR4).
In January 2010 another IEEE project authorization started a task force to define a 40 Gbit/s serial single-mode optical fiber standard (40GBASE-FR). This was approved as standard 802.3bg in March 2011. It used 1550 nm optics, had a reach of 2 km and was capable of receiving 1550 nm and 1310 nm wavelengths of light. The capability to receive 1310 nm light allows it to inter-operate with a longer reach 1310 nm PHY should one ever be developed. 1550 nm was chosen as the wavelength for 802.3bg transmission to make it compatible with existing test equipment and infrastructure.
In December 2010, a 10x10 multi-source agreement (10x10 MSA) began to define an optical Physical Medium Dependent (PMD) sublayer and establish compatible sources of low-cost, low-power, pluggable optical transceivers based on 10 optical lanes at 10 Gbit/s each. The 10x10 MSA was intended as a lower cost alternative to 100GBASE-LR4 for applications which do not require a link length longer than 2 km. It was intended for use with standard single mode G.652.C/D type low water peak cable with ten wavelengths ranging from 1523 to 1595 nm. The founding members were Google, Brocade Communications, JDSU and Santur. Other member companies of the 10x10 MSA included MRV, Enablence, Cyoptics, AFOP, oplink, Hitachi Cable America, AMS-IX, EXFO, Huawei, Kotura, Facebook and Effdon when the 2 km specification was announced in March 2011. The 10X10 MSA modules were intended to be the same size as the C Form-factor Pluggable specifications.
On June 12, 2014, the 802.3bj standard was approved. The 802.3bj standard specifies 100 Gbit/s 4x25G PHYs - 100GBASE-KR4, 100GBASE-KP4 and 100GBASE-CR4 - for backplane and twin-ax cable.
On February 16, 2015, the 802.3bm standard was approved. The 802.3bm standard specifies a lower-cost optical 100GBASE-SR4 PHY for MMF and a four-lane chip-to-module and chip-to-chip electrical specification (CAUI-4). The detailed objectives for the 802.3bm project can be found on the 802.3 website.
100G interface types
|Lanes||Gigabaud per lane||Notes|
|100GBASE-CR10||85 (802.3ba)||Twin-ax copper cable||10||10.3125||CXP connector, center 10 out of 12 channels|
|100GBASE-CR4||92 (802.3bj)||4||25.78125, RS-FEC|
|100GBASE-SR10||86 (802.3ba)||Multi-mode fiber, 850 nm||10||10.3125||MPO/MTP connector, center 10 out of 12 channels|
|100GBASE-SR4||95 (802.3bm)||4||25.78125, RS-FEC|
|100GBASE-LR4||88 (802.3ba)||Single-mode fiber, WDM:
1295.56 nm, 1300.05 nm,
|1||4||25.78125||10 km reach|
|100GBASE-ER4||30–40 km reach|
|100GBASE-CWDM4 MSA||non-IEEE||Single-mode fiber, WDM:
1271 nm, 1291 nm,
|25.78125, RS-FEC||2 km reach, multi-vendor non-IEEE Standard|
(Open Compute Platform)
|non-IEEE||Single-mode fiber, WDM:
1271 nm, 1291 nm,
|1||4||25.78125, RS-FEC||500m reach, multi-vendor non-IEEE Standard|
|100GBASE-PSM4||non-IEEE||4×Single-mode fiber 1310 nm||4||25.78125||500m, multi-vendor non-IEEE Standard|
|100GBASE-ZR||non-IEEE||Single-mode fiber, 1546.119 nm||1||120.579, DP-QPSK||80+ km reach, non-IEEE Standard|
|100GBASE-KR4||93 (802.3bj)||Copper backplane||4||25.78125, RS-FEC|
|100GBASE-KP4||94 (802.3bj)||additional four level amplitude modulation|
All variants listed in the table share the 64b/66b Physical Coding Sublayer, and the media count is given per direction (i.e. double the count is required to form a link.) RS-FEC refers to the Reed-Solomon Layer defined in Clause 91, introduced in IEEE 802.3bj. DP-QPSK refers to Dual polarization-quadrature phase shift keying.
40G interface types
- 40GBASE-CR4 ("copper") is a port type for twin-ax copper cable. Its 64b/66b PCS is defined in IEEE 802.3 Clause 82 and its PMD in Clause 85. It uses four lanes of twin-axial cable delivering serialized data at a rate of 10.3125 Gbit/s per lane.
- CR4 involves two clauses: CL73 for auto-negotiation, and CL72 for link training. CL73 allows communication between the two PHYs to exchange technical capability pages, and both PHYs come to a common speed and media type. Once CL73 has been completed, CL72 starts. CL72 allows each of the four lanes' transmitters to adjust pre-emphasis via feedback from the link partner.
- 40GBASE-KR4 is a port type for backplanes. Normally backplanes are board traces, such as Megtron6 or FR4 materials. Its Physical Coding Sublayer 64b/66b PCS is defined in IEEE 802.3 Clause 82 and its Physical Medium Dependent PMD in Clause 84. It uses four lanes of backplane delivering serialized data at a rate of 10.3125 Gbit/s per lane.
- As in CR4 case, KR4 involves 2 clauses, first CL73 for autoneg, followed by CL72 for link training. CL73 allows the communication between the 2 PHY's to exchange tech ability pages, and both PHYs come to a common speed and media type. Once CL73 has been completed, CL72 starts. CL72 allows each of the 4 lanes transmitter to adjust its preemphasis by way of feedback from the link partner.
- 40GBASE-SR4 ("short range") is a port type for multi-mode fiber and uses 850 nm lasers. Its Physical Coding Sublayer 64b/66b PCS is defined in IEEE 802.3 Clause 82 and its Physical Medium Dependent PMD in Clause 86. It uses four lanes of multi-mode fiber delivering serialized data at a rate of 10.3125 Gbit/s per lane. 40GBASE-SR4 has a reach of 100 m on OM3 and 150m on OM4. There is a longer range variant 40GBASE-eSR4 with a reach of 300 m on OM3 and 400 m on OM4. This extended reach is equivalent to the reach of 10GBASE-SR.
- 40GBASE-LR4 ("long range") is a port type for single-mode fiber and uses 1300 nm lasers. Its Physical Coding Sublayer 64b/66b PCS is defined in IEEE 802.3 Clause 82 and its Physical Medium Dependent PMD in Clause 87. It uses four wavelengths delivering serialized data at a rate of 10.3125 Gbit/s per wavelength.
- 40GBASE-PLR4 ("parallel long range") is a variant of 40GBASE-LR4 that uses 4 transmitters at 1310nm over 4 single mode fibers (rather than 4 wavelengths over 1 single mode fiber). Unlike LR4, PLR4 allows breakout to 4x 10G.
- 40GBASE-ER4 ("extended range") is a port type for single-mode fiber being defined in P802.3bm and uses 1300 nm lasers. Its Physical Coding Sublayer 64b/66b PCS is defined in IEEE 802.3 Clause 82 and its Physical Medium Dependent PMD in Clause 87. It uses four wavelengths delivering serialized data at a rate of 10.3125 Gbit/s per wavelength.
- 40GBASE-FR is a port type for single-mode fiber. Its Physical Coding Sublayer 64b/66b PCS is defined in IEEE 802.3 Clause 82 and its Physical Medium Dependent PMD in Clause 89. It uses 1550 nm optics, has a reach of 2 km and is capable of receiving 1550 nm and 1310 nm wavelengths of light. The capability to receive 1310 nm light allows it to inter-operate with a longer reach 1310 nm PHY should one ever be developed. 1550 nm was chosen as the wavelength transmission to make it compatible with existing test equipment and infrastructure.
- 40GBASE-T is a port type for 4-pair balanced twisted-pair Cat.8 copper cabling up to 30 m defined in IEEE 802.3bq. IEEE 802.3bq-2016 standard was approved by The IEEE-SA Standards Board on June 30, 2016. It uses 16-level PAM signaling over four lanes at 3,200 MBaud each, scaled up from 10GBASE-T.
- 25GBASE-T is a 25 Gbit/s standard for 4-pair twisted pair that was approved alongside 40GBASE-T. It uses 16-level PAM signaling over four lanes at 2,000 MBaud each, scaled up from 10GBASE-T.
- CAUI-10 is a 100 Gbit/s 10 lane electrical interface defined in 802.3ba.
- CAUI-4 is a 100 Gbit/s 4 lane electrical interface defined in 802.3bm.
- Pluggable Optics Form Factors
- The QSFP+ connector is specified for use with the 40GBASE-CR4/SR4, can be copper direct attached cable (DAC) or optical module, see Figure 85–20 in the 802.3 spec. QSFP modules at 40Gbps can also be used to provide four independent ports of 10 gigabit Ethernet.
- Optical Connectors
- Short reach interfaces use Multiple-Fiber Push-On/Pull-off (MPO) connector, see subclause 184.108.40.206 of the 802.3 spec. 40GBASE-SR4 uses MPO-12 and 100GBASE-SR10 uses MPO-24, with individual optical lanes per fiber strand.
- Long reach interfaces use duplex LC connectors with all optical lanes multiplexed with WDM.
100G optical module standards
- The CFP MSA defines hot-pluggable optical transceiver form factors to enable 40 Gbit/s and 100 Gbit/s applications. CFP modules use the 10-lane CAUI-10 electrical interface.
- CFP2 modules use the 10-lane CAUI-10 electrical interface or the 4-lane CAUI-4 electrical interface.
- QSFP28 modules use the CAUI-4 electrical interface.
- Cisco has the CPAK optical module that uses the four lane CEI-28G-VSR electrical interface.
- There are also CXP and HD module standards. CXP modules use the CAUI-10 electrical interface.
- Copper cables
- Quellan announced a test board in 2009.
- Multimode fiber
- In 2009, Mellanox and Reflex Photonics announced modules based on the CFP agreement.
- Single mode fiber
- Finisar, Sumitomo Electric Industries, and OpNext all demonstrated singlemode 40 or 100 Gbit/s Ethernet modules based on the C Form-factor Pluggable agreement at the European Conference and Exhibition on Optical Communication in 2009.
- Optical fiber IEEE 802.3ba implementations were not compatible with the numerous 40 and 100 Gbit/s line rate transport systems because they had different optical layer and modulation formats as the IEEE 802.3ba Port Types show. In particular, existing 40 Gbit/s transport solutions that used dense wavelength-division multiplexing to pack four 10 Gbit/s signals into one optical medium were not compatible with the IEEE 802.3ba standard, which used either coarse WDM in 1310 nm wavelength region with four 25 Gbit/s or four 10 Gbit/s channels, or parallel optics with four or ten optical fibers per direction.
- Test and measurement
- Ixia developed Physical Coding Sublayer Lanes and demonstrated a working 100GbE link through a test setup at NXTcomm in June 2008. Ixia announced test equipment in November 2008.
- Discovery Semiconductors introduced optoelectronics converters for 100 Gbit/s testing of the 10 km and 40 km Ethernet standards in February 2009.
- JDS Uniphase introduced test and measurement products for 40 and 100 Gbit/s Ethernet in August 2009.
- Spirent Communications introduced test and measurement products in September 2009.
- EXFO demonstrated interoperability in January 2010.
- Xena Networks demonstrated test equipment at the Technical University of Denmark in January 2011.
- Calnex Solutions introduced 100GbE Synchronous Ethernet synchronisation test equipment in November 2014.
- Spirent Communications introduced the Attero-100G for 100GbE and 40GbE impairment emulation in April 2015.
- VeEX introduced its CFP-based UX400-100GE and 40GE test and measurement platform in 2012, followed by CFP2, CFP4, QSFP28 and QSFP+ versions in 2015.
Commercial trials and deployments
Unlike the "race to 10Gbps" that was driven by the imminent need to address growth pains of the Internet in the late 1990s, customer interest in 100 Gbit/s technologies was mostly driven by economic factors. The common reasons to adopt the higher speeds were:
- to reduce the number of optical wavelengths ("lambdas") used and the need to light new fiber
- to utilize bandwidth more efficiently than 10 Gbit/s link aggregate groups
- to provide cheaper wholesale, internet peering and data center connectivity
- to skip the relatively expensive 40 Gbit/s technology and move directly from 10 to 100 Gbit/s
Optical transport systems
Optical signal transmission over a nonlinear medium is principally an analog design problem. As such, it has evolved slower than digital circuit lithography (which generally progressed in step with Moore's law.) This explains why 10 Gbit/s transport systems existed since the mid-1990s, while the first forays into 100 Gbit/s transmission happened about 15 years later – a 10x speed increase over 15 years is far slower than the 2x speed per 1.5 years typically cited for Moore's law.
Nevertheless, at least five firms (Ciena, Alcatel-Lucent, MRV, ADVA Optical and Huawei) made customer announcements for 100 Gbit/s transport systems by August 2011 – with varying degrees of capabilities. Although vendors claimed that 100 Gbit/s light paths could use existing analog optical infrastructure, deployment of high-speed technology was tightly controlled and extensive interoperability tests were required before moving them into service.
Designing routers or switches which support 100 Gbit/s interfaces is difficult. The need to process a 100 Gbit/s stream of packets at line rate without reordering within IP/MPLS microflows is one reason for this.
As of 2011[update], most components in the 100 Gbit/s packet processing path (PHY chips, NPUs, memories) were not readily available off-the-shelf or require extensive qualification and co-design. Another problem is related to the low-output production of 100 Gbit/s optical components, which were also not easily available – especially in pluggable, long-reach or tunable laser flavors.
In November 2007, Alcatel-Lucent held the first field trial of 100 Gbit/s optical transmission. Completed over a live, in-service 504 kilometre portion of the Verizon network, it connected the Florida cities of Tampa and Miami.
100GbE interfaces for the 7450 ESS/7750 SR service routing platform were first announced in June 2009, with field trials with Verizon, T-Systems and Portugal Telecom taking place in June–September 2010. In September 2009, Alcatel-Lucent combined the 100G capabilities of its IP routing and optical transport portfolio in an integrated solution called Converged Backbone Transformation.
In June 2011, Alcatel-Lucent introduced a packet processing architecture known as FP3, advertised for 400 Gbit/s rates. Alcatel-Lucent announced the XRS 7950 core router (based on the FP3) in May 2012.
Mellanox Technologies introduced the ConnectX-4 100GbE single and dual port adapter in November 2014. In the same period, Mellanox introduced availability of 100GbE copper and fiber cables. In June 2015, Mellanox introduced the Spectrum 10, 25, 40, 50 and 100GbE switch models.
Aitia International introduced the C-GEP FPGA-based switching platform in February 2013. Aitia also produce 100G/40G Ethernet PCS/PMA+MAC IP cores for FPGA developers and academic researchers.
Arista Networks introduced the 7500E switch (with up to 96 100GbE ports) in April 2013. In July 2014, Arista introduced the 7280E switch (the world's first top-of-rack switch with 100G uplink ports).
Brocade Communications Systems introduced their first 100GbE products (based on the former Foundry Networks MLXe hardware) in September 2010. In June 2011, the new product went live at the AMS-IX traffic exchange point in Amsterdam.
Cisco Systems and Comcast announced their 100GbE trials in June 2008. However, it is doubtful that this transmission could approach 100 Gbit/s speeds when using a 40 Gbit/s per slot CRS-1 platform for packet processing. Cisco's first deployment of 100GbE at AT&T and Comcast took place in April 2011. In the same year, Cisco tested the 100GbE interface between CRS-3 and a new generation of their ASR9K edge router model.
In October 2008, Huawei presented their first 100GbE interface for their NE5000e router. In September 2009, Huawei also demonstrated an end-to-end 100 Gbit/s link. It was mentioned that Huawei's products had the self-developed NPU "Solar 2.0 PFE2A" onboard and was using pluggable optics in CFP form-factor.
In a mid-2010 product brief, the NE5000e linecards were given the commercial name LPUF-100 and credited with using two Solar-2.0 NPUs per 100GbE port in opposite (ingress/egress) configuration. Nevertheless, in October 2010, the company referenced shipments of NE5000e to Russian cell operator "Megafon" as "40Gbps/slot" solution, with "scalability up to" 100 Gbit/s.
In April 2011, Huawei announced that the NE5000e was updated to carry 2x100GbE interfaces per slot using LPU-200 linecards. In a related solution brief, Huawei reported 120 thousand Solar 1.0 integrated circuits shipped to customers, but no Solar 2.0 numbers were given. Following the August 2011 trial in Russia, Huawei reported paying 100 Gbit/ DWDM customers, but no 100GbE shipments on NE5000e.
Juniper Networks announced 100GbE for its T-series routers in June 2009. The 1x100GbE option followed in Nov 2010, when a joint press release with academic backbone network Internet2 marked the first production 100GbE interfaces going live in real network.
In the same year, Juniper demonstrated 100GbE operation between core (T-series) and edge (MX 3D) routers. Juniper, in March 2011, announced first shipments of 100GbE interfaces to a major North American service provider (Verizon).
In April 2011, Juniper deployed a 100GbE system on the UK education network JANET. In July 2011, Juniper announced 100GbE with Australian ISP iiNet on their T1600 routing platform. Juniper started shipping the MPC3E line card for the MX router, a 100GbE CFP MIC, and a 100GbE LR4 CFP optics in March 2012. In Spring 2013, Juniper Networks announced the availability of the MPC4E line card for the MX router that includes 2 100GbE CFP slots and 8 10GbE SFP+ interfaces.
In June 2015, Juniper Networks announced the availability of its CFP-100GBASE-ZR module which is a plug & play solution that brings 80 km 100GbE to MX & PTX based networks. The CFP-100GBASE-ZR module uses DP-QPSK modulation and coherent receiver technology with an optimized DSP and FEC implementation. The low-power module can be directly retrofitted into existing CFP sockets on MX and PTX routers.
Dell's Force10 switches support 40 Gbit/s interfaces. These 40 Gbit/s fiber-optical interfaces using QSFP+ transceivers can be found on the Z9000 distributed core switches, S4810 and S4820 as well as the blade-switches MXL and the IO-Aggregator. The Dell PowerConnect 8100 series switches also offer 40 Gbit/s QSFP+ interfaces.
Telesoft Technologies Ltd
Telesoft Technologies announced the dual 100G PCIe accelerator card, part of the MPAC-IP series. Telesoft also announced the STR 400G (Segmented Traffic Router) and the 100G MCE (Media Converter and Extension).
- "IEEE P802.3ba 40Gb/s and 100Gb/s Ethernet Task Force". official web site. IEEE. June 19, 2010. Retrieved June 24, 2011.
- "100 Gb/s Backplane and Copper Cable Task Force". official web site. IEEE. Archived from the original on 2013-06-27. Retrieved 2013-06-22.
- "40 Gb/s and 100 Gb/s Fiber Optic Task Force". official web site. IEEE.
- "IEEE Forms Higher Speed Study Group to Explore the Next Generation of Ethernet Technology". 2006-07-25.
- "IEEE 802.3 Higher Speed Study Group". IEEE802.org. Retrieved December 17, 2011.
- Jeff Caruso (June 21, 2007). "Group pushes 100 Gigabit Ethernet: The 'Road to 100G' Alliance is born". Network World. Retrieved June 6, 2011.
- "Project Authorization Request Approval notification: Approcal of P802.3ba" (PDF). IEEE Standards Association Standards Board. December 5, 2007. Retrieved June 6, 2011.
- Caruso, Jeff (2008-01-15). "Standardization work on next Ethernet gets under way". NetworkWorld.
- "IEEE P802.3ba 40Gb/s and 100Gb/s Ethernet Task Force". 2010-06-21.
- "IEEE 802.3ba standard released". Help Net Security web site. June 21, 2010. Retrieved June 24, 2011.
The IEEE 802.3ba standard, ratified June 17, 2010, ...
- "IEEE P802.3bg 40Gb/s Ethernet: Single-mode Fibre PMD Task Force". official task force web site. IEEE 802. April 12, 2011. Retrieved June 7, 2011.
- "P802.3bq PAR" (PDF).
- "[802.3_100GNGOPTX] FW: P802.3bm-2015 Approval Notification". ieee802.org. Retrieved 2015-02-19.
- "IEEE 802.3 50 Gb/s, 100 Gb/s, and 200 Gb/s Ethernet Task Force". May 12, 2016.
- "IEEE 802.3 standard".
- Reimer, Jeremy (2007-07-24). "New Ethernet standard: not 40Gbps, not 100, but both". ars technica.
- "CFP Multi-Source Agreement". official web site. Archived from the original on September 28, 2009. Retrieved June 24, 2011.
- Greg Hankins (October 20, 2009). "IEEE P802.3ba 40 GbE and 100 GbE Standards Update" (PDF). North American Network Operators' Group (NANOG) 47 Presentations. Retrieved June 24, 2011.
- John D'Ambrosia. "IEEE P802.3ba Objectives" (PDF). Archived (PDF) from the original on September 28, 2009. Retrieved September 25, 2009.
- Ilango Ganga (May 13, 2009). "Chief Editor's Report" (PDF). IEEE P802.3ba 40Gb/s and 100Gb/s Ethernet Task Force public record. p. 8. Retrieved June 7, 2011.
- "CWDM4-MSA Group". Retrieved 2015-07-24.
- Ilango Ganga; Brad Booth; Howard Frazier; Shimon Muller; Gary Nicholl (May 13, 2008). "IEEE P802.3ba 40Gb/s and 100Gb/s Ethernet Task Force, May 2008 Meeting".
- Anderson, Jon. "Rationale for dual-band Rx in 40GBASE-FR" (PDF).
- "10 x 10 MSA – Low Cost 100 GB/s Pluggable Optical Transceiver". official web site. 10x10 multi-source agreement. Retrieved June 24, 2011.
- "Leading Industry Peers Join Forces to Develop Low-Cost 100G Multi-Source Agreement". Businesswire news release. December 7, 2010. Retrieved June 24, 2011.
- "10X10 MSA Ratifies Specification for Low Cost 100 Gb/s 2 Kilometer Links" (PDF). News release. 10x10 MSA. March 4, 2011. Retrieved June 24, 2011.
- "CWDM4-MSA Group".
- "100GBase-CWDM4 OCP standards".
- "100G PSM4 MSA".
- Coleman, Doug. "Optical Trends in the Data Center" (PDF).
- Li, Angelina. "Comparison between QSFP-40G-LR4 and QSFP-40G-PLR4". linkedin.com. Retrieved 5 June 2017.
- "IEEE P802.3bq 40GBASE-T Task Force". IEEE 802.3.
- "Approval of IEEE Std 802.3by-2016, IEEE Std 802.3bq-2016, IEEE Std 802.3bp-2016 and IEEE Std 802.3br-2016". IEEE. 2016-06-30..
- "CFP MSA".
- "Cisco CPAK 100GBASE Modules Data Sheet".
- "Multi-Vendor Interoperability Testing of CFP2, CPAK and QSFP28 with CEI-28G-VSR and CEI-25G-LR Interface During ECOC 2013 Exhibition" (PDF).
- Daniel Dove. "4X25G Optical Modules and Future Optics" (PDF). Archived (PDF) from the original on 2013-07-12. Retrieved 2013-07-04.
- "NetLogic Microsystems Announces Industry's First Dual-Mode Quad-Port 10GBASE-KR and 40GBASE-KR4 Backplane PHY with Energy Efficient Ethernet". News release. NetLogic Microsystems. October 13, 2010. Retrieved June 24, 2013.
- "Quellan QLx411GRx 40G Evaluation Board". Archived from the original on September 28, 2009. Retrieved September 25, 2009.
- "Mellanox Technologies". Archived from the original on September 28, 2009. Retrieved September 25, 2009.
- "InterBOARD CFP 100GBASE-SR10 Parallel Optical Module". commercial web site. Reflex Photonics Inc. Archived from the original on September 28, 2009. Retrieved June 7, 2011.
- "Finisar Corporation – Finisar First to Demonstrate 40 Gigabit Ethernet LR4 CFP Transceiver Over 10 km of Optical Fiber at ECOC". Archived from the original on September 28, 2009. Retrieved September 25, 2009.
- "Sumitomo Electric develops 40GbE transceiver". Retrieved September 25, 2009.
- "Hitachi and Opnext unveil receiver for 100GbE and demo 10 km transmission over SMF". Retrieved October 26, 2009.
- "Enabling 100 Gigabit Ethernet Implementing PCS Lanes" (PDF).
- "Avago Technologies, Infinera & Ixia to demo the first 100 Gig Ethernet". Archived from the original on 2012-03-10. Retrieved 7 March 2012.
- "Ixia First to Offer 100 GE Testing Capability". News release. Ixia. September 29, 2008. Retrieved June 7, 2011.
- "40 Gb/s and 100 Gb/s Testing: Overview". commercial web site. Ixia. Retrieved June 7, 2011.
- "Discovery Semiconductors – 100 Gb Ethernet (4 x 25 Gb/s) Quad PIN-TIA Optical Receiver". commercial web site. Retrieved June 7, 2011.
- "JDSU Introduces Industry’s Most Robust 100 Gigabit Ethernet Test Suite". News release. JDS Uniphase. August 19, 2009. Retrieved June 7, 2011.
- "40/100 GbE: Testing the next generation of high speed Ethernet". commercial web site. Spirent Communications. Retrieved June 7, 2011.
- "EXFO and Opnext Achieve Full Interoperability, Successfully Testing IEEE-Compliant 100 Gigabit Ethernet Optics". News release. January 11, 2010. Retrieved June 7, 2011.
- "Workshop on 100 Gigabit Ethernet a huge success". DTU news. Technical University of Denmark. February 2, 2011. Retrieved June 7, 2011.
- Torben R. Simonsen (January 26, 2011). "Dansk virksomhed klar med test til 100 Gb ethernet". Elektronik Branchen. Retrieved June 7, 2011. (Danish)
- "Calnex Solutions Limited | Calnex Solutions Launches Industry-first 100GbE Tester for Synchronisation". RealWire. Retrieved 2015-10-22.
- "Industry’s First 100G Impairment Emulator Helps Reduce the Effect of Latency in High Speed Ethernet Networks". corporate.spirent.com. 15 Apr 2015. Retrieved 2015-10-22.
- "Frost & Sullivan Recognizes VeEX's Technology Development".
- "VeEX introduces industry's smallest multiservice, multitasking analyzer for 40/100G networks. | VeEX Inc. | The Verification EXperts". veexinc.com. Retrieved 2017-02-09.
- "VeEX enhances UX400 Platform with next-gen CFP2 and CFP4 test modules |". advanced-television.com. Retrieved 2017-02-09.
- "VeEX unveils 600G testing for its UX400 platform |". advanced-television.com. Retrieved 2017-02-09.
- 100G in routers Juniper Networks Presentation at ECOC 2009
- "Huawei's 100G is out of the door".
- "Verizon Successfully Completes Industry’s First Field Trial of 100 Gbps Optical Network Transmission".
- "Verizon completes industry-leading 100G Ethernet field trial".
- "A game-changing approach to the core".
- "Alcatel-Lucent's FP3 network processor routes at 400Gbps". Press release. June 29, 2011. Retrieved June 24, 2013.
- David Goldman (May 21, 2012). "How Alcatel-Lucent made the Internet 5 times faster". CNN Money. Retrieved June 24, 2013.
- "100 Gigabit Ethernet (100GE): Services unleashed at speed". Company web site. Archived from the original on November 16, 2012. Retrieved June 24, 2013.
- "Mellanox Enables 100Gb/s Interconnect Solution with Introduction of ConnectX-4 Adapter".
- "Mellanox Announces Availability of 100Gb/s Direct Attach Copper and Active Optical Cables".
- "Mellanox Introduces the World’s First 25/100 Gigabit Open Ethernet-based Switch".
- Pal Varga (May 1, 2013). "Aitia C-GEP development platform?". FPGA Networking. Retrieved June 6, 2015.
- Pal Varga (June 6, 2016). "FPGA IP core for 100G/40G ethernet?". FPGA Networking. Retrieved June 6, 2016.
- Jim Duffy (May 1, 2013). "Arista heading off Cisco/Insieme at 100G SDNs?". Network World. Retrieved May 24, 2013.
- Kristin Bent (July 16, 2014). "Arista Leading 100GbE Charge With 7280E Switch Series Launch". CRN. Retrieved February 18, 2016.
- Brocade set to unveil 100G Ethernet Brocade
- "3 new services are launched by AMS-IX at MORE IP event".
- "Cisco NGN Transport Solutions" (PDF).
- Matsumoto, Craig (April 11, 2011). "AT&T, Comcast Go Live With 100G". Light Reading. Retrieved December 17, 2011.
- Liu, Stephen (July 25, 2011). "Cisco Live! Showing Off 100GbE on CRS-3 and ASR 9000 Series". blogs.cisco.com. Retrieved December 17, 2011.
- Duffy, Jim (November 13, 2012). "Extreme joins Cisco, Brocade, Huawei at 100G". Network World. p. 1. Retrieved January 18, 2013.
- "Huawei Successfully Develops 100 Gigabit Ethernet WDM Prototype".
- "Huawei Launches World' s First End-to-End 100G Solutions".
- "Huawei E2E 100G Solution" (PDF).
- "Russia's MegaFon Awards Backbone Contract to Huawei".
- "Huawei Unveils the World's First 200G High-Speed Line Card for Routers".
- "Huawei 200G Solution".
- "Оборудование Huawei 100G успешно прошло тестирование в России".
- "Juniper networks introduces breakthrough 100 gigabit Ethernet interface for t series routers".
- "Internet2 racing ahead with 100G Ethernet network".
- "Juniper Demonstrates Industry's First Live 100G Traffic From the Network Core to Edge".
- "Verizon First Service Provider to Announce 100G Deployment on U.S. Network".
- Deploying 100GE JANET UK
- "iiNet Pioneers 100GbE with new Juniper Networks Backbone".
- "Juniper networks - Life Begins at 40(km) - 100G ZR Optics".
- Dell Force10 S-series model comparison, visited 2 March 2013
- Technical details PowerConnect 8100 series, visited: 2 March 2013
- "Chelsio Delivers 40Gb Ethernet Adapter (40GbE), Sets new performance bar for high speed Ethernet". Press release. June 11, 2013. Archived from the original on 2013-06-22. Retrieved June 20, 2013.
- Overview of Requirements and Applications for 40 Gigabit Ethernet and 100 Gigabit Ethernet Technology Overview White Paper (Archived 2009-08-01) – Ethernet Alliance
- 40 Gigabit Ethernet and 100 Gigabit Ethernet Technology Overview White Paper – Ethernet Alliance
- Ethernet Alliance
- "100G Ethernet cheat sheet: A collection of articles, slideshows, multimedia content on 100G Ethernet". Network World. November 19, 2009. Retrieved 2016-08-24.
- IEEE P802.3ba 40Gb/s and 100Gb/s Ethernet Task Force
- IEEE P802.3ba 40Gb/s and 100Gb/s Ethernet Task Force public area
- Higher Speed Study Group documents