Jump to content

Republic XP-69

From Wikipedia, the free encyclopedia
(Redirected from XP-69)
XP-69
XP-69 model during wind tunnel testing
General information
TypeFighter
ManufacturerRepublic Aviation
Designer
StatusCanceled
Primary userUnited States Army Air Forces (intended)
Number built1 (incomplete)

The Republic XP-69 was an American fighter aircraft proposed by Republic Aviation in 1941 in response to a requirement by the United States Army Air Corps for a high-speed fighter. Manufacturers were encouraged to consider unorthodox designs; although the design was ordered as a prototype it was canceled because of delays with the engine that was to power it.

Development

[edit]

The United States Army Air Corps began the R40-C fighter competition in February 1940. The competition encouraged manufacturers to propose unorthodox high-speed fighter aircraft that met the requirements of Type Specification XC-622.[1] The specification called for a single-engined high-performance fighter aircraft, with a maximum speed between 425 and 525 mph (684 and 845 km/h), armed with both machine guns and cannons, and be capable of landing on a 3,000 ft (910 m) long grass runway.[2]

Republic was one of six companies selected for the competition, and one of the aircraft proposed to the USAAC by Republic was the AP-12 Rocket. As proposed, the AP-12 was to be powered by a 2,500 hp Wright R-2160-3 Tornado 42-cylinder liquid-cooled radial engine mounted in the mid-section of the aircraft's streamlined, cigar-shaped fuselage, behind the cockpit, which drove a pair of three-bladed contra-rotating propellers.[1][3] It was to be armed with four nose-mounted machine guns firing through the propeller arc, and a single 20 mm cannon firing through the propeller hub.[1] The AP-12 placed 13th out of 26 contestants, forcing Republic to go back to the drawing board to improve its proposal.[1]

In July 1941, Republic submitted an improved design, the AP-18. The AP-18 had little in common with the AP-12. It retained the original aircraft's R-2160 engine, which was now mounted in the nose of a completely new small-cross section airframe.[4] The large radiator was to be mounted under the fuselage. The pressurized cockpit was to feature a bubble canopy, and an armament of four .50 in machine guns and two 37 mm cannons mounted in a laminar flow wing was planned.[4]

XP-69 mockup

In December 1941, the United States Army Air Forces (successor to the USAAC) ordered two prototypes of the AP-18 under the designation XP-69.[1] A mockup was built and was inspected by the USAAF in June 1942.[4][3] Construction of the first prototype began in November of that year.[3] However, due to development troubles and delays with the R-2160 engine, the XP-69 project was canceled in favor of a parallel development, the Republic XP-72, on May 24, 1943. By that time engineering on the project was 75% complete and the prototype was still in the early stages of construction, with the total program cost being $810,000.[3]

Specifications (XP-69 as planned)

[edit]

Data from [4][3]

General characteristics

Performance

  • Maximum speed: 450 mph (720 km/h, 390 kn)
  • Range: 1,800 mi (2,900 km, 1,600 nmi)
  • Service ceiling: 48,900 ft (14,900 m)
  • Rate of climb: 2,750 ft/min (14.0 m/s)

Armament

See also

[edit]

Aircraft of comparable role, configuration, and era

Related lists

References

[edit]
  1. ^ a b c d e Pearce, William (2016-05-07). "Republic XP-69 Fighter". Old Machine Press. Retrieved 2020-06-04.
  2. ^ Chong, Anthony (2016-06-15). Flying Wings & Radical Things: Northrop's Secret Aerospace Projects & Concepts 1939-1994. Specialty Press. p. 13. ISBN 978-1-58007-229-8.
  3. ^ a b c d e Norton, Bill (2008). U.S. Experimental & Prototype Aircraft Projects: Fighters 1939-1945. Specialty Press. p. 155. ISBN 978-1-580-07109-3.
  4. ^ a b c d Baugher, Joe (August 7, 2011). "Republic XP-69". www.joebaugher.com. Retrieved 2020-06-04.
  5. ^ "Airfoils". aerofiles.net. Retrieved 2020-07-11.