|This article needs additional citations for verification. (February 2017) (Learn how and when to remove this template message)|
Albert Dewandre (Liege, Belgium), an engineer and business owner, was the inventor of servo-brake or brake booster system “Dewandre” in 1927. It is a brake boosting system that uses the depression caused by the suction in the intake manifold of an internal combustion engine to reduce the pressure on the brake pedal. The advantage of the Dewandre system is twofold: a softer push on the brake pedal, but also a notably shorter braking distance. His invention was manufactured and sold through the Robert Bosch company.
This article mainly refers to the mechanical device in the context of a brake power booster or vehicular braking-system assist. The term "vacuum servo" is actually a generic term for any device which uses a vacuum to amplify/boost the mechanical effort of a device by use of a vacuum in an assisting chamber, either attached to the input or output, or placed between the input and output. In a Vacuum brake servo, the unit is placed between the brake pedal and the hydraulic master cylinder, using stored vacuum to amplify the drivers pedal efforts, giving a greater braking force.
The term "vacuum Servo" can sometimes be mis-translated in vehicle engineering terms, to "vacuum operated valve" whereby a device is controlled either switched or proportionally by the use of a Vacuum. This device can be readily seen in modern off-road vehicles to engage 4WD and differential locks, and in older vehicles fitted with vacuum controlled servo motor cruise control.
A brake booster is used on virtually all vehicles which use hydraulic brakes for their primary braking circuit. Vacuum servos are not used on vehicles which use cables, rods (or other mechanical linkages), or pressurized air systems for their primary brake circuits.
The vacuum can be generated in two distinct methods, dependent on the type of internal combustion engine, or other motive force (as in electric vehicles). In naturally-aspirated petrol engines, the manifold vacuum is used, whereas in turbo charged, diesel engines, and electric/hybrid vehicles a separate vacuum pump is used (or in certain high altitude places, naturally-aspirated vehicles are not capable of producing enough vacuum for the booster. The vacuum pump can be driven mechanically (from the engine) or by means of an electric motor. The vacuum is transferred to the servo along non-collapsible vacuum lines, and is stored in the servo by using a non-return valve.
The vacuum booster or vacuum servo is used in most modern hydraulic brake systems which contain four wheels. The vacuum booster is attached between the master cylinder and the brake pedal and assists the braking force applied by the driver. These units consist of a hollow housing with a movable rubber diaphragm across the center, creating two chambers. When attached to the intake manifold of the engine or the vacuum pump, the pressure in both chambers of the unit is lowered. The equilibrium created by the low pressure in both chambers keeps the diaphragm from moving until the brake pedal is depressed. A return spring keeps the diaphragm in the starting position until the brake pedal is applied.
When the brake pedal is applied, the movement pushes against a small spring which pushes against an air valve thus opening it to allow atmospheric pressure air to flow into the "supply" chamber of the booster. Once the pedal stops advancing forward, the air valve closes again and can open further to allow more air in for continued boosted braking. Since the pressure becomes higher in one chamber (or "supply" chamber), the diaphragm moves toward the lower pressure chamber (or "vacuum" chamber) with a force created by the area of the diaphragm and the differential pressure. This force, in addition to the driver's foot force, pushes on the master cylinder piston. When the pedal is allowed to return to rest, the air from the supply chamber escapes to the vacuum chamber and can then flow towards the source of vacuum.
A relatively small diameter booster unit is required; for a very conservative 50% manifold vacuum, an assisting force of about 1500 N (150 kgf) is produced by a 20 cm radius diaphragm with an area of 0.03 square meters. The diaphragm will stop moving when the forces on both sides of the chamber reach equilibrium. This can be caused by either the air valve closing (due to the pedal apply stopping) or if "run out" is reached. Run out occurs when the pressure in one chamber reaches atmospheric pressure and no additional force can be generated by the now stagnant differential pressure. After the run out point is reached, only the driver's foot force can be used to further apply the master cylinder piston. In some new models, in addition to providing functionality for ABS, Traction Control, and dynamic stability control, brake hydraulics are being used to augment braking when little or no vacuum is detected in the booster, or booster run-out is reached, or pre-applying the brakes if certain panic braking or wet driving conditions are detected.
A brake booster is an enhanced master cylinder setup used to reduce the amount of pedal pressure needed for braking. It employs a booster set up to act with the master cylinder to give higher hydraulic pressure to the brakes and/or lower force applied on the brake pedal through a brake booster push-rod. The brake booster usually uses vacuum from the engine intake to boost the force applied by the pedal on to the master cylinder, or may employ an extra vacuum pump to enable it. Without the engine running the brake pedal feels very hard and ineffective on the braking capability. An "active" booster is a non "conventional" booster where a solenoid is used to open the booster air valve to automatically push the master cylinder forward to perform some forms of dynamic stability control. Brake boosters come in either a single diaphragm or tandem diaphragm (which is generally used for bigger vehicles and trucks). They can be "cabin-breathers" (taking clean filtered air from inside the cabin thus may be more noisy) or "engine-breathers" (less noisy but more at risk for becoming clogged with mud/ice if not protected properly).
Apart from this additional booster setup, the braking system is a normal hydraulic brake system.
- "Brakes - Hydraulic - EduMech". www.edumech.co.uk. Retrieved 2016-04-25.