Jump to content

Energy modeling

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Praxidicae (talk | contribs) at 18:01, 29 November 2016 (Reverted to revision 752132523 by RobbieIanMorrison (talk). (TW)). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

This article is about modeling energy systems. For the simulation of energy use in buildings, see Building energy simulation.

Energy modeling or energy system modeling is the process of building computer models of energy systems in order to analyze them. Such models often employ scenario analysis to investigate different assumptions about the technical and economic conditions at play. Outputs may include the system feasibility, greenhouse gas emissions, cumulative financial costs, natural resource use, and energy efficiency of the system under investigation. A wide range of techniques are employed, ranging from broadly economic to broadly engineering. Mathematical optimization is often used to determine the least-cost in some sense. Models can be international, regional, national, municipal, or stand-alone in scope. Governments maintain national energy models for energy policy development.

Energy models are usually intended to contribute variously to system operations, engineering design, or energy policy development. This page concentrates on policy models. Individual building energy simulations are explicitly excluded, although they too are sometimes called energy models. IPCC-style integrated models, which also contain a representation of the world energy system and are used to examine global transformation pathways through to 2050 or 2100 are not considered here in detail.

Energy modeling has increased in importance as the need for climate change mitigation has grown in importance. The energy supply sector is the largest contributor to global greenhouse gas emissions.[1] The IPCC reports that climate change mitigation will require a fundamental transformation of the energy supply system, including the substitution of unabated (not captured by CCS) fossil fuel conversion technologies by low-GHG alternatives.[1]

Model types

A wide variety of model types are in use. This section attempts to categorize the key types and their usage. The divisions provided are not hard and fast and mixed-paradigm models exist. In addition, the results from more general models can be used to inform the specification of more detailed models, and vice versa, thereby creating a hierarchy of models. Models may, in general, need to capture "complex dynamics such as:

  • energy system operation
  • technology stock turnover
  • technology innovation
  • firm and household behaviour
  • energy and non-energy capital investment and labour market adjustment dynamics leading to economic restructuring
  • infrastructure deployment and urban planning"[2]: S28–S29  : point form added 

Models may be limited in scope to the electricity sector or they may attempt to cover an energy system in its entirety (see below).

Most energy models are used for scenario analysis. A scenario is a coherent set of assumptions about a possible system. New scenarios are tested against a baseline scenario – normally business-as-usual (BAU) – and the differences in outcome noted.

The time horizon of the model is an important consideration. Single-year models – set in either the present or the future (say 2050) – assume a non-evolving capital structure and focus instead on the operational dynamics of the system. Single-year models normally embed considerable temporal (typically hourly resolution) and technical detail (such as individual generation plant and transmissions lines). Long-range models – cast over one or more decades (from the present until say 2050) – attempt to encapsulate the structural evolution of the system and are used to investigate capacity expansion and energy system transition issues.

Models often use mathematical optimization to solve for redundancy in the specification of the system. Some of the techniques used derive from operations research. Most rely on linear programming (including mixed-integer programming), although some use nonlinear programming. Solvers may use classical or genetic optimisation, such as CMA-ES. Models may be recursive-dynamic, solving sequentially for each time interval, and thus evolving through time. Or they may be framed as a single forward-looking intertemporal problem, and thereby assume perfect foresight. Single-year engineering-based models usually attempt to minimize the short-run financial cost, while single-year market-based models use optimization to determine market clearing. Long-range models, usually spanning decades, attempt to minimize both the short and long-run costs as a single intertemporal problem.

The demand-side (or end-user domain) has historically received relatively scant attention, often modeled by just a simple demand curve. End-user energy demand curves, in the short-run at least, are normally found to be highly inelastic.

As intermittent energy sources and energy demand management grow in importance, models have needed to adopt an hourly temporal resolution in order to better capture their real-time dynamics.[3][4] Long-range models are often limited to calculations at yearly intervals, based on typical day profiles, and are hence less suited to systems with significant variable renewable energy.

Implementing languages include GAMS, MathProg, MATLAB, Mathematica, Python, R, Fortran, Java, C, C++, and Vensim. Occasionally spreadsheets are used.

As noted, IPCC-style integrated models (also known as integrated assessment models or IAM) are not considered here in any detail.[5][6] Integrated models combine simplified sub-models of the world economy, agriculture and land-use, and the global climate system in addition to the world energy system. Examples include GCAM,[7] MESSAGE, and REMIND.[8]

Published surveys on energy system modeling have focused on techniques,[9] general classification,[10] decentralized planning,[11] modeling methods,[12] renewables integration,[13] energy efficiency policies,[14][15] electric vehicle integration,[16] international development,[17] and the use of layered models to support climate protection policy.[18] Deep Decarbonization Pathways Project researchers have also analyzed model typologies.[2]: S30–S31 

Electricity sector models

Electricity sector models are used to model electricity systems. The scope may be national or regional, depending on circumstances. For instance, given the presence of national interconnectors, the western European electricity system may be modeled in its entirety.

Engineering-based models usually contain a good characterization of the technologies involved, including the high-voltage AC transmission grid where appropriate. Some models (for instance, models for Germany) may assume a single common bus or "copper plate" where the grid is strong. The demand-side in electricity sector models is typically represented by a fixed load profile.

Market-based models, in addition, represent the prevailing electricity market, which may include nodal pricing.

Game theory and agent-based models are used to capture and study strategic behavior within electricity markets.[19][20][21]

Energy system models

In addition to the electricity sector, energy system models include the heat, gas, mobility, and other sectors as appropriate.[22] Energy system models are often national in scope, but may be municipal or international.

So-called top-down models are broadly economic in nature and based on either partial equilibrium or general equilibrium. General equilibrium models represent a specialized activity and require dedicated algorithms. Partial equilibrium models are more common.

So-called bottom-up models capture the engineering well and often rely on techniques from operations research. Individual plants are characterized by their efficiency curves (also known as input/output relations), nameplate capacities, investment costs (capex), and operating costs (opex). Some models allow for these parameters to depend on external conditions, such as ambient temperature.[23]

Producing hybrid top-down/bottom-up models to capture both the economics and the engineering has proved challenging.[24]

Established models

This section lists some of the major models in use. These are typically run by national governments.

LEAP

LEAP (Long range Energy Alternatives Planning System) is a software tool for energy policy analysis and climate change mitigation assessment.[25][26] LEAP was developed at the Stockholm Environment Institute's (SEI) US Center. LEAP can be used to examine city, state-wide, national, and regional energy systems. LEAP is normally used for forecast studies of between 20–50 years. Most of its calculations occur at yearly intervals. LEAP allows policy analysts can create and evaluate alternative scenarios and to compare their energy requirements, social costs and benefits, and environmental impacts.

MARKAL/TIMES

Main article: MARKAL

MARKAL (MARKet ALlocation) is an integrated energy systems modeling platform, used to analyze energy, economic, and environmental issues at the global, national, and municipal level over time-frames of up to several decades. MARKAL can be used to quantify the impacts of policy options on technology development and natural resource depletion. The software was developed by the Energy Technology Systems Analysis Programme (ETSAP) of the International Energy Agency (IEA) over a period of almost two decades.

TIMES (The Integrated MARKAL-EFOM System) is an evolution of MARKAL – both energy models have many similarities.[27] TIMES succeeded MARKAL in 2008.[28] Both models are technology explicit, dynamic partial equilibrium models of energy markets. In both cases, the equilibrium is determined by maximizing the total consumer and producer surplus via linear programming. Both MARKAL and TIMES are written in GAMS.

The TIMES model generator was also developed under the Energy Technology Systems Analysis Program (ETSAP). TIMES combines two different, but complementary, systematic approaches to modeling energy – a technical engineering approach and an economic approach. TIMES is a technology rich, bottom-up model generator, which uses linear programming to produce a least-cost energy system, optimized according to a number of user-specified constraints, over the medium to long-term. It is used for "the exploration of possible energy futures based on contrasted scenarios".[29]: 7 

As of 2015, the MARKAL and TIMES model generators are in use in 177 institutions spread over 70 countries.[30]: 5 

NEMS

Main article: National Energy Modeling System

NEMS (National Energy Modeling System) is a long-standing United States government policy model, run be the Department of Energy (DOE). NEMS computes equilibrium fuel prices and quantities for the US energy sector. To do so, the software iteratively solves a sequence of linear programs and nonlinear equations.[31] NEMS has been used to explicitly model the demand-side, in particular to determine consumer technology choices in the residential and commercial building sectors.[32]

NEMS is used to produce the Annual Energy Outlook each year – for instance in 2015.[33]

Criticisms

Public policy energy models have been criticized for being insufficiently transparent. The source code and data sets should at least be available for peer review, if not explicitly published.[34] To improve transparency and public acceptance, some models are undertaken as open-source software projects, often developing a diverse community as they proceed. OSeMOSYS is one such example.[35][36]

See also

General

Models

References

  1. ^ a b Bruckner, Thomas; Bashmakov, Igor Alexeyevic; Mulugetta, Yacob; et al. (2014). "Chapter 7: Energy systems". In IPCC (ed.). Climate change 2014: mitigation of climate change. Contribution of Working Group III to the Fifth Assessment Report of the Intergovernmental Panel on Climate Change (PDF). Cambridge, United Kingdom and New York, NY, USA: Cambridge University Press. pp. 511–597. ISBN 978-1-107-65481-5. Retrieved 9 May 2016.
  2. ^ a b Pye, Steve; Bataille, Chris (2016). "Improving deep decarbonization modelling capacity for developed and developing country contexts". Climate Policy. 16 (S1): S27–S46. doi:10.1080/14693062.2016.1173004.
  3. ^ acatech; Lepoldina; Akademienunion, eds. (2016). Flexibility concepts for the German power supply in 2050 : ensuring stability in the age of renewable energies (PDF). Berlin, Germany: acatech – National Academy of Science and Engineering. ISBN 978-3-8047-3549-1. Retrieved 28 April 2016.
  4. ^ Lunz, Benedikt; Stöcker, Philipp; Eckstein, Sascha; Nebel, Arjuna; Samadi, Sascha; Erlach, Berit; Fischedick, Manfred; Elsner, Peter; Sauer, Dirk Uwe (2016). "Scenario-based comparative assessment of potential future electricity systems – A new methodological approach using Germany in 2050 as an example". Applied Energy. 171: 555–580. doi:10.1016/j.apenergy.2016.03.087.
  5. ^ Clarke, Leon; Jiang, Kejun; et al. (2014). "Chapter 6: Assessing transformation pathways". In IPCC (ed.). Climate change 2014: mitigation of climate change. Contribution of Working Group III to the Fifth Assessment Report of the Intergovernmental Panel on Climate Change (PDF). Cambridge, United Kingdom and New York, NY, USA: Cambridge University Press. ISBN 978-1-107-65481-5. Retrieved 9 May 2016.
  6. ^ Kelly, David L; Kolstad, Charles D (1998). Integrated assessment models for climate change control (PDF). Retrieved 9 May 2016.
  7. ^ Riahi, Keywan; Dentener, Frank; Gielen, Dolf; Grubler, Arnulf; Jewell, Jessica; Klimont, Zbigniew; Krey, Volker; McCollum, David; Pachauri, Shonali; Rao, Shilpa; Ruijven, Bas van; Vuuren, Detlef P van; Wilson, Charlie (2012). "Chapter 17: Energy pathways for sustainable development". In Gomez-Echeverri, L; Johansson, TB; Nakicenovic, N; Patwardhan, A (eds.). Global energy assessment: toward a sustainable future. Laxenburg, Austria, Cambridge, UK, and New York, NY, USA: International Institute for Applied Systems Analysis and Cambridge University Press. pp. 1203–1306. Retrieved 11 May 2016.
  8. ^ Bauer, Nico; Mouratiadou, Ioanna; Luderer, Gunnar; Baumstark, Lavinia; Brecha, Robert J; Edenhofer, Ottmar; Kriegler, Elmar (2016). "Global fossil energy markets and climate change mitigation – an analysis with REMIND" (PDF). Climatic Change. 136 (1): 69–82. doi:10.1007/s10584-013-0901-6. Retrieved 10 May 2016.
  9. ^ Bahn, O; Haurie, A; Zachary, DS (May 2005). "Mathematical modeling and simulation methods in energy systems". Encyclopedia of Life Support Systems (EOLSS) (PDF). Oxford, UK: EOLSS Publishers. ISSN 0711-2440. Retrieved 25 October 2016.
  10. ^ Van Beeck, Nicole MJP (August 1999). Classification of energy models — FEW Research Memorandum — Vol 777 (PDF). Tilburg, Netherlands: Tilburg University, Faculty of Economics and Business Administration. Retrieved 25 October 2016.
  11. ^ Hiremath, RB; Shikha, S; Ravindranath, NH (2007). "Decentralized energy planning: modeling and application — a review". Renewable and Sustainable Energy Reviews. 11 (5): 729–752. doi:10.1016/j.rser.2005.07.005.
  12. ^ Jebaraj, S; Iniyan, S (August 2006). "A review of energy models" (PDF). Renewable and Sustainable Energy Reviews. 10 (4): 281–311. doi:10.1016/j.rser.2004.09.004. Retrieved 2 March 2013.{{cite journal}}: CS1 maint: year (link)
  13. ^ Connolly, David; Lund, Henrik; Mathiesen, Brian Vad; Leahy, Marti (2010). "A review of computer tools for analysing the integration of renewable energy into various energy systems". Applied Energy. 87 (4): 1059–1082. doi:10.1016/j.apenergy.2009.09.026.
  14. ^ Mundaca, Luis; Neij, Lena; Worrell, Ernst; McNeil, Michael A (1 August 2010). Evaluating energy efficiency policies with energy-economy models — Report number LBNL-3862E. Berkeley, CA, US: Ernest Orlando Lawrence Berkeley National Laboratory. doi:10.1146/annurev-environ-052810-164840. OSTI 1001644. Retrieved 4 November 2016.
  15. ^ Mundaca, Luis; Neij, Lena; Worrell, Ernst; McNeil, Michael A (2010). "Evaluating energy efficiency policies with energy-economy models". Annual Review of Environment and Resources. 35 (1): 305–344. doi:10.1146/annurev-environ-052810-164840. ISSN 1543-5938.
  16. ^ Mahmud, Khizir; Town, Graham E (15 June 2016). "A review of computer tools for modeling electric vehicle energy requirements and their impact on power distribution networks". Applied Energy. 172: 337–359. doi:10.1016/j.apenergy.2016.03.100.
  17. ^ van Ruijven, Bas; Urban, Frauke; Benders, René MJ; Moll, Henri C; van der Sluijs, Jeroen P; de Vries, Bert; van Vuuren, Detlef P (December 2008). "Modeling energy and development: an evaluation of models and concepts" (PDF). World Development. 36 (12): 2801–2821. doi:10.1016/j.worlddev.2008.01.011. ISSN 0305-750X. Retrieved 25 October 2016.
  18. ^ Unger, Thomas; Springfeldt, Per Erik; Tennbakk, Berit; Ravn, Hans; Havskjold, Monica; Niemi, Janne; Koljonen, Tiina; Fritz, Peter; Koreneff, Göran; Rydén, Bo; Lehtilä, Antti; Sköldberg, Håkan; Jakobsson, Tobias; Honkatukia, Juha (2010). Coordinated use of energy system models in energy and climate policy analysis: lessons learned from the Nordic Energy Perspectives project (PDF). Stockholm, Sweden: Elforsk. ISBN 978-91-978585-9-5. Retrieved 14 November 2016.
  19. ^ David, AK; Wen, Fushuan (16–20 July 2000). Strategic bidding in competitive electricity markets: a literature survey. Power Engineering Society Summer Meeting – Volume 4. Seattle, WA, USA: IEEE. doi:10.1109/PESS.2000.866982. ISBN 0-7803-6420-1.
  20. ^ Sensfuß, Frank; Ragwitz, Mario; Genoese, Massimo; Möst, Dominik (2007). Agent-based simulation of electricity markets: a literature review — Working paper sustainability and innovation S5/2007 (PDF). Karlsruhe, Germany: Fraunhofer ISI. Retrieved 9 May 2016.
  21. ^ Weidlich, Anke; Veit, Daniel (2008). "A critical survey of agent-based wholesale electricity market models". Energy Economics. 30 (4): 1728–1759. doi:10.1016/j.eneco.2008.01.003.
  22. ^ Abrell, Jan; Weigt, Hannes (2012). "Combining energy networks". Networks and Spatial Economics. Vol. 12, no. 3. pp. 377–401. doi:10.1007/s11067-011-9160-0.
  23. ^ Bruckner, Thomas; Morrison, Robbie; Handley, Chris; Patterson, Murray (2003). "High-resolution modeling of energy-services supply systems using deeco: overview and application to policy development" (PDF). Annals of Operations Research. 121 (1–4): 151–180. doi:10.1023/A:1023359303704. Retrieved 8 May 2016.
  24. ^ Böhringer, Christoph; Rutherford, Thomas F (2008). "Combining bottom-up and top-down". Energy Economics. 30 (2): 574–596. doi:10.1016/j.eneco.2007.03.004.
  25. ^ SEI (May 2012). LEAP : Long range Energy Alternatives Planning System : a tool for energy policy analysis and climate change mitigation assessment – Flyer (PDF). Somerville, MA, USA: Stockholm Environment Institute (SEI) US Center. Retrieved 4 May 2016.
  26. ^ "LEAP : tools for sustainable energy analysis". Retrieved 4 May 2016.
  27. ^ A comparison of the TIMES and MARKAL models (PDF). 2009. Retrieved 31 October 2016.
  28. ^ "MARKAL". Retrieved 31 October 2016.
  29. ^ Loulou, Richard; Remne, Uwe; Kanudia, Amit; Lehtila, Antti; Goldstein, Gary (April 2005). Documentation for the TIMES model – Part I (PDF). Energy Technology Systems Analysis Programme (ETSAP). Retrieved 31 October 2016.
  30. ^ Giannakidis, George; Labriet, Maryse; Gallachóir, Brian Ó; Tosato, GianCarlot, eds. (2015). Informing energy and climate policies using energy systems models: insights from scenario analysis increasing the evidence base. Cham, Switzerland: Springer International Publishing. doi:10.1007/978-3-319-16540-0. ISBN 978-3-319-16540-0.
  31. ^ Gabriel, Steven A; Kydes, Andy S; Whitman, Peter (1999). "The National Energy Modeling System: a large-Scale energy-economic equilibrium model". Operations Research. 49 (1): 14–25. doi:10.1287/opre.49.1.14.11195. Retrieved 9 May 2016.
  32. ^ Wilkerson, Jordan T; Cullenward, Danny; Davidian, Danielle; Weyant, John P (2013). "End use technology choice in the National Energy Modeling System (NEMS): an analysis of the residential and commercial building sectors" (PDF). Energy Economics. 40: 773–784. doi:10.1016/j.eneco.2013.09.023. Retrieved 9 May 2016.
  33. ^ Annual energy outlook 2015 : with projections to 2040 – DOE/EIA-0383(2015) (PDF). Washington, DC, USA: US Energy Information Administration, Office of Integrated and International Energy Analysis, US Department of Energy. April 2015. Retrieved 9 May 2016.
  34. ^ acatech; Lepoldina; Akademienunion, eds. (2016). Consulting with energy scenarios : requirements for scientific policy advice (PDF). Berlin, Germany: acatech – National Academy of Science and Engineering. ISBN 978-3-8047-3550-7. Retrieved 9 November 2016.
  35. ^ Howells, Mark; Rogner, Holger; Strachan, Neil; Heaps, Charles; Huntington, Hillard; Kypreos, Socrates; Hughes, Alison; Silveira, Semida; DeCarolis, Joe; Bazillian, Morgan; Roehrl, Alexander (2011). "OSeMOSYS: the open source energy modeling system: an introduction to its ethos, structure and development". Energy Policy. 39 (10): 5850–5870. doi:10.1016/j.enpol.2011.06.033.
  36. ^ "OSeMOSYS: an open-source energy modelling system". Retrieved 8 May 2016.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Energy_modeling&oldid=752133249"