Jump to content

Epoxide

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Latrissium (talk | contribs) at 16:20, 6 October 2018 (→Uses: Add use of ethylene oxide for sterilisation.). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

A generic epoxide.

An epoxide is a cyclic ether with a three-atom ring. This ring approximates an equilateral triangle, which makes it strained, and hence highly reactive, more so than other ethers. They are produced on a large scale for many applications. In general, low molecular weight epoxides are colourless and nonpolar, and often volatile.[1]

Nomenclature

A compound containing the epoxide functional group can be called an epoxy, epoxide, oxirane, and ethoxyline. Simple epoxides are often referred to as oxides. Thus, the epoxide of ethylene (C2H4) is ethylene oxide (C2H4O). Many compounds have trivial names, ethylene oxide is called "oxirane." Some names emphasize the presence of the epoxide functional group, as in the compound 1,2-epoxyheptane, which can also be called 1,2-heptene oxide.

A polymer formed from epoxide precursors is called an epoxy, but such materials do not contain epoxide groups (or contain only a few residual epoxy groups that remain unreacted in the formation of the resin).

Synthesis

The dominant epoxides industrially are ethylene oxide and propylene oxide, which are produced respectively on the scales of approximately 15 and 3 million tonnes/year.[2]

Heterogeneously catalyzed oxidation of alkenes

The epoxidation of ethylene involves its reaction of oxygen according to the following stoichiometry:

7 H2C=CH2 + 6 O2 → 6 C2H4O + 2 CO2 + 2 H2O

The direct reaction of oxygen with alkenes is useful only for this epoxide. Modified heterogeneous silver catalysts are typically employed.[3] Other alkenes fail to react usefully, even propylene, though TS-1 supported Au catalysts can perform propylene epoxidation selectively.[4]

Olefin oxidation using organic peroxides and metal catalysts

Aside from ethylene oxide, most epoxides are generated by treating alkenes with peroxide-containing reagents, which donate a single oxygen atom. Safety considerations weigh on these reactions because organic peroxides are prone to spontaneous decomposition or even combustion.

Metal complexes are useful catalysts for epoxidations involving hydrogen peroxide and alkyl hydroperoxides. Peroxycarboxylic acids, which are more electrophilic, convert alkenes to epoxides without the intervention of metal catalysts. In specialized applications, other peroxide-containing reagents are employed, such as dimethyldioxirane. Depending on the mechanism of the reaction and the geometry of the alkene starting material, cis and/or trans epoxide diastereomers may be formed. In addition, if there are other stereocenters present in the starting material, they can influence the stereochemistry of the epoxidation. Metal-catalyzed epoxidations were first explored using tert-butyl hydroperoxide (TBHP).[5] Association of TBHP with the metal (M) generates the active metal peroxy complex containing the MOOR group, which then transfers an O center to the alkene.[6]

Simplified mechanism for metal-catalyzed epoxidation of alkenes with peroxide (ROOH) reagents.

Organic peroxides are used for the production of propylene oxide from propylene. Catalysts are required as well. Both t-butyl hydroperoxide and ethylbenzene hydroperoxide can be used as oxygen sources.[7]

Olefin peroxidation using peroxycarboxylic acids

More typically for laboratory operations, the Prilezhaev reaction is employed.[8][9] This approach involves the oxidation of the alkene with a peroxyacid such as m-CPBA. Illustrative is the epoxidation of styrene with perbenzoic acid to styrene oxide:[10]

Prilezhaev Reaction

The reaction proceeds via what is commonly known as the "Butterfly Mechanism."[11] The peroxide is viewed as an electrophile, and the alkene a nucleophile. The reaction is considered to be concerted (the numbers in the mechanism below are for simplification).The butterfly mechanism allows ideal positioning of the O-O sigma star orbital for C-C Pi electrons to attack.[12] Because two bonds are broken and formed to the epoxide oxygen, this is formally an example of a coarctate transition state.

Butterfly Mechanism

Hydroperoxides are also employed in catalytic enantioselective epoxidations, such as the Sharpless epoxidation and the Jacobsen epoxidation. Together with the Shi epoxidation, these reactions are useful for the enantioselective synthesis of chiral epoxides. Oxaziridine reagents may also be used to generate epoxides from alkenes.

Homogeneously catalysed asymmetric epoxidations

Arene oxides are intermediates in the oxidation of arenes by cytochrome P450. For prochiral arenes (naphthalene, toluene, benzoates, benzopyrene), the epoxides are often obtained in high enantioselectivity.

Chiral epoxides can often be derived enantioselectively from prochiral alkenes. Many metal complexes give active catalysts, but the most important involve titanium, vanadium, and molybdenum.[13][14]

The Sharpless epoxidation.

The Sharpless epoxidation reaction is one of the premier enantioselective chemical reactions. It used to prepare 2,3-epoxyalcohols from primary and secondary allylic alcohols.[15][16]

Epichlorohydrin, is prepared by the chlorohydrin method. It is a precursor in the production of epoxy resins.[17]

Intramolecular SN2 substitution

This method involves dehydrohalogenation. It is a variant of the Williamson ether synthesis. In this case, an alkoxide ion intramolecularly displaces chloride. The precursor compounds are called halohydrins.[18] Starting with propylene chlorohydrin, most of the world's supply of propylene oxide arises via this route.[7]

An intramolecular epoxide formation reaction is one of the key steps in the Darzens reaction.

In the Johnson–Corey–Chaykovsky reaction epoxides are generated from carbonyl groups and sulfonium ylides. In this reaction, a sulfonium is the leaving group instead of chloride.

Nucleophilic epoxidation

Electron-deficient olefins, such as enones and acryl derivatives can be epoxidized using nucleophilic oxygen compounds such as peroxides. The reaction is a two-step mechanism. First the oxygen performs a nucleophilic conjugate addition to give a stabilized carbanion. This carbanion then attacks the same oxygen atom, displacing a leaving group from it, to close the epoxide ring.

Biosynthesis

Epoxides are uncommon in nature. They arise usually via oxygenation of alkenes by the action of cytochrome P450.[19] (but see also the short-lived Epoxyeicosatrienoic acids which act as signalling molecules.[20] and similar Epoxydocosapentaenoic acids, and Epoxyeicosatetraenoic acids.)

Reactions

Ring-opening reactions dominate the reactivity of epoxides.

Hydrolysis and addition of nucleophiles

Two pathways for the hydrolysis of an epoxide.

Alcohols, water, amines, thiols and many other reagents add to epoxides. This reaction is the basis of two commercial applications, the formation of epoxy glues and the production of glycols.[17] Under acidic conditions, nucleophilic addition is affected by steric effects, as normally seen for SN2 reactions, as well as the stability of emerging carbocation (as normally seen for SN1 reactions). Hydrolysis of an epoxide in presence of an acid catalyst generates the glycol.

Polymerization and oligomerization

Polymerization of epoxides gives polyethers. For example ethylene oxide polymerizes to give polyethylene glycol, also known as polyethylene oxide. The reaction of an alcohol or a phenol with ethylene oxide, ethoxylation, is widely used to produce surfactants:[21]

ROH + n C2H4O → R(OC2H4)nOH

With anhydrides, epoxides give polyesters.[22]

Other reactions

Uses

Illustrative epoxides

Ethylene oxide is widely used to generate detergents and surfactants by ethoxylation. Its hydrolysis affords ethylene glycol. It is also used for sterilisation of medical instruments and materials.

The reaction of epoxides with amines is the basis for the formation of epoxy glues and structural materials. A typical amine-hardener is triethylenetetramine (TETA).


Safety

Epoxides are alkylating agents, making many of them highly toxic.[26]

See also

References

  1. ^ Guenter Sienel; Robert Rieth; Kenneth T. Rowbottom. "Epoxides". Ullmann's Encyclopedia of Industrial Chemistry. Weinheim: Wiley-VCH. doi:10.1002/14356007.a09_531. ISBN 978-3527306732.
  2. ^ Siegfried Rebsdat, Dieter Mayer "Ethylene Oxide" in Ullmann's Encyclopedia of Industrial Chemistry, Wiley-VCH, Weinheim, 2005.doi:10.1002/14356007.a10_117 Article Online Posting Date: March 15, 2001.
  3. ^ Sajkowski, D. J.; Boudart, M. (1987). "Structure Sensitivity of the Catalytic Oxidation of Ethene by Silver". Catalysis Reviews. 29 (4). Taylor & Francis Online: 325–360. doi:10.1080/01614948708078611.
  4. ^ Nijhuis, T. Alexander; Makkee, Michiel; Moulijn, Jacob A.; Weckhuysen, Bert M. (1 May 2006). "The Production of Propene Oxide: Catalytic Processes and Recent Developments". Industrial & Engineering Chemistry Research. 45 (10). American Chemical Society: 3447–3459. doi:10.1021/ie0513090. Retrieved 30 April 2018.
  5. ^ Indictor, N.; Brill, W. F. J. Org. Chem., 1965, 30 (6), 2074. (doi:10.1021/jo01017a520).
  6. ^ W. R. Thiel "Metal catalyzed oxidations. Part 5. Catalytic olefin epoxidation with seven-coordinate oxobisperoxo molybdenum complexes: a mechanistic study" Journal of Molecular Catalysis A: Chemical 1997, Volume 117, pp. 449–454. doi:10.1016/S1381-1169(96)00291-9
  7. ^ a b Dietmar Kahlich, Uwe Wiechern, Jörg Lindner “Propylene Oxide” in Ullmann's Encyclopedia of Industrial Chemistry, 2002 by Wiley-VCH, Weinheim. doi:10.1002/14356007.a22_239
  8. ^ March, Jerry. 1985. Advanced Organic Chemistry, Reactions, Mechanisms and Structure. 3rd ed. John Wiley & Sons. ISBN 0-471-85472-7.
  9. ^ Nikolaus Prileschajew (1909). "Oxydation ungesättigter Verbindungen mittels organischer Superoxyde". Berichte der deutschen chemischen Gesellschaft. 42 (4): 4811–4815. doi:10.1002/cber.190904204100.
  10. ^ Harold Hibbert and Pauline Burt (1941). "Styrene Oxide". Organic Syntheses; Collected Volumes, vol. 1, p. 494.
  11. ^ Paul D. Bartlett (1950). "Recent work on the mechanisms of peroxide reactions". Record of Chemical Progress. 11: 47–51.
  12. ^ John O. Edwards (1962). Peroxide Reaction Mechanisms. Interscience, New York. pp. 67–106.
  13. ^ D. J. Berrisford, C. Bolm,. K. B. Sharpless "Ligand-Accelerated Catalysis" Angew. Chem. Int. Ed. Engl. 2003, volume 95, pp. 1059–1070. doi:10.1002/anie.199510591
  14. ^ Sheldon, R. A. Journal of Molecular Catalysis, 1980, 1, 107-206. (doi:10.1016/0304-5102(80)85010-3).
  15. ^ Katsuki, T.; Sharpless, K. B. (1980). "The first practical method for asymmetric epoxidation". J. Am. Chem. Soc. 102 (18): 5974. doi:10.1021/ja00538a077.{{cite journal}}: CS1 maint: multiple names: authors list (link)
  16. ^ Hill, J. G.; Sharpless, K. B.; Exon, C. M.; Regenye, R. Org. Synth., Coll. Vol. 7, p. 461 (1990); Vol. 63, p. 66 (1985). (Article Archived 2013-09-27 at the Wayback Machine)
  17. ^ a b Pham, Ha Q.; Marks, Maurice J. "Epoxy Resins". Ullmann's Encyclopedia of Industrial Chemistry. Wiley-VCH. doi:10.1002/14356007.a09_547.pub2.
  18. ^ Koppenhoefer, B.; Schurig, V. (1993). "(R)-Alkyloxiranes of High Enantiomeric Purity from (S)-2-Chloroalkanoic Acids via (S)-2-Chloro-1-Alkanols: (R)-Methyloxirane". Organic Syntheses{{cite journal}}: CS1 maint: multiple names: authors list (link); Collected Volumes, vol. 8, p. 434.
  19. ^ C. J. Thibodeaux, W.-c. Chang, H.-w. Liu "Enzymatic Chemistry of Cyclopropane, Epoxide, and Aziridine Biosynthesis" Chem. Rev., 2012, vol. 112, pp 1681–1709. doi:10.1021/cr200073d
  20. ^ Boron, Walter F. (2003). Medical Physiology: A Cellular And Molecular Approach. Elsevier/Saunders. p. 108. ISBN 1-4160-2328-3. {{cite book}}: Unknown parameter |name-list-format= ignored (|name-list-style= suggested) (help)
  21. ^ Kosswig, Kurt (2002). "Surfactants". Ullmann's Encyclopedia of Industrial Chemistry. Weinheim, GER: Wiley-VCH. doi:10.1002/14356007.a25_747. {{cite encyclopedia}}: Unknown parameter |editors= ignored (|editor= suggested) (help)
  22. ^ "Ring-Opening Copolymerization of Epoxides and Cyclic Anhydrides with Discrete Metal Complexes: Structure–Property Relationships". Chem. Rev. 116: 15167–15197. 2016. doi:10.1021/acs.chemrev.6b00553. {{cite journal}}: Unknown parameter |authors= ignored (help)
  23. ^ Bruce Rickborn and Wallace E. Lamke (1967). "Reduction of epoxides. II. The lithium aluminum hydride and mixed hydride reduction of 3-methylcyclohexene oxide". J. Org. Chem. 32: 537–539. doi:10.1021/jo01278a005.
  24. ^ B. Mudryk; T. Cohen (1995). "1,3-Diols From Lithium Β-lithioalkoxides Generated By The Reductive Lithiation Of Epoxides: 2,5-dimethyl-2,4-hexanediol". Org. Synth. 72: 173. doi:10.15227/orgsyn.072.0173.
  25. ^ K. Barry Sharpless, Martha A. Umbreit, Marjorie T. Nieh, Thomas C. Flood (1972). "Lower valent tungsten halides. New class of reagents for deoxygenation of organic molecules". J. Am. Chem. Soc. 94 (18): 6538–6540. doi:10.1021/ja00773a045.{{cite journal}}: CS1 maint: multiple names: authors list (link)
  26. ^ Niederer, Christian; Behra, Renata; Harder, Angela; Schwarzenbach, René P.; Escher, Beate I. (2004). "Mechanistic approaches for evaluating the toxicity of reactive organochlorines and epoxides in green algae". Environmental Toxicology and Chemistry. 23 (3): 697–704. doi:10.1897/03-83.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Epoxide&oldid=862773464"