Vanadium redox battery
Specific energy | 10–20 Wh/kg (36–72 J/g) |
---|---|
Energy density | 15–25 Wh/L (54–65 kJ/L) |
Charge/discharge efficiency | 75–80%<.[1][2] |
Time durability | 20-30 years |
Cycle durability | >100,000 cycles [citation needed] |
Nominal cell voltage | 1.15–1.55 V |
![](http://upload.wikimedia.org/wikipedia/commons/thumb/5/5b/Redox_Flow_Battery.jpg/220px-Redox_Flow_Battery.jpg)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/f/fd/1_MW_4_MWh_Turner_Energy_Storage_Project_in_Pullman%2C_WA.jpg/220px-1_MW_4_MWh_Turner_Energy_Storage_Project_in_Pullman%2C_WA.jpg)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/2/28/Vanadium_Redox_flow_battery.jpg/220px-Vanadium_Redox_flow_battery.jpg)
The vanadium redox battery (VRB), also known as the vanadium flow battery (VFB) or vanadium redox flow battery (VRFB), is a type of rechargeable flow battery that employs vanadium ions in different oxidation states to store chemical potential energy.[4] The vanadium redox battery exploits the ability of vanadium to exist in solution in four different oxidation states, and uses this property to make a battery that has just one electroactive element instead of two.[5] For several reasons, including their relative bulkiness, most vanadium batteries are currently used for grid energy storage, i.e., attached to power plants or electrical grids.
The possibility of creating a vanadium flow battery was explored variously by Pissoort in the 1930s,[6] NASA researchers in the 1970s, and Pellegri and Spaziante in the 1970s,[7] but none of them were successful in demonstrating the technology. The first successful demonstration of the all-vanadium redox flow battery which employed vanadium in a solution of sulfuric acid in each half was by Maria Skyllas-Kazacos at the University of New South Wales in the 1980s.[8] Her design used sulfuric acid electrolytes, and was patented by the University of New South Wales in Australia in 1986.[2]
The main advantages of the vanadium redox battery are that it can offer almost unlimited energy capacity simply by using larger electrolyte storage tanks; it can be left completely discharged for long periods with no ill effects; if the electrolytes are accidentally mixed, the battery suffers no permanent damage; a single state of charge between the two electrolytes avoids the capacity degradation due to a single cell in non-flow batteries; the electrolyte is aqueous and inherently safe and non-flammable,[9]; and the generation 3 formulation using a mixed acid solution developed by the Pacific Northwest National Laboratory operates over a wider temperature range[10] allowing for passive cooling [11]
The main disadvantages with vanadium redox technology are a relatively poor energy-to-volume ratio in comparison with standard storage batteries (although the Generation 3 formulation has doubled the energy density [11] of the system), and the aqueous electrolyte makes the battery heavy and therefore only useful for stationary applications.
Numerous companies and organizations involved in funding and developing vanadium redox batteries include Vionx (formerly Premium Power), UniEnergy Technologies[12] and Ashlawn Energy[13] in the United States; Renewable Energy Dynamics Technology[14] in Ireland; Gildemeister AG (formerly Cellstrom GmbH in Austria, energy division now defunct) in Germany;[15] Cellennium in Thailand Rongke Power;[16] Prudent Energy in China;[17] Sumitomo in Japan; H2, Inc. in South Korea;[18] redT in Britain.,[19] Australian Vanadium in Australia,[20] and the now defunct Imergy (formerly Deeya).[21] Lately, also several smaller size vanadium redox flow batteries were brought to market (for residential applications) mainly from StorEn Technologies (USA), Schmid Group,[22] VoltStorage [23] and Volterion [24] (all three from Germany), VisBlue [25] (Denmark) or Pinflow energy storage [26] (Czechia).
Operation
![](http://upload.wikimedia.org/wikipedia/commons/thumb/a/ae/Vanadium_battery.svg/220px-Vanadium_battery.svg.png)
A vanadium redox battery consists of an assembly of power cells in which the two electrolytes are separated by a proton exchange membrane. The electrodes in a VRB cell are carbon based; the most common types being carbon felt, carbon paper, carbon cloth, and graphite felt. Recently, carbon nanotube based electrodes have gained marked interest from the scientific community.[27][28][29] Both electrolytes are vanadium-based, the electrolyte in the positive half-cells contains VO2+ and VO2+ ions, the electrolyte in the negative half-cells, V3+ and V2+ ions. The electrolytes may be prepared by any of several processes, including electrolytically dissolving vanadium pentoxide (V2O5) in sulfuric acid (H2SO4). The solution remains strongly acidic in use.
In vanadium flow batteries, both half-cells are additionally connected to storage tanks and pumps so that very large volumes of the electrolytes can be circulated through the cell. This circulation of liquid electrolytes is somewhat cumbersome and does restrict the use of vanadium flow batteries in mobile applications, effectively confining them to large fixed installations.
When the vanadium battery is being charged, the VO2+ ions in the positive half-cell are converted to VO2+ ions when electrons are removed from the positive terminal of the battery. Similarly in the negative half-cell, electrons are introduced converting the V3+ ions into V2+. During discharge this process is reversed and results in a typical open-circuit voltage of 1.41 V at 25 °C.
Other useful properties of vanadium flow batteries are their very fast response to changing loads and their extremely large overload capacities. Studies by the University of New South Wales have shown that they can achieve a response time of under half a millisecond for a 100% load change, and allowed overloads of as much as 400% for 10 seconds. The response time is mostly limited by the electrical equipment. Sulfuric acid-based vanadium batteries only work between about 10 and 40 °C. Below that temperature range, the ion-infused sulfuric acid crystallizes.[30] Round trip efficiency in practical applications is around 65–75 %.[31]
Proposed improvements
Second generation[32] vanadium redox batteries (vanadium/bromine) may approximately double the energy density and increase the temperature range in which the battery can operate.
Despite the traditional pumping requirements, nanoFlowcell AG has developed a proprietary system of energy storage for electric vehicle applications showcased through a number of Quant vehicle prototypes, using rapid replacement of electrolyte to refuel the battery.[33]
Specific energy and energy density
Current production vanadium redox batteries achieve a specific energy of about 20 Wh/kg (72 kJ/kg) of electrolyte. More recent research at UNSW indicates that the use of precipitation inhibitors can increase the density to about 35 Wh/kg (126 kJ/kg), with even higher densities made possible by controlling the electrolyte temperature. This specific energy is quite low compared to other rechargeable battery types (e.g., lead–acid, 30–40 Wh/kg (108–144 kJ/kg); and lithium ion, 80–200 Wh/kg (288–720 kJ/kg)).
Mechanisms of Electrode Permeation by Electrolyte
A number or research groups worldwide have reported capacity loss in VRFBs over prolonged periods of use. While several causes have been considered, the influence of electrode microstructure on cell electrochemistry within the electrode is poorly known. Electrolytic wetting of carbon electrodes in VRFBs is important for overcoming sources of degradation and applying appropriate operational procedures. Recently, it appears that electrolytic wetting behaviour within the electrode may be influenced by local concentration effects as well as capillary action.[34] Rapid wetting or permeation may also leave behind undissolved gases which could cause electrode degradation.
Applications
The extremely large capacities possible from vanadium redox batteries make them well suited to use in large power storage applications such as helping to average out the production of highly variable generation sources such as wind or solar power, helping generators cope with large surges in demand or leveling out supply/demand at a transmission constrained region.
The limited self-discharge characteristics of vanadium redox batteries make them useful in applications where the batteries must be stored for long periods of time with little maintenance while maintaining a ready state. This has led to their adoption in some military electronics, such as the sensor components of the GATOR mine system. Their ability to fully cycle and stay at 0% state of charge makes them suitable for solar + storage applications where the battery must start each day empty and fill up depending upon the load and weather. Lithium Ion batteries, for example, are typically damaged when they are allowed to discharge below 20% state of charge, so they typically only operate between about 20% and 100%, meaning they are only using 80% of their nameplate capacity.[35]
Their extremely rapid response times also make them superbly well suited to UPS type applications, where they can be used to replace lead–acid batteries and even diesel generators. Also the fast response time makes them well-suited for frequency regulation. Economically neither the UPS or frequency regulation applications of the battery are currently sustainable alone, but rather the battery is able to layer these applications with other uses to capitalize on various sources of revenue. Also, these capabilities make Vanadium redox batteries an effective "all-in-one" solution for microgrids that depend on reliable operations, frequency regulation and have a need for load shifting (from either high renewable penetration, a highly variable load or desire to optimize generator efficiency through time-shifting dispatch).
Largest vanadium grid batteries
Name | Commissioning date | Energy (MWh) | Power (MW) | Duration (hours) | Country |
---|---|---|---|---|---|
Minami Hayakita Substation[36][37] | December 2015 | 60 | 15 | 4 | Japan |
Woniushi, Liaoning[38][39] | 10 | 5 | 2 | China | |
Tomamae Wind Farm[40] | 2005 | 6 | 4 | 1:30 | Japan |
Zhangbei Project[41] | 2016 | 8 | 2 | 4 | China |
SnoPUD MESA 2 Project [42][43] | March 2017 | 8 | 2 | 4 | USA |
San Miguel Substation[44] | 2017 | 8 | 2 | 4 | USA |
Pullman Washington[45] | April 2015 | 4 | 1 | 4 | USA |
A 200 MW, 800 MWh (4 hours) vanadium redox battery is under construction in China; it is expected to be completed by 2018.[46]
See also
![](http://upload.wikimedia.org/wikipedia/en/thumb/4/4a/Commons-logo.svg/30px-Commons-logo.svg.png)
References
- ^ Vanadium Battery Group University of New South Wales
- ^ a b M. Skyllas-Kazacos, M. Rychcik and R. Robins, in AU Patent 575247 (1986), to Unisearch Ltd.
- ^ Qi, Zhaoxiang; Koenig, Gary M. (July 2017). "Review Article: Flow battery systems with solid electroactive materials". Journal of Vacuum Science & Technology B, Nanotechnology and Microelectronics: Materials, Processing, Measurement, and Phenomena. 35 (4): 040801. doi:10.1116/1.4983210. ISSN 2166-2746.
- ^ Laurence Knight (14 June 2014). "Vanadium: The metal that may soon be powering your neighbourhood". BBC. Retrieved 2 March 2015.
- ^ Alotto, P.; Guarnieri, M.; Moro, F. (2014). "Redox Flow Batteries for the storage of renewable energy: a review". Renewable & Sustainable Energy Reviews. 29: 325–335. doi:10.1016/j.rser.2013.08.001.
{{cite journal}}
: Invalid|ref=harv
(help) - ^ P. A. Pissoort, in FR Patent 754065 (1933)
- ^ A. Pelligri and P. M. Spaziante, in GB Patent 2030349 (1978), to Oronzio de Nori Impianti Elettrochimici S.p.A.
- ^ M. Rychcik and M. Skyllas-Kazacos, J. Power Sources, 22 (1988) 59–67
- ^ UniEnergy Technologies Products[dead link] Accessed 21 Jan 2016.
- ^ "Vanadium Redox Flow Batteries" (PDF). Pacific Northwest National Laboratory. October 2012.
- ^ a b Miller, Kelsey. UniEnergy Technologies Goes from Molecules to Megawatts Archived 31 January 2016 at the Wayback Machine, Clean Tech Alliance, 7 July 2014. Accessed 21 Jan 2016.
- ^ Steve Wilhelm (3 July 2014). "Liquid battery the size of a truck, will give utilities a charge". Puget Sound Business Journal. Retrieved 2 May 2015.
- ^ BILL HAGSTRAND (23 August 2013). "Vanadium redox: powering up local communities". Crain's Cleveland Business. Retrieved 2 May 2015.
- ^ "US clean-tech investments leap to US$1.1bn. Where's Ireland at?". Silicon Republic. 11 April 2011. Retrieved 2 May 2015.
- ^ "a+f acquires majority stake in Cellstrom". DMG Mori Seiki AG. 16 April 2010. Archived from the original on 24 August 2014. Retrieved 21 June 2014.
{{cite web}}
: Unknown parameter|deadurl=
ignored (|url-status=
suggested) (help) - ^ 系统发生错误
- ^ Jeff St. John (2 March 2010). "Made in China: Prudent Energy Lands $22M For Flow Batteries". GigaOm. Retrieved 2 May 2015.
- ^ (주)에이치투
- ^ redT energy storage - Maximise Your Energy
- ^ "Australian Vanadium Ltd ships first vanadium flow battery from Austria". Proactive Investors. 13 July 2016. Retrieved 24 November 2017.
- ^ Eric Wessoff (29 July 2016). "Australian Vanadium Ltd ships first vanadium flow battery from AustriaFlow Battery Aspirant Imergy Has Let Go Its Staff and Is Selling Its Assets". Greentech Media. Retrieved 18 December 2017.
- ^ "Schmid Everflow".
- ^ "Voltstorage develops a safe and ecological storage solution".
- ^ "Unsere Stacks machen Redox-Flow-Batterien wettbewerbsfähig".
- ^ "New technology for storing green energy".
- ^ "Power in Flow".
- ^ Mustafa, Ibrahim; Lopez, Ivan; Younes, Hammad; Susantyoko, Rahmat Agung; Al-Rub, Rashid Abu; Almheiri, Saif (2017-03). "Fabrication of Freestanding Sheets of Multiwalled Carbon Nanotubes (Buckypapers) for Vanadium Redox Flow Batteries and Effects of Fabrication Variables on Electrochemical Performance". Electrochimica Acta. 230: 222–235. doi:10.1016/j.electacta.2017.01.186. ISSN 0013-4686.
{{cite journal}}
: Check date values in:|date=
(help) - ^ Mustafa, Ibrahim; Bamgbopa, Musbaudeen O.; Alraeesi, Eman; Shao-Horn, Yang; Sun, Hong; Almheiri, Saif (1 January 2017). "Insights on the Electrochemical Activity of Porous Carbonaceous Electrodes in Non-Aqueous Vanadium Redox Flow Batteries". Journal of The Electrochemical Society. 164 (14): A3673–A3683. doi:10.1149/2.0621714jes. ISSN 0013-4651.
- ^ Mustafa, Ibrahim; Al Shehhi, Asma; Al Hammadi, Ayoob; Susantyoko, Rahmat; Palmisano, Giovanni; Almheiri, Saif (2018-05). "Effects of carbonaceous impurities on the electrochemical activity of multiwalled carbon nanotube electrodes for vanadium redox flow batteries". Carbon. 131: 47–59. doi:10.1016/j.carbon.2018.01.069. ISSN 0008-6223.
{{cite journal}}
: Check date values in:|date=
(help) - ^ DOE/Pacific Northwest National Laboratory (17 March 2011). "Electric Grid Reliability: Increasing Energy Storage in Vanadium Redox Batteries by 70 Percent". Science Daily. Retrieved 2 March 2015.
- ^ VRB Power Systems FAQ Archived 13 February 2010 at the Wayback Machine
- ^ History of Vanadium Redox Battery
- ^ "Electric Vehicle Refuelling System (EVRS) used in conjunction with Vanadium Redox Flow Technology". REDT Energy Storage. Archived from the original on 6 December 2013.
{{cite web}}
: Unknown parameter|deadurl=
ignored (|url-status=
suggested) (help) - ^ Tariq, Farid; Rubio-Garcia, J.; Yufit, Vladimir; Bertei, Antonio; Chakrabarti, Barun K.; Kucernak, Anthony; Brandon, Nigel (2018). "Uncovering the mechanisms of electrolyte permeation in porous electrodes for redox flow batteries through real time in situ 3D imaging". Sustainable Energy & Fuels. 2 (9): 2068–2080. doi:10.1039/C8SE00174J. ISSN 2398-4902.
- ^ Allbright, Greg, et. al. A Comparison of Lead Acid to Lithium-ion in Stationary Storage Applications All Cell, March 2012
- ^ Stone, Mike (3 February 2016). "A Look at the Biggest Energy Storage Projects Built Around the World in the Last Year". Retrieved 12 August 2017.
- ^ "DOE Global Energy Storage Database". www.energystorageexchange.org. Retrieved 9 November 2017.
- ^ "Energy Storage in China". www.ees-magazine.com. Retrieved 12 August 2017.
- ^ http://energystorage-journal.com:81/EN/10.3969/j.issn.2095-4239.2014.01.010
- ^ "DOE Global Energy Storage Database". www.energystorageexchange.org. Retrieved 9 November 2017.
- ^ "DOE Global Energy Storage Database". www.energystorageexchange.org. Retrieved 9 November 2017.
- ^ "UET and Snohomish County PUD Dedicate the World's Largest Capacity Containerized Flow Battery". Energy Storage News. 29 March 2017. Retrieved 29 December 2017.
- ^ "PUD invests $11.2 million in energy-storing units". Everett Herald. 2 November 2016. Retrieved 29 December 2017.
- ^ "SDG&E and Sumitomo unveil largest vanadium redox flow battery in the US". Energy Storage News. 17 March 2017. Retrieved 12 August 2017.
- ^ Wesoff, Eric, St. John, Jeff. Largest Capacity Flow Battery in North America and EU is Online, Greentech Media, June 2015. Accessed 21 Jan 2016.
- ^ "It's Big and Long-Lived, and It Won't Catch Fire: The Vanadium Redox-Flow Battery". IEEE Spectrum: Technology, Engineering, and Science News. Retrieved 12 November 2017.
Additional references
- Presentation paper from the IEEE summer 2001 conference
- UNSW Site on Vanadium batteries
- Report by World Energy
- World Map Of Global Vanadium Deposits Vanadium geology is fairly unusual compared to a base metals ore body.
- "Improved Redox Flow Batteries For Electric Cars". ScienceDaily/Fraunhofer-Gesellschaft. 13 October 2009. Retrieved 21 June 2014.
External links
- VRB at UNSW
- VRB at everything2
- The Need for Vanadium Redox Energy Storage in Wind Turbine Generators Net electricity generation from all forms of renewable energies in America increased by over 15% between 2005 and 2009.