Barbed wire: Difference between revisions
m →In the American West: WP:CHECKWIKI error fix. Syntax fixes. Do general fixes if a problem exists. - using AWB (11876) |
Cyberbot II (talk | contribs) Rescuing 1 sources. #IABot |
||
Line 177: | Line 177: | ||
Grazing animals with slow movements that will back off at the first notion of pain (''e.g.'', sheep and cows) will not generally suffer the severe injuries often seen in other animals. |
Grazing animals with slow movements that will back off at the first notion of pain (''e.g.'', sheep and cows) will not generally suffer the severe injuries often seen in other animals. |
||
⚫ | Barbed wire has been reported as a tool for human [[torture]].<ref>{{cite web|last=Ferriman |first=Annabel |title=Human rights group uncovers evidence of torture in Zimbabwe |publisher=BMJ Publishing Group Ltd |date=2002-02-09 |url=http://www.bmj.com/cgi/content/full/324/7333/317 |accessdate=2007-08-28 |deadurl=yes |archiveurl=http://web.archive.org/web/20080212162858/http://www.bmj.com:80/cgi/content/full/324/7333/317 |archivedate=February 12, 2008 }}</ref> It is also frequently used as a weapon in [[hardcore wrestling|hardcore professional wrestling]] matches, often as a covering for another type of weapon—[[Mick Foley]] was infamous for using a baseball bat wrapped in barbed wire—and infrequently as a covering of or substitute for the ring ropes. |
||
Barbed wire has been reported as a tool for human [[torture]].<ref>{{cite web |
|||
| last = Ferriman |
|||
| first = Annabel |
|||
| title = Human rights group uncovers evidence of torture in Zimbabwe |
|||
| publisher = BMJ Publishing Group Ltd |
|||
| date = 2002-02-09 |
|||
| url = http://www.bmj.com/cgi/content/full/324/7333/317 |
|||
| accessdate = 2007-08-28 |
|||
⚫ | |||
==Installation of barbed wire== |
==Installation of barbed wire== |
Revision as of 16:27, 27 February 2016
![](http://upload.wikimedia.org/wikipedia/commons/thumb/5/55/Barbed_Wire_Roll.jpg/220px-Barbed_Wire_Roll.jpg)
Barbed wire, also known as barb wire, less often bob wire[1][2] or, in the southeastern United States, bobbed wire,[3] is a type of steel fencing wire constructed with sharp edges or points arranged at intervals along the strand(s). It is used to construct inexpensive fences and is used atop walls surrounding secured property. It is also a major feature of the fortifications in trench warfare (as a wire obstacle).
A person or animal trying to pass through or over barbed wire will suffer discomfort and possibly injury. Barbed wire fencing requires only fence posts, wire, and fixing devices such as staples. It is simple to construct and quick to erect, even by an unskilled person.
The first patent in the United States for barbed wire was issued in 1867 to Lucien B. Smith of Kent, Ohio, who is regarded as the inventor.[4][5] Joseph F. Glidden of DeKalb, Illinois, received a patent for the modern invention in 1874 after he made his own modifications to previous versions.
Barbed wire was the first wire technology capable of restraining cattle. Wire fences were cheaper and easier to erect than their alternatives. (One such alternative was Osage orange, a thorny bush which was time-consuming to transplant and grow. The Osage orange later became a supplier of the wood used in making barb wire fence posts.[6]) When wire fences became widely available in the United States in the late 19th century, they made it affordable to fence much larger areas than before. They made intensive animal husbandry practical on a much larger scale.
An example of the costs of fencing with lumber immediately prior to the invention of barbed wire can be found with the first farmers in the Fresno, California area, who spent nearly $4000 (over $75,000 in present-day dollars) to have wood for fencing delivered and erected to protect 2500 acres of wheat crop from free-ranging livestock in 1872.[7]
History
Before 1865
Englishman Richard Newton brought barbed wire to the Argentine pampas in 1845.[8]
Fencing consisting of flat and thin wire was first proposed in France, by Leonce Eugene Grassin-Baledans in 1860. His design consisted of bristling points, creating a fence that was painful to cross. In April 1865 Louis François Janin proposed a double wire with diamond-shaped metal barbs; he was granted a patent. Michael Kelly from New York had a similar idea, and proposed that the fencing should be used specifically for deterring animals.[9]
More patents followed, and in 1867 alone there were six patents issued for barbed wire. Only two of them addressed livestock deterrence, one of which was from American Lucien B. Smith of Ohio.[10] Before 1870, westward movement in the USA was largely across the plains with little or no settlement occurring. After the American Civil War the plains were extensively settled, consolidating America's dominance over them.[11]
Ranchers moved out on the plains, and needed to fence their land in against encroaching farmers and other ranchers. The railroads throughout the growing West needed to keep livestock off their tracks, and farmers needed to keep stray cattle from trampling their crops.[12] Traditional fence materials used in the Eastern U.S., like wood and stone, were expensive to use in the large open spaces of the plains, and hedging was not reliable in the rocky, clay-based and rain-starved dusty soils. A cost-effective alternative was needed to make cattle operations profitable.[13]
The 1873 meeting and initial development
![](http://upload.wikimedia.org/wikipedia/commons/thumb/0/08/Glidden_wire_the_Winner2.jpg/220px-Glidden_wire_the_Winner2.jpg)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/d/d0/Patent_Drawing_for_Joseph_F._Glidden%27s_Improvement_to_Barbed_Wire_-_NARA_-_302051.tif/lossy-page1-220px-Patent_Drawing_for_Joseph_F._Glidden%27s_Improvement_to_Barbed_Wire_-_NARA_-_302051.tif.jpg)
The "Big Four" in barbed wire were Joseph Glidden, Jacob Haish, Charles Francis Washburn, and Isaac L. Ellwood.[14] Glidden, a farmer in 1873 and the first of the "Big Four," is often credited for designing a successful sturdy barbed wire product, but he let others popularize it for him. Glidden's idea came from a display at a fair in DeKalb, Illinois in 1873, by Henry B. Rose. Rose had patented "The Wooden Strip with Metallic Points" in May 1873.[15]
This was simply a wooden block with wire protrusions designed to keep cows from breaching the fence. That day, Glidden was accompanied by two other men, Isaac L. Ellwood, a hardware dealer and Jacob Haish, a lumber merchant. Like Glidden, they both wanted to create a more durable wire fence with fixed barbs. Glidden experimented with a grindstone to twist two wires together to hold the barbs on the wire in place. They were created from experiments with a coffee mill from his home.[15]
Later Glidden was joined by Ellwood who knew his design could not compete with Glidden's for which he applied for a patent in October 1873.[16] Meanwhile, Haish, who had already secured several patents for barbed wire design, applied over a week before Glidden for a patent on his third type of wire, the S barb, and accused Glidden of interference, deferring Glidden's approval for his patented wire nicknamed "The Winner" until November 24, 1874.[17]
Barbed wire production greatly increased with Glidden and Ellwood’s establishment of the Barb Fence Company in DeKalb following the success of "The Winner". The company's success attracted the attention of Charles Francis Washburn, Vice President of Washburn & Moen Manufacturing Company, an important producer of plain wire in the Eastern U.S. Washburn visited De Kalb and convinced Glidden to sell his stake in the Barb Wire Fence Company, while Ellwood stayed in DeKalb and renamed the company I.L Ellwood & Company of DeKalb.[18]
Promotion and consolidation
In the late 1870s, John Warne Gates of Illinois began to promote barbed wire, now a proven product, in the lucrative markets of Texas. At first, Texans were hesitant, as they feared that cattle might be harmed, or that the North was somehow trying to make profits from the South. There was also conflict between the farmers who wanted fencing and the ranchers who were losing the open range.[12]
Demonstrations by Gates in San Antonio in 1876 showed that the wire could keep cattle contained, and sales then increased dramatically. Gates eventually parted company with Ellwood and became a barbed wire baron in his own right. Throughout the height of barbed wire sales in the late 19th century, Washburn, Ellwood, Gates, and Haish competed with one another, but Ellwood and Gates eventually joined forces again to create the American Steel and Wire Company, later acquired by The U.S. Steel Corporation.[19]
Between 1873 and 1899 there were as many as 150 companies manufacturing barbed wire to cash in on the demand in the West: investors were aware that the business did not require much capital and it was considered that almost anyone with enough determination could make a profit from manufacture of a new wire design.[20] There was then a sharp decline in the number of manufacturing firms, as many were consolidated into larger companies, notably the American Steel and Wire Company, formed by the merging of Gates's and Washburn's and Ellwood's industries.
Smaller companies were wiped out because of economies of scale and the smaller pool of consumers available to them, compared to the larger corporations. The American Steel and Wire Company established in 1899 employed vertical integration: it controlled all aspects of production from producing the steel rods to making many different wire and nail products from the same steel; although later part of U.S. Steel, the production of barbed wire would still be a major source of revenue
Another inventor, William Edenborn, a German immigrant who later settled in Winn Parish, Louisiana, patented a machine which simplified the making of barbed wire and cut the unit price of production from seventeen to three cents per pound. His particular wire is the "humane" version that did not harm cattle. The original wire was sharp-teethed and contributed to western range wars. Edenborn's company in time supplied 75 percent of the barbed wire in the United States. A wire nail machine that he also patented reduced the price of wire nails from eight to two cents per pound.[21][22]
Historical uses
In the American West
![](http://upload.wikimedia.org/wikipedia/commons/thumb/6/65/Salsola_tragus_tumbleweed.jpg/220px-Salsola_tragus_tumbleweed.jpg)
Barbed wire played an important role in the protection of range rights in the Western U.S. Although some ranchers put notices in newspapers claiming land areas, and joined stockgrowers associations to help enforce their claims, livestock continued to cross range boundaries. Fences of smooth wire did not hold stock well, and hedges were difficult to grow and maintain. Barbed wire's introduction in the West in the 1870s dramatically reduced the cost of enclosing land.[23]
![](http://upload.wikimedia.org/wikipedia/commons/thumb/0/05/Rusty_Barbed_Wire.jpg/220px-Rusty_Barbed_Wire.jpg)
One fan wrote the inventor Joseph Glidden:
- it takes no room, exhausts no soil, shades no vegetation, is proof against high winds, makes no snowdrifts, and is both durable and cheap.[24]
Barbed wire also emerged as a major source of conflict with the so-called “Big Die Up” incident in the 1880s. This conflict occurred because of the instinctual migrations of cattle away from the blizzard conditions of the Northern Plains to the warmer and plentiful Southern Plains, but by the early 1880s this area was already divided and claimed by ranchers. The ranchers in place, especially in the Texas Panhandle, knew that their holdings could not support the grazing of additional cattle, so the only alternative was to block the migrations with barb wire fencing.[25]
Many of the herds were decimated in the winter of 1885, with some losing as many as three-quarters of all animals when they could not find a way around the fence. Later other smaller scale cattlemen, especially in central Texas, opposed the closing of the open range, and began cutting fences to allow cattle to pass through to find grazing land. In this transition zone between the agricultural regions to the south and the rangeland to the north, conflict erupted, with vigilantes joining the scene causing chaos and even death. The fence cutters war came to an end with the passage of a Texas law in 1884 that stated among other provisions that fence cutting was a felony; and other states followed, although conflicts still occurred through the opening years of the 20th century.[26] A federal law passed in 1885 forbade stretching such fences across the public domain.[23]
Barbed wire is often cited by historians as the invention that truly tamed the West. Herding large numbers of cattle on open terrain required significant manpower just to catch strays, but with an inexpensive method to divide, sub-divide and allocate parcels of land to control the movement of cattle, the need for a vast labor force became unnecessary. By the beginning of the 20th century the need for significant numbers of cowboys was not necessary.[27]
In war
![](http://upload.wikimedia.org/wikipedia/commons/thumb/b/b3/Daily_Mail_Postcard_-_An_attack_-_A_wiring_party_going_forward.jpg/220px-Daily_Mail_Postcard_-_An_attack_-_A_wiring_party_going_forward.jpg)
Barbed wire was used for the first time in the Spanish–American War during the siege of Santiago by the Spanish defenders. Less well known is its extensive usage in the Russo-Japanese War.
More significantly, barbed wire was used extensively by all participating combatants in World War I to prevent movement, with deadly consequences. Barbed wire entanglements were placed in front of trenches to prevent direct charges on men below, increasingly leading to greater use of more advanced weapons such as high powered machine guns and grenades. A feature of these entanglements was that the barbs were much closer together, often forming a continuous sequence.[28]
Barbed wire could be exposed to heavy bombardments because it could be easily replaced, and its structure included so much open space that machine guns rarely destroyed enough of it to defeat its purpose. However barbed wire was defeated by the tank in 1916, as shown by the Allied breakthrough at Amiens through German lines on August 8, 1918.[29]
In concentration camps
![](http://upload.wikimedia.org/wikipedia/commons/thumb/6/62/OkinawaJapanesePOW.jpg/220px-OkinawaJapanesePOW.jpg)
In 1899 barbed wire was also extensively used in the Boer War, where it played a strategic role bringing spaces under control, at military outposts as well as to hold the captured Boer population in concentration camps.
In the 1930s and 1940s Europe the Nazis used barbed wire in concentration camp architecture, where it usually surrounded the camp and was electrified to prevent escape. Barbed wire served the purpose of keeping prisoners contained.
Infirmaries in extermination camps like Auschwitz where prisoners were gassed or experimented on were often separated from other areas by electrified wire and were often braided with branches to prevent outsiders from knowing what was concealed behind their walls.[30]
In the Southwest United States
John Warne Gates demonstrated barbed wire for Washburn and Moen in Military Plaza, San Antonio, Texas in 1876. The demonstration showing cattle restrained by the new kind of fencing was followed immediately by invitations to the Menger Hotel to place orders. Gates subsequently had a falling out with Washburn and Moen and Isaac Ellwood. He moved to St. Louis and founded the Southern Wire Company, which became the largest manufacturer of unlicensed or "bootleg" barbed wire.
An 1880 US District Court decision upheld the validity of the Glidden patent, effectively establishing a monopoly. This decision was affirmed by the US Supreme Court in 1892. In 1898 Gates took control of Washburn and Moen, and created the American Steel and Wire monopoly, which became a part of the United States Steel Corporation.
This led to disputes known as the range wars between open range ranchers and farmers in the late 19th century. These were similar to the disputes which resulted from enclosure laws in England in the early 18th century. These disputes were decisively settled in favor of the farmers, and heavy penalties were instituted for cutting a barbed wire fence. Within 2 years, nearly all of the open range had been fenced in under private ownership. For this reason, some historians have dated the end of the Old West era of American history to the invention and subsequent proliferation of barbed wire.
Agricultural fencing
![](http://upload.wikimedia.org/wikipedia/commons/thumb/c/c5/Barbed_wire.jpg/220px-Barbed_wire.jpg)
Barbed wire fences remain the standard fencing technology for enclosing cattle in most regions of the US, but not all countries. The wire is aligned under tension between heavy, braced, fence posts (strainer posts) and then held at the correct height by being attached to wooden or steel fence posts, and/or with battens in between.
The gaps between posts vary depending on type and terrain. On short fences in hilly country, steel posts may be placed every 3 yards (2.7 m), while in flat terrain with long spans and relatively few stock they may be spaced up to 30 to 50 yards (46 m). Wooden posts are normally spaced at 11 yards (10 m) (2 rods) on all terrain, with 4 or 5 battens in between. However, many farmers place posts 2 yards (1.8 m) apart as battens can bend, causing wires to close in on one another.
Barbed wire for agricultural fencing is typically available in two varieties: soft or mild-steel wire and high-tensile. Both types are galvanized for longevity. High-tensile wire is made with thinner but higher-strength steel. Its greater strength makes fences longer lasting because it resists stretching and loosening better, coping with expansion and contraction caused by heat and animal pressure by stretching and relaxing within wider elastic limits. It also supports longer spans, but because of its elastic (springy) nature it is harder to handle and somewhat dangerous for inexperienced fencers. Soft wire is much easier to work but is less durable and only suitable for short spans such as repairs and gates, where it is less likely to tangle.
In high soil-fertility areas where dairy cattle are used in great numbers 5- or 7-wire fences are common as the main boundary and internal dividing fences. On sheep farms 7-wire fences are common with the second (from bottom) to fifth wire being plain wire. In New Zealand wire fences must provide passage for dogs since they are the main means of controlling and driving animals on farms.
Gates
![](http://upload.wikimedia.org/wikipedia/commons/thumb/8/85/Wire_gate.jpg/220px-Wire_gate.jpg)
As with any fence, barbed wire fences require gates to allow the passage of persons, vehicles and farm implements. Gates vary in width from 12 feet (3.7 m) to allow the passage of vehicles and tractors, to 40 feet (12 m) on farm land to pass combines and swathers.
One style of gate is called the Hampshire gate in the UK, a New Zealand gate in some areas, and often simply a "gate" elsewhere. Made of wire with posts attached at both ends and in the middle, it is permanently wired on one side and attaches to a gate post with wire loops on the other. Most designs can be opened by hand, though some gates that are frequently opened and closed may have a lever attached to assist in bringing the upper wire loop over the gate post
Gates for cattle tend to have 4 wires when along a three wire fence, as cattle tend to put more stress on gates, particularly on corner gates. The fence on each side of the gated ends with two corner posts braced or unbraced depending on the size of the post. An unpounded post (often an old broken post) is held to one corner post with wire rings which act as hinges. On the other end a full length post, the tractor post, is placed with the pointed end upwards with a ring on the bottom stapled to the other corner post, the latch post, and on top a ring is stapled to the tractor post, the post is tied with a Stockgrower's Lash or one of numerous other opening bindings. Wires are then tied around the post at one end then run to the other end where they are stretched by hand or with a stretcher, before posts are stapled on every 4 feet (1.2 m), often this type of gate is called a portagee fence or a portagee gate in various ranching communities of coastal Central California.
Most gates can be opened by push post. The chain is then wrapped around the tractor post and pulled onto the nail, stronger people can pull the gate tighter but anyone can jar off the chain to open the gate.
Human-proof fencing
![](http://upload.wikimedia.org/wikipedia/commons/thumb/8/83/2008-08-01_No_Tresspassing_sign_at_RDU.jpg/220px-2008-08-01_No_Tresspassing_sign_at_RDU.jpg)
Most barbed wire fences, while sufficient to discourage cattle, are passable by humans who can simply climb over the fence, or through the fence by stretching the gaps between the wires using non-barbed sections of the wire as hand holds. To prevent humans crossing, many prisons and other high-security installations construct fences with razor wire, a variant which instead of occasional barbs features near-continuous cutting surfaces sufficient to injure unprotected persons who climb on it. However, it has been banned in the United Kingdom; and any person(s) erecting anti-human wire fences can be prosecuted under applicable laws.[citation needed]
A commonly seen alternative is the placement of a few strands of barbed wire at the top of a chain link fence. The limited mobility of someone climbing a fence makes passing conventional barbed wire more difficult. On some chain link fences these strands are attached to a bracket tilted 45 degrees towards the intruder, further increasing the difficulty.
Barbed wire began to be widely used as an implement of war during World War I. Wire was placed either to impede or halt the passage of soldiers, or to channel them into narrow defiles in which small arms, particularly machine guns, and indirect fire could be used with greater effect as they attempted to pass. Artillery bombardments on the Western Front became increasingly aimed at cutting the barbed wire that was a major component of trench warfare, particularly once new "wire-cutting" fuzes were introduced midway through the war.
As the war progressed the wire was used in shorter lengths that were easier to transport and more difficult to cut with artillery. Other inventions were also a result of the war, such as the screw picket, which enabled construction of wire obstacles to be done at night in No Man's Land without the necessity of hammering stakes into the ground and drawing attention from the enemy.
![](http://upload.wikimedia.org/wikipedia/commons/thumb/5/5f/Razor_Barb_Wire_Philadelphia_PA.jpg/220px-Razor_Barb_Wire_Philadelphia_PA.jpg)
During the Soviet-Afghan War, the accommodation of Afghan refugees into Pakistan was controlled in Pakistan's largest province, Balochistan, under General Rahimuddin Khan, by making the refugees stay for controlled durations in barbed wire camps (see Controlling Soviet-Afghan War Refugees).
The frequent use of barbed wire on prison walls, around concentration camps, and the like, has made it symbolic of oppression and denial of freedom in general. For example, in Germany the totality of the complex German Democratic Republic border regime is commonly referred to with the short phrase "Mauer und Stacheldraht" (that is, "wall and barbed wire"), and Amnesty International has a barbed wire in their symbol. Recently, Britain and France have begun restricting the use of barbed wire due to the risk of injury it poses to trespassers.[31]
Injuries caused by barbed wire
![](http://upload.wikimedia.org/wikipedia/commons/thumb/0/07/Drut_kolczasty_cm01.jpg/220px-Drut_kolczasty_cm01.jpg)
Movement against barbed wire can result in moderate to severe injuries to the skin and, depending on body area and barbed wire configuration, possibly to the underlying tissue. Humans can manage not to injure themselves excessively when dealing with barbed wire as long as they are cautious. Restriction of movement, appropriate clothing, and slow movement when close to barbed wire aid in reducing injury.
Infantrymen are often trained and inured to the injuries caused by barbed wire. Several soldiers can lie across the wire to form a bridge for the rest of the formation to pass over; often any injury thus incurred is due to the tread of those passing over and not to the wire itself.[citation needed]
Injuries caused by barbed wire are typically seen in horses, bats, or birds. Horses panic easily, and once caught in barbed wire, large patches of skin may be torn off. At best, such injuries may heal, but they may cause disability or death (particularly due to infection). Birds or bats may not be able to perceive thin strands of barbed wire and suffer injuries.
For this reason horse fences may have rubber bands nailed parallel to the wires. More than 60 different species of wildlife have been reported in Australia as victims of entanglement on barbed wire fences, and the wildlife friendly fencing project is beginning to address this problem. [citation needed] Grazing animals with slow movements that will back off at the first notion of pain (e.g., sheep and cows) will not generally suffer the severe injuries often seen in other animals.
Barbed wire has been reported as a tool for human torture.[32] It is also frequently used as a weapon in hardcore professional wrestling matches, often as a covering for another type of weapon—Mick Foley was infamous for using a baseball bat wrapped in barbed wire—and infrequently as a covering of or substitute for the ring ropes.
Installation of barbed wire
![](http://upload.wikimedia.org/wikipedia/commons/thumb/8/81/Barbedwire3.jpg/220px-Barbedwire3.jpg)
The most important and most time-consuming part of a barbed wire fence is constructing the corner post and the bracing assembly. A barbed wire fence is under tremendous tension, often up to half a ton, and so the corner post's sole function is to resist the tension of the fence spans connected to it. The bracing keeps the corner post vertical and prevents slack from developing in the fence.
Brace posts are placed in-line about 8 feet (2.4 m) from the corner post. A horizontal compression brace connects the top of the two posts, and a diagonal wire connects the top of the brace post to the bottom of the corner post. This diagonal wire prevents the brace post from leaning, which in turn allows the horizontal brace to prevent the corner post from leaning into the brace post. A second set of brace posts (forming a double brace) is used whenever the barbed wire span exceeds 200 feet (61 m).
When the barbed wire span exceeds 650 ft (200 m), a braced line assembly is added in-line. This has the function of a corner post and brace assembly but handles tension from opposite sides. It uses diagonal brace wire that connects the tops to the bottoms of all adjacent posts.
Line posts are installed along the span of the fence at intervals of 8 to 50 ft (2.4 to 15.2 m). An interval of 16 ft (4.9 m) is most common. Heavy livestock and crowded pasture demands the smaller spacing. The sole function of a line post is not to take up slack but to keep the barbed wire strands spaced equally and off the ground.
Once these posts and bracing have been erected, the wire is wrapped around one corner post, held with a hitch (a timber hitch works well for this) often using a staple to hold the height and then reeled out along the span of the fence replacing the role every 400 m. It is then wrapped around the opposite corner post, pulled tightly with wire stretchers, and sometimes nailed with more fence staples, although this may make readjustment of tension or replacement of the wire more difficult. Then it is attached to all of the line posts with fencing staples driven in partially to allow stretching of the wire.
There are several ways to anchor the wire to a corner post:
- Hand-knotting. The wire is wrapped around the corner post and knotted by hand. This is the most common method of attaching wire to a corner post. A timber hitch works well as it stays better with wire than with rope.
- Crimp sleeves. The wire is wrapped around the corner post and bound to the incoming wire using metal sleeves which are crimped using lock cutters. This method should be avoided because while sleeves can work well on repairs in the middle of the fence where there is not enough wire for hand knotting, they tend to slip when under tension.
- Wire vise. The wire is passed through a hole drilled into the corner post and is anchored on the far side.
- Wire wrap. The wire is wrapped around the corner post and wrapped onto a special, gritted helical wire which also wraps around the incoming wire, with friction holding it in place.
Barbed wire for agriculture use is typically double-strand 12½-gauge, zinc-coated (galvanized) steel and comes in rolls of 1,320 ft (400 m) length. Barbed wire is usually placed on the inner (pasture) side of the posts. Where a fence runs between two pastures livestock could be with the wire on the outside or on both sides of the fence.
Galvanized wire is classified into three categories; Classes I, II, and III. Class I has the thinnest coating and the shortest life expectancy. A wire with Class I coating will start showing general rusting in 8 to 10 years, while the same wire with Class III coating will show rust in 15 to 20 years. Aluminum-coated wire is occasionally used, and yields a longer life.
Corner posts are 6 to 8 inches (15 to 20 cm) in diameter or larger, and a minimum 8 feet (2.4 m) in length may consist of treated wood or from durable on-site trees such as osage orange, black locust, red cedar, or red mulberry, also railroad ties, telephone, and power poles are salvaged to be used as corner posts (poles and railroad ties were often treated with chemicals determined to be an environmental hazard and cannot be reused in some jurisdictions). In Canada spruce posts are sold for this purpose. Posts are 4 inches (10 cm) in diameter driven at least 4 feet (1.2 m) and may be anchored in a concrete base 20 inches (51 cm) square and 42 inches (110 cm) deep. Iron posts, if used, are a minimum 2.5 inches (64 mm) in diameter. Bracing wire is typically smooth 9-gauge. Line posts are set to a depth of about 30 inches (76 cm). Conversely, steel posts are not as stiff as wood, and wires are fastened with slips along fixed teeth, which means variations in driving height affect wire spacing.
During the First World War, screw pickets were used for the installation of wire obstacles; these were metal rods with eyelets for holding strands of wire, and a corkscrew-like end that could literally be screwed into the ground rather than hammered, so that wiring parties could work at night near enemy soldiers and not reveal their position by the sound of hammers.
See also
Military:
- Bangalore torpedo, used in World War I and II to breach barbed wire obstacles
- Concertina wire
- Wire obstacle
Notes
- ^ "Fencing Frontiers: The Barbed Wire Story". Ellwood House Museum, DeKalb, IL. Archived from the original on 2006-07-12. Retrieved 2006-11-27. Glidden Steel called its product "Barb Wire".
- ^ Timothy Foote (September 6, 1998). "The Rape of the West". The New York Times. Retrieved 2006-11-28. "In my book a pioneer is a man who turned all the grass upside down, strung bob-wire over the dust that was left, poisoned the water, cut down the trees, killed the Indian who owned the land and called it progress." Timothy Egan is quoting a surprising source, the celebrated cowboy artist Charles Russell.
- ^ "A Collection of Barbed Wire". The Murray County Museum. Archived from the original on 2011-07-14. Retrieved 2006-11-28.
- ^ "The American Experience Technology Timeline: 1752 - 1990". The American Experience. Public Broadcasting Systems. 2000. Archived from the original on 7 February 2009. Retrieved 2009-01-28.
{{cite web}}
: Unknown parameter|deadurl=
ignored (|url-status=
suggested) (help) - ^ "Lucien B. Smith". Ohio History Central. Ohio Historical Society. 31 July 2006. Archived from the original on 2007-10-03. Retrieved 2009-01-28.
- ^ Carlisle, Rodney (2004). Scientific American Inventions and Discoveries, p. 241. John Wiley & Songs, Inc., New Jersey. ISBN 0-471-24410-4.
- ^ Winchell, Lilbourne. History of Fresno County and the San Joaquin Valley. p. 107.
- ^ John Crow, "The Epic of Latin America, University of California Press; 4th edition (January 17, 1992) "
- ^ Alan Krell, The Devil's Rope: A Cultural History of Barbed Wire (London: Reaktion Books Ltd, 2002), p.16.
- ^ Alan Krell, The Devil's Rope: A Cultural History of Barbed Wire (London: Reaktion Books Ltd, 2002), p.19.
- ^ Netz 2004, p. 10
- ^ a b Alan Krell, The Devil's Rope: A Cultural History of Barbed Wire (London: Reaktion Books Ltd, 2002), p.28.
- ^ McCallum 1965, p. 27
- ^ Alan Krell, The Devil's Rope: A Cultural History of Barbed Wire (London: Reaktion Books Ltd, 2002), p.23.
- ^ a b Template:Wayback, Devil's Rope Museum
- ^ McCallum 1965, pp. 29-32
- ^ McCallum 1965, p. 41
- ^ McCallum 1965, p. 87
- ^ Joseph M., McFadden, "Monopoly in Barbed Wire: The Formation of the American Steel and Wire Company." The Business History Review, 52,4,1978, p. 2.
- ^ Joseph M., McFadden, "Monopoly in Barbed Wire: The Formation of the American Steel and Wire Company." The Business History Review, 52,4,1978, p. 5
- ^ "Greggory E. Davies, William Edenborn of Winn Parish, La". files.usgwarchives.net. Retrieved March 26, 2014.
- ^ Glen Coleman, great-nephew of William Edenborn, wrote The Man Who Fenced the West about his uncle's accomplishments regarding barbed wire.
- ^ a b Anderson, Terry Lee and Leal, Donald (2001). Free Market Environmentalism. 0-312-23503-8. pp. 30–31.
{{cite book}}
: CS1 maint: multiple names: authors list (link) - ^ See "1873: Joseph Glidden applies for a patent on his barbed wire design" History Channel
- ^ McCallum 1965, p. 131
- ^ McCallum 1965, pp. 165-166
- ^ "Honoring the Wire That Won the West". latimes. Retrieved 26 October 2015.
- ^ Netz 2004, p. 108
- ^ Netz 2004, pp. 124–127
- ^ Razac 2003, p. 89
- ^ "No barbed wire...it might hurt the thieves, allotment holders told". Daily Mail. London. October 9, 2008.
- ^ Ferriman, Annabel (2002-02-09). "Human rights group uncovers evidence of torture in Zimbabwe". BMJ Publishing Group Ltd. Archived from the original on February 12, 2008. Retrieved 2007-08-28.
{{cite web}}
: Unknown parameter|deadurl=
ignored (|url-status=
suggested) (help)
References
- Krell, Alan (2002). The Devil's Rope: A Cultural History of Barbed Wire. London: Reaktion Books. ISBN 186189144X. OCLC 50494711.
{{cite book}}
: Invalid|ref=harv
(help) - McCallum, Henry D. & Frances T. (1965). The Wire that Fenced the West. Norman: University of Oklahoma Press.
{{cite book}}
: Invalid|ref=harv
(help), LoC:65-11234 - Netz, Reviel (2004). Barbed wire. An ecology of modernity. Wesleyan University Press. ISBN 978-0-8195-6719-2.
{{cite book}}
: Invalid|ref=harv
(help) - Razac, Olivier (2003). Barbed Wire: A Political History. W. W. Norton & Company. ISBN 1-56584-812-8.
{{cite book}}
: Invalid|ref=harv
(help) - Biography of John W. Gates, barbed wire promoter who monopolized the industry with the American Steel and Wire Company, accessed March 29, 2006
External links
![](http://upload.wikimedia.org/wikipedia/en/thumb/4/4a/Commons-logo.svg/30px-Commons-logo.svg.png)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/9/99/Wiktionary-logo-en-v2.svg/40px-Wiktionary-logo-en-v2.svg.png)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/4/4c/Wikisource-logo.svg/38px-Wikisource-logo.svg.png)
Information
- Website of the Devils Rope Museum in McLean, Texas
- The Kansas Barbed Wire Museum in La Crosse, Kansas is the only museum in the world dedicated solely to barbed wire and the history of fencing. Template:Wayback
- Barbed Wire Photo Gallery: DeKalb photos included, barbed wire examples pgs. 3 thru 24.
- Development and Rise of Barbed Wire at University of Virginia accessed March 29, 2006
- Barbed Wire Fencing - Its Rise and Influence also at UVA, from Agricultural History, Volume 13, October 1939, accessed September 20, 2006
- Glidden's patent for barbed wire accessed March 29, 2006
- Antique Barbed Wire Society accessed September 21, 2006
- Barbed Wire in Texas
- Barbed wire changes life on the American Great Plains
- The History of Barbed Wire About.com
- The Wildlife Friendly Fencing project
- Papers, 1878-1938, of Texas rancher and co-inventor Isaac L. Ellwood in Southwest Collection/Special Collections Library at Texas Tech University
Patents – (about 570 were issued):
- Template:Wayback accessed September 21, 2006
- U.S. patent 66,182 – Lucien Smith, Kent, Ohio, Wire fence – "rotary spools with projecting spurs" (June 1867)
- U.S. patent 67,117 – William Hunt, Scott, New York, Improvement in Fences – "sharpened spur wheels" (July 1867)
- U.S. patent 74,379 – Michael Kelly, New York City (!), Improvement in Fences – "thorny fence" (1868)
- U.S. patent 116,755 – Joshua Rappleye, Seneca County, New York, Improvement in Constructing Wire fence – tensioner for fence with palings (pickets) (1871)
- U.S. patent 138,763 – Henry Rose, DeKalb County, Illinois, Improvement in Wire-fences – "strips provided with metal points" (1873)
- U.S. patent 147,756 – Isaac Ellwood, DeKalb, Illinois Improvement in Barbed Fences – "single piece of metal with four points, attached to a flat rail" (February, 1874)
- U.S. patent 157,124 – Joseph Glidden, DeKalb, Illinois, Improvement in Wire-fences – twisted fence wires with short spur coiled around one of the strands (November, 1874) This became the most popular patent.
- U.S. patent 167,240 – Jacob Haish, DeKalb, Illinois, Improvement in Wire-fence Barbs – "single piece of wire bent into the form of the letter S" so that both strands are clasped (1875)
- U.S. patent 185,346 – John Nelson, Creston, Illinois, Improvement in Wire-fence Barbs – barb installable on existing fence wire, (1876)