Double arch stone bridge, Japan
|Descendant||Truss arch bridge, moon bridge (masonry)|
|Carries||Pedestrians, vehicles, light rail, heavy rail, water|
|Span range||short, but often set end-to-end to form a large total length|
|Material||masonry, concrete, wrought iron, cast iron, timber, structural steel|
An arch bridge is a bridge with abutments at each end shaped as a curved arch. Arch bridges work by transferring the weight of the bridge and its loads partially into a horizontal thrust restrained by the abutments at either side. A viaduct (a long bridge) may be made from a series of arches, although other more economical structures are typically used today.
- 1 History
- 2 Simple compression arch bridges
- 3 Types of arch bridge
- 4 Gallery
- 5 Use of modern materials
- 6 See also
- 7 Footnotes
- 8 References
- 9 External links
Possibly the oldest existing arch bridge is the Mycenaean Arkadiko bridge in Greece from about 1300 BC. The stone corbel arch bridge is still used by the local populace. The well-preserved Hellenistic Eleutherna Bridge has a triangular corbel arch. The 4th century BC Rhodes Footbridge rests on an early voussoir arch.
Although true arches were already known by the Etruscans and ancient Greeks, the Romans were - as with the vault and the dome - the first to fully realize the potential of arches for bridge construction. A list of Roman bridges compiled by the engineer Colin O'Connor features 330 Roman stone bridges for traffic, 34 Roman timber bridges and 54 Roman aqueduct bridges, a substantial part still standing and even used to carry vehicles. A more complete survey by the Italian scholar Vittorio Galliazzo found 931 Roman bridges, mostly of stone, in as many as 26 different countries (including former Yugoslavia).
Roman arch bridges were usually semicircular, although a number were segmental arch bridges (such as Alconétar Bridge), a bridge which has a curved arch that is less than a semicircle. The advantages of the segmental arch bridge were that it allowed great amounts of flood water to pass under it, which would prevent the bridge from being swept away during floods and the bridge itself could be more lightweight. Generally, Roman bridges featured wedge-shaped primary arch stones (voussoirs) of the same in size and shape. The Romans built both single spans and lengthy multiple arch aqueducts, such as the Pont du Gard and Segovia Aqueduct. Their bridges featured from an early time onwards flood openings in the piers, e.g. in the Pons Fabricius in Rome (62 BC), one of the world's oldest major bridges still standing.
Roman engineers were the first and until the industrial revolution the only ones to construct bridges with concrete, which they called Opus caementicium. The outside was usually covered with brick or ashlar, as in the Alcántara bridge.
The Romans also introduced segmental arch bridges into bridge construction. The 330 m long Limyra Bridge in southwestern Turkey features 26 segmental arches with an average span-to-rise ratio of 5.3:1, giving the bridge an unusually flat profile unsurpassed for more than a millennium. Trajan's bridge over the Danube featured open-spandrel segmental arches made of wood (standing on 40 m high concrete piers). This was to be the longest arch bridge for a thousand years both in terms of overall and individual span length, while the longest extant Roman bridge is the 790 m long Puente Romano at Mérida. The late Roman Karamagara Bridge in Cappadocia may represent the earliest surviving bridge featuring a pointed arch.
In medieval Europe, bridge builders improved on the Roman structures by using narrower piers, thinner arch barrels and lower span-rise ratios on bridges. Gothic pointed arches were also introduced, reducing lateral thrust, and spans increased as with the eccentric Puente del Diablo (1282).
The 14th century in particular saw bridge building reaching new heights. Span lengthes of 40 m, previously unheard of in the history of masonry arch construction, were now reached in places as diverse as Spain (Puente de San Martín), Italy (Castelvecchio Bridge) and France (Devil's bridge and Pont Grand) and with arch types as different as semi-circular, pointed and segmental arches. The bridge at Trezzo sull'Adda, destroyed in the 15th century, even featured a span length of 72 m, not matched until 1796.
Constructions such as the acclaimed Florentine segmental arch bridge Ponte Vecchio (1345) combined sound engineering (span-to-rise ratio of over 5.3 to 1) with aesthetical appeal. The three elegant arches of the Renaissance Ponte Santa Trinita (1569) constitute the oldest elliptic arch bridge worldwide. Such low rising structures required massive abutments, which at the Venetian Rialto bridge and the Fleischbrücke in Nuremberg (span-to-rise ratio 6.4:1) were founded on thousands of wooden piles, partly rammed obliquely into the grounds to counteract more effectively the lateral thrust.
In China, the oldest existing arch bridge is the Zhaozhou Bridge of 605 AD, which combined a very low span-to-rise ratio of 5.2:1, with the use of spandrel arches (buttressed with iron brackets). The Zhaozhou Bridge, with a length of 167 feet (51 m) and span of 123 feet (37 m), is the world's first wholly stone open-spandrel segmental arch bridge, allowing a greater passage for flood waters. Bridges with perforated spandrels can be found worldwide, such as in China (Anji Bridge, 7th century). Greece (Bridge of Arta, 17th century) and Wales (Cenarth Bridge, 18th century).
In more modern times, stone and brick arches continued to be built by many civil engineers, including Thomas Telford, Isambard Kingdom Brunel and John Rennie. A key pioneer was Jean-Rodolphe Perronet, who used much narrower piers, revised calculation methods and exceptionally low span-to-rise ratios. Different materials, such as cast iron, steel and concrete have been increasingly used in the construction of arch bridges.
Simple compression arch bridges
Advantages of simple materials
Stone, brick and other such materials are strong in compression and somewhat so in shear, but cannot resist much force in tension. As a result, masonry arch bridges are designed to be constantly under compression, so far as is possible. Each arch is constructed over a temporary falsework frame, known as a centring. In the first compression arch bridges, a keystone in the middle of the bridge bore the weight of the rest of the bridge. The more weight that was put onto the bridge, the stronger its structure became. Masonry arch bridges use a quantity of fill material (typically compacted rubble) above the arch in order to increase this dead-weight on the bridge and prevent tension from occurring in the arch ring as loads move across the bridge. Other materials that were used to build this type of bridge were brick and unreinforced concrete. When masonry (cut stone) is used the angles of the faces are cut to minimize shear forces. Where random masonry (uncut and unprepared stones) is used they are mortared together and the mortar is allowed to set before the falsework is removed.
Traditional masonry arches are generally durable, and somewhat resistant to settlement or undermining. However, relative to modern alternatives, such bridges are very heavy, requiring extensive foundations. They are also expensive to build wherever labor costs are high.
- Where the arches are founded in a watercourse bed (on piers or banks) the water is diverted so the gravel can first be excavated and replaced with a good footing (of strong material). From these, the foundation piers are erected/raised to the height of the intended base of the arches, a point known as the springing.
- Falsework centering (in British English: arch frame) is fabricated, typically from timbers and boards. Since each arch of a multi-arch bridge will impose a thrust upon its neighbors, it is necessary either that all arches of the bridge be raised at the same time, or that very wide piers be used. The thrust from the end arches is taken into the earth by substantial (vertical) footings at the canyon walls, or by large inclined planes forming in a sense ramps to the bridge, which may also be formed of arches.
- The several arches are (or single arch is) constructed over the centering. Once each basic arch barrel is constructed, the arches are (or arch is) stabilized with infill masonry above, which may be laid in horizontal running bond courses (layers). These may form two outer walls, known as the spandrels, which are then infilled with appropriate loose material and rubble.
- The road is paved and parapet walls protectively confine traffic to the bridge.
Types of arch bridge
Corbel arch bridge
The corbel arch bridge is a masonry, or stone, bridge where each successively higher course (layer) cantilevers slightly more than the previous course. The steps of the masonry may be trimmed to make the arch have a rounded shape. The corbel arch does not produce thrust, or outward pressure at the bottom of the arch, and is not considered a true arch. It is more stable than a true arch because it does not have this thrust. The disadvantage is that this type of arch is not suitable for large spans.
Aqueducts and canal viaducts
In some locations it is necessary to span a wide gap at a relatively high elevation, such as when a canal or water supply must span a valley. Rather than building extremely large arches, or very tall supporting columns (difficult using stone), a series of arched structures are built one atop another, with wider structures at the base. Roman civil engineers developed the design and constructed highly refined structures using only simple materials, equipment, and mathematics. This type is still used in canal viaducts and roadways as it has a pleasing shape, particularly when spanning water, as the reflections of the arches form a visual impression of circles or ellipses.
Deck arch bridge
This type of bridge comprises an arch where the deck is completely above the arch. The area between the arch and the deck is known as the spandrel. If the spandrel is solid, usually the case in a masonry or stone arch bridge, the bridge is called a closed-spandrel arch bridge. If the deck is supported by a number of vertical columns rising from the arch, the bridge is known as an open-spandrel arch bridge. The Alexander Hamilton Bridge is an example of an open-spandrel arch bridge. Finally, if the arch supports the deck only at the top of the arch, the bridge is called a cathedral arch bridge.
See also: Category:Deck arch bridges.
Through arch bridge
See also: Category:Through arch bridges.
This type of bridge comprises an arch which supports the deck:
- in the centre, from above, by means of suspension cables or tie bars, as with a tied-arch bridge.
- at the edges, from below, as with a deck arch bridge.
The Sydney Harbour Bridge is a through arch bridge which uses a truss type arch.
Also known as a bowstring arch, this type of arch bridge incorporates a tie between two opposite ends of the arch. The tie is usually the deck and is capable of withstanding the horizontal thrust forces which would normally be exerted on the abutments of an arch bridge.
The deck is suspended from the arch. The arch is in compression, in contrast to a suspension bridge where the catenary is in tension. A tied-arch bridge can also be a through arch bridge.
Pointed arch of the Puente del Diablo in Spain
Late medieval Krämerbrücke supporting two rows of houses
Ponte Santa Trinita. First bridge with elliptic arches
A masonry moon bridge showing the buttressing approach ramps that take the horizontal thrust of the arch
Bridgeport Lamp Chimney Company Bowstring Concrete Arch Bridge located in Bridgeport, West Virginia
Use of modern materials
Most modern arch bridges are made from reinforced concrete. This type of bridge is suitable where a temporary centring may be erected to support the forms, reinforcing steel, and uncured concrete. When the concrete is sufficiently set the forms and falseworks are then removed. It is also possible to construct a reinforced concrete arch from precast concrete, where the arch is built in two halves which are then leaned against each other.
Many modern bridges, made of steel or reinforced concrete, often bear some of their load by tension within their structure. This reduces or eliminates the horizontal thrust against the abutments and allows their construction on weaker ground. Structurally and analytically they are not true arches but rather a beam with the shape of an arch. See truss arch bridge for more on this type.
A modern evolution of the arch bridge is the long-span through arch bridge. This has been made possible by the use of light materials that are strong in tension such as steel and prestressed concrete.
- Hellenic Ministry of Culture: Mycenaean bridge at Kazarma
- Nakassis, Athanassios (2000): "The Bridges of Ancient Eleutherna", The Annual of the British School at Athens, Vol. 95, pp. 353–365
- Galliazzo 1995, p. 36; Boyd 1978, p. 91
- Robertson, D.S.: Greek and Roman Architecture, 2nd edn., Cambridge 1943, p.231:
"The Romans were the first builders in Europe, perhaps the first in the world, fully to appreciate the advantages of the arch, the vault and the dome."
- Colin O'Connor: "Roman Bridges", Cambridge University Press 1993, p. 187ff. ISBN 0-521-39326-4
- Galliazzo, Vittorio (1994), I ponti romani. Catalogo generale, Vol. 2, Treviso: Edizioni Canova, ISBN 88-85066-66-6, cf. Indice
- Beall, Christine (1988). "Designing the segmental arch" (PDF). ebuild.com. Retrieved 8 May 2010.
- Temple, Robert. The Genius of China: 3,000 Years of Science, Discovery, and Invention. New York: Touchstone, 1986.
- Colin O'Connor: "Roman Bridges", Cambridge University Press 1993, p. 126 ISBN 0-521-39326-4
- Galliazzo 1995, pp. 92, 93 (fig. 39)
- Leonardo Fernández Troyano: Bridge Engineering. A Global Perspective, Thomas Telford Publishing, London 2003, ISBN 0-7277-3215-3, p.49
- Needham, Joseph. The Shorter Science and Civilisation in China. Cambridge University Press, 1994. ISBN 0-521-29286-7. Pages 145-147.
- Richman, Steven M. (2005), The Bridges of New Jersey, Rutgers University Press, p. 23, ISBN 978-0-8135-3510-4
- Harris, Cyril M. (1983), Illustrated Dictionary of Historic Architecture, Courier Dover Publications, p. 137, ISBN 978-0-486-24444-0
- Simpson, Frederick Moore (1913), A history of architectural development, Longmans, Green, and Co., p. 25
- Durski, Brad F. (Winter 2010). "Nevada's Galena Creek Bridge" (PDF). Aspire. Precast/Prestressed Concrete Institute. Retrieved 2012-06-18.
- Questions and Answers on National Bridge Inspection Standards, FHWA, "What is a bridge?", June 21, 2005.
- Boyd, Thomas D. (1978), "The Arch and the Vault in Greek Architecture", American Journal of Archaeology 82 (1): 83–100 (91), doi:10.2307/503797
- Galliazzo, Vittorio (1995), I ponti romani, Vol. 1, Treviso: Edizioni Canova, ISBN 88-85066-66-6
- Galliazzo, Vittorio (1994), I ponti romani. Catalogo generale, Vol. 2, Treviso: Edizioni Canova, ISBN 88-85066-66-6
- O’Connor, Colin (1993), Roman Bridges, Cambridge University Press, p. 129, ISBN 0-521-39326-4
- Proske, Dirk (2009), Safety of historical stone arch bridges, Springer, p. 336, ISBN 978-3-540-77616-1
|Wikimedia Commons has media related to Arch bridges.|
- NOVA Online - Super Bridge - Arch Bridges
- Matsuo Bridge Co. - Arch Bridges
- Historic Bridges of the Midwest
- Historic Arch Railroad Bridges in Western Massachusetts