List of International Organization for Standardization standards, 1-4999

From Wikipedia, the free encyclopedia
  (Redirected from ISO 8)
Jump to navigation Jump to search

This is a list of published[Note 1] International Organization for Standardization (ISO) standards and other deliverables.[Note 2] For a complete and up-to-date list of all the ISO standards, see the ISO catalogue.[1]

The standards are protected by copyright and most of them must be purchased. However, about 300 of the standards produced by ISO and IEC's Joint Technical Committee 1 (JTC1) have been made freely and publicly available.[2]

ISO 1 – ISO 99[edit]

  • ISO 1:2016 Geometrical product specifications (GPS) - Standard reference temperature for the specification of geometrical and dimensional properties
  • ISO 2:1973 Textiles – Designation of the direction of twist in yarns and related products
  • ISO 3:1973 Preferred numbers – Series of preferred numbers
  • ISO 4:1997 Information and documentation – Rules for the abbreviation of title words and titles of publications
  • ISO 5 Photography and graphic technology – Density measurements
  • ISO 6:1993 Photography – Black-and-white pictorial still camera negative film/process systems – Determination of ISO speed
  • ISO 7 Pipe threads where pressure-tight joints are made on the threads
  • ISO 8:1977 Documentation – Presentation of periodicals
  • ISO 9:1995 Information and documentation – Transliteration of Cyrillic characters into Latin characters – Slavic and non-Slavic languages
  • ISO 11:1987 Aircraft – Ground pressure testing connections for pressure cabins
  • ISO 12:1987 Aerospace – Pipelines – Identification
  • ISO 14:1982 Straight-sided splines for cylindrical shafts with internal centering – Dimensions, tolerances and verification
  • ISO 15:2017 Rolling bearings – Radial bearings – Boundary dimensions, general plan
  • ISO 16:1975 Acoustics – Standard tuning frequency (Standard musical pitch)
  • ISO 17:1973 Guide to the use of preferred numbers and of series of preferred numbers
  • ISO 18:1981 Documentation – Contents list of periodicals
  • ISO 21:1985 Shipbuilding – Inland navigation – Cable-lifters for stud-link anchor chains
  • ISO 22:1991 Belt drives – Flat transmission belts and corresponding pulleys – Dimensions and tolerances
  • ISO 23:1993 Cinematography—Camera usage of 35 mm motion-picture film—Specifications
  • ISO 25:1994 Cinematography—Camera usage of 16 mm motion-picture film—Specifications
  • ISO 26:1993 Cinematography—Projector usage of 16 mm motion-picture films for direct front projection—Specifications
  • ISO 28:1976 Cinematography—Camera usage of 8 mm Type R motion-picture film—Specifications
  • ISO 29:1980 Cinematography—Projector usage of 8 mm Type R silent motion-picture film for direct front projection—Specifications [Withdrawn without replacement]
  • ISO 31 Quantities and units [withdrawn: replaced with ISO/IEC 80000]
  • ISO 32:1977 Gas cylinders for medical use—Marking for identification of content
  • ISO 34 Rubber, vulcanized or thermoplastic—Determination of tear strength
    • ISO 34-1:2015 Part 1: Trouser, angle and crescent test pieces
    • ISO 34-2:2015 Part 2: Small (Delft) test pieces
  • ISO 35:2004 Natural rubber latex concentrate—Determination of mechanical stability
  • ISO 36:2017 Rubber, vulcanized or thermoplastic—Determination of adhesion to textile fabrics
  • ISO 37:2011 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
  • ISO 41:1980 Shipbuilding—Inland vessels—Covers for deck openings for pumps [withdrawn without replacement]
  • ISO 43:2016 Aircraft—Jacking pads
  • ISO 44:1975 Aerospace—Lever-operated, two-position, ON/OFF switches—Directions of operation
  • ISO 45:1990 Aircraft—Pressure refuelling connections
  • ISO 46:1973 Aircraft—Fuel nozzle grounding plugs and sockets
  • ISO 48:2010 Rubber, vulcanized or thermoplastic—Determination of hardness (hardness between 10 IRHD and 100 IRHD)
  • ISO 49:1994 Malleable cast iron fittings threaded to ISO 7-1
  • ISO 50:1977 Metal pipes—Steel sockets screwed according to ISO 7 [Withdrawn without replacement]
  • ISO 53:1998 Cylindrical gears for general and heavy engineering—Standard basic rack tooth profile
  • ISO 54:1996 Cylindrical gears for general engineering and for heavy engineering—Modules
  • ISO 55:1977 Seedlac—Specification [Withdrawn without replacement]
  • ISO 57:1975 Bleached lac—Specification [Withdrawn without replacement]
  • ISO 60:1977 Plastics—Determination of apparent density of material that can be poured from a specified funnel
  • ISO 61:1976 Plastics—Determination of apparent density of moulding material that cannot be poured from a specified funnel
  • ISO 62:2008 Plastics—Determination of water absorption
  • ISO 63:1975 Flat transmission belts—Lengths [Withdrawn: Replaced with ISO 22]
  • ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1
  • ISO 67:1981 Muscovite mica blocks, thins and films—Grading by size [Withdrawn without replacement]
  • ISO 68 ISO general-purpose screw threads – Basic profile
    • ISO 68-1:1998 Part 1: Metric screw threads
    • ISO 68-2:1998 Part 2: Inch screw threads
  • ISO 69:1998 Cinematography—16 mm motion-picture and magnetic film—Cutting and perforating dimensions
  • ISO 70:1981 Cinematography—35 mm negative photographic sound record on 35 mm motion-picture film—Position and maximum width dimensions
  • ISO 71:2014 Cinematography—16 mm negative photographic sound record on 16 mm, 35/16 mm and 35/32 mm motion-picture film—Positions and dimensions
  • ISO 74:1976 Cinematography—Image area produced by camera aperture and maximum projectable image area on 8 mm Type R motion-picture film—Positions and dimensions
  • ISO 75 Plastics—Determination of temperature of deflection under load
    • ISO 75-1:2013 Part 1: General test method
    • ISO 75-2:2013 Part 2: Plastics and ebonite
    • ISO 75-3:2004 Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
  • ISO 76:2006 Rolling bearings—Static load ratings
  • ISO 78 Chemistry — Layouts for standards[Note 3]
    • ISO 78-2:1999 Part 2: Methods of chemical analysis
    • ISO 78-3:1983 Part 3: Standard for molecular absorption spectrometry [Withdrawn without replacement]
    • ISO 78-4:1983 Part 4: Standard for atomic absorption spectrometric analysis [Withdrawn without replacement]
  • ISO/TR 79:2015 Reference materials - Examples of reference materials for qualitative properties
  • ISO 82:1974 Steel—Tensile testing [Withdrawn: replaced with ISO 6892-1]
  • ISO 83:1976 Steel—Charpy impact test (U-notch) [Withdrawn: replaced with ISO 148-1]
  • ISO 86:1974 Steel—Tensile testing of sheet and strip less than 3 mm and not less than 0,5 mm thick [Withdrawn: replaced with ISO 6892-1]
  • ISO 89:1974 Steel—Tensile testing of wire [Withdrawn: replaced with ISO 6892-1]
  • ISO 90 Light gauge metal containers—Definitions and determination of dimensions and capacities
    • ISO 90-1:1997 Part 1: Open-top cans
    • ISO 90-2:1997 Part 2: General use containers
    • ISO 90-3:2000 Part 3: Aerosol cans
  • ISO 91 Petroleum measurement tables [Withdrawn: replaced with ISO 91:2017]
    • ISO 91-1:1992 Part 1: Tables based on reference temperatures of 15 degrees C and 60 degrees F
    • ISO 91-2:1991 Part 2: Tables based on a reference temperature of 20 degrees C
  • ISO 91:2017 Petroleum and related products - Temperature and pressure volume correction factors (petroleum measurement tables) and standard reference conditions
  • ISO 92:1976 Textile machinery and accessories—Spinning machinery—Definition of side (left or right)
  • ISO 93 Textile machinery and accessories—Cylindrical sliver cans
    • ISO 93-1:2006 Part 1: Main dimensions
    • ISO 93-2:2006 Part 2: Spring bottoms
  • ISO 94:1982 Textile machinery and accessories—Spindle gauges for ring-spinning and ring-doubling frames
  • ISO 96 Textile machinery and accessories—Rings and travellers for ring spinning and ring twisting frames
    • ISO 96-1:2016 Part 1: Flange rings T and SF and their travellers
    • ISO 96-2:2009 Part 2: HZ- and J-rings and their travellers
  • ISO 97:1975 Textile machinery and accessories—Rings for spinning, doubling and twisting for ear-shaped travellers [Withdrawn: replaced with ISO 96-2]
  • ISO 98:2001 Textile machinery and accessories—Spinning preparatory and spinning machinery—Main dimensions of coverings for top rollers

ISO 100 – ISO 199[edit]

  • ISO 100:1984 Pulleys for flat transmission belts—Crowns [Withdrawn: replaced with ISO 22]
  • ISO 102:1990 Aircraft—Gravity filling orifices
  • ISO 104:2015 Rolling bearings—Thrust bearings—Boundary dimensions, general plan
  • ISO 105 Textiles — Tests for colour fastness
    • ISO 105-A01:2010 Part A01: General principles of testing
    • ISO 105-A02:1993 Part A02: Grey scale for assessing change in colour
    • ISO 105-A03:1993 Part A03: Grey scale for assessing staining
    • ISO 105-A04:1989 Part A04: Method for the instrumental assessment of the degree of staining of adjacent fabrics
    • ISO 105-A05:1996 Part A05: Instrumental assessment of change in colour for determination of grey scale rating
    • ISO 105-A06:1995 Part A06: Instrumental determination of 1/1 standard depth of colour
    • ISO 105-A08:2001 Part A08: Vocabulary used in colour measurement
    • ISO 105-A11:2012 Part A11: Determination of colour fastness grades by digital imaging techniques
    • ISO 105-B01:2014 Part B01: Colour fastness to light: Daylight
    • ISO 105-B02:2014 Part B02: Colour fastness to artificial light: Xenon arc fading lamp test
    • ISO 105-B03:1994 Part B03: Colour fastness to weathering: Outdoor exposure
    • ISO 105-B04:1994 Part B04: Colour fastness to artificial weathering: Xenon arc fading lamp test
    • ISO 105-B05:1993 Part B05: Detection and assessment of photochromism
    • ISO 105-B06:1998 Part B06: Colour fastness and ageing to artificial light at high temperatures: Xenon arc fading lamp test
    • ISO 105-B07:2009 Part B07: Colour fastness to light of textiles wetted with artificial perspiration
    • ISO 105-B08:1995 Part B08: Quality control of blue wool reference materials 1 to 7
    • ISO 105-B10:2011 Part B10: Artificial weathering—Exposure to filtered xenon-arc radiation
    • ISO 105-C06:2010 Part C06: Colour fastness to domestic and commercial laundering
    • ISO 105-C07:1999 Part C07: Colour fastness to wet scrubbing of pigment printed textiles
    • ISO 105-C08:2010 Part C08: Colour fastness to domestic and commercial laundering using a non-phosphate reference detergent incorporating a low-temperature bleach activator
    • ISO 105-C09:2001 Part C09: Colour fastness to domestic and commercial laundering—Oxidative bleach response using a non-phosphate reference detergent incorporating a low temperature bleach activator
    • ISO 105-C10:2006 Part C10: Colour fastness to washing with soap or soap and soda
    • ISO 105-C12:2004 Part C12: Colour fastness to industrial laundering
    • ISO 105-D01:2010 Part D01: Colour fastness to drycleaning using perchloroethylene solvent
    • ISO 105-D02:2016 Part D02: Colour fastness to rubbing: Organic solvents
    • ISO 105-E01:2013 Part E01: Colour fastness to water
    • ISO 105-E02:2013 Part E02: Colour fastness to sea water
    • ISO 105-E03:2010 Part E03: Colour fastness to chlorinated water (swimming-pool water)
    • ISO 105-E04:2013 Part E04: Colour fastness to perspiration
    • ISO 105-E05:2010 Part E05: Colour fastness to spotting: Acid
    • ISO 105-E06:2006 Part E06: Colour fastness to spotting: Alkali
    • ISO 105-E07:2010 Part E07: Colour fastness to spotting: Water
    • ISO 105-E08:1994 Part E08: Colour fastness to hot water
    • ISO 105-E09:2010 Part E09: Colour fastness to potting
    • ISO 105-E10:1994 Part E10: Colour fastness to decatizing
    • ISO 105-E11:1994 Part E11: Colour fastness to steaming
    • ISO 105-E12:2010 Part E12: Colour fastness to milling: Alkaline milling
    • ISO 105-E13:1994 Part E13: Colour fastness to acid-felting: Severe
    • ISO 105-E14:1994 Part E14: Colour fastness to acid-felting: Mild
    • ISO 105-E16:2006 Part E16: Colour fastness to water spotting on upholstery fabrics
    • ISO 105-F01:2001 Part F01: Specification for wool adjacent fabric
    • ISO 105-F02:2009 Part F02: Specification for cotton and viscose adjacent fabrics
    • ISO 105-F03:2001 Part F03: Specification for polyamide adjacent fabric
    • ISO 105-F04:2001 Part F04: Specification for polyester adjacent fabric
    • ISO 105-F05:2001 Part F05: Specification for acrylic adjacent fabric
    • ISO 105-F06:2000 Part F06: Specification for silk adjacent fabric
    • ISO 105-F07:2001 Part F07: Specification for secondary acetate adjacent fabric
    • ISO 105-F09:2009 Part F09: Specification for cotton rubbing cloth
    • ISO 105-F10:1989 Part F10: Specification for adjacent fabric: Multifibre
    • ISO 105-G01:2016 Part G01: Colour fastness to nitrogen oxides
    • ISO 105-G02:1993 Part G02: Colour fastness to burnt-gas fumes
    • ISO 105-G03:1993 Part G03: Colour fastness to ozone in the atmosphere
    • ISO 105-G04:2016 Part G04: Colour fastness to oxides of nitrogen in the atmosphere at high humidities
    • ISO 105-J01:1997 Part J01: General principles for measurement of surface colour
    • ISO 105-J02:1997 Part J02: Instrumental assessment of relative whiteness
    • ISO 105-J03:2009 Part J03: Calculation of colour differences
    • ISO 105-J05:2007 Part J05: Method for the instrumental assessment of the colour inconstancy of a specimen with change in illuminant (CMCCON02)
    • ISO 105-N01:1993 Part N01: Colour fastness to bleaching: Hypochlorite
    • ISO 105-N02:1993 Part N02: Colour fastness to bleaching: Peroxide
    • ISO 105-N03:1993 Part N03: Colour fastness to bleaching: Sodium chlorite (mild)
    • ISO 105-N04:1993 Part N04: Colour fastness to bleaching: Sodium chlorite (severe)
    • ISO 105-N05:1993 Part N05: Colour fastness to stoving
    • ISO 105-P01:1993 Part P01: Colour fastness to dry heat (excluding pressing)
    • ISO 105-P02:2002 Part P02: Colour fastness to pleating: Steam pleating
    • ISO 105-S01:1993 Part S01: Colour fastness to vulcanization: Hot air
    • ISO 105-S02:1993 Part S02: Colour fastness to vulcanization: Sulfur monochloride
    • ISO 105-S03:1993 Part S03: Colour fastness to vulcanization: Open steam
    • ISO 105-X01:1993 Part X01: Colour fastness to carbonizing: Aluminium chloride
    • ISO 105-X02:1993 Part X02: Colour fastness to carbonizing: Sulfuric acid
    • ISO 105-X04:1994 Part X04: Colour fastness to mercerizing
    • ISO 105-X05:1994 Part X05: Colour fastness to organic solvents
    • ISO 105-X06:1994 Part X06: Colour fastness to soda boiling
    • ISO 105-X07:1994 Part X07: Colour fastness to cross-dyeing: Wool
    • ISO 105-X08:1994 Part X08: Colour fastness to degumming
    • ISO 105-X09:1993 Part X09: Colour fastness to formaldehyde
    • ISO 105-X10:1993 Part X10: Assessment of migration of textile colours into polyvinyl chloride coatings
    • ISO 105-X11:1994 Part X11: Colour fastness to hot pressing
    • ISO 105-X12:2016 Part X12: Colour fastness to rubbing
    • ISO 105-X13:1994 Part X13: Colour fastness of wool dyes to processes using chemical means for creasing, pleating and setting
    • ISO 105-X14:1994 Part X14: Colour fastness to acid chlorination of wool: Sodium dichloroisocyanurate
    • ISO 105-X16:2016 Part X16: Colour fastness to rubbing—Small areas
    • ISO 105-X18:2007 Part X18: Assessment of the potential to phenolic yellowing of materials
    • ISO 105-Z01:1993 Part Z01: Colour fastness to metals in the dye-bath: Chromium salts
    • ISO 105-Z02:1993 Part Z02: Colour fastness to metals in the dye-bath: Iron and copper
    • ISO 105-Z03:1996 Part Z03: Intercompatibility of basic dyes for acrylic fibres
    • ISO 105-Z04:1995 Part Z04: Dispersibility of disperse dyes
    • ISO 105-Z05:1996 Part Z05: Determination of the dusting behaviour of dyes
    • ISO 105-Z06:1998 Part Z06: Evaluation of dye and pigment migration
    • ISO 105-Z07:1995 Part Z07: Determination of application solubility and solution stability of water-soluble dyes
    • ISO 105-Z08:1995 Part Z08: Determination of solubility and solution stability of reactive dyes in the presence of electrolytes
    • ISO 105-Z09:1995 Part Z09: Determination of cold water solubility of water-soluble dyes
    • ISO 105-Z10:1997 Part Z10: Determination of relative colour strength of dyes in solution
    • ISO 105-Z11:1998 Part Z11: Evaluation of speckiness of colorant dispersions
  • ISO 108:1976 Textile machinery and accessories—Weaving looms—Definition of left and right sides
  • ISO 109:1982 Textile machinery—Working widths of weaving machines
  • ISO 110:1978 Textile machinery and accessories—Cones for yarn winding (cross wound) – Half angle of the cone 9 degrees 15' [Withdrawn without replacement]
  • ISO 111:1978 Textile machinery and accessories—Cones for yarn winding (cross wound) – Half angle of the cone 4 degrees 20' [Withdrawn: Replaced with ISO 8489-3]
  • ISO 112:1983 Textile machinery and accessories—Cones for yarn winding (cross wound) – Half angle of the cone 3 degrees 30' [Withdrawn: Replaced with ISO 8489-2]
  • ISO 113:2010 Rolling bearings—Plummer block housings—Boundary dimensions
  • ISO 114:1980 99.8 Unalloyed magnesium ingots—Chemical composition [Withdrawn: Replaced by ISO 8287]
  • ISO 115:2003 Unalloyed aluminium ingots for remelting—Classification and composition
  • ISO 119:1977 Plastics—Phenol-formaldehyde mouldings—Determination of free phenols—Iodometric method
  • ISO 120:1977 Plastics—Phenol-formaldehyde mouldings—Determination of free ammonia and ammonium compounds—Colorimetric comparison method
  • ISO 121:1980 Magnesium-aluminium-zinc alloy ingots and alloy castings—Chemical composition and mechanical properties of sand cast reference test bars [Withdrawn: replaced by ISO 16220]
  • ISO 123:2001 Rubber latex—Sampling
  • ISO 124:2014 Latex, rubber—Determination of total solids content
  • ISO 125:2011 Natural rubber latex concentrate—Determination of alkalinity
  • ISO 126:2005 Natural rubber latex concentrate—Determination of dry rubber content
  • ISO 127:2012 Rubber, natural latex concentrate—Determination of KOH number
  • ISO 128 Technical product documentation (TPD)—General principles of presentation[Note 3]
  • ISO 129 Technical product documentation (TPD)—Indication of dimensions and tolerances[Note 3]
    • ISO 129-1:2004 Part 1: General principles
    • ISO 129-4:2013 Part 4: Dimensioning of shipbuilding drawings
  • ISO 131:1979 Acoustics—Expression of physical and subjective magnitudes of sound or noise in air [Withdrawn without replacement]
  • ISO 132:2017 Rubber, vulcanized or thermoplastic—Determination of flex cracking and crack growth (De Mattia)
  • ISO 133:1983 Rubber, vulcanized—Determination of crack growth (De Mattia) [Withdrawn: Replaced with ISO 132]
  • ISO 136:1972 Steel—Simple torsion testing of wire [Withdrawn replaced by ISO 7800]
  • ISO 137:2015 Wool—Determination of fibre diameter—Projection microscope method
  • ISO 139:2005 Textiles—Standard atmospheres for conditioning and testing
  • ISO 140 Acoustics—Measurement of sound insulation in buildings and of building elements
    • ISO 140-2:1991 Part 2: Determination, verification and application of precision data [Withdrawn: replaced by ISO 12999-1:2014]
    • ISO 140-4:1998 Part 4: Field measurements of airborne sound insulation between rooms [Withdrawn: replaced by ISO 16283-1:2014]
    • ISO 140-5:1998 Part 5: Field measurements of airborne sound insulation of façade elements and façades [Withdrawn: replaced by ISO 16283-1:2014]
    • ISO 140-7:1998 Part 7: Field measurements of impact sound insulation of floors [Withdrawn: replaced by ISO 16283-1:2014]
    • ISO 140-14:2004 Part 14: Guidelines for special situations in the field [Withdrawn: replaced by ISO 16283-1:2014]
      • ISO 140-14:2004/Cor 1:2007
    • ISO 140-18:2006 Part 18: Laboratory measurement of sound generated by rainfall on building elements [Withdrawn: replaced by ISO 10140-1:2016]
  • ISO 141:1976 Textile machinery and accessories—Pirn winders and cross winders—Definition of left and right sides
  • ISO 142:1976 Textile machinery and accessories—Weaving preparatory machines—Definition of left and right sides
  • ISO 143:1977 Textile machinery and accessories—Weft pirns for automatic looms [Withdrawn without replacement]
  • ISO 144:1973 Steel—Reverse bend testing of wire [Withdrawn: replaced with ISO 7801]
  • ISO 146:1984 Metallic materials—Hardness test—Verification of Vickers hardness testing machines HV 0,2 to HV 100 [Withdrawn replaced with ISO 6507-2]
    • ISO 146-2:1993 Metallic materials—Verification of Vickers hardness testing machines—Part 2: Less than HV 0,2 [Withdrawn replaced with ISO 6507-2]
  • ISO 148 Metallic materials—Charpy pendulum impact test
    • ISO 148-1:2016 Part 1: Test method
    • ISO 148-2:2016 Part 2: Verification of testing machines
    • ISO 148-3:2016 Part 3: Preparation and characterization of Charpy V-notch test pieces for indirect verification of pendulum impact machines
  • ISO 150:2006 Raw, refined and boiled linseed oil for paints and varnishes—Specifications and methods of test
  • ISO 155:1998 Belt drives—Pulleys—Limiting values for adjustment of centres
  • ISO 156:1982 Metallic materials—Hardness test—Verification of Brinell hardness testing machines [Withdrawn replaced by ISO 6506-2]
  • ISO 157:1996 Coal—Determination of forms of sulfur
  • ISO 160:1980 Asbestos-cement pressure pipes and joints [Withdrawn without replacement]
  • ISO 161 Thermoplastics pipes for the conveyance of fluids—Nominal outside diameters and nominal pressures
    • ISO 161-1:1996 Part 1: Metric series
    • ISO 161-2:1996 Part 2: Inch-based series
  • ISO 162:1985 Cinematography—Head gaps and sound records for three-, four-, or six-track magnetic sound records on 35 mm and single-track on 17,5 mm motion-picture film containing no picture—Positions and width dimensions
  • ISO 171:1980 Plastics—Determination of bulk factor of moulding materials
  • ISO 172:1978 Plastics—Phenol-formaldehyde mouldings—Detection of free ammonia
  • ISO 174:1974 Plastics—Homopolymer and copolymer resins of vinyl chloride—Determination of viscosity number in dilute solution [Withdrawn replaced by ISO 1628-2]
  • ISO 175:2010 Plastics—Methods of test for the determination of the effects of immersion in liquid chemicals
  • ISO 176:2005 Plastics—Determination of loss of plasticizers—Activated carbon method
  • ISO 177:2016 Plastics—Determination of migration of plasticizers
  • ISO 178:2010 Plastics—Determination of flexural properties
  • ISO 179 Plastics—Determination of Charpy impact properties
    • ISO 179-1:2010 Part 1: Non-instrumented impact test
    • ISO 179-2:1997 Part 2: Instrumented impact test
  • ISO 180:2000 Plastics—Determination of Izod impact strength
  • ISO 182 Plastics—Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures
    • ISO 182-1:1990 Part 1: Congo red method
    • ISO 182-2:1990 Part 2: pH method
    • ISO 182-3:1993 Part 3: Conductometric method
    • ISO 182-4:1993 Part 4: Potentiometric method
  • ISO 185:2005 Grey cast irons - Classification
  • ISO 186:2002 Paper and board - Sampling to determine average quality
  • ISO 187:1990 Paper, board and pulps - Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples
  • ISO 188:2011 Rubber, vulcanized or thermoplastic - Accelerated ageing and heat resistance tests
  • ISO 196:1978 Wrought copper and copper alloys - Detection of residual stress - Mercury(I) nitrate test
  • ISO 197 Copper and copper alloys - Terms and definitions
    • ISO 197-1:1983 Part 1: Materials
    • ISO 197-2:1983 Part 2: Unwrought products (Refinery shapes)
    • ISO 197-3:1983 Part 3: Wrought products
    • ISO 197-4:1983 Part 4: Castings
    • ISO 197-5:1980 Part 5: Methods of processing and treatment
  • ISO 199:2014 Rolling bearings - Thrust bearings - Geometrical product specification (GPS) and tolerance values

ISO 200 – ISO 999[edit]

  • ISO 204:2009 Metallic materials - Uniaxial creep testing in tension - Method of test
  • ISO 209:2007 Aluminium and aluminium alloys - Chemical composition
  • ISO/TS 211:2014 Essential oils - General rules for labelling and marking of containers
  • ISO 212:2007 Essential oils - Sampling
  • ISO 214:1976 Documentation - Abstracts for publications and documentation
  • ISO 215:1986 Documentation - Presentation of contributions to periodicals and other serials
  • ISO 216:2007 Writing paper and certain classes of printed matter – Trimmed sizes – A and B series, and indication of machine direction
  • ISO 217:2013 Paper - Untrimmed sizes - Designation and tolerances for primary and supplementary ranges, and indication of machine direction
  • ISO 225:2010 Fasteners - Bolts, screws, studs and nuts - Symbols and descriptions of dimensions
  • ISO 226:2003 Acoustics – Normal equal-loudness-level contours
  • ISO 228 Pipe threads where pressure-tight joints are not made on the threads
  • ISO 229:1973 Machine tools - Speeds and feeds
  • ISO 230 Test code for machine tools
    • ISO 230-1:2012 Part 1: Geometric accuracy of machines operating under no-load or quasi-static conditions
    • ISO 230-2:2014 Part 2: Determination of accuracy and repeatability of positioning of numerically controlled axes
    • ISO 230-3:2007 Part 3: Determination of thermal effects
    • ISO 230-4:2005 Part 4: Circular tests for numerically controlled machine tools
    • ISO 230-5:2000 Part 5: Determination of the noise emission
    • ISO 230-6:2002 Part 6: Determination of positioning accuracy on body and face diagonals (Diagonal displacement tests)
    • ISO 230-7:2015 Part 7: Geometric accuracy of axes of rotation
    • ISO/TR 230-8:2010 Part 8: Vibrations
    • ISO/TR 230-9:2005 Part 9: Estimation of measurement uncertainty for machine tool tests according to series ISO 230, basic equations
    • ISO 230-10:2016 Part 10: Determination of the measuring performance of probing systems of numerically controlled machine tools
  • ISO 233 Information and documentation – Transliteration of Arabic characters into Latin characters[Note 3]
  • ISO 234 Files and rasps
    • ISO 234-1:1983 Part 1: Dimensions
    • ISO 234-2:1982 Part 2: Characteristics of cut
  • ISO 235:2016 Parallel shank jobber and stub series drills and Morse taper shank drills
  • ISO 236 Reamers[Note 3]
    • ISO 236-1:1976 Hand reamers
    • ISO 236-2:2013 Part 2: Long fluted machine reamers with Morse taper shanks
  • ISO 237:1975 Rotating tools with parallel shanks - Diameters of shanks and sizes of driving squares
  • ISO 238:2016 Reduction sleeves and extension sockets for tools with Morse taper shanks
  • ISO 239:1999 Drill chuck tapers
  • ISO 240:2016 Milling cutters - Interchangeability dimensions for cutter arbors or cutter mandrels
  • ISO 241:1994 Shanks for turning and planing tools - Shapes and dimensions of the section
  • ISO 242:2014 Carbide tips for brazing on turning tools
  • ISO 243:2014 Turning tools with carbide tips - External tools
  • ISO 244:1979 Aircraft - Sealing wire
  • ISO 245:1998 Aerospace - Lockwire - Diameters
  • ISO 246:2007 Rolling bearings - Cylindrical roller bearings, separate thrust collars - Boundary dimensions
  • ISO 247:2006 Rubber - Determination of ash
  • ISO 248 Rubber, raw - Determination of volatile-matter content
    • ISO 248-1:2011 Part 1: Hot-mill method and oven method
    • ISO 248-2:2012 Part 2: Thermogravimetric methods using an automatic analyser with an infrared drying unit
  • ISO 249:2016 Rubber, raw natural - Determination of dirt content
  • ISO 251:2012 Conveyor belts with textile carcass - Widths and lengths
  • ISO 252:2007 Conveyor belts - Adhesion between constitutive elements - Test methods
  • ISO 254:2011 Belt drives - Pulleys - Quality, finish and balance
  • ISO 255:1990 Belt drives - Pulleys for V-belts (system based on datum width) - Geometrical inspection of grooves
  • ISO 257:2004 Pesticides and other agrochemicals - Principles for the selection of common names
  • ISO 259 Information and documentation – Transliteration of Hebrew characters into Latin characters[Note 3]
  • ISO 261:1998 ISO general purpose metric screw threads – General plan
  • ISO 262:1998 ISO general purpose metric screw threads – Selected sizes for screws, bolts and nuts
  • ISO 263:1973 ISO inch screw threads - General plan and selection for screws, bolts and nuts - Diameter range 0,06 to 6 in
  • ISO 265 Pipes and fittings of plastics materials - Fittings for domestic and industrial waste pipes - Basic dimensions: Metric series
    • ISO 265-1:1988 Part 1: Unplasticized poly(vinyl chloride) (PVC-U)
  • ISO 266:1997 Acoustics - Preferred frequencies
  • ISO 268:1980 Aircraft - Mechanical and electromechanical indicators - General requirements
  • ISO 269:1985 Correspondence envelopes - Designation and sizes [Withdrawn without replacement]
  • ISO 272:1982 Fasteners - Hexagon products - Widths across flats
  • ISO 273:1979 Fasteners - Clearance holes for bolts and screws
  • ISO 276:2002 Binders for paints and varnishes - Linseed stand oil - Requirements and methods of test
  • ISO 277:2002 Binders for paints and varnishes - Raw tung oil - Requirements and methods of test
  • ISO 279:1998 Essential oils - Determination of relative density at 20 degrees C - Reference method
  • ISO 280:1998 Essential oils - Determination of refractive index
  • ISO 281:2007 Rolling bearings - Dynamic load ratings and rating life
  • ISO 282:1992 Conveyor belts - Sampling
  • ISO 283:2015 Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method
  • ISO 284:2012 Conveyor belts - Electrical conductivity - Specification and test method
  • ISO 286 Geometrical product specifications (GPS) – ISO code system for tolerances on linear sizes
    • ISO 286-1:2010 Part 1: Basis of tolerances, deviations and fits
    • ISO 286-2:2010 Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
  • ISO 287:2009 Paper and board - Determination of moisture content of a lot - Oven-drying method
  • ISO 289 Rubber, unvulcanized - Determinations using a shearing-disc viscometer
    • ISO 289-1:2015 Part 1: Determination of Mooney viscosity
    • ISO 289-2:2016 Part 2: Determination of pre-vulcanization characteristics
    • ISO 289-3:2015 Part 3: Determination of the Delta Mooney value for non-pigmented, oil-extended emulsion-polymerized SBR
    • ISO 289-4:2003 Part 4: Determination of the Mooney stress-relaxation rate
  • ISO 291:2008 Plastics - Standard atmospheres for conditioning and testing
  • ISO 293:2004 Plastics - Compression moulding of test specimens of thermoplastic materials
  • ISO 294 Plastics - Injection moulding of test specimens of thermoplastic materials
    • ISO 294-1:2017 Part 1: General principles, and moulding of multipurpose and bar test specimens
    • ISO 294-2:1996 Part 2: Small tensile bars
    • ISO 294-3:2002 Part 3: Small plates
    • ISO 294-4:2001 Part 4: Determination of moulding shrinkage
    • ISO 294-5:2011 Part 5: Preparation of standard specimens for investigating anisotropy
  • ISO 295:2004 Plastics - Compression moulding of test specimens of thermosetting materials
  • ISO 296:1991 Machine tools - Self-holding tapers for tool shanks
  • ISO 297:1988 7/24 tapers for tool shanks for manual changing
  • ISO 298:1973 Machine tools - Lathe centres - Sizes for interchangeability
  • ISO 299:1987 Machine tool tables - T-slots and corresponding bolts
  • ISO 302:2015 Pulps - Determination of Kappa number
  • ISO 306:2013 Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST)
  • ISO 361:1975 Basic ionizing radiation symbol
  • ISO 362 Measurement of noise emitted by accelerating road vehicles – Engineering method
    • ISO 362-1:2015 Part 1: M and N categories
    • ISO 362-2:2009 Part 2: L category
    • ISO 362-3:2016 Part 3: Indoor testing M and N categories
  • ISO 369:2009 Machine tools - Symbols for indications appearing on machine tools
  • ISO 374 Protective gloves against dangerous chemicals and micro-organisms
    • ISO 374-1:2016 Part 1: Terminology and performance requirements for chemical risks
    • ISO 374-5:2016 Part 5: Terminology and performance requirements for micro-organisms risks
  • ISO 384:2015 Laboratory glass and plastics ware – Principles of design and construction of volumetric instruments
  • ISO 385:2005 Laboratory glassware – Burettes
  • ISO 386:1977 Liquid-in-glass laboratory thermometers – Principles of design, construction and use
  • ISO 387:1977 Hydrometers – Principles of construction and adjustment
  • ISO 407:2004 Small medical gas cylinders – Pin-index yoke-type valve connections
  • ISO 428:1983 Wrought copper-aluminium alloys - Chemical composition and forms of wrought products [Withdrawn without replacement]
  • ISO 445:2013 Pallets for materials handling – Vocabulary
  • ISO 463:2006 Geometrical Product Specifications (GPS) – Dimensional measuring equipment – Design and metrological characteristics of mechanical dial gauges
  • ISO 472:2013 Plastics – Vocabulary
  • ISO 476:1982 Textile machinery and accessories – Pirn winding machines – Vocabulary
  • ISO 477:1982 Textile machinery and accessories – Cone and cheese winding machines – Vocabulary
  • ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
  • ISO 500 Agricultural tractors – Rear-mounted power take-off types 1, 2 and 3
  • ISO 518:2006 Photography – Camera accessory shoes, with and without electrical contacts, for photoflash lamps and electronic photoflash units – Specification
  • ISO 519:1992 Photography – Hand-held cameras – Flash-connector dimensions
  • ISO 532 Acoustics – Methods for calculating loudness
    • ISO 532-1:2017 Part 1: Zwicker method
    • ISO 532-2:2017 Part 2: Moore-Glasberg method
  • ISO 536:2012 Paper and board – Determination of grammage
  • ISO 561:1989 Coal preparation plant - Graphical symbols
  • ISO/TR 581:2005 Weldability - Metallic materials - General principles
  • ISO 611:2003 Road vehicles – Braking of automotive vehicles and their trailers – Vocabulary
  • ISO 612:1978 Road vehicles – Dimensions of motor vehicles and towed vehicles – Terms and definitions
  • ISO 633:2007 Cork – Vocabulary
  • ISO 639 Codes for the representation of names of languages
    • ISO 639-1:2002 Part 1: Alpha-2 code
    • ISO 639-2:1998 Part 2: Alpha-3 code
    • ISO 639-3:2007 Part 3: Alpha-3 code for comprehensive coverage of languages
    • ISO 639-4:2010 Part 4: General principles of coding of the representation of names of languages and related entities, and application guidelines
    • ISO 639-5:2008 Part 5: Alpha-3 code for language families and groups
    • ISO 639-6:2009 Part 6: Alpha-4 code for comprehensive coverage of language variants [Withdrawn, no replacement]
  • ISO/IEC 646:1991 Information technology – ISO 7-bit coded character set for information interchange
  • ISO 648:2008 Laboratory glassware – Single-volume pipettes
  • ISO 649 Laboratory glassware – Density hydrometers for general purposes
    • ISO 649-1:1981 Part 1: Specification
    • ISO 649-2:1981 Part 2: Test methods and use
  • ISO 650:1977 Relative density 60/60 degrees F hydrometers for general purposes
  • ISO 651:1975 Solid-stem calorimeter thermometers
  • ISO 652:1975 Enclosed-scale calorimeter thermometers
  • ISO 653:1980 Long solid-stem thermometers for precision use
  • ISO 654:1980 Short solid-stem thermometers for precision use
  • ISO 655:1980 Long enclosed-scale thermometers for precision use
  • ISO 656:1980 Short enclosed-scale thermometers for precision use
  • ISO 657 Hot-rolled steel sections
  • ISO 663:2017 Animal and vegetable fats and oils - Determination of insoluble impurities content
  • ISO 668 Series 1 freight containers – Classification, dimensions and ratings
  • ISO 676:1995 Spices and condiments – Botanical nomenclature
  • ISO 690:2010 Information and documentation – Guidelines for bibliographic references and citations to information resources
  • ISO 701:1998 International gear notation - Symbols for geometrical data
  • ISO 704:2009 Terminology work – Principles and methods
  • ISO 710 Graphical symbols for use on detailed maps, plans and geological cross-sections
    • ISO 710-1:1974 Part 1: General rules of representation
    • ISO 710-2:1974 Part 2: Representation of sedimentary rocks
    • ISO 710-3:1974 Part 3: Representation of magmatic rocks
    • ISO 710-4:1982 Part 4: Representation of metamorphic rocks
    • ISO 710-5:1989 Part 5: Representation of minerals
    • ISO 710-6:1984 Part 6: Representation of contact rocks and rocks which have undergone metasomatic, pneumatolytic or hydrothermal transformation or transformation by weathering
    • ISO 710-7:1984 Part 7: Tectonic symbols
  • ISO 732 Photography – 120-size and 220-size films – Dimensions
  • ISO 748:2007 Hydrometry – Measurement of liquid flow in open channels using current-meters or floats
  • ISO 760:1978 Determination of water - Karl Fischer method (General method)
  • ISO 764 Horology – Magnetic resistant watches
  • ISO 772:2011 Hydrometry - Vocabulary and symbols
  • ISO 780:2015 Packaging - Distribution packaging - Graphical symbols for handling and storage of packages
  • ISO 787 General methods of test for pigments and extenders
    • ISO 787-9:1981 Determination of pH value of an aqueous suspension
  • ISO 830:1999 Freight containers – Vocabulary
  • ISO 832:1994 Information and documentation - Bibliographic description and references - Rules for the abbreviation of bibliographic terms
  • ISO 835:2007 Laboratory glassware – Graduated pipettes
  • ISO 836:2001 Terminology for refractories
  • ISO 838:1974 Paper – Holes for general filing purposes – Specifications
  • ISO 843:1997 Information and documentation – Conversion of Greek characters into Latin characters
  • ISO 846:1997 Plastics – Evaluation of the action of microorganisms
  • ISO 857 Welding and allied processes - Vocabulary
    • ISO 857-2:2005 Part 2: Soldering and brazing processes and related terms
  • ISO 860:2007 Terminology work – Harmonization of concepts and terms
  • ISO 862:1984 Surface active agents – Vocabulary
  • ISO 898 Mechanical properties of fasteners made of carbon steel and alloy steel[Note 3]
  • ISO 928 Spices and condiments - Determination of total ash
  • ISO 936 Meat and meat products - Determination of total ash
  • ISO 962:1974 Information processing - Implementation of the 7- bit coded character set and its 7- bit and 8-bit extensions on 9- track 12,7 mm (0.5 in) magnetic tape
  • ISO 965 ISO general purpose metric screw threads – Tolerances
  • ISO 999:1996 Information and documentation – Guidelines for the content, organization, and presentation of indexes

ISO 1000 – ISO 4999[edit]

  • ISO 1000 SI units and recommendations for the use of their multiples and of certain other units [withdrawn 2009-11-17]
  • ISO/IEC 1001:2012 Information technology – File structure and labelling of magnetic tapes for information interchange
  • ISO 1004 Information processing – Magnetic ink character recognition – Print specifications
    • ISO 1004-1:2013 Part 1: Print specifications for E13B
    • ISO 1004-2:2013 Part 2: Print specifications for CMC7
  • ISO 1007 Photography – 135-size film and magazine – Specifications
  • ISO 1031:1974 Coniferous sawn timber – Defects – Terms and definitions
  • ISO 1032:1974 Coniferous sawn timber – Sizes – Terms and definitions
  • ISO 1034:1973 Aircraft - Ground air-conditioning connections
  • ISO 1042:1998 Laboratory glassware – One-mark volumetric flasks
  • ISO 1069:1973 Magnetic compasses and binnacles for sea navigation – Vocabulary
  • ISO 1070:1992 Liquid flow measurement in open channels – Slope-area method
  • ISO 1073 Alphanumeric character sets for optical recognition
    • ISO 1073-1:1976 Part 1: Character set OCR-A - Shapes and dimensions of the printed image
    • ISO 1073-2:1976 Part 2: Character set OCR-B - Shapes and dimensions of the printed image
  • ISO 1081:2013 Belt drives - V-belts and V-ribbed belts, and corresponding grooved pulleys - Vocabulary
  • ISO 1086:1991 Information and documentation – Title leaves of books
  • ISO 1087 Terminology work - Vocabulary
    • ISO 1087-1:2000 Part 1: Theory and application
  • ISO 1088:2007 Hydrometry – Velocity-area methods using current-meters – Collection and processing of data for determination of uncertainties in flow measurement
  • ISO 1101:2017 Geometrical product specifications (GPS) – Geometrical tolerancing – Tolerances of form, orientation, location and run-out
  • ISO 1100 Hydrometry – Measurement of liquid flow in open channels
    • ISO 1100-2:2010 Part 2: Determination of the stage-discharge relationship
  • ISO 1107:2017 Fishing nets – Netting – Basic terms and definitions
  • ISO 1112:2009 Horology – Functional and non-functional jewels
  • ISO 1113:1979 Information processing - Representation of the 7- bit coded character set on punched tape
  • ISO 1119:2011 Geometrical product specifications (GPS) - Series of conical tapers and taper angles
  • ISO 1122 Vocabulary of gear terms
    • ISO 1122-1:1998 Part 1: Definitions related to geometry
    • ISO 1122-2:1999 Part 2: Definitions related to worm gear geometry
  • ISO 1132 Rolling bearings - Tolerances
    • ISO 1132-1:2000 Part 1: Terms and definitions
  • ISO 1135 Transfusion equipment for medical use
    • ISO 1135-3:2016 Part 3: Blood-taking sets for single use
    • ISO 1135-4:2015 Part 4: Transfusion sets for single use, gravity feed
    • ISO 1135-5:2015 Part 5: Transfusion sets for single use with pressure infusion apparatus
  • ISO 1146:1988 Pyrometric reference cones for laboratory use – Specification
  • ISO 1151 Flight dynamics - Concepts, quantities and symbols
    • ISO 1151-1:1988 Part 1: Aircraft motion relative to the air
    • ISO 1151-2:1985 Part 2: Motions of the aircraft and the atmosphere relative to the Earth
    • ISO 1151-3:1989 Part 3: Derivatives of forces, moments and their coefficients
    • ISO 1151-4:1994 Part 4: Concepts and quantities used in the study of aircraft stability and control
    • ISO 1151-5:1987 Part 5: Quantities used in measurements
    • ISO 1151-6:1982 Part 6: Aircraft geometry
    • ISO 1151-7:1985 Part 7: Flight points and flight envelopes
    • ISO 1151-8:1992 Part 8: Concepts and quantities used in the study of the dynamic behaviour of the aircraft
    • ISO 1151-9:1993 Part 9: Models of atmospheric motions along the trajectory of the aircraft
  • ISO 1154:1975 Information processing – Punched paper tape – Dimensions and location of feed holes and code holes
  • ISO 1155:1978 Information processing – Use of longitudinal parity to detect errors in information messages
  • ISO 1176:1990 Road vehicles – Masses – Vocabulary and codes
  • ISO 1177:1985 Information processing – Character structure for start/stop and synchronous character oriented transmission
  • ISO 1182 Reaction to fire tests for products—Non-combustibility test
  • ISO 1213 Solid mineral fuels – Vocabulary
    • ISO 1213-1:1993 Part 1: Terms relating to coal preparation
    • ISO 1213-2:2016 Part 2: Terms relating to sampling, testing and analysis
  • ISO 1217 Displacement compressors—Acceptance tests
  • ISO 1219 Fluid power systems and components - Graphical symbols and circuit diagrams
    • ISO 1219-1:2012 Part 1: Graphical symbols for conventional use and data-processing applications
    • ISO 1219-2:2012 Part 2: Circuit diagrams
    • ISO 1219-3:2016 Part 3: Symbol modules and connected symbols in circuit diagrams
  • ISO 1222 Photography – Tripod connections
  • ISO 1268 Fibre-reinforced plastics – Methods of producing test plates
  • ISO 1302:2002 Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation
  • ISO 1382:2012 Rubber – Vocabulary
  • ISO 1402 Rubber and plastics hoses and hose assemblies - Hydrostatic testing
  • ISO 1413:2016 Horology - Shock-resistant wrist watches
  • ISO 1438:2017 Hydrometry – Open channel flow measurement using thin-plate weirs
  • ISO 1502:1996 ISO general-purpose metric screw threads – Gauges and gauging
  • ISO 1506:1982 Textile machinery – Dyeing, finishing and allied machinery – Classification and nomenclature
  • ISO 1531:1973 Fishing nets – Hanging of netting – Basic terms and definitions
  • ISO 1538:1984 Programming languages - ALGOL 60
  • ISO/IEC 1539 Information technology – Programming languages – Fortran
    • ISO/IEC 1539-1:2018 Part 1: Base language
    • ISO/IEC 1539-2:2000 Part 2: Varying length character strings
  • ISO 1586:1977 Textile machinery and accessories – Shuttles – Terms and designation in relation to the position of the shuttle eye
  • ISO 1629:2013 Rubber and latices – Nomenclature
  • ISO 1660:2017 Geometrical product specifications (GPS) - Geometrical tolerancing - Profile tolerancing
  • ISO 1663 Rigid cellular plastics – Determination of water vapour transmission properties
  • ISO 1680:2013 Acoustics – Test code for the measurement of airborne noise emitted by rotating electrical machines
  • ISO 1681:1973 Information processing – Unpunched paper cards – Specification
  • ISO 1683:2015 Acoustics - Preferred reference values for acoustical and vibratory levels
  • ISO 1703:2005 Assembly tools for screws and nuts - Designation and nomenclature
  • ISO 1730:1980 Dictation equipment – Basic operating requirements
  • ISO 1745:1975 Information processing – Basic mode control procedures for data communication systems
  • ISO 1750 Pesticides and other agrochemicals – Common names
  • ISO 1768:1975 Glass hydrometers – Conventional value for the thermal cubic expansion coefficient (for use in the preparation of measurement tables for liquids)
  • ISO 1769:1975 Laboratory glassware – Pipettes – Colour coding
  • ISO 1770:1981 Solid-stem general purpose thermometers
  • ISO 1771:1981 Enclosed-scale general purpose thermometers
  • ISO 1791:1983 Building construction – Modular co-ordination – Vocabulary
  • ISO 1803:1997 Building construction – Tolerances – Expression of dimensional accuracy – Principles and terminology
  • ISO 1804:1972 Doors – Terminology
  • ISO 1809:1977 Textile machinery and accessories – Types of formers for yarn packages – Nomenclature
  • ISO 1828:2012 Health informatics – Categorial structure for terminological systems of surgical procedures
  • ISO 1837:2003 Lifting hooks – Nomenclature
  • ISO 1858:1977 Information processing – General purpose hubs and reels, with 76 mm (3 in) centrehole, for magnetic tape used in interchange instrumentation applications
  • ISO 1859:1973 Information processing – Unrecorded magnetic tapes for interchange instrumentation applications – General dimensional requirements
  • ISO 1860:1986 Information processing – Precision reels for magnetic tape used in interchange instrumentation applications
  • ISO 1861:1975 Information processing – 7- track, 12,7 mm (0.5 in) wide magnetic tape for information interchange recorded at 8 rpmm (200 rpi)
  • ISO 1862:1975 Information processing – 9- track, 12,7 mm (0.5 in) wide magnetic tape for information interchange recorded at 8 rpmm (200 rpi)
  • ISO/IEC 1863:1990 Information processing – 9-track, 12,7 mm (0,5 in) wide magnetic tape for information interchange using NRZ1 at 32 ftpmm (800 ftpi) – 32 cpmm (800 cpi)
  • ISO/IEC 1864:1992 Information technology – Unrecorded 12,7 mm (0,5 in) wide magnetic tape for information interchange – 32 ftpmm (800 ftpi), NRZ1, 126 ftpmm (3 200 ftpi) phase encoded and 356 ftpmm (9 042 ftpi), NRZ1
  • ISO 1891:2009 Fasteners - Terminology
    • ISO 1891-2:2014 Part 2: Vocabulary and definitions for coatings
  • ISO 1928 Solid mineral fuels – Determination of gross calorific value by the bomb calorimetric method and calculation of net calorific value
  • ISO 1938 Geometrical product specifications (GPS) – Dimensional measuring equipment
    • ISO 1938-1:2015 Part 1: Plain limit gauges of linear size
    • ISO 1938-2:2017 Part 2: Reference disk gauges
  • ISO 1942:2009 Dentistry - Vocabulary
  • ISO 1951:2007 Presentation/representation of entries in dictionaries - Requirements, recommendations and information
  • ISO 1956 Fruits and vegetables – Morphological and structural terminology
    • ISO 1956-1:1982 (No part title)
    • ISO 1956-2:1989 (No part title)
  • ISO 1964:1987 Shipbuilding - Indication of details on the general arrangement plans of ships
  • ISO 1968:2004 Fibre ropes and cordage – Vocabulary
  • ISO/IEC 1989:2014 Information technology - Programming languages, their environments and system software interfaces - Programming language COBOL
  • ISO 1990 Fruits – Nomenclature
    • ISO 1990-1:1982 First list
    • ISO 1990-2:1985 Second list
  • ISO 1991 Vegetables – Nomenclature
    • ISO 1991-1:1982 First list
    • ISO 1991-2:1995 Part 2: Second list
  • ISO 1996 Acoustics – Description, measurement and assessment of environmental noise
    • ISO 1996-1:2016 Part 1: Basic quantities and assessment procedures[3]
    • ISO 1996-2:2017 Part 2: Determination of sound pressure levels
  • ISO 1998 Petroleum industry – Terminology
    • ISO 1998-1:1998 Part 1: Raw materials and products
    • ISO 1998-2:1998 Part 2: Properties and tests
    • ISO 1998-3:1998 Part 3: Exploration and production
    • ISO 1998-4:1998 Part 4: Refining
    • ISO 1998-5:1998 Part 5: Transport, storage, distribution
    • ISO 1998-6:2000 Part 6: Measurement
    • ISO 1998-7:1998 Part 7: Miscellaneous terms
    • ISO 1998-99:2000 Part 99: General and index
  • ISO 1999:2013 Acoustics - Estimation of noise-induced hearing loss[4]
  • ISO 2014:1976 Writing of calendar dates in all-numeric form [Withdrawn: replaced by ISO 8601:1988]
  • ISO 2015:1976 Numbering of weeks [Withdrawn: replaced by ISO 8601:1988]
  • ISO 2017 Mechanical vibration and shock – Resilient mounting systems
    • ISO 2017-1:2005 Part 1: Technical information to be exchanged for the application of isolation systems
    • ISO 2017-2:2007 Part 2: Technical information to be exchanged for the application of vibration isolation associated with railway systems
    • ISO 2017-3:2015 Part 3: Technical information to be exchanged for application of vibration isolation to new buildings
  • ISO/IEC 2022:1994 Information technology – Character code structure and extension techniques
  • ISO 2033:1983 Information processing - Coding of machine readable characters (MICR and OCR)
  • ISO 2041:2009 Mechanical vibration, shock and condition monitoring - Vocabulary
  • ISO 2047:1975 Information processing - Graphical representations for the control characters of the 7- bit coded character set
  • ISO 2074:2007 Plywood – Vocabulary
  • ISO 2076:2013 Textiles – Man-made fibres – Generic names
  • ISO 2080:2008 Metallic and other inorganic coatings - Surface treatment, metallic and other inorganic coatings - Vocabulary
  • ISO 2108:2005 Information and documentation – International standard book number (ISBN)
  • ISO 2110:1989 Information technology – Data communication – 25-pole DTE/DCE interface connector and contact number assignments
  • ISO 2145:1978 Documentation – Numbering of divisions and subdivisions in written documents
  • ISO 2146:2010 Information and documentation - Registry services for libraries and related organizations
  • ISO 2148:1974 Continuous handling equipment – Nomenclature
  • ISO 2151:2004 Acoustics – Noise test code for compressors and vacuum pumps – Engineering method (Grade 2)
  • ISO 2162 Technical product documentation – Springs
    • ISO 2162-1:1993 Part 1: Simplified representation
    • ISO 2162-2:1993 Part 2: Presentation of data for cylindrical helical compression springs
  • ISO 2171 Cereals, pulses and by-products – Determination of ash yield by incineration
  • ISO 2186:2007 Fluid flow in closed conduits – Connections for pressure signal transmissions between primary and secondary elements
  • ISO 2187:1990 Spinning preparatory machinery, spinning and doubling (twisting) machinery – List of equivalent terms
  • ISO 2203:1973 Technical drawings – Conventional representation of gears
  • ISO 2205:1975 Textile machinery and accessories – Drafting arrangements for spinning machines – Terminology
  • ISO 2240:2003 Photography – Colour reversal camera films – Determination of ISO speed
  • ISO 2257:1980 Office machines and printing machines used for information processing – Widths of fabric printing ribbons on spools
  • ISO 2258:1976 Printing ribbons – Minimum markings to appear on containers
  • ISO 2281:1990 Horology - Water-resistant watches [Withdrawn: replaced by ISO 22810:2010]
  • ISO 2300:1973 Sawn timber of broadleaved species – Defects – Terms and definitions
  • ISO 2331:1974 Fork lift trucks – Hook-on type fork arms – Vocabulary
  • ISO/IEC 2375:2003 Information technology - Procedure for registration of escape sequences and coded character sets
  • ISO/IEC 2382:2015 Information technology - Vocabulary
    • ISO/IEC 2382-36:2013 Part 36: Learning, education and training
    • ISO/IEC 2382-37:2017 Part 37: Biometrics
  • ISO 2384:1977 Documentation – Presentation of translations
  • ISO 2395:1990 Test sieves and test sieving - Vocabulary
  • ISO 2425:2010 Hydrometry – Measurement of liquid flow in open channels under tidal conditions
  • ISO 2444:1988 Joints in building – Vocabulary
  • ISO 2532:1974 Steel wire ropes - Vocabulary
  • ISO 2533:1975 Standard Atmosphere
  • ISO 2537:2007 Hydrometry – Rotating-element current-meters
  • ISO 2538 Geometrical product specifications (GPS) - Wedges
    • ISO 2538-1:2014 Part 1: Series of angles and slopes
    • ISO 2538-2:2014 Part 2: Dimensioning and tolerancing
  • ISO 2553:2013 Welding and allied processes – Symbolic representation on drawings – Welded joints
  • ISO 2574:1994 Aircraft – Electrical cables – Identification marking
  • ISO 2575:2010 Road vehicles - Symbols for controls, indicators and tell-tales
  • ISO/IEC 2593:2000 Information technology – Telecommunications and information exchange between systems – 34-pole DTE/DCE interface connector mateability dimensions and contact number assignments
  • ISO 2602:1980 Statistical interpretation of test results - Estimation of the mean - Confidence interval
  • ISO 2628:1973 Basic mode control procedures – Complements
  • ISO 2629:1973 Basic mode control procedures – Conversational information message transfer
  • ISO 2669:1995 Environmental tests for aircraft equipment - Steady-state acceleration
  • ISO 2671:1982 Environmental tests for aircraft equipment - Part 3.4 : Acoustic vibration
  • ISO 2685:1998 Aircraft - Environmental test procedure for airborne equipment - Resistance to fire in designated fire zones
  • ISO 2692:2014 Geometrical product specifications (GPS) – Geometrical tolerancing – Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
  • ISO 2709:2008 Information and documentation – Format for information exchange
  • ISO 2710 Reciprocating internal combustion engines - Vocabulary
    • ISO 2710-1:2000 Part 1: Terms for engine design and operation
    • ISO 2710-2:1999 Part 2: Terms for engine maintenance
  • ISO 2711:1973 Information processing interchange - Representation of ordinal dates [Withdrawn: replaced by ISO 8601:1988]
  • ISO 2768 General tolerances
    • ISO 2768-1:1989 Part 1: Tolerances for linear and angular dimensions without individual tolerance indications
    • ISO 2768-2:1989 Part 2: Geometrical tolerances for features without individual tolerance indications
  • ISO 2775:1977 Office machines and printing machines used for information processing – Widths of one-time paper or plastic printing ribbons and marking to indicate the end of the ribbons
  • ISO 2784:1974 Continuous forms used for information processing - Sizes and sprocket feed holes
  • ISO 2788:1986 Documentation - Guidelines for the establishment and development of monolingual thesauri [Withdrawn: replaced by ISO 25964-1:2011]
  • ISO 2789:2013 Information and documentation - International library statistics
  • ISO 2806:1994 Industrial automation systems - Numerical control of machines - Vocabulary
  • ISO 2822 Raw cattle hides and calf skins
    • ISO 2822-1:1998 Part 1: Descriptions of defects
  • ISO 2848:1984 Building construction - Modular coordination - Principles and rules
  • ISO 2852 Stainless steel clamp pipe couplings for the food industry
  • ISO 2854:1976 Statistical interpretation of data - Techniques of estimation and tests relating to means and variances
  • ISO 2859 Sampling procedures for inspection by attributes
    • ISO 2859-1:1999 Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
    • ISO 2859-2:1985 Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection
    • ISO 2859-3:2005 Part 3: Skip-lot sampling procedures
    • ISO 2859-4:2002 Part 4: Procedures for assessment of declared quality levels
    • ISO 2859-5:2005 Part 5: System of sequential sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection
    • ISO 2859-10:2006 Part 10: Introduction to the ISO 2859 series of standards for sampling for inspection by attributes
  • ISO 2922:2000 Acoustics – Measurement of airborne sound emitted by vessels on inland waterways and harbours
  • ISO 2923:1996 Acoustics - Measurement of noise on board vessels
  • ISO 2954:2012 Mechanical vibration of rotating and reciprocating machinery – Requirements for instruments for measuring vibration severity
  • ISO 2972:1979 Numerical control of machines - Symbols
  • ISO 2975 Measurement of water flow in closed conduits – Tracer methods
    • ISO 2975-1:1974 Part 1: General
    • ISO 2975-2:1975 Part 2: Constant rate injection method using non-radioactive tracers
    • ISO 2975-3:1976 Part 3: Constant rate injection method using radioactive tracers
    • ISO 2975-6:1977 Part 6: Transit time method using non-radioactive tracers
    • ISO 2975-7:1977 Part 7: Transit time method using radioactive tracers
  • ISO 3002 Basic quantities in cutting and grinding
    • ISO 3002-1:1982 Part 1: Geometry of the active part of cutting tools – General terms, reference systems, tool and working angles, chip breakers
    • ISO 3002-2:1982 Part 2: Geometry of the active part of cutting tools – General conversion formulae to relate tool and working angles
    • ISO 3002-3:1984 Part 3: Geometric and kinematic quantities in cutting
    • ISO 3002-4:1984 Part 4: Forces, energy, power
    • ISO 3002-5:1989 Part 5: Basic terminology for grinding processes using grinding wheels
  • ISO 3029:1995 Photography - 126-size cartridges - Dimensions of cartridge, film and backing paper [Withdrawn without replacement]
  • ISO 3040:2016 Geometrical product specifications (GPS) – Dimensioning and tolerancing – Cones
  • ISO 3046 Reciprocating internal combustion engines – Performance
    • ISO 3046-5:2001 Part 5: Torsional vibrations
  • ISO 3082 Iron ores – Sampling and sample preparation procedures
  • ISO 3095:2013 Acoustics – Railway applications – Measurement of noise emitted by railbound vehicles
  • ISO 3098 Technical product documentation – Lettering
    • ISO 3098-1:2015 Part 1: General requirements
    • ISO 3098-2:2000 Part 2: Latin alphabet, numerals and marks
    • ISO 3098-3:2000 Part 3: Greek alphabet
    • ISO 3098-4:2000 Part 4: Diacritical and particular marks for the Latin alphabet
    • ISO 3098-5:1997 Part 5: CAD lettering of the Latin alphabet, numerals and marks
    • ISO 3098-6:2000 Part 6: Cyrillic alphabet
  • ISO 3103 Tea – Preparation of liquor for use in sensory tests
  • ISO 3105:1994 Glass capillary kinematic viscometers – Specifications and operating instructions
  • ISO 3166 Codes for the representation of names of countries and their subdivisions
    • ISO 3166-1:2013 Part 1: Country codes
    • ISO 3166-2:2013 Part 2: Country subdivision code
    • ISO 3166-3:2013 Part 3: Code for formerly used names of countries
  • ISO 3252:1999 Powder metallurgy – Vocabulary
  • ISO 3272 Microfilming of technical drawings and other drawing office documents
    • ISO 3272-1:2003 Part 1: Operating procedures
    • ISO 3272-2:1994 Part 2: Quality criteria and control of 35 mm silver gelatin microfilms
    • ISO 3272-3:2001 Part 3: Aperture card for 35 mm microfilm
    • ISO 3272-4:1994 Part 4: Microfilming of drawings of special and exceptional elongated sizes
    • ISO 3272-6:2000 Part 6: Quality criteria and control of systems for enlargements from 35 mm microfilm
  • ISO 3274:1996 Geometrical Product Specifications (GPS) – Surface texture: Profile method – Nominal characteristics of contact (stylus) instruments
  • ISO 3275:1974 Information processing - Implementation of the 7- bit coded character set and its 7- bit and 8- bit extensions on 3,81 mm magnetic cassette for data interchange
  • ISO 3287:1999 Powered industrial trucks - Symbols for operator controls and other displays
  • ISO 3297:2007 Information and documentation – International standard serial number (ISSN)
  • ISO 3301:1975 Statistical interpretation of data - Comparison of two means in the case of paired observations
  • ISO 3307:1975 Information interchange - Representations of time of the day [Withdrawn: replaced by ISO 8601:1988]
  • ISO 3354:2008 Measurement of clean water flow in closed conduits – Velocity-area method using current-meters in full conduits and under regular flow conditions
  • ISO 3381:2005 Railway applications – Acoustics – Measurement of noise inside railbound vehicles
  • ISO 3394:2012 Packaging - Complete, filled transport packages and unit loads - Dimensions of rigid rectangular packages
  • ISO 3407:1983 Information processing – Information interchange on 3,81 mm (0.150 in) magnetic tape cassette at 4 cpmm (100 cpi), phase encoded at 63 ftpmm (1 600 ftpi)
  • ISO 3408 Ball screws
    • ISO 3408-1:2006 Part 1: Vocabulary and designation
  • ISO 3454:2008 Hydrometry – Direct depth sounding and suspension equipment
  • ISO 3455:2007 Hydrometry – Calibration of current-meters in straight open tanks
  • ISO 3493:2014 Vanilla – Vocabulary
  • ISO 3494:1976 Statistical interpretation of data - Power of tests relating to means and variances
  • ISO 3506 Mechanical properties of corrosion-resistant stainless steel fasteners
  • ISO 3507:1999 Laboratory glassware – Pyknometers
  • ISO 3509:2005 Coffee and coffee products – Vocabulary
  • ISO 3511 Industrial process measurement control functions and instrumentation - Symbolic representation[Note 3]
    • ISO 3511-1:1977 Part 1: Basic requirements
    • ISO 3511-2:1984 Part 2: Extension of basic requirements
    • ISO 3511-3:1984 Part 3: Detailed symbols for instrument interconnection diagrams
    • ISO 3511-4:1985 Part 4: Basic symbols for process computer, interface, and shared display/control functions
  • ISO 3529 Vacuum technology - Vocabulary
    • ISO 3529-1:1981 Part 1: General terms
    • ISO 3529-2:1981 Part 2: Vacuum pumps and related terms
    • ISO 3529-3:2014 Part 3: Total and partial pressure vacuum gauges
  • ISO 3534 Statistics – Vocabulary and symbols
    • ISO 3534-1:2006 Part 1: General statistical terms and terms used in probability
    • ISO 3534-2:2006 Part 2: Applied statistics
    • ISO 3534-3:2013 Part 3: Design of experiments
    • ISO 3534-4:2014 Part 4: Survey sampling
  • ISO 3535:1977 Forms design sheet and layout chart
  • ISO 3536:2016 Road vehicles – Safety glazing materials – Vocabulary
  • ISO 3537 Road vehicles – Safety glazing materials – Mechanical tests
  • ISO 3538 Road vehicles – Safety glazing materials – Test methods for optical properties
  • ISO 3540:1976 Paper or plastic printing ribbons – Characteristics of cores
  • ISO 3561:1976 Information processing – Interchangeable magnetic six-disk pack – Track format
  • ISO 3562:1976 Information processing – Interchangeable magnetic single-disk cartridge (top loaded) – Physical and magnetic characteristics
  • ISO 3563:1976 Information processing – Interchangeable magnetic single-disk cartridge (top loaded) – Track format
  • ISO 3564:1976 Information processing – Interchangeable magnetic eleven-disk pack – Physical and magnetic characteristics
  • ISO 3572:1976 Textiles – Weaves – Definitions of general terms and basic weaves
  • ISO 3591 Sensory analysis – Apparatus – Wine-tasting glass
  • ISO 3593 Starch — Determination of ash
  • ISO 3601 Fluid power systems – O-rings
    • ISO 3601-1 Inside diameters, cross-sections, tolerances and designation codes
    • ISO 3601-2 Housing dimensions for general applications
    • ISO 3601-3 Quality acceptance criteria
    • ISO 3601-4 Anti-extrusion rings (back-up rings)
    • ISO 3601-5 Suitability of elastomeric materials for industrial applications
  • ISO 3602:1989 Documentation – Romanization of Japanese (kana script)
  • ISO 3611:2010 Geometrical product specifications (GPS) – Dimensional measuring equipment: Micrometers for external measurements – Design and metrological characteristics
  • ISO 3632 Spices – Saffron (Crocus sativus L.)[Note 3]
  • ISO 3635:1981 Size designation of clothes – Definitions and body measurement procedure
  • ISO 3650:1998 Geometrical Product Specifications (GPS) – Length standards – Gauge blocks
  • ISO 3660:1976 Fishing nets – Mounting and joining of netting – Terms and illustrations
  • ISO/TR 3666:1998 Viscosity of water
  • ISO 3676:2012 Packaging - Complete, filled transport packages and unit loads - Unit load dimensions
  • ISO 3690 Welding and allied processes — Determination of hydrogen content in arc weld metal
  • ISO 3692:1976 Information processing – Reels and cores for 25,4 mm (1 in) perforated paper tape for information interchange – Dimensions
  • ISO 3713:1987 Ferroalloys - Sampling and preparation of samples - General rules
  • ISO 3715 Ships and marine technology – Propulsion plants for ships
    • ISO 3715-1:2002 Part 1: Vocabulary for geometry of propellers
    • ISO 3715-2:2001 Part 2: Vocabulary for controllable-pitch propeller plants
  • ISO/TS 3716:2006 Hydrometry – Functional requirements and characteristics of suspended-sediment samplers
  • ISO 3740:2000 Acoustics – Determination of sound power levels of noise sources – Guidelines for the use of basic standards
  • ISO 3741:2010 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Precision methods for reverberation test rooms
  • ISO 3743 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering methods for small movable sources in reverberant fields[Note 3]
    • ISO 3743-1:2010 Part 1: Comparison method for a hard-walled test room
    • ISO 3743-2:1994 Part 2: Methods for special reverberation test rooms
  • ISO 3744:2010 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering methods for an essentially free field over a reflecting plane
  • ISO 3745:2012 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Precision methods for anechoic rooms and hemi-anechoic rooms
  • ISO 3746:2010 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Survey method using an enveloping measurement surface over a reflecting plane
  • ISO 3747:2010 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering/survey methods for use in situ in a reverberant environment
  • ISO 3766:2003 Construction drawings – Simplified representation of concrete reinforcement
  • ISO 3767 Tractors, machinery for agriculture and forestry, powered lawn and garden equipment - Symbols for operator controls and other displays
    • ISO 3767-1:2016 Part 1: Common symbols
    • ISO 3767-2:2016 Part 2: Symbols for agricultural tractors and machinery
    • ISO 3767-3:2016 Part 3: Symbols for powered lawn and garden equipment
    • ISO 3767-4:2016 Part 4: Symbols for forestry machinery
    • ISO 3767-5:2016 Part 5: Symbols for manual portable forestry machines
  • ISO/IEC 3788:1990 Information processing – 9-track, 12,7 mm (0,5 in) wide magnetic tape for information interchange using phase encoding at 126 ftpmm (3 200 ftpi), 63 cpmm (1 600 cpi)
  • ISO 3791:1976 Office machines and data processing equipment - Keyboard layouts for numeric applications
  • ISO 3792:1976 Adding machines - Layout of function keyboard
  • ISO 3802:1976 Information processing – General purpose reels with 8 mm (5/16 in) centre hole for magnetic tape for interchange instrumentation applications
  • ISO 3819:2015 Laboratory glassware – Beakers
  • ISO 3822 Acoustics – Laboratory tests on noise emission from appliances and equipment used in water supply installations
    • ISO 3822-1:1999 Part 1: Method of measurement
    • ISO 3822-2:1995 Part 2: Mounting and operating conditions for draw-off taps and mixing valves
    • ISO 3822-3:1997 Part 3: Mounting and operating conditions for in-line valves and appliances
    • ISO 3822-4:1997 Part 4: Mounting and operating conditions for special appliances
  • ISO 3826 Plastics collapsible containers for human blood and blood components
    • ISO 3826-1:2013 Part 1: Conventional containers
    • ISO 3826-2:2008 Part 2: Graphical symbols for use on labels and instruction leaflets
    • ISO 3826-3:2006 Part 3: Blood bag systems with integrated features
    • ISO 3826-4:2015 Part 4: Aphaeresis blood bag systems with integrated features
  • ISO 3828:2008 Shipbuilding and marine structures – Deck machinery – Vocabulary and symbols
  • ISO 3833:1977 Road vehicles – Types – Terms and definitions
  • ISO 3835 Equipment for vine cultivation and wine making – Vocabulary
    • ISO 3835-1:1976 (No part title)
    • ISO 3835-3:1980 (No part title)
    • ISO 3835-4:1981 (No part title)
  • ISO 3846:2008 Hydrometry – Open channel flow measurement using rectangular broad-crested weirs
  • ISO 3847:1977 Liquid flow measurement in open channels by weirs and flumes – End-depth method for estimation of flow in rectangular channels with a free overfall
  • ISO 3855:1977 Milling cutters - Nomenclature
  • ISO 3857 Compressors, pneumatic tools and machines - Vocabulary
    • ISO 3857-1:1977 Part 1: General
    • ISO 3857-2:1977 Part 2: Compressors
    • ISO 3857-3:1989 Part 3: Pneumatic tools and machines
    • ISO 3857-4:2012 Part 4: Air treatment
  • ISO 3861:2005 Rubber hoses for sand and grit blasting - Specification
  • ISO 3864 Graphical symbols – Safety colours and safety signs
  • ISO 3866:1977 Office machines and printing machines used for information processing – Widths of fabric printing ribbons on spools exceeding 19 mm
  • ISO 3877 Tyres, valves and tubes – List of equivalent terms
    • ISO 3877-1:1997 Part 1: Tyres
    • ISO 3877-2:1997 Part 2: Tyre valves
    • ISO 3877-3:1978 Part 3: Tubes
    • ISO 3877-4:1984 Part 4: Solid tyres
  • ISO 3880 Building construction – Stairs – Vocabulary
    • ISO 3880-1:1977
  • ISO 3883:1977 Office machines – Line and character capacity of address masters
  • ISO 3901:2001 Information and documentation – International Standard Recording Code (ISRC)
  • ISO 3911:2004 Wheels and rims for pneumatic tyres – Vocabulary, designation and marking
  • ISO 3918:2007 Milking machine installations – Vocabulary
  • ISO 3950:2016 Dentistry - Designation system for teeth and areas of the oral cavity
  • ISO 3951 Sampling procedures for inspection by variables
    • ISO 3951-1:2013 Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL
    • ISO 3951-2:2013 Part 2: General specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality characteristics
    • ISO 3951-3:2007 Part 3: Double sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
    • ISO 3951-4:2011 Part 4: Procedures for assessment of declared quality levels
    • ISO 3951-5:2006 Part 5: Sequential sampling plans indexed by acceptance quality limit (AQL) for inspection by variables (known standard deviation)
  • ISO 3952 Kinematic diagrams - Graphical symbols
    • ISO 3952-1:1981 (Motion of links of mechanisms; Kinematic pairs; Links and connections of their components; Linkage of bars and their links)
    • ISO 3952-2:1981 (Friction and gear mechanisms; Cam mechanisms)
    • ISO 3952-3:1979 (Maltese and ratchet mechanisms; Couplings and brakes)
    • ISO 3952-4:1984 (Miscellaneous mechanisms and their components)
  • ISO 3966:2008 Measurement of fluid flow in closed conduits – Velocity area method using Pitot static tubes
  • ISO 3977 Gas turbines – Procurement
  • ISO 4006:1991 Measurement of fluid flow in closed conduits - Vocabulary and symbols
  • ISO 4007:2012 Personal protective equipment - Eye and face protection - Vocabulary
  • ISO 4031:1978 Information interchange - Representation of local time differentials [Withdrawn: replaced by ISO 8601:1988]
  • ISO 4037 X and gamma reference radiation for calibrating dosemeters and doserate meters and for determining their response as a function of photon energy
    • ISO 4037-1:1996 Part 1: Radiation characteristics and production
    • ISO 4037-2:1997 Part 2: Dosimetry for radiation protection over the energy ranges from 8 keV to 1,3 MeV and 4 MeV to 9 MeV
    • ISO 4037-3:1999 Part 3: Calibration of area and personal dosemeters and the measurement of their response as a function of energy and angle of incidence
    • ISO 4037-4:2004 Part 4: Calibration of area and personal dosemeters in low energy X reference radiation fields
  • ISO 4046 Paper, board, pulps and related terms – Vocabulary
    • ISO 4046-1:2016 Part 1: Alphabetical index
    • ISO 4046-2:2016 Part 2: Pulping terminology
    • ISO 4046-3:2016 Part 3: Paper-making terminology
    • ISO 4046-4:2016 Part 4: Paper and board grades and converted products
    • ISO 4046-5:2016 Part 5: Properties of pulp, paper and board
  • ISO 4057:1986 Information processing – Data interchange on 6,30 mm (0.25 in) magnetic tape cartridge, 63 bpmm (1 600 bpi) phase-encoded
  • ISO 4063:2009 Welding and allied processes - Nomenclature of processes and reference numbers
  • ISO 4074 Natural latex rubber condoms – Requirements and test methods
  • ISO 4087:2005 Micrographics - Microfilming of newspapers for archival purposes on 35 mm microfilm
  • ISO 4125:1991 Dry fruits and dried fruits – Definitions and nomenclature
  • ISO 4129:2012 Road vehicles - Mopeds - Symbols for controls, indicators and tell-tales
  • ISO 4130:1978 Road vehicles – Three-dimensional reference system and fiducial marks – Definitions
  • ISO 4135:2001 Anaesthetic and respiratory equipment - Vocabulary
  • ISO 4139:1979 Ferrosilicon - Determination of aluminium content - Flame atomic absorption spectrometric method
  • ISO 4140:1979 Ferrochromium and ferrosilicochromium - Determination of chromium content - Potentiometric method
  • ISO 4157 Construction drawings – Designation systems
  • ISO 4158:1978 Ferrosilicon, ferrosilicomanganese and ferrosilicochromium - Determination of silicon content - Gravimetric method
  • ISO 4159:1978 Ferromanganese and ferrosilicomanganese - Determination of manganese content - Potentiometric method
  • ISO 4165 Road vehicles — Electrical connections — Double-pole connection
  • ISO 4172:1991 Technical drawings – Construction drawings – Drawings for the assembly of prefabricated structures
  • ISO 4173:1980 Ferromolybdenum - Determination of molybdenum content - Gravimetric method
  • ISO 4179 Ductile iron pipes and fittings for pressure and non-pressure pipelines – Cement mortar lining
  • ISO 4185:1980 Measurement of liquid flow in closed conduits – Weighing method
  • ISO 4217:2015 Codes for the representation of currencies
  • ISO 4223 Definitions of some terms used in the tyre industry
    • ISO 4223-1:2017 Part 1: Pneumatic tyres
    • ISO 4223-2:1991 Part 2: Solid tyres
  • ISO 4225:1994 Air quality - General aspects - Vocabulary
  • ISO 4226:2007 Air quality – General aspects – Units of measurement
  • ISO 4232 Office machines – Minimum information to be included in specification sheets
    • ISO 4232-3:1984 Part 3: Postal franking machines
  • ISO 4246:1994 Cinematography - Vocabulary
  • ISO 4248:1978 Jig bushes - Definitions and nomenclature
  • ISO 4287:1997 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Terms, definitions and surface texture parameters
  • ISO 4288:1996 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Rules and procedures for the assessment of surface texture
  • ISO 4291:1985 Methods for the assessement of departure from roundness - Measurement of variations in radius
  • ISO 4306 Cranes – Vocabulary
    • ISO 4306-1:2007 Part 1: General
    • ISO 4306-2:2012 Part 2: Mobile cranes
    • ISO 4306-3:2016 Part 3: Tower cranes
    • ISO 4306-5:2005 Part 5: Bridge and gantry cranes
  • ISO 4314 Surface active agents — Determination of free alkalinity or free acidity — Titrimetric method
  • ISO 4337:1977 Information processing – Interchangeable magnetic twelve-disk pack (100 Mbytes)
  • ISO 4341:1978 Information processing – Magnetic tape cassette and cartridge labelling and file structure for information interchange
  • ISO 4346:1977 Steel wire ropes for general purposes - Lubricants - Basic requirements
  • ISO 4359:2013 Flow measurement structures – Rectangular, trapezoidal and U-shaped flumes
  • ISO 4360:2008 Hydrometry – Open channel flow measurement using triangular profile weirs
  • ISO 4362:1999 Hydrometric determinations – Flow measurement in open channels using structures – Trapezoidal broad-crested weirs
  • ISO 4363:2002 Measurement of liquid flow in open channels – Methods for measurement of characteristics of suspended sediment
  • ISO 4364:1997 Measurement of liquid flow in open channels – Bed material sampling
  • ISO 4365:2005 Liquid flow in open channels – Sediment in streams and canals – Determination of concentration, particle size distribution and relative density
  • ISO 4366:2007 Hydrometry – Echo sounders for water depth measurements
  • ISO 4369:1979 Measurement of liquid flow in open channels – Moving-boat method
  • ISO 4371:1984 Measurement of liquid flow in open channels by weirs and flumes – End depth method for estimation of flow in non-rectangular channels with a free overfall (approximate method)
  • ISO 4373:2008 Hydrometry – Water level measuring devices
  • ISO 4374:1990 Liquid flow measurement in open channels – Round-nose horizontal broad-crested weirs
  • ISO 4375:2014 Hydrometry – Cableway systems for stream gauging
  • ISO 4377:2012 Hydrometric determinations – Flow measurement in open channels using structures – Flat-V weirs
  • ISO 4378 Plain bearings - Terms, definitions, classification and symbols
    • ISO 4378-1:2017 Part 1: Design, bearing materials and their properties
    • ISO 4378-2:2017 Part 2: Friction and wear
    • ISO 4378-3:2017 Part 3: Lubrication
    • ISO 4378-4:2009 Part 4: Basic symbols
    • ISO 4378-5:2009 Part 5: Application of symbols
    • ISO/TR 4378-6:2012 Part 6: Abbreviated terms
  • ISO 4412 Hydraulic fluid power – Test code for determination of airborne noise levels
    • ISO 4412-1:1991 Part 1: Pumps
    • ISO 4412-2:1991 Part 2: Motors
    • ISO 4412-3:1991 Part 3: Pumps – Method using a parallelepiped microphone array
  • ISO 4413:2010 Hydraulic fluid power – General rules and safety requirements for systems and their components
  • ISO 4481:1977 Cutlery and flatware – Nomenclature
  • ISO 4548 Methods of test for full-flow lubricating oil filters for internal combustion engines
    • ISO 4548-7:2012 Part 7: Vibration fatigue test
  • ISO 4551:1987 Ferroalloys - Sampling and sieve analysis
  • ISO 4552 Ferroalloys - Sampling and sample preparation for chemical analysis
  • ISO 4578 Adhesives — Determination of peel resistance of high-strength adhesive bonds — Floating-roller method
  • ISO 4582 Plastics — Determination of changes in colour and variations in properties after exposure to daylight under glass, natural weathering or laboratory light sources
  • ISO 4587 Adhesives — Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies
  • ISO 4618:2014 Paints and varnishes – Terms and definitions
  • ISO 4628 Paints and varnishes – Evaluation of degradation of coatings – Designation of quantity and size of defects, and of intensity of uniform changes in appearance
    • ISO 4628-1 General introduction and designation system
    • ISO 4628-2 Assessment of degree of blistering
    • ISO 4628-3 Assessment of degree of rusting
    • ISO 4628-4 Assessment of degree of cracking
    • ISO 4628-5 Assessment of degree of flaking
    • ISO 4628-6 Assessment of degree of chalking by tape method
    • ISO 4628-7 Assessment of degree of chalking by velvet method
    • ISO 4628-8 Assessment of degree of delamination and corrosion around a scribe
    • ISO 4628-10 Assessment of degree of filiform corrosion
  • ISO 4683 Raw sheep skins
    • ISO 4683-1:1998 Part 1: Descriptions of defects
  • ISO 4720:2009 Essential oils – Nomenclature
  • ISO 4730:2017 Essential oil of Melaleuca, terpinen-4-ol type (Tea Tree oil)
  • ISO 4786:1977 Enclosed-scale adjustable-range thermometers
  • ISO 4787:2010 Laboratory glassware – Volumetric instruments – Methods for testing of capacity and for use
  • ISO 4788:2005 Laboratory glassware – Graduated measuring cylinders
  • ISO 4791 Laboratory apparatus – Vocabulary relating to apparatus made essentially from glass, porcelain or vitreous silica
    • ISO 4791-1:1985 Part 1: Names for items of apparatus
  • ISO 4795:1996 Glass for thermometer bulbs
  • ISO 4801:1979 Glass alcoholometers and alcohol hydrometers not incorporating a thermometer
  • ISO 4805:1982 Laboratory glassware – Thermo-alcoholometers and alcohol-thermohydrometers
  • ISO 4831:2006 Microbiology of food and animal feeding stuffs – Horizontal method for the detection and enumeration of coliforms – Most probable number technique
  • ISO 4832:2006 Microbiology of food and animal feeding stuffs – Horizontal method for the enumeration of coliforms – Colony-count technique
  • ISO 4833 Microbiology of the food chain – Horizontal method for the enumeration of microorganisms
    • ISO 4833-1:2013 Part 1: Colony count at 30 degrees C by the pour plate technique
    • ISO 4833-2:2013 Part 2: Colony count at 30 degrees C by the surface plating technique
  • ISO 4866:2010 Mechanical vibration and shock – Vibration of fixed structures – Guidelines for the measurement of vibrations and evaluation of their effects on structures
  • ISO 4871:1996 Acoustics – Declaration and verification of noise emission values of machinery and equipment
  • ISO/IEC 4873:1991 Information technology – ISO 8-bit code for information interchange – Structure and rules for implementation
  • ISO 4875 Metal-cutting band saw blades
    • ISO 4875-1:2006 Part 1: Vocabulary
  • ISO 4880:1997 Burning behaviour of textiles and textile products - Vocabulary
  • ISO 4882:1979 Office machines and data processing equipment - Line spacings and character spacings
  • ISO 4885:2017 Ferrous materials - Heat treatments - Vocabulary
  • ISO 4892 Plastics – Methods of exposure to laboratory light sources
  • ISO 4902:1989 Information technology – Data communication – 37-pole DTE/DCE interface connector and contact number assignments
  • ISO 4903:1989 Information technology – Data communication – 15-pole DTE/DCE interface connector and contact number assignments
  • ISO/IEC 4909:2006 Identification cards - Financial transaction cards - Magnetic stripe data content for track 3
  • ISO 4921:2000 Knitting – Basic concepts – Vocabulary

Notes[edit]

  1. ^ This list generally excludes draft versions.
  2. ^ ISO deliverables include "specifications" (ISO/PAS, ISO/TS), "reports" (ISO/TR), etc, which are not referred to by ISO as "standards".
  3. ^ a b c d e f g h i j The exact wording of this title varies between parts. This is the wording of the most recently published part.

References[edit]

  1. ^ "Standards catalogue". ISO.
  2. ^ "Freely Available Standards". ISO.
  3. ^ https://www.iso.org/standard/59765.html
  4. ^ https://www.iso.org/standard/45103.html

External links[edit]