Jump to content

Compressed-air vehicle

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by 2601:704:580:3642:38b2:cc88:42c1:9c6d (talk) at 01:24, 27 November 2022 (Missing the). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

compressed air system with a PCM heat exchanger prototype by Dr. Reza Alizade Evrin from Ontario Tech University.[1][2]
Compressed air system with a PCM heat exchanger prototype diagram

A compressed-air vehicle (CAV) is a transport mechanism fueled by tanks of pressurized atmospheric gas and propelled by the release and expansion of the gas within a pneumatic motor.

CAV's have found application in torpedoes, locomotives used in situations where standard locomotives are a hazard, and early prototype submarines.

Compressed-air vehicles operate according to a thermodynamic process where air cools down when expanding and heats up when being compressed and those are thermal energy losses that drain the capacity factor, however with the recent developments in isothermal compressed air energy storage ICAES plants, compressed air storage has reached 4 times the capacity factor of lithium-ion batteries with 2.7Mj/kg or 3.6Mj/m3 [3] and in 2020 there has been developments in ICAV car or isothermal compressed air vehicle published by Dr. Reza Alizade Evrin from Ontario Tech University[1][2] with a first prototype that uses low pressure air tanks and exhaust air recovery to power a paraffin heat exchanger system with a global energy efficiency of 74% (reaching 73%-90% efficiency of lithium-ion electric cars) with a driving range of 140 km. This efficiency and range can be increased by using storage tank as vehicle chassis structure, high pressure tanks, new rotary engines, and a more efficient heat exchanger, this breakthrough together with the availability of recycled and bio-based thermoplastics for tanks and pneumatic components and renewable energy means this technology can be the basis of a free green transportation revolution with energy and circular industry decentralization with open source numerical control machines fabrication including additive manufacturing while multistage air compressors and coolers or hydraulic pumps can be attached directly to VAWT wind turbines, stirling engine with a parabolic or fresnel lens solar concentrator or river, tidal, wave hydropower turbine with no electric energy or electric grid needed nor energy conversion inefficiencies or additional energy storage, also instead of onboard heat recovery system there can be used a refillable molten salt (from fresnel lens or parabolic Concentrated solar power) reservoir in a heat exchanger system.

Compressed-air propulsion may also be incorporated in hybrid systems, such as with battery electric propulsion. This kind of system is called a hybrid-pneumatic electric propulsion. Additionally, regenerative braking can also be used in conjunction with this system.

Compressed air engines

In principle, any Pneumatic motor can be used for an compressed-air vehicle, but some engines were specifically developed for this application and/or have specific advantages.

di pietro engine

Dipietro eccentric shaft, rotary vane air engine

There have been several dubious claims with undisclosed information. However, the "di pietro" engine has been partially tested with CAD and finite element analysis program and published in scientific papers by Jarosław Zwierzchowski from Lodz University of Technology in 2017,[4] which is an eccentric shaft vane motor that uses low air pressure.

Liquidpiston

LiquidPiston rotary engine [5]

Another recent engine that could be adapted to compressed air is Liquidpiston rotary engine.[5]

Compressed air tanks and collision safety

Hyundai nexo high pressure hydrogen tank safety
DuraStor consortium Thermoplastic composite pressure vessels for hydrogen vehicles [6]
Main article: Compressed air tank

The tanks must be designed to safety standards appropriate for a pressure vessel, such as ISO 11439.[7]

The pressure vessels or air storage tanks that can be used in compressed air vehicles can be made of low pressure (9 atm) or high pressure (+240 atm), and can be made of composite materials like thermoplastic and fiber reinforced thermoplastics,[6][8] that means that the price can drop by using recycled or biobased thermoplastics using rotational molding and they are much lighter than lithium-iron batteries and 70% lighter compared to steel tanks, also they have more lifespan and don't need much maintenance.

To reduce vehicle weight further the air tanks can be used as structural storage so the tank is the main part of the vehicle chassis while using appropriate impact isolation, however fiber reinforced thermoplastic tanks only have ruptures in case of collision and don't explode. The advance in pressure vessels for vehicles have been developed for hydrogen vehicles with high compression pressure vessels, this is a quote from the hyundai webpage which have created the Hyundai Nexus with 700 atm tanks and favourable crash tests.[9]

” Hydrogen tanks require ‘High Strength’ to prevent rupture and ‘High Stiffness’ for durability. Strength is defined as the level of resistance to an influence of an external force. Stiffness is the level of resistance maintaining its original shape. The carbon fiber materials used in making hydrogen fuel tanks is as light as a plastic but has six and four times the strength and stiffness of steel, respectively. “When a bullet penetrates a hydrogen tank, it does not explode. Instead, hydrogen leaks out through the bullet hole. In a standard collision test, not even a tiny amount of hydrogen was detected because none had leaked out.

Compressed air production, storage and energy efficiency and density

Wind Turbine Air Compressor posted Fieldlines.com: The Otherpower discussion board [10]
wind turbine powered hydraulic pump with Open Accumulator for Isothermal Compressed Air Energy Storage ICAES System [11]

Compressed air has a low energy density, however near isothermal compressed air storage ICAES has almost 4 times lithium-ion batteries capacity with 2.7Mj/kg or 3.6Mj/m3.[3]

Compressed air can be produced by attaching an air compressor or hydraulic pump to a wind turbine[10][11] or using river, tidal, wave hydropower turbine with only a conversion from mechanical to pneumatic energy, eliminating electricity from the loop which gives higher efficiency overall.

Also there is the possibility of using thermal energy with a parabolic or fresnel lens solar concentrator to power a thermal stirling engine to move the compressor or pump, as solar stirling is more efficient than solar steam and Photovoltaic. (see also Solar-powered Stirling engine)

Emission output

Since the compressed air is filtered to protect the compressor machinery, the air discharged has less suspended dust in it, though there may be carry-over of lubricants used in the compressor or engine. This can be mitigated by using oil free air compressors.

Resource consumption

The recent developments of composite pressure vessels and pneumatic components means that compressed air vehicles can be part of the circular industry with biobased or recycled components. Also by cutting electric energy from the loop there is no need for electric grid and the metals used like cooper, iron in magnets, etc.

History

Gotthardbahn: Pneumatic Locomotive with attached pressure container.[12]

Compressed air has been used since the 19th century to power mine locomotives and trams in cities such as Paris (via a central, city-level, compressed air energy distribution system), and was previously the basis of naval torpedo propulsion.

During the construction of the Gotthardbahn from 1872 to 1882, pneumatic locomotives were used in the construction of the Gotthard Rail Tunnel and other tunnels of the Gotthardbahn.

In 1903, the Liquid Air Company located in London, United Kingdom, manufactured a number of compressed-air and liquified-air cars. The major problem with these cars and all compressed-air cars is the lack of torque produced by the "engines" and the cost of compressing the air.[13]

Since 2010, several companies have started to develop compressed air cars, including hybrid types that also include a petrol driven engine; none has been released to the public, or have been tested by third parties.

Advantages

Energy efficiency of the energy source, by using wind turbines to compressors or pumps there is a single conversion of mechanical to pneumatic or hydraulic energy,[11] and by powering the compressor with stirling engine with a parabolic or fresnel lens solar concentrator there's thermal energy to mechanical energy conversion, also by using a phase change material in the heat exchanger heated with concentrated solar power there is only solar thermal energy involved.

Energy efficiency of the vehicle, as of 2020 the first isothermal prototype reaches 74%,[1][2] which is similar to the 73-90% of electric vehicles using lithium-ion.

Energy density compared to lithium-ion, Isothermal compressed air energy storage ICAES energy density can be at least 2.7Mj/kg or 3.6Mj/m3, 4 times [3] of lithium-ion batteries, which can be improved with high pressure vessels and heat exchanger systems.

Resources, compressed air technology can be adapted to renewable energy and circular industry with biobased or recycled composites and so compared to electric vehicles they can be exempt from finite mineral resources or toxic processes used in battery and electric motor manufacturing and also from the electric grid use.[6]

Structural weight, the low weight of composite pressure vessels relative to lithium-ion battery and also compared to steel tanks (70% lighter),[8] which that can be reduced by using the tanks as vehicle chassis structure with appropriate impact isolation, also the low weight of wheel hub motor rotary engines.

Refilling is possible in almost any place or with onboard equipment, because the only thing necessary is wind, solar power or river, tidal, wave hydropower to move an air compressor, hydraulic pump or stirling engine.

Energy synergy with the available pneumatic energy, so all vehicle mechatronics systems can be powered by small air motors, and also the vehicle can use active pneumatic suspension, pneumatic steering or pneumatic shock absorption bumpers,[14] also there can be provided air conditioning or climate control with the using the low temperature created during air expansion.

Energy recovery systems with regenerative suspension and Regenerative braking producing low pressure compressed air to be stored in an additional pressure vessel.

Low noise of pistonless rotary engines while using compressed air, which can also being soundproofed because the low temperature in which it works.

Zero fire hazard, which makes it one of the few transportation systems that cannot produce spontaneous or after-collision fire or explosions like in the case of petrol, ethanol, hydrogen and also battery vehicles.

Disadvantages

Energy density of compressed air compared to liquid nitrogen or hydrogen.

Energy efficiency of compressed air engine compared to micro gas turbine with adequate soundproofing that can be used in hybrid gas turbine-electric motor vehicles with a mixture of compressed air, liquid nitrogen or hydrogen (previous gas turbine powered vehicles have used a setup for speed, rather than efficiency consisting in a large noise gas turbines connected to the transmission) since the gas turbine (which are used in thermal power plants due to its efficiency) outperforms pistonless rotary engines, however the production of compressed air is more energy efficient and so requires less wind power and infrastructure and also there is a loss of efficiency from gas turbine to generator and to electric motor.

While batteries can somewhat maintain their voltage throughout their discharge and chemical fuel tanks provide the same power densities from the first to the last litre, the pressure of compressed air tanks falls as air is drawn off, reducing available power.

Possible improvements

It may be possible to store compressed air at lower pressure using an absorption material within the tank. Absorption materials like Activated carbon,[15] or a metal organic framework[16] is used for storing compressed natural gas at 500 psi instead of 4500 psi, which amounts to a large energy saving.

Vehicles

Compressed-air locomotive used in boring the Rove canal tunnel in France

Production cars

Main article: Compressed air car

Several companies are investigating and producing prototype,s including hybrid compressed-air/gasoline-combustion vehicles. As of August 2017, none of the developers have yet gone into production, although Tata has indicated they will begin selling vehicles from 2020[17] and MDI's US distributor Zero Pollution Motors says production of the AIRPod will commence in Europe in 2018.[18]

Experimental cars and bikes

In 2008, a compressed air and natural gas powered vehicle designed by engineering students at Deakin University in Australia was joint winner of the Ford Motor Company T2 competition to produce a car with a 200 km range and an estimated cost of less than $7,000.[19][20]

Australian company Engineair has produced a number of vehicle types - moped, small car, small carrier, go-cart - around the rotary compressed air engine created by Angelo Di Pietro.

A compressed-air powered motorcycle, called the Green Speed Air Powered Motorcycle was made by Edwin Yi Yuan, based on the Suzuki GP100 and using the Angelo Di Pietro compressed-air engine.[21]

Three mechanical engineering students from San Jose State University; Daniel Mekis, Dennis Schaaf and Andrew Merovich, designed and built a bike that runs on compressed air. The total cost of the prototype was under $1000 and was sponsored by Sunshops (on the Boardwalk in Santa Cruz, California) and NO DIG NO RIDE (from Aptos, California.). The top speed of the maiden voyage in May 2009 was 23 mph. While their design was simple, these three pioneers of compressed air powered vehicles helped pave the way[citation needed] for French automaker Peugeot Citroën to invent a brand new air-powered hybrid. The 'Hybrid Air' system uses compressed air to move the car's wheels when driving under 43 mph. Peugeot says the new hybrid system should get up to 141 miles per gallon of gas. Models should roll out as early as 2016. [1]. The head of the project left Peugeot in 2014 and in 2015 the company said it had been unable to find a partner to share the development costs, effectively ending the project.[22]

"Ku:Rin" named air-compressed three-wheeler vehicle was created by Toyota in 2011. The speciality about this vehicle is it has registered a record-breaking highest speed 129.2 km/h (80 mph) even if it has engine which uses only compressed air. This car was developed by the company's "Dream car workshop". This car is nicknamed as "sleek rocket", or "pencil shaped rocket".[23]

As part of the TV-show Planet Mechanics, Jem Stansfield and Dick Strawbridge converted a regular scooter to a compressed air moped.[24] This has been done by equipping the scooter with a compressed-air engine and air tank.[25]

In 2010, Honda presented the Honda Air concept car at the LA Auto Show.[26]

Since 2008 the former Bosch Rexroth, now Emerson is organizing the Emerson’s International AVENTICS Pneumobile Competition in Eger, Hungary. It is a competition for students in the higher education to build racing vehicles propelled by compressed air.[27]

Óbuda University PowAir Pneumobil Team

There is an international conference related to the event organized by Óbuda University, Department of Bánki Donát Mechanical and Safety Engineering.[28]

Trains, Trams, Boats and Planes

Preserved Nantes compressed air tramcar at the AMTUIR museum

Compressed-air locomotives are a kind of fireless locomotive and have been used in mining[29] and tunnel boring.[30]

Various compressed-air-powered trams were trialled, starting in 1876. In Nantes and Paris Mekarski system trams ran in regular service for over 30 years.[31] See also Nantes tramway#Compressed air trams (1879-1917).

Currently, no water or air vehicles exist that make use of the compressed air engine. Historically certain torpedoes were propelled by compressed-air engines.

See also

References

  1. ^ a b c "Compressed air cars for urban transportation". advancedsciencenews. 7 September 2020. Retrieved 2020-09-07.
  2. ^ a b c Evrin, Reza Alizade; Dincer, Ibrahim (2020). "Experimental investigation of a compressed air vehicle prototype with phase change materials for heat recovery". Energy Storage. 2 (5). onlinelibrary.wiley. doi:10.1002/est2.159. S2CID 219020514. Retrieved 2020-04-27.
  3. ^ a b c Odukomaiya, Adewale; Abu-Heiba, Ahmad; Gluesenkamp, Kyle R.; Abdelaziz, Omar; Jackson, Roderick K.; Daniel, Claus; Graham, Samuel; Momen, Ayyoub M. (2016). "Thermal analysis of near-isothermal compressed gas energy storage system". Applied Energy. 179. semantic scholar: 948–960. doi:10.1016/J.APENERGY.2016.07.059. OSTI 1324083. S2CID 113436358. Retrieved 2016-07-13.
  4. ^ "Design type air engine Di Pietro". 2017-07-18. Retrieved 2017-10-13.
  5. ^ a b "Development of a Small Rotary SI/CI Combustion Engine". 2014-07-18. Retrieved 2014-10-13.
  6. ^ a b c "Thermoplastic composite pressure vessels for FCVs". compositesworld.com. 2015-02-01. Retrieved 2015-02-01.
  7. ^ "Gas cylinders – High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles". Iso.org. 2006-07-18. Retrieved 2010-10-13.
  8. ^ a b "High pressure gas tanks in thermoplastic composites". plastics.gl. 2014-05-01. Retrieved 2014-05-01.
  9. ^ "OHydrogen Tank: Safety Proven (OA-ICAES) System". hyundaimotorgroup. Retrieved 2019-07-13.
  10. ^ a b "Wind Turbine Air Compressor". Retrieved 2015-07-13.
  11. ^ a b c "Open Accumulator Isothermal Compressed Air Energy Storage (OA-ICAES) System". Retrieved 2018-07-13.
  12. ^ Braun, Adolphe: Luftlokomotive in "Photographische Ansichten der Gotthardbahn", Dornach im Elsass, ca. 1875
  13. ^ "History and Directory of Electric Cars from 1834 to 1987". Didik.com. Retrieved 2009-09-19.
  14. ^ "Automated Pneumatic Bumper For Vehicle Safety". 2012-05-01. Retrieved 2014-05-01.
  15. ^ "National Science Foundation (NSF) News – From Farm Waste to Fuel Tanks – US National Science Foundation (NSF)". nsf.gov. Retrieved 2010-10-13.
  16. ^ Ma Shengqian (2008). "Metal-Organic Framework from an Anthracene Derivative Containing Nanoscopic Cages Exhibiting High Methane Uptake". Journal of the American Chemical Society. 130 (3): 1012–1016. doi:10.1021/ja0771639. PMID 18163628.
  17. ^ "Tata Motors' air-powered car project still on, to be launch ready in 3 years". Auto Car Professional. Retrieved 24 August 2017.
  18. ^ Zero Pollution Motors http://zeropollutionmotors.us/. Retrieved 25 August 2017. {{cite web}}: Missing or empty |title= (help)
  19. ^ "Deakin Green Car Showcased in Ford Global Challenge". Deakin University. Retrieved 25 August 2017.
  20. ^ "Ford Model T Design Challenge: the winners". Car Body Design. Retrieved 25 August 2017.
  21. ^ "Green Speed Air Powered Motorcycle". Archived from the original on February 18, 2011. Retrieved May 29, 2020.
  22. ^ "PSA : la révolution de l'Hybrid Air n'aura pas lieu". Les Echos. Jan 11, 2015. Retrieved May 29, 2020.
  23. ^ "Toyota three-wheeler does 80.3 mph on compressed air". Physorg.com. Retrieved 2012-08-11.
  24. ^ "Compressed air moped conversion". Archived from the original on April 1, 2008. Retrieved May 29, 2020.
  25. ^ "Compressed air moped being built by Jem Stansfield". Ecogeek.org. Archived from the original on 2010-08-11. Retrieved 2010-10-13.
  26. ^ "Honda Air concept car". Greenoptimistic.com. 2010-10-22. Retrieved 2012-01-26.
  27. ^ "Pneumobile2020". pneumobil.hu. 2020-03-09. Retrieved 2020-03-09.
  28. ^ "ACIPV2020". pneumobil.hu. 2020-03-09. Retrieved 2020-03-09.
  29. ^ "Compressed-Air Propulsion". Mar 3, 2016. Archived from the original on March 3, 2016. Retrieved May 29, 2020.
  30. ^ "Scientific American 1916-11-25". Jun 25, 2016. Archived from the original on June 25, 2016. Retrieved May 29, 2020.
  31. ^ "Tramway Information". Tramwayinfo.com. Retrieved 2010-10-13.
Wikimedia Commons has media related to Compressed-air-powered vehicles.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Compressed-air_vehicle&oldid=1124040311"