Steam locomotive

From Wikipedia, the free encyclopedia
  (Redirected from Steam train)
Jump to: navigation, search
Drawing of a Great Western Railway King class locomotive
Russian B-series steam locomotive in service circa 1910. It could haul passenger trains at speeds up to 125 km per hour.[1]

A steam locomotive is a railway locomotive that produces its pulling power through a steam engine. These locomotives are fueled by burning combustible material, usually coal, wood or oil, to produce steam in a boiler. The steam moves reciprocating pistons which are mechanically connected to the locomotive's main wheels. Both fuel and water supplies are carried with the locomotive, either on the locomotive itself or in wagons (tenders) pulled behind. The first steam was made by Richard Trevithick on the 21st of Feb 1804.

Steam locomotives were first developed in Great Britain during the early 19th century and dominated railway transport until the middle of the 20th century. From the early 1900s they were gradually superseded by electric and diesel locomotives.

Origins[edit]

Trevithick's 1802 Coalbrookdale locomotive
Stephenson's Rocket 1829, the winner of the Rainhill Trials

The earliest railways employed horses to draw carts along railway tracks.[2] In 1784, William Murdoch, a Scottish inventor, built a prototype steam road locomotive.[3] An early working model of a steam rail locomotive was designed and constructed by steamboat pioneer John Fitch in the US during 1794.[4] His steam locomotive used interior bladed wheels guided by rails or tracks. The model still exists at the Ohio Historical Society Museum in Columbus.[5]

The first full-scale working railway steam locomotive was built by Richard Trevithick in the United Kingdom and, on 21 February 1804, the world's first railway journey took place as Trevithick's unnamed steam locomotive hauled a train along the tramway from the Pen-y-darren ironworks, near Merthyr Tydfil, to Abercynon in South Wales.[6][7] Accompanied with Andrew Vivian, it ran with mixed success.[8] The design incorporated a number of important innovations that included using high-pressure steam which reduced the weight of the engine and increased its efficiency. Trevithick visited the Newcastle area in 1804 and he had a ready audience of colliery owners and engineers. The visit was so successful that the colliery railways in north-east England became the leading centre for experimentation and development of the steam locomotive.[9] Trevithick continued his own steam propulsion experiments through another trio of locomotives, concluding with the Catch Me Who Can in 1808. Four years later, the successful twin-cylinder locomotive Salamanca by Matthew Murray for the edge railed rack and pinion Middleton Railway debuted in 1812.[10] Another well known early locomotive was Puffing Billy, built 1813-1814 by engineer William Hedley. It was intended to work on the Wylam Colliery near Newcastle upon Tyne. This locomotive is the oldest preserved, and is on static display in the Science Museum, London. George Stephenson built the Locomotion for the Stockton and Darlington Railway, north-east England, which was the first public steam railway in the world. In 1829, he built The Rocket which was entered in and won the Rainhill Trials. This success led to Stephenson establishing his company as the pre-eminent builder of steam locomotives used on railways in the UK, US and much of Europe.[11] The Liverpool and Manchester Railway opened a year later making exclusive use of steam power for passenger and goods trains.

The US started developing steam locomotives in 1830 with the Baltimore and Ohio Railroad's Tom Thumb. This was the first US-built locomotive to run in America, Stourbridge Lion being the first, although it was intended as a demonstration of the potential of steam traction, rather than as a revenue-earning locomotive. Many of the earliest locomotives for American railroads were imported from Great Britain, including the Stourbridge Lion and the John Bull (still the oldest operable engine-powered vehicle in the United States of any kind, as of 1981) but a domestic locomotive manufacturing industry was quickly established, with locomotives like the DeWitt Clinton being built in the 1830s.[11]

The first railway service in Continental Europe (or for that matter, anywhere outside the UK and the US) was opened on 5 May 1835 in Belgium, between Mechelen and Brussels. The name of the locomotive used was The Elephant.

In Germany the first working steam locomotive was a rack-and-pinion engine, similar to the Salamanca, designed by the British locomotive pioneer John Blenkinsop. Built in June 1816 by Johann Friedrich Krigar in the Royal Berlin Iron Foundry (Königlichen Eisengießerei zu Berlin), the locomotive ran on a circular track in the factory yard. It was the first locomotive to be built on the European mainland and the first steam-powered passenger service, because curious onlookers could ride in the attached coaches for a fee. It is portrayed on a New Year's badge for the Royal Foundry dated 1816. Another locomotive was built using the same system in 1817. They were to be used on pit railways in Königshütte and in Luisenthal on the Saar (today part of Völklingen), but neither could be returned to working order after being dismantled, moved and reassembled. On 7 December 1835 the Adler ran for the first time between Nuremberg and Fürth on the Bavarian Ludwig Railway. It was the 118th engine from the locomotive works of Robert Stephenson and stood under patent protection.

The Austria, the first locomotive in Austria

In 1837 the first steam railway started in Austria on the Emperor Ferdinand Northern Railway between Vienna-Floridsdorf and Deutsch-Wagram. The oldest continually working steam engine in the world also runs in Austria: the GKB 671 built in 1860, has never been taken out of service, and is still used for special excursions.

In 1838 the third steam locomotive to be built in Germany, the Saxonia, was manufactured by the Maschinenbaufirma Übigau near Dresden, built by Prof. Johann Andreas Schubert. The first independently designed locomotive in Germany was the Beuth built by August Borsig in 1841. In 1848 the first locomotive produced by Henschel-Werke in Kassel, the Drache, was delivered.

The first railway line over Swiss territory was the StrasbourgBasle line opened in 1844. Three years later, in 1847, the first fully Swiss railway line, the Spanisch Brötli Bahn, from Zürich to Baden was opened.

Basic form[edit]

The main components of a steam locomotive
01. Firebox

02. Ashpan

03. Water (inside the boiler)

04. Smokebox

05. Cab

06. Tender

07. Steam Dome

08. Safety Valve

09. Regulator Valve

10. Superheater Header in smokebox

11. Piston

12. Blastpipe

13. Valve Gear

14. Regulator Rod

15. Drive Frame

16. Rear Pony Truck

17. Front Pony Truck

18. Bearing and Axlebox

19. Leaf Spring

20. Brake shoe

21. Air brake pump

22. (Front) Centre Coupler,

23. Whistle

24. Sandbox.

Boiler[edit]

Although other types of boiler have been tried both historically and latterly with steam locomotives, their use did not become widespread, and the firebox fire-tube boiler has been the dominant source of power in the age of steam locomotion from the Rocket in 1829 to the Mallard in 1938 and beyond.

A steam locomotive with the boiler and firebox exposed (firebox on the left)

The steam locomotive, when fired up, typically employs a steel firebox fire-tube boiler that contains a heat source to the rear, which generates and maintains a head of steam within the pressurised partially water filled area of the boiler to the front.

The heat source, contained within the firebox, is the energy released by the combustion, typically of a solid or liquid fuel, with the by-product of hot combustion gases. If wood, coal or coke is used as the combustion material it is introduced through a door, typically by a fireman, onto a set of grates where ashes fall away from the burning fuel. If oil is used a door provides for adjusting the air flow, maintenance or for cleaning the oil jets.

The fire-tube boiler is characterised by internal tubes connected to the firebox that guide the smoke and hot combustion gases through the pressurised wet area of the boiler. These tubes greatly increase the contact area between the hot and the wet areas of the boiler and this increases the efficiency of the thermal conduction and thermal radiation processes of heat transfer between the two. The combustion gases emerge from the ends of the fire-tubes at the front of the boiler and are discharged via the smokebox to the chimney (stack or smokestack in the US). Surrounding the boiler are layers of insulation or lagging to minimize heat loss to the surroundings.

The amount of pressure in the boiler can be monitored by a gauge mounted in the cab and excessive steam pressure can be released manually by the driver or fireman. Alternatively in conditions of high boiler pressure, a safety valve may be triggered to reduce pressure and prevent the boiler violently bursting, which had previously resulted in injuries and fatalities to nearby individuals, as well as extensive damage to the locomotive and nearby structures.

Aftermath of a boiler explosion on a railway locomotive circa 1850.

At the front of the boiler is the smokebox, into which used exhaust steam is injected to increase the draught of smoke and combustion gases through the fire tubes in the boiler and out through the chimney. The quest for thermal efficiency greater than that of the typical fire-tube boiler led such engineers as Nigel Gresley to consider such innovations as the water-tube boiler: although he tested the concept on the LNER Class W1, the difficulties during development exceeded to will to proceed with the problem at the time.

The steam generated in the boiler not only propels the locomotive, but also energizes such other devices as whistles, brakes, pumps, and passenger car heating systems. The constant demand for steam requires a continuous supply of water to the boiler, usually pumped into it automatically. The source of this water is an unpressurised tank that is usually part of the locomotive's tender or is wrapped around the boiler in the case of a tank locomotive. Periodic stops are required to refill the water.

During operation, the boiler's water level is constantly monitored, normally via a transparent tube referred to as a sight glass, or with a gauge. Maintaining a proper water level is central to the efficient and safe operation of the boiler. If the water level is too high, steam production is decreased, efficiency is lost and in extreme cases, water will be carried out with the steam into the cylinders, possibly causing mechanical damage. More seriously, if the water level gets too low, the crown (top) and/or side sheets of the firebox may become exposed. Without sufficient water to absorb the heat of combustion, the firebox sheets may soften and melt, with the possible result of high-pressure steam being ejected with tremendous force through the firebox and into the locomotive's cab. The development of the fusible plug to release pressure in conditions of excessively high temperature and low water levels was designed to protect against this occurrence.

Scale may build up in boiler and prevent proper heat transfer, and corrosion will eventually degrade the boiler's materials to the point where it needs to be rebuilt or replaced. Start-up on a large engine may take hours of preliminary heating of the boiler water before sufficient steam is available.

Although the boiler is typically placed horizontally, for locomotives designed to work in locations with steep slopes it may be more appropriate to consider a vertical boiler or one mounted such that the boiler remains horizontal but the wheels are inclined to suit the slope of the rails.

Steam circuit [edit]

The steam generated in the boiler fills the steam space above the water in the partially filled boiler. Its maximum working pressure is limited by spring-loaded safety valves. It is then collected either in a perforated tube fitted above the water level or from a dome that often houses the regulator valve, or throttle, the purpose of which is to control the amount of steam leaving the boiler. The steam then either travels directly along and down a steam pipe to the engine unit or may first pass into the wet header of a superheater, the role of the latter being to improve thermal efficiency and eliminate water droplets suspended in the "saturated steam", the state in which it leaves the boiler. On leaving the superheater, the steam exits the dry header of the superheater and passes down a steam pipe entering the steam chests adjacent to the cylinders of a reciprocating engine. Inside each steam chest is a sliding valve that distributes the steam via ports that connect the steam chest to the ends of the cylinder space. The role of the valves is twofold: admission of each fresh dose of steam and exhaust of the used steam once it has done its work.

The cylinders are double acting, with steam admitted to each side of the piston in turn. In a two-cylinder locomotive, one cylinder is located on each side of the locomotive. The cranks are set 90° out of phase. During a full rotation of the driving wheel, steam provides four power strokes; each cylinder receives two injections of steam per revolution. The first stroke is to the front of the piston and the second stroke to the rear of the piston; hence two working strokes. Consequently two deliveries of steam onto each piston face in two cylinders generates a full revolution of the driving wheel. Each piston is connected to the driving axle on each side by a connecting rod, the driving wheels are connected together by coupling rods to transmit power from the main driver to the other wheels. Note that at the two "dead centres", when the connecting rod is on the same axis as the crankpin on the driving wheel, the connecting rod applies no torque to the wheel. Therefore, if both cranksets could be at "dead centre" at the same time, and the wheels should happen to stop in this position, the locomotive could not be started moving. Therefore the crankpins are attached to the wheels at a 90° angle to each other, so only one side can be at dead centre at a time.

Each piston transmits power directly through a connecting rod (US: main rod) and a crankpin (US: wristpin) on the driving wheel (US main driver) or to a crank on a driving axle. The movement of the valves in the steam chest is controlled through a set of rods and linkages called the valve gear, actuated from the driving axle or from the crankpin; the valve gear includes devices that allow reversing the engine, adjusting valve travel and the timing of the admission and exhaust events. The cut-off point determines the moment when the valve blocks a steam port, "cutting off" admission steam and thus determining the proportion of the stroke during which steam is admitted into the cylinder; for example a 50% cut-off admits steam for half the stroke of the piston. The remainder of the stroke is driven by the expansive force of the steam. Careful use of cut-off provides economical use of steam and, in turn, reduces fuel and water consumption. The reversing lever (US: Johnson bar), or screw-reverser (if so equipped), that controls the cut-off therefore performs a similar function to a gearshift in an automobile—maximum cut-off, providing maximum tractive effort at the expense of efficiency, is used to pull away from a standing start, whilst a cut-off as low as 10% is used when cruising, providing reduced tractive effort with lower fuel/water consumption.[12]

Exhaust steam is directed upwards to the atmosphere through the chimney, by way of a nozzle called a blastpipe that gives rise to the familiar "chuffing" sound of the steam locomotive. The blastpipe is placed at a strategic point inside the smokebox that is at the same time traversed by the combustion gases drawn through the boiler and grate by the action of the steam blast. The combining of the two streams, steam and exhaust gases, is crucial to the efficiency of any steam locomotive, and the internal profiles of the chimney (or, more strictly speaking, the ejector) require careful design and adjustment. This has been the object of intensive studies by a number of engineers (and almost totally ignored by others with sometimes catastrophic effect). The fact that the draught depends on the exhaust pressure means that power delivery and power generation are automatically self-adjusting. Among other things, a balance has to be struck between obtaining sufficient draught for combustion whilst giving the exhaust gases and particles sufficient time to be consumed. In the past, fierce draught could lift the fire off the grate, or cause the ejection of unburnt particles of fuel, dirt and pollution for which steam locomotives had an unenviable reputation. Moreover, the pumping action of the exhaust has the counter effect of exerting back pressure on the side of the piston receiving steam, thus slightly reducing cylinder power. Designing the exhaust ejector has become a specific science in which Chapelon, Giesl and Porta were successive masters, and it was largely responsible for spectacular improvements in thermal efficiency and a significant reduction in maintenance time[13] and pollution.[14] A similar system was used by some early gasoline/kerosene tractor manufacturers (Advance-Rumely/Hart-Parr)–the exhaust gas volume vented through a cooling tower meant that the steam exhaust helped draw more air past the radiator.

Running gear[edit]

Steam-cleaning the running gear of an "H" class locomotive, Chicago and North Western Railway, 1943
Running gear of steam locomotive

This includes the brake gear, wheel sets, axleboxes, springing and the motion that includes connecting rods and valve gear. The transmission of the power from the pistons to the rails and the behaviour of the locomotive as a vehicle, able to negotiate curves, points and irregularities in the track, is of paramount importance. Because reciprocating power has to be directly applied to the rail from 0 rpm upwards, this poses unique problems of adhesion of the driving wheels to the smooth rail surface. Adhesive weight is the portion of the locomotive's weight bearing on the driving wheels. This is made more effective if a pair of driving wheels is able to make the most of its axle load, i.e. its individual share of the adhesive weight. Locomotives with equalising beams connecting the ends of plate springs have often been deemed a complication but locomotives fitted with them have usually been less prone to loss of traction due to wheel-slip.

Locomotives with total adhesion, i.e. where all the wheels are coupled together, generally lack stability at speed. This makes desirable the inclusion of unpowered carrying wheels mounted on two-wheeled trucks or four-wheeled bogies centred by springs that help to guide the locomotive through curves. These usually take the weight of the cylinders in front or of the firebox at the rear end when the width of this exceeds that of the mainframes. For multiple coupled wheels on a rigid chassis a variety of systems for controlled side-play exist.

Railroads typically wanted a locomotive with fewer axles, to reduce the cost of maintenance. The number of axles required was dictated by the maximum axle loading of the railroad in question. A builder would typically add axles until the maximum weight on any one axle was acceptable to the railroad's maximum axle loading. A locomotive with a wheel arrangement of two lead axles, two drive axles, and one trailing axle was in actuality a high-speed machine. Two lead axles were necessary to have good tracking at high speeds. Two drive axles had a lower reciprocating mass than three, four, five or six coupled axles. They were thus able to turn very high speeds due to the lower reciprocating mass. A trailing axle was able to support a huge firebox, hence most locomotives with the wheel arrangement of 4-4-2 (American Type Atlantic) were called free steamers and were able to maintain steam pressure regardless of throttle setting.

Chassis[edit]

The chassis or locomotive frame is the principal structure onto which the boiler is mounted and which incorporates the various elements of the running gear. The boiler is rigidly mounted on a "saddle" beneath the smokebox and front of the boiler barrel, but the firebox at the rear is allowed to slide forward and back, to allow for expansion when hot.

European locomotives usually use "plate frames", where two vertical flat plates form the main chassis, with a variety of spacers and a buffer beam at each end to keep them apart. When inside cylinders are mounted between the frames, these are a single large casting that forms a major support to the frames. The axleboxes slide up and down to give some sprung suspension, against thickened webs attached to the frame, called "hornblocks".[citation needed]

American practice for many years was to use built-up bar frames, with the smokebox saddle/cylinder structure and drag beam integrated therein. In the 1920s, with the introduction of "superpower", the cast-steel locomotive bed became the norm, incorporating frames, spring hangers, motion brackets, smokebox saddle and cylinder blocks into a single complex, sturdy but heavy casting. André Chapelon developed a similar structure but of welded construction with around 30% saving in weight for the stillborn 2-10-4 locomotives, the construction of which was begun then abandoned in 1946.[citation needed]

Fuel and water[edit]

Water gauge. Here the water in the boiler is at the "top nut", higher than the normal maximum working level.

Generally, the largest locomotives are permanently coupled to a tender that carries the water and fuel. Often, locomotives working shorter distances do not have a tender and carry the fuel in a bunker, the water is carried in tanks placed next to the boiler either in 2 tanks alongside (pannier tank), one on top (saddle tank) or one underneath (well tank); these are called tank engines and usually have a 'T' suffix added to the Whyte notation, e.g., 0-6-0T.

The fuel used depended on what was economically available to the railway. In the UK and other parts of Europe, plentiful supplies of coal made this the obvious choice from the earliest days of the steam engine. Until 1870,[15] the majority of locomotives in the USA burnt wood but, as the Eastern forests were cleared, coal gradually became more important. Thereafter, coal became and remained the dominant fuel worldwide until the end of general use of steam locomotives. Bagasse, a waste by-product of the refining process, was burned in sugar cane farming operations. In the USA, the ready availability of oil made it a popular steam locomotive fuel after 1900 for the southwestern railroads, particularly the Southern Pacific. In Victoria, Australia after World War II, many steam locomotives were converted to heavy oil firing. German, Russian, Australian and British railways experimented using coal dust to fire locomotives.

A number of tourist lines and heritage locomotives in Switzerland, Argentina and Australia have been using light diesel-type oil.[16]

Water was supplied at stopping places and locomotive depots from a dedicated water tower connected to water cranes or gantries. In the UK, the USA and France, water troughs (US track pans) were provided on some main lines to allow locomotives to replenish their water supply without stopping. This was achieved by using a 'water scoop' fitted under the tender or the rear water tank in the case of a large tank engine; the fireman remotely lowered the scoop into the trough, the speed of the engine forced the water up into the tank, and the scoop was raised again once it was full.

"Water is an essential element in the operation of a steam locomotive"
Here a locomotive is "taking-on water"—having its tanks refilled using a water crane.

Water is an essential element in the operation of a steam locomotive; because as Swengel argued:

it has the highest specific heat of any common substance; that is more thermal energy is stored by heating water to a given temperature than would be stored by heating an equal mass of steel or copper to the same temperature. In addition, the property of vapourising (forming steam) stores additional energy without increasing the temperature... water is a very satisfactory medium for converting thermal energy of fuel into mechanical energy

Swengel went on to note that "at low temperature and relatively low boiler outputs" good water and regular boiler washout was an acceptable practise, even though such maintenance was high. As steam pressures increased, however, a problem of "foaming" or "priming" developed in the boiler, wherein dissolved solids in the water formed "tough-skinned bubbles" inside the boiler, which in turn were carried into the steam pipes and could blow off the cylinder heads. To overcome the problem, hot mineral concentrated water was deliberately wasted (blowing down) from the boiler from time to time. Higher steam pressures required more blowing down of water out of the boiler. Oxygen generated by boiling water attacks the boiler and with increased steam pressures the rate of rust (iron oxide) generated inside the boiler increases. One way to help overcome the problem was water treatment. Swengel suggested that the problems around water contributed to the interest in electrification of railways.[17]

In the 1970s, L.D. Porta developed a sophisticated heavy duty chemical water treatment (Porta Treatment) that not only keeps the inside of the boiler clean and prevents corrosion, but modifies the foam in such a way as to form a compact "blanket" on the water surface that filters the steam as it is produced, keeping it pure and preventing carry-over into the cylinders of water and suspended abrasive matter.[18][19]

Crew[edit]

A steam locomotive is normally controlled from the boiler's backhead and the crew is usually protected from the elements by a cab. A crew of at least two people is normally required to operate a steam locomotive. One, the train driver, is responsible for controlling the locomotive's starting, stopping and speed, and the fireman is responsible maintaining the fire, regulating steam pressure, and monitoring boiler and tender water levels. Due to the historical loss of operational infrastructure and staffing, preserved steam locomotives operating on the mainline will often have a support crew travelling with the train.

Fittings and appliances[edit]

Further information: Category:locomotive parts

All locomotives are fitted with a variety of appliances. Some of these relate directly to the operation of the steam engine; while others are for signalling, train control or other purposes. In the United States the Federal Railroad Administration mandated the use of certain appliances over the years in response to safety concerns. The most typical appliances are as follows:

Steam pumps and injectors[edit]

Water (feedwater) must be delivered to the boiler to replace that which is exhausted as steam after delivering a working stroke to the pistons. As the boiler is under pressure during operation, feedwater must be forced into the boiler at a pressure that is greater than the steam pressure, necessitating the use of some sort of pump. Early engines used pumps driven by the motion of the pistons (axle pumps). Later steam injectors replaced the pump, while some engines use turbopumps. Standard practice evolved to use two independent systems for feeding water to the boiler. Vertical glass tubes, known as water gauges or water glasses, show the level of water in the boiler and are carefully monitored at all times while the boiler is being fired.

Boiler lagging[edit]

Large amounts of heat are wasted if a boiler is not insulated. Early locomotives used shaped wooden battens fitted lengthways along the boiler barrel and held in place by metal bands. Improved insulating methods included: applying a thick paste containing a porous mineral, such as kieselgur, or shaped blocks of insulating compound such as magnesia blocks[20] were attached. In the latter days of steam, "mattresses" of stitched asbestos cloth were fixed stuffed with asbestos fibre (but on separators so as not quite to touch the boiler); however in most countries, asbestos is nowadays banned for health reasons. The most common modern day material is glass wool, or wrappings of aluminium foil.

The lagging is protected by a close-fitted sheet-metal casing[21] known as boiler clothing or cleading.

Effective lagging is particularly important for fireless locomotives; however in recent times under the influence of L.D. Porta, "exaggerated" insulation has been practised for all types of locomotive on all surfaces liable to dissipate heat, such as cylinder ends and facings between the cylinders and the mainframes. This considerably reduces engine warmup time with marked increase in overall efficiency.

Safety valves[edit]

Main article: Safety valve
The boiler safety valves lifting on 60163 Tornado creating a false smoke trail

Early locomotives were fitted with a valve controlled by a weight suspended from the end of a lever, the steam outlet being stopped by a cone-shaped valve. As there was nothing to prevent the weighted lever from bouncing when the locomotive ran over irregularities in the track, thus wasting steam, the weight was replaced by a more stable spring-loaded column, often supplied by Salter, a well-known spring scale manufacturer. The danger of all these devices was that the driving crew could be tempted to add weight to the arm to increase pressure. Most boilers were from early times fitted with a tamper-proof "lockup" direct-loaded ball valve protected by a cowl. In the late 1850s, John Ramsbottom introduced a safety valve that became popular in Britain during the latter part of the 19th century. Not only was this valve tamper-proof, but tampering by the driver could only have the effect of easing pressure. George Richardson's safety valve was an American invention introduced in 1875[22] and was so designed as to release the steam only at the moment when the pressure attained the maximum permitted. This type of valve is in almost universal use at present. Britain's Great Western Railway was a notable exception to this rule retaining the direct loaded type until the end of its separate existence because it was considered that such a valve lost less pressure between opening and closing.

Pressure gauge[edit]

Main article: Pressure measurement
Pressure gauges on Blackmore Vale. The right-hand one shows boiler pressure, the one on the left steam chest pressure

The earliest locomotives did not show the pressure of steam in the boiler, but it was possible to estimate this by the position of the safety valve arm which often extended onto the firebox back plate; gradations marked on the spring column gave a rough indication of the actual pressure. The promoters of the Rainhill trials urged that each contender have a proper mechanism for reading the boiler pressure and Stephenson devised a nine-foot vertical tube of mercury with a sight-glass at the top, mounted alongside the chimney, for the Rocket. The Bourdon tube gauge, in which the pressure straightens an oval-section, coiled tube of brass or bronze connected to a pointer, was introduced in 1849 and quickly gained acceptance. This is the device used today.[23] Some locomotives have an additional pressure gauge in the steam chest. This helps the driver avoid wheel-slip at startup, by warning if the regulator opening is too great.

Spark arrestors and smokeboxes[edit]

Spark arrestor and self-cleaning smokebox

Main articles: Spark arrestor and smokebox
Typical self-cleaning smokebox design

Wood-burners emit large quantities of flying sparks which necessitate an efficient spark arresting device generally housed in the smokestack. Many types were fitted,[24] the most common early type being the Bonnet stack that incorporated a cone-shaped deflector placed before the mouth of the chimney pipe plus a wire screen covering the wide stack exit; more efficient was the Radley and Hunter centrifugal type patented in 1850, (generally known as the diamond stack) incorporating baffles so orientated as to induce a swirl effect in the chamber that encouraged the embers to burn out and fall to the bottom as ash. In the self-cleaning smokebox the opposite effect was achieved: by allowing the flue gasses to strike a series of deflector plates, angled in such a way that the blast was not impaired, the larger particles were broken into small pieces that would be ejected with the blast, rather than settle in the bottom of the smokebox to be removed by hand at the end of the run. As with the arrestor, a screen was incorporated to retain any large embers.[25]

Locomotives of the British Railways standard classes fitted with self-cleaning smokeboxes were identified by a small cast oval plate marked "S.C.", fitted at the bottom of the smokebox door. These engines required different disposal procedures and the 'S.C.' plate highlighted this need to depot staff.

Stokers[edit]

Main article: Mechanical stoker

A factor that limits locomotive performance is the rate at which fuel is fed into the fire. In the early 20th century some locomotives became so large that the fireman could not shovel coal fast enough.[21] In the United States, various steam-powered mechanical stokers became standard equipment and were adopted and used elsewhere including Australia and South Africa.

Feedwater heating[edit]

Introducing cold water into a boiler reduces power, and from the 1920s a variety of heaters were incorporated. The most common type for locomotives was the exhaust steam feedwater heater that piped some of the exhaust through small tanks mounted on top of the boiler or smokebox or else into the tender tank; the warm water then had to be delivered to the boiler by a small auxiliary steam pump. The rare economiser type differed in that it extracted residual heat from the exhaust gases. An example of this is the pre-heater drum(s) found on the Franco-Crosti boiler.

The use of live steam and exhaust steam injectors also assists in the pre-heating of boiler feed water to a small degree, though there is no efficiency advantage to live steam injectors. Such pre-heating also reduces the thermal shock that a boiler might experience when cold water is introduced directly. This is further helped by the top feed where water is introduced to the highest part of the boiler and made to trickle over a series of trays. G.J. Churchward fitted this arrangement to the high end of his domeless coned boilers. Other British lines such as the LBSCR fitted a few locomotives with the top feed inside a separate dome forward of the main one.

Condensers and water re-supply[edit]

Watering a steam locomotive
South African Class 25 condensing locomotive.

Steam locomotives consume vast quantities of water because they operate on an open cycle, expelling their steam immediately after a single use rather than recycling it in a closed loop as stationary and marine steam engines do. Water was a constant logistical problem, and for use in some desert areas condensing engines were devised. These engines had huge radiators in their tenders and instead of exhausting steam out of the funnel it was captured and passed back to the tender and condensed. The cylinder lubricating oil was removed from the exhausted steam to avoid a phenomenon known as priming, a condition caused by foaming in the boiler which would allow water to be carried into the cylinders causing damage because of its incompressibility. The most notable engines employing condensers (Class 25, the "puffers which never puff"[26]) worked across the Karoo desert of South Africa, from the 1950 until the 1980s.

Some British and American locomotives were equipped with scoops which collected water from "water troughs" (US: "track pans") while in motion, thus avoiding stops for water. In the U.S., small communities often did not have refilling facilities. During the early days of railroading, the crew simply stopped next to a stream and filled the tender using leather buckets. This was known as “jerking water” and led to the term "jerkwater towns" (meaning a small town, a term which today is considered derisive).[27] In Australia and South Africa, locomotives in drier regions operated with large oversized tenders and some even had an additional water wagon, sometimes called a "canteen" or in Australia (particularly in New South Wales) a "water gin".

Steam locomotives working on underground railways (such as London's Metropolitan Railway) were fitted with condensing apparatus to prevent steam from escaping into the railway tunnels. These were still being used between King's Cross and Moorgate into the early 1960s.

Braking[edit]

See also: Railway brake

Locomotives have their own braking system, independent from the rest of the train. Locomotive brakes employ large shoes which press against the driving wheel treads. With the advent of air brakes, a separate system also allowed the driver to control the brakes on all cars. These systems require steam-powered compressors, which are mounted on the side of the boiler or on the smokebox front. Almost all of these compressors were of the Westinghouse single-stage or cross-compound variety. Such systems operated in the United States, Canada, Australia and New Zealand.

An alternative to the air brake is the vacuum brake, in which a steam-operated ejector is mounted on the engine instead of the air pump, to create vacuum and release the brakes. A secondary ejector or crosshead vacuum pump is used to maintain the vacuum in the system against the small leaks in the pipe connections between carriages and wagons. Vacuum systems existed on British, Indian, Western Australian and South African railway networks.

Steam locomotives are nearly always fitted with sandboxes from which sand can be delivered to the rails to improve traction and braking in wet or icy weather. On American locomotives the sandboxes, or sand domes, are usually mounted on top of the boiler. In Britain, the limited loading gauge precludes this, so the sandboxes are mounted just above, or just below, the running plate.

Lubrication[edit]

See also: Lubrication
“Wakefield” brand displacement lubricator mounted on a locomotive boiler backplate. Through the right-hand sight glass a drip of oil (travelling upwards through water) can be seen.

The pistons and valves on the earliest locomotives were lubricated by the enginemen dropping a lump of tallow down the blast pipe.[28]

As speeds and distances increased, mechanisms were developed that injected thick mineral oil into the steam supply. The first, a displacement lubricator, mounted in the cab, uses a controlled stream of steam condensing into a sealed container of oil. Water from the condensed steam displaces the oil into pipes. The apparatus is usually fitted with sight-glasses to confirm the rate of supply. A later method uses a mechanical pump worked from one of the crossheads. In both cases, the supply of oil is proportional to the speed of the locomotive.

Big-end bearing (with connecting rod and coupling rod) of Blackmoor Vale showing pierced cork stoppers to oil reservoirs

Lubricating the frame components (axle bearings, horn blocks and bogie pivots) depends on capillary action: trimmings of worsted yarn are trailed from oil reservoirs into pipes leading to the respective component.[29] The rate of oil supplied is controlled by the size of the bundle of yarn and not the speed of the locomotive, so it is necessary to remove the trimmings (which are mounted on wire) when stationary. However, at regular stops (such as a terminating station platform) oil finding its way onto the track can still be a problem.

Crank pin and crosshead bearings carry small cup-shaped reservoirs for oil. These have feed pipes to the bearing surface that start above the normal fill level, or are kept closed by a loose-fitting pin, so that only when the locomotive is in motion does oil enter. In United Kingdom practice the cups are closed with simple corks, but these have a piece of porous cane pushed through them to admit air. It is customary for a small capsule of pungent oil (aniseed or garlic) to be incorporated in the bearing metal to warn if the lubrication fails and excess heating or wear occurs.[30]

Blower[edit]

When the locomotive is running under power, a draught on the fire is created by the exhaust steam directed up the chimney by the blastpipe. Without draught, the fire will quickly die down and steam pressure will fall. When the locomotive is stopped, or coasting with the regulator closed, there is no exhaust steam to create a draught, so the draught is maintained by means of the blower. This is a ring placed either around the base of the chimney, or around the blast pipe orifice, containing several small steam nozzles directed up the chimney. These nozzles are fed with steam directly from the boiler, controlled by the blower valve. When the regulator is open, the blower valve is closed; when the driver intends to close the regulator, he will first open the blower valve. It is important that the blower be opened before the regulator is closed, since without draught on the fire, there may be backdraught—air from the atmosphere blows down the chimney, causing the flow of hot gases through the boiler tubes to be reversed, with the fire itself being blown through the firehole onto the footplate, with serious consequences for the crew. The risk of backdraught is higher when the locomotive enters a tunnel because of the pressure shock. The blower is also used to create draught when steam is being raised at the start of the locomotive's duty; at any time when the driver needs to increase the draught on the fire; and to clear smoke from the driver's line of vision.[31]

Buffers[edit]

In British and European (except former Soviet Union countries) practice, the locomotive usually had buffers at each end to absorb compressive loads ("buffets"[32]). The tensional load of drawing the train (draft force) is carried by the coupling system. Together these control slack between the locomotive and train, absorb minor impacts and provide a bearing point for pushing movements.

In American practice all of the forces between the locomotive and cars are handled through the coupler — particularly with types of the Janney coupler long standard on American railroad rolling stock — and its associated draft gear, which allows some limited slack movement. Small dimples called "poling pockets" at the front and rear corners of the locomotive allowed cars to be pushed on an adjacent track using a pole braced between the locomotive and the cars.[33] In Britain and Europe, American style 'buckeye' and other couplers that also handle forces between items of rolling stock have become increasingly popular.

Pilots[edit]

A pilot was usually fixed to the front end of locomotives, although in European and a few other railway systems, such as New South Wales, they were considered unnecessary. Plough-shaped, and called cow catchers, they were quite large and were designed to remove obstacles from the track such as cattle, bison, other animals or tree limbs. Though unable to "catch" stray cattle these distinctive items remained on locomotives until the end of steam. Switching engines usually replaced the pilot with small steps, known as footboards. Many systems used the pilot and other design features to produce a distinctive appearance.

Headlights[edit]

Preserved Great Western Railway locomotive Bradley Manor, with two oil lamps signifying an express passenger service, and between them a high-intensity electric lamp, added to comply with modern safety standards for mainline running.

When night operations began, railway companies in some countries equipped their locomotives with lights to allow the driver to see what lay ahead of the train or to enable others to see the locomotive. Originally headlights were oil or acetylene lamps, but when electric arc lamps became available in the late 1880s, they quickly replaced the older types.

Britain did not adopt bright headlights as they would affect night-adapted vision and so could mask the low-intensity oil lamps used in the semaphore signals and at each end of trains, increasing the danger of missing signals especially on busy tracks. In any case, trains' stopping distances were normally much greater than the range of headlights, and the railways were well-signalled and fully fenced to prevent livestock and people from straying onto them. Thus low-intensity oil lamps continued to be used, positioned on the front of locomotives to indicate the class of each train. Four 'lamp irons' were provided (brackets on which to place the lamps): one below the chimney and three evenly spaced across the top of the buffer beam. The exception to this was the Southern Railway and its constituents, who added an extra lamp iron each side of the smokebox, and the arrangement of lamps (or in daylight, white circular plates) told railway staff the origin and destination of the train. (In all cases, equivalent lamp irons were also provided on the rear of the locomotive or tender for when the locomotive was running tender- or bunker-first.)

In some countries heritage steam operation continues on the national network. Some railway authorities have mandated powerful headlights on at all times, including during daylight. This was to further inform the public or track workers of any active trains.

Bells and whistles[edit]

Main article: Train whistle

Locomotives used bells and steam whistles from earliest days. In the United States, India and Canada, bells warned of a train in motion. In Britain, where all lines are by law fenced throughout,[34] bells were only a requirement on railways running on a road (i.e., not fenced off), for example a tramway along the side of the road or in a dockyard. Consequently only a minority of locomotives in the UK carried bells. Whistles are used to signal personnel and give warnings. Depending on the terrain the locomotive was being used in the whistle could be designed for long distance warning of impending arrival, or more for localised use.

Early bells and whistles were sounded through pull-string cords and levers. Automatic bell ringers came into widespread use in the U.S. after 1910.[35]

Automatic control[edit]

This is a typical AWS Sunflower indicator. the Sunflower indicator can show a black disk or a yellow and black "exploding" disk.

From early in the 20th century operating companies in such countries as Germany and Britain began to fit locomotives with in-cab signalling (AWS) which automatically applied the brakes when a signal was passed at "caution". In Britain these became mandatory in 1956. In the United States, the Pennsylvania Railroad also fitted their locomotives with such devices.

Booster engines[edit]

In the United States and Australia the trailing truck was often equipped with an auxiliary steam engine which provided extra power for starting. This booster engine was set to cut out automatically at a certain speed. On the narrow gauged New Zealand railway system, six Kb 4-8-4 locomotives had boosters, the only 3 ft 6 in (1,067 mm) gauge engines in the world to have such equipment.

Variations[edit]

Numerous variations to the simple locomotive occurred as railways attempted to improve efficiency and performance.

Cylinders[edit]

Early steam locomotives had two cylinders, one either side, and this practice persisted as the simplest arrangement. The cylinders could be mounted between the main frames (known as 'inside' cylinders), or mounted outside the frames and driving wheels ('outside' cylinders). Inside cylinders are driven by cranks built into the driving axle; outside cylinders are driven by cranks on extensions to the driving axles.

Later designs employed three or four cylinders, mounted both inside and outside the frames, for a more even power cycle and greater power output.[36] This was at the expense of more complicated valve gear and increased maintenance requirements. In some cases the third cylinder was added 'inside' simply to allow for smaller diameter outside cylinders, and hence reduce the width of the locomotive for use on lines with a restricted loading gauge, for example the SR K1 and U1 classes.

Most British express passenger locomotives built from about 1930 to 1950 were 4-6-0 or 4-6-2 types with three or four cylinders (e.g., GWR 6000 Class, LMS Coronation Class, SR Merchant Navy Class, LNER Gresley Class A3). From 1951, all but one of the 999 new British Rail standard class steam locomotives of all types from express passenger and heavy freight to smaller mixed traffic tank locomotives used 2-cylinder configurations for easier maintenance.

Valve gear[edit]

Main article: Valve gear

Numerous technological advances improved the steam engine. Early locomotives used simple valve gear that gave full power in either forward or reverse.[23] Soon Stephenson valve gear allowed the driver to control cut-off; this was largely superseded by Walschaerts valve gear and similar patterns. Early locomotive designs using slide valves and outside admission were relatively easy to construct, but inefficient and prone to wear.[23] Eventually, slide valves were superseded by inside admission piston valves, though there were attempts to apply poppet valves (common by then on stationary engines) in the 20th century. Stephenson valve gear was generally placed within the frame and was difficult to access for maintenance; later patterns applied outside the frame, were readily visible and maintained.

Compounding[edit]

Main article: Compound locomotive
U-127 Lenin's Locomotive a 4-6-0 oil burning De Glehn compound locomotive, at the Museum of the Moscow Railway at Paveletsky Rail Terminal

From 1876, compound locomotives came on the scene, which used the engine's steam twice. There were many compound locomotives especially where long periods of continuous efforts were needed. Compounding was an essential ingredient of the quantum leap in power achieved by André Chapelon's rebuilds from 1929. A common application was to articulated locomotives, the most common being that of Anatole Mallet in which the high-pressure stage was attached directly to the boiler frame; in front of this was pivoted a low-pressure engine on its own frame, taking the exhaust from the rear engine.[37]

Articulated locomotives[edit]

More powerful locomotives also tend to be longer, but long, rigid-framed designs are impractical for the tight curves frequently found on narrow gauge railways. Various designs of articulated locomotives were developed to overcome this problem. The Mallet and the Garratt were the two most popular, both using a single boiler and two engines (sets of cylinders and driving wheels)—the Garratt having two power bogies, the Mallet having one. There were also a few examples of "triplex" locomotives that had a third engine under the tender. Both the front and tender engines were low-pressure compounded, though they could be operated simple (high-pressure) for starting off. Other, less common, variations included the Fairlie locomotive, which had two boilers back-to-back on a common frame, with two separate power bogies.

Duplex types[edit]

Duplex locomotives with two engines in one rigid frame were also tried, but were not notably successful. For example, the 4-4-4-4 Pennsylvania Railroad's T1 class, designed for very fast running, suffered recurring and ultimately unfixable slippage problems throughout their careers.[38]

Geared locomotives[edit]

For uses where a high starting torque and low speed were required, the conventional direct drive approach was inadequate. "Geared" steam locomotives, such as the Shay, the Climax and the Heisler, were developed to meet this need on industrial, logging, mine and quarry railways. The common feature of these three types was the provision of reduction gearing and a drive shaft between the crankshaft and the driving axles. This arrangement allowed the engine to run at a much higher speed than the driving wheels, compared to the conventional design, where the ratio is 1:1.

Cab forward[edit]

In the United States on the Southern Pacific Railroad a series of cab forward locomotives had the cab and the firebox at the front of the locomotive and the tender behind the smokebox, so that the engine appeared to run backwards. This was only possible by using oil-firing. Southern Pacific selected this design to provide air free of smoke for the engine driver to breathe as they went through the SP's numerous mountain tunnels and snow sheds. Another variation was the Camelback locomotive with the cab halfway along the boiler. In England, Oliver Bulleid developed the SR Leader class locomotive during the nationalisation process in the late 1940s. The locomotive was heavily tested but several design faults (like coal firing and sleeve valves) meant this locomotive and the other part-built locomotives were scrapped. The cab-forward design was taken by Bulleid to Ireland when he moved to after nationalisation where he developed the 'turfburner'. This locomotive was more successful but was scrapped with the dieselisation of the Irish railways.

The only preserved cab forward locomotive is Southern Pacific 4294 in Sacramento, California, US.

In France, the three Heilmann locomotives were a cab forward design.

Steam turbines[edit]

Steam turbines were one of the experiments in improving the operation and efficiency of steam locomotives. Experiments with steam turbines using direct-drive and electrical transmissions, in different countries, proved mostly unsuccessful.[21] The London, Midland and Scottish Railway also built Turbomotive, a largely successful attempt to prove the efficiency of steam turbines.[21] Had it not been for the outbreak of World War II, more may have been built. The Turbomotive ran from 1935 to 1949, when it was rebuilt into a conventional locomotive because replacement of many parts was required, an uneconomical proposition for a 'one-off' locomotive. In the United States the Union Pacific, Chesapeake and Ohio and Norfolk & Western (N&W) railways all built turbine-electric locomotives. The Pennsylvania Railroad (PRR) also built turbine locos but with a direct-drive gearbox. However, all designs failed due to dust, vibration, design flaws or inefficiency at lower speeds. The last one in service was the N&W's, retired in January 1958. The only truly successful design was the TGOJ MT3, used for hauling iron ore from Grängesberg to the ports of Oxelösund. Technically well-working, only three were built. Two of them are saved in working order at museums in Sweden.

Hybrid power[edit]

Mixed power locomotives, utilising steam and diesel propulsion, have been produced in Russia, Britain and Italy.

Under severely unusual conditions (lack of coal, plenty of hydroelectricity) some locomotives in Switzerland were modified to use electricity to heat the boiler, making them electric-steam locomotives.[39]

Fireless locomotive[edit]

Main article: Fireless locomotive
Fireless locomotive

In a fireless locomotive the boiler is replaced by a steam accumulator which is charged with steam (actually water at high temperature well above the boiling point, 212 °F/100 °C) from a stationary boiler. Fireless locomotives were used where there was a high fire risk (e.g., in oil refineries), where cleanliness was important (e.g., in food factories) or where steam is readily available such as in processes where steam is either a by-product or is cheaply available e.g. paper mills and power stations. The water vessel ("boiler") is heavily insulated as is a fired locomotive. Until all the water has boiled away, the steam pressure does not drop except as the temperature drops. Another class of fireless locomotive is a compressed air locomotive.

Steam-electric locomotive[edit]

Heilmann locomotive No. 8001, Chemins de Fer de l'Ouest
Main article: Heilmann locomotive

A steam-electric locomotive is similar in concept to a diesel-electric locomotive, except that a steam engine is used to drive a generator instead of a diesel engine. Three such locomotives were built by the French engineer Jean Jacques Heilmann in the 1890s.

Manufacture[edit]

Most manufactured classes[edit]

The largest single class of steam locomotive in the world is the 0-10-0 Russian locomotive class E steam locomotive with around 11,000 manufactured both in Russia and other countries such as Czechoslovakia, Germany, Sweden, Hungary and Poland. The Russian locomotive class O numbered 9,129 locomotives built between 1890 and 1928. The German DRB Class 52 2-10-0 Kriegslok which consisted of approximate 7,000 units. The British GWR 5700 class numbered about 863 units. The DX class of the London and North Western Railway numbered 943 units, including 86 engines built for the Lancashire and Yorkshire Railway.[40]

United Kingdom[edit]

Great Western Railway No. 6833 Calcot Grange, a 4-6-0 Grange class steam locomotive, at Bristol Temple Meads railway station, Bristol, England. Note the Belpaire (square-topped) firebox.

Before the 1923 Grouping Act, the picture in the UK was mixed. The larger railway companies built locomotives in their own workshops but the smaller ones and industrial concerns ordered them from outside builders. A large market for outside builders was abroad because of the home-build policy exercised by the main railway companies. An example of a pre grouping works was the one at Melton Constable that maintained and built some of the locomotives for the Midland and Great Northern Joint Railway. Other works included one at Boston (an early GNR building) and Horwich works.

Between 1923 and 1947, the "Big Four" railway companies (the Great Western Railway, the London, Midland and Scottish Railway, the London and North Eastern Railway and the Southern Railway) all built most of their own locomotives. Generally speaking, they only bought locomotives from outside builders when their own works were fully occupied (or as a result of government-mandated standardisation during wartime).

From 1948, British Railways allowed the former "Big Four" companies (now designated as "Regions") to continue to build their own designs, but also created a range of standard locomotives which supposedly combined the best features from each region. Although a policy of "dieselisation" was adopted in 1955, BR continued to build new steam locomotives until 1960 (the last being named Evening Star).

Some independent manufacturers produced steam locomotives for a few more years, the last British-built industrial steam locomotive being constructed by Hunslet in 1971. Since then, a few specialised manufacturers have continued to produce small locomotives for narrow gauge and miniature railways, but as the prime market for these is the tourist and heritage railway sector, the demand for such locomotives is limited. In November 2008, a new build main line steam locomotive, the 60163 Tornado, was tested on UK mainlines for eventual charter and tour use.

Australia[edit]

The 200th steam locomotive built by Clyde Engineering (TF 1164) from the Powerhouse Museum collection

In Australia, Clyde Engineering of Sydney and also the Eveleigh Workshops built steam locomotives for the New South Wales Government Railways. These include the C38 class 4-6-2; the first five were built at Clyde with streamlining, the other 25 locomotives were built at Eveleigh (13) in Sydney, and Cardiff Workshops (12) near Newcastle. In Queensland, steam locomotives were locally constructed by Walkers. Similarly the South Australian state government railways also manufactured steam locomotives locally at Islington in Adelaide. The Victorian Railways constructed most of their locomotives at their Newport Workshops and Bendigo while in the early days locomotives were built at the Phoenix Foundry in Ballarat. Locomotives constructed at the Newport shops ranged from the nA class 2-6-2T built for the narrow gauge, up to the H class 4-8-4, the largest conventional locomotive ever to operate in Australia, which weighed 260 tons. However, the title of largest locomotive in Australia goes to the 263-ton NSWGR AD60 class 4-8-4+4-8-4 Garratt,[41] which were built by Beyer-Peacock in the United Kingdom. Most steam locomotives used in Western Australia were built in the United Kingdom, though some examples were designed and built locally at the Western Australian Government Railways' Midland Railway Workshops. The 10 WAGR S class locomotives (introduced in 1943) were the only class of steam locomotive to be wholly conceived, designed and built in Western Australia,[42] while the Midland workshops notably participated in the Australia-wide construction program of Australian Standard Garratts - these wartime locomotives were built at Midland in Western Australia, Clyde Engineering in New South Wales, Newport in Victoria and Islington in South Australia and saw at least some service in all Australian states.[42]

Sweden[edit]

In the 19th and early 20th centuries, most Swedish steam locomotives were manufactured in Britain. But later on, most steam locomotives were built by local factories including NOHAB in Trollhättan and ASJ in Falun. One of the most successful types was the class "B" (4-6-0), inspired by the Prussian class P8. Many of the Swedish steam locomotives were preserved during the Cold War in case of war. During the 1990s, these steam locomotives were sold to non-profit associations or abroad, which is why the Swedish class B, class S (2-6-4) and class E2 (2-8-0) locomotives can now be seen in Britain, the Netherlands, Germany and Canada.

United States[edit]

California Western Railroad #45 (builder #58045), Built by Baldwin in 1924, number 45 is a 2-8-2 "Mikado" locomotive. It is still in use today on the Skunk Train

Railroad locomotive engines in the United States have nearly always been built in and for United States railroads with very few imports, except in the earliest days. This is because of the basic differences of markets in the United States which initially had many small markets located large distances apart, very different from Europe's much higher density markets. Locomotives that were cheap and rugged and could go over large distances over cheaply built and maintained tracks were the early requirements. Once the manufacture of engines was established on a wide scale there was very little advantage to buying an engine somewhere else that would have to be customized anyway to fit the local requirements and track conditions. Improvements in engine design of both European and U.S. origin could be and were incorporated by manufacturers when they could be justified in a generally very conservative and slow changing market. With the notable exception of the USRA standard locomotives, set during World War I, in the United States, steam locomotive manufacture was always semi-customised. Railroads ordered locomotives tailored to their specific requirements, though basic design features were always present. Railroads developed some specific characteristics; for example, the Pennsylvania Railroad and the Great Northern had a preference for the Belpaire firebox,.[43] In the United States, large-scale manufacturers constructed locomotives for nearly all rail companies, although nearly all major railroads had shops capable of heavy repairs and some railroads (for example, the Norfolk and Western Railway and the Pennsylvania Railroad, which had two erecting shops) constructed complete locomotives in their own shops.[citation needed] Companies manufacturing locomotives in the US included Baldwin Locomotive Works, American Locomotive Company (Alco), and Lima Locomotive Works.

Steam locomotives required regular, and compared to a diesel-electric engine, frequent service and overhaul (often at government-regulated intervals in Europe and the U.S.) Many alterations and upgrades regularly occurred during overhauls. New appliances were added, unsatisfactory features removed, cylinders improved or replaced. Almost any part of the locomotive, including boilers, was replaced or upgraded. When the service or upgrades got too expensive the locomotive was traded off or retired.[citation needed] On the Baltimore and Ohio Railroad two 2-10-2 locomotives were dismantled; the boilers were placed onto two new Class T 4-8-2 locomotives and the residue wheel machinery made a pair of Class U 0-10-0 switchers with new boilers. Union Pacific's fleet of 3-cylinder 4-10-2 engines were converted into two-cylinder engines in 1942, because of high maintenance problems.

Categorisation[edit]

The Gov. Stanford, a 4-4-0 (in Whyte notation) locomotive typical of 19th-century American practice

Steam locomotives are categorised by their wheel arrangement. The two dominant systems for this are the Whyte notation and UIC classification.

The Whyte notation, used in most English speaking and Commonwealth countries, represents each set of wheels with a number. These numbers typically represented the number of un-powered leading wheels, followed by the number of driving wheels (sometimes in several groups), followed by the number of un-powered trailing wheels. For example, a yard engine with only 4 drive wheels would be shown as a "0-4-0" wheel arrangement. A locomotive with a 4 wheel leading truck, followed by 6 drive wheels, and a 2 wheel trailing truck, would be classed as a "4-6-2". Different arrangements were given names which usually reflect the first usage of the arrangement; for instance the "Santa Fe" type (2-10-2) is so called because the first examples were built for the Atchison, Topeka and Santa Fe Railway. These names were informally given and varied according to region and even politics.

The UIC classification is used mostly in European countries apart from the United Kingdom. It designates consecutive pairs of wheels (informally "axles") with a number for non-driving wheels and a capital letter for driving wheels (A=1, B=2, etc.) So a Whyte 4-6-2 designation would be an equivalent to a 2-C-1 UIC designation.

On many railroads, locomotives were organised into classes. These broadly represented locomotives which could be substituted for each other in service, but most commonly a class represented a single design. As a rule classes were assigned some sort of code, generally based on the wheel arrangement. Classes also commonly acquired nicknames, such as 'Pugs', representing notable (and sometimes uncomplimentary) features of the locomotives.[44][45]

Performance[edit]

Measurement[edit]

In the steam locomotive era, two measures of locomotive performance were generally applied. At first, locomotives were rated by tractive effort This can be roughly calculated by multiplying the total piston area by 85% of the boiler pressure (a rule of thumb reflecting the slightly lower pressure in the steam chest above the cylinder) and dividing by the ratio of the driver diameter over the piston stroke. However, the precise formula is:

Tractive Effort is defined as the average force developed during one revolution of the driving wheels at the rail head.[17] This is expressed as:

t = \frac {cPd^2s} {D}.

where d is bore of cylinder (diameter) in inches, s is cylinder stroke, in inches, P is boiler pressure in pound per square inch, D is driving wheel diameter in inches, c is a factor that depends on the effective cut-off.[46] In the U.S. "c" is usually set at 0.85, but lower on engines that have maximum cutoff limited to 50–75%.

It is critical to appreciate the use of the term 'average', as not all effort is constant during the one revolution of the drivers for at some points of the cycle only one piston is exerting turning moment and at other points both pistons are working. Not all boilers deliver full power at starting and also the tractive effort decreases as the rotating speed increases.[17]

Tractive effort is a measure of the heaviest load a locomotive can start or haul at very low speed over the ruling grade in a given territory.[17]

However, as the pressure grew to run faster goods and heavier passenger trains, tractive effort was seen to be an inadequate measure of performance because it did not take into account speed.

Therefore in the 20th century, locomotives began to be rated by power output. A variety of calculations and formulas were applied, but in general railways used dynamometer cars to measure tractive force at speed in actual road testing.

British railway companies have been reluctant to disclose figures for drawbar horsepower and have usually relied on continuous tractive effort instead.

Relation to wheel arrangement[edit]

Whyte classification is connected to locomotive performance, but through a somewhat circuitous path. Given adequate proportions of the rest of the locomotive, power output is determined by the size of the fire, and for a bituminous coal-fuelled locomotive, this is determined by the grate area. Modern non-compound locomotives are typically able to produce about 40 drawbar horsepower per square foot of grate. Tractive force, as noted earlier, is largely determined by the boiler pressure, the cylinder proportions, and the size of the driving wheels. However, it is also limited by the weight on the driving wheels (termed "adhesive weight"), which needs to be at least four times the tractive effort.[21]

The weight of the locomotive is roughly proportional to the power output; the number of axles required is determined by this weight divided by the axleload limit for the trackage where the locomotive is to be used. The number of driving wheels is derived from the adhesive weight in the same manner, leaving the remaining axles to be accounted for by the leading and trailing bogies.[21] Passenger locomotives conventionally had two-axle leading bogies for better guidance at speed; on the other hand, the vast increase in the size of the grate and firebox in the 20th century meant that a trailing bogie was called upon to provide support. On the European continent, some use was made of several variants of the Bissel bogie in which the swivelling movement of a single axle truck controls the lateral displacement of the front driving axle (and in one case the second axle too). This was mostly applied to 8-coupled express and mixed traffic locomotives and considerably improved their ability to negotiate curves whilst restricting overall locomotive wheelbase and maximising adhesion weight.

As a rule, "shunting engines" (US "switching engines") omitted leading and trailing bogies, both to maximise tractive effort available and to reduce wheelbase. Speed was unimportant; making the smallest engine (and therefore smallest fuel consumption) for the tractive effort paramount. Driving wheels were small and usually supported the firebox as well as the main section of the boiler. Banking engines (US "helper engines") tended to follow the principles of shunting engines, except that the wheelbase limitation did not apply, so banking engines tended to have more driving wheels. In the U.S., this process eventually resulted in the Mallet type with its many driven wheels, and these tended to acquire leading and then trailing bogies as guidance of the engine became more of an issue.

As locomotive types began to diverge in the late 19th century, freight engine designs at first emphasised tractive effort, whereas those for passenger engines emphasised speed. Over time, freight locomotive size increased, and the overall number of axles increased accordingly; the leading bogie was usually a single axle, but a trailing truck was added to larger locomotives to support a larger firebox that could no longer fit between or above the driving wheels. Passenger locomotives had leading bogies with two axles, fewer driving axles, and very large driving wheels in order to limit the speed at which the reciprocating parts had to move.

In the 1920s the focus in the United States turned to horsepower, epitomised by the "super power" concept promoted by the Lima Locomotive Works, although tractive effort was still the prime consideration after World War I to the end of steam. Goods trains were to run faster; passenger locomotives needed to pull heavier loads at speed. In essence, the size of grate and firebox increased without changes to the remainder of the locomotive, requiring the addition of a second axle to the trailing truck. Freight 2-8-2s became 2-8-4s while 2-10-2s became 2-10-4s. Similarly, passenger 4-6-2s became 4-6-4s. In the United States this led to a convergence on the dual-purpose 4-8-4 and the 4-6-6-4 articulated configuration, which was used for both freight and passenger service.[47] Mallet locomotives went through a similar transformation and evolved from bank engines into huge mainline locomotives with gargantuan fireboxes; their driving wheels being increased in size in order to allow faster running.

The end of steam in general use[edit]

The introduction of electric locomotives at the turn of the 20th century and later diesel-electric locomotives spelled the beginning of the end for steam locomotives, although that end was long in coming.[48] As diesel power, more especially with electric transmission, became more reliable in the 1930s it gained a foothold in North America.[49] The full changeover took place there during the 1950s. In continental Europe large-scale electrification had displaced steam power by the 1970s. Steam had in its favour familiar technology, adapted well to local facilities. It also consumed a wide variety of fuels; this led to its continued use in many countries to the end of the 20th century.

Steam engines have considerably less thermal efficiency than modern diesels, requiring constant maintenance and labour to keep them operational.[50] Water is required at many points throughout a rail network and becomes a major problem in desert areas, as are found in some regions within the United States, Australia and South Africa. In other localities the local water is unsuitable. The reciprocating mechanism on the driving wheels of a two-cylinder single expansion steam locomotive tended to pound the rails (see "hammer blow"), thus requiring more maintenance. Raising steam from coal took a matter of hours which brought serious pollution problems. Coal-burning locomotives required fire cleaning and ash removal between turns of duty. This was all done in the open air by hand in deplorable working conditions. Diesel or electric locomotives, by comparison, drew benefit from new custom built servicing facilities. Finally, the smoke from steam locomotives was deemed objectionable; in fact, the first electric and diesel locomotives were developed to meet smoke abatement requirements,[51] although this did not take into account the high level of invisible pollution in diesel exhaust smoke, especially when idling. It should also be remembered that the power for electric trains is, for the most part, derived from steam generated in a power station—often fueled with coal.

U.S. decline[edit]

Northwestern Steel and Wire locomotive number 80, July 1964

Diesel locomotives began to appear in mainline service in the United States in the mid-1930s.[52] The diesel reduced maintenance costs dramatically, while increasing locomotive availability. On the Chicago, Rock Island and Pacific Railroad the new units delivered over 350,000 miles (560,000 km) a year, compared with about 120,000–150,000 for a mainline steam locomotive.[21] World War II delayed dieselisation in the U.S. The Gulf, Mobile and Ohio Railroad was the first large mainline railroad to convert to all Diesel locomotives in 1949 and Life magazine ran an article Dec 5, 1949 subtitled The GM&O puts all its steam engines to torch, becomes first major U.S. railroad to dieselize 100%.[53] The pace picked up in the 1950s.[citation needed] 1960 is normally considered the last year for regular Class 1 main line standard gauge steam operations in the United States, with operations on the Grand Trunk Western, Illinois Central, Norfolk and Western, and Duluth Missabe and Iron Range Railroads,[54] as well as Canadian Pacific operations in the state of Maine.[55]

However, the Grand Trunk Western used some steam on regular passenger trains into 1961, the last occurring unannounced on trains 56 and 21 in the Detroit area on September 20, 1961 with 4-8-4 6323, one day before its flue time expired.[56] The last standard gauge regular freight service steam by a class 1 railroad was on the isolated Leadville branch of the Colorado and Southern (Burlington Lines) October 11, 1962 with 2-8-0 641.[57] Narrow gauge steam was used for freight service by the Denver and Rio Grande Western on the 250-mile (400 km) run from Alamosa, Colorado to Farmington, New Mexico via Durango until service ceased December 5, 1968.[57] The Union Pacific is the only Class I railroad in the U.S. to have never completely dieselized, at least nominally. It has always had at least one operational steam locomotive, Union Pacific 844, on its roster.[58] Some U.S. shortlines continued steam operations into the 1960s, and the Northwestern Steel and Wire mill in Sterling, Illinois, continued to operate steam locomotives until December 1980.[59] Two surviving sections of the Denver and Rio Grande Western's San Juan Extension, now operating separately as the Cumbres and Toltec Scenic Railroad and the Durango and Silverton Narrow Gauge Railroad, continue to use steam locomotives and operate as tourist railroads.

British decline[edit]

British industrial steam in the 1970s: a Robert Stephenson & Hawthorn 0-4-0ST shunting coal wagons at Agecroft Power Station, Pendlebury, north of Manchester, in 1976

Trials of diesel locomotives and railcars began in Britain in the 1930s but made only limited progress. One problem was that British diesel locomotives were often seriously under-powered, compared with the steam locomotives against which they were competing.

After 1945, problems associated with post-war reconstruction and the availability of cheap domestic-produced coal kept steam in widespread use throughout the two following decades. However the ready availability of cheap oil led to new dieselisation programmes from 1955 and these began to take full effect from around 1962. Towards the end of the steam era, steam motive power was allowed to fall into a dire state of repair. The last steam-hauled service trains on the British Railways network ran in 1968, but the use of steam locomotives in British industry continued into the 1980s.[60] In June 1975 there were still 41 locations where steam was in regular use, and many more where engines were held in reserve in case of diesel failures.[61] Gradually, the decline of the ironstone quarries, steel, coal mining and shipbuilding industries—and the plentiful supply of redundant British Rail diesel shunters as replacements—led to the disappearance of steam power for commercial uses.[60][61]

Several hundred rebuilt and preserved steam locomotives are still used on preserved volunteer-run 'heritage' railway lines in the UK. A proportion of the locomotives are regularly used on the national rail network by private operators where they run special excursions and touring trains. A new steam locomotive, the LNER Peppercorn Class A1 60163 Tornado has been built (began service in 2009), and more are in the planning stage.

Russia[edit]

P36-0031 — last steam passenger locomotive built in Russia. Heritage run during Expo 1520 exhibition in Scherbinka, Moscow Oblast.

In the USSR, although the first mainline diesel-electric locomotive was built in USSR in 1924, the last steam locomotive (model П36, serial number 251) was built in 1956; it is now in the Museum of Railway Machinery at former Warsaw Rail Terminal, Saint Petersburg. In the European part of the USSR, almost all steam locomotives were replaced by diesel and electric locomotives in the 1960s; in Siberia and Central Asia, state records verify that L-class 2-10-0s, and LV-class 2-10-2s were not retired until 1985. Until 1994, Russia had at least 1,000 steam locomotives stored in operable condition in case of "national emergencies".[62][63][64]

South Africa[edit]

In South Africa, the last new locomotives purchased were 2-6-2+2-6-2 Garratts from Hunslet Taylor for the 2-foot (610 mm) gauge lines in 1968.[65] Another class 25NC locomotive, No. 3454, nicknamed the "Blue Devil" because of its colour scheme, received modifications including a most obvious set of double side-by-side exhaust stacks. In southern Natal, two former South African Railway 2 ft (610 mm) gauge NGG16 Garratts operating on the privatised Port Shepstone and Alfred County Railway (ACR) received some L. D. Porta modifications in 1990 becoming a new NGG16A class.[66]

By 1994 almost all commercial steam locomotives were put out of service, although many of them are preserved in museums or at railway stations for public viewing. Today only a few privately owned steam locomotives are still operating in South Africa, namely the ones being used by the 5-star luxury train Rovos Rail, and the tourist trains Outeniqua Tjoe Choo, Apple Express and (until 2008) Banana Express.

For more details on this topic, see List of South African locomotive classes.

China[edit]

Qianjin(QJ)heavy freight steam locomotive, kept in China Industrial Museum

China continued to build mainline steam locomotives until late in the century, even building a few examples for American tourist operations. China was the last main-line user of steam locomotives, such use ending officially on the Ji-Tong line at the end of 2005. Some steam locomotives are still (2014) in use in industrial operations in China. Some coal and other mineral operations maintain an active roster of JS or SY steam locomotives bought secondhand from China Rail. The last steam locomotive built in China was 2-8-2 SY 1772, finished in 1999. As of 2011, at least six Chinese steam locomotives exist in the United States – 3 QJ's bought by RDC (Nos. 6988 and 7081 for IAIS and No. 7040 for R.J. Corman), a JS bought by the Boone and Scenic Valley Railroad, and two SYs. No. 142 (ex-#1647) is owned by the NYSW for tourist operations, re-painted and modified to represent a 1920s era U.S. locomotive; No. 58 is operated by the Valley Railroad and modified to represent New Haven Railroad number 3025.

Germany[edit]

After the Second World War, Germany was divided into the Federal Republic of Germany, with the Deutsche Bundesbahn (founded in 1949) as the new state-owned railway, and the German Democratic Republic, where railway service continued under the old pre-war name Deutsche Reichsbahn.

For a short period after the war, both Bundesbahn (DB) and Reichsbahn (DR) still placed orders for new steam locomotives. They needed to renew the rolling stock, mostly with steam locomotives designed for accelerated passenger trains. Many of the existing predecessors of those types of steam locomotives in Germany had been lost in the battles or simply reached the end of their lifetime, e.g. the famous Prussian P 8. There was no need for new freight train engines, however, because thousands of the Classes 50 and 52 had been built during the Second World War.

The VEB Lokomotivbau Karl Marx Babelsberg (LKM) built 1956 this Steam locomotive No. 991777-4. Today pulls the locomotive the Heritage railway by the Radebeul–Radeburg railway, also known as the Lößnitzgrundbahn (Lössnitzgrund Railway). The Radebeul-Radeburg railway runs between Radebeul East station and the small towns of Moritzburg and Radeburg north of Dresden.

Because the concept of the so-called "Einheitslokomotiven", the still widely used standard locomotives from the 1920s and 1930s, was already outdated in the pre-war era, a whole new design for the new steam locomotives was developed by DB and DR, called "Neubaudampflokomotiven" (new build steam locomotives). In particular the steam locomotives made by the DB in West Germany, under the guidance of Friedrich Witte, respresented the latest evolution in steam locomotive construction, including all-welded frames, high performance boilers and roller bearings on all moving parts. But although these new DB classes (10, 23, 65, 66, 82) were said to be among the finest and best performing German steam locomotives ever built, none of those machines exceeded 25 years in service. The last one, 23 105 (still preserved), went into service in 1959.

The DR in East Germany placed a similar procurement plan, but their engines were not as elaborate owing to a lack of money for new locomotives and political restrictions. The purchase of new-build steam locomotives by the DR ended in 1960. But later, during the early 1960s, the DR found a way to reconstruct older locomotives to conform with contemporary requirements. The high-speed locomotive 18 201 and the class 01.5 are some remarkable designs from that programme.

About 1960, the Bundesbahn in West Germany decided to phase out all steam-hauled trains in ten years, but still had about 5,000 of them in running condition. Even though DB were very assertive in continuing the electrification on the main lines (in 1963 they reached 5000 km of electrified routes) and dieselisation with new developed stock, they did not reach that goal. But the steam services declined more and more. In 1972, the Hamburg and Frankfurt departments of the DB rail networks became the first ones that no longer operated steam locomotives in their areas. The remaining steam locomotives began to gather in rail yards like Rheine, Tübingen, Hof, Saarbrücken, Gelsenkirchen-Bismarck and some others, which soon became well known to rail enthusiasts. In 1975, DB's last steam express train took its final run on the Emsland-Line from Rheine to Norddeich in the upper north of Germany. Two years later, on 26 October 1977, the heavy freight engine 44 903 (computer-based new number 043 903-4) made her final run at the same railway yard. After this date, no regular steam service took place on the network of the DB until their privatisation in 1994.

In East Germany, the Reichsbahn had to continue steam operation until 1988 on standard gauge because of many economic and political reasons, even though there had been strong efforts to phase out steam since the 1970s. The last locomotives in service where of the classes 50.35 and 52.80, which hauled goods trains on rural main and branch lines. Unlike with the DB, up to the very end there was never such a concentration of steam locomotives in just a few yards in the East, because throughout the DR network the infrastructure for steam locomotives remained intact until the end of the GDR in 1990. This was also the reason that there was never a real strict "final cut" at steam operations, so the DR used steam locomotives as well from time to time until they merged with the DB in 1994.

But on their narrow-gauge lines, steam locomotives continued to be used on a daily year-round basis, mainly for tourist reasons. The largest of these is the Harzer Schmalspurbahn (Harz Narrow Gauge Railways) network in the Harz Mountains, but the lines in Saxony and on the coast of the Baltic Sea are also notable. Even though every former DR narrow gauge railway has undergone privatisation, the daily steam operations are still commonplace there.

Japan[edit]

Owing to the destruction of most of the nation's infrastructure during the Second World War and the cost of electrification and dieselisation, new steam locomotives were built in Japan until 1960. The number of Japanese steam locomotives reached a peak of 5,958 in 1946.[67]

With the booming post-war Japanese economy, steam locomotives were gradually withdrawn from main line service beginning in the early 1960s, and were replaced with diesel and electric locomotives. They were relegated to branch line and sub-main line services for several more years until the late 1960s, when electrification/dieselisation began in earnest. From 1970 onwards, steam locomotion was abolished on the JNR:

  • Shikoku (April 1970)
  • Kanto area (Tokyo) (October 1970),
  • Kinki (Osaka, Kyoto area) (September 1973)
  • Chubu (Nagoya, Nagano area) (April 1974),
  • Tohoku (November 1974),
  • Chugoku (Yamaguchi area) (December 1974)
  • Kyushu (January 1975)
  • Hokkaido (March 1976)

The last steam passenger train, pulled by a C57-class locomotive built in 1940, departed from Muroran railway station to Iwamizawa on 14 December 1975. It was then officially retired from service, dismantled and sent to the Tokyo Transportation Museum, where it was officially inaugurated as an exhibit on 14 May 1976. It was moved to the Saitama Railway Museum in early 2007. The last Japanese main line steam train, D51-241, a D51-class locomotive built in 1939, left Yubari railway station on 24 December 1975. That same day, all steam main line service ended. D51-241 was retired on 10 March 1976, and destroyed in a depot fire a month later, though a few parts were preserved.

On 2 March 1976, the final steam locomotive still operating on the JNR, 9600-39679, a 9600-class locomotive built in 1920, made its final journey from Oiwake railway station, ending 104 years of steam locomotion in Japan.[68]

South Korea[edit]

The first steam locomotive in South Korea (Korea at the time) was the Moga (Mogul), which first ran on 9 September 1899 (Gyeong-In Line) 2-6-0, followed by Sata, Pureo, Ame, Sig, Mika (USRA Heavy Mikado), Pasi (USRA Light Pacific), Hyeogi (Narrow gauge), Class 901, Mateo, Sori and Tou. Used until 1967, the Moga is now in the Railroad Museum.[citation needed]

Other countries[edit]

Reading and Northern Railroad number 425 being readied in Pennsylvania, U.S.A., for the daily tourist train in 1993.

In other countries, the dates for conversion from steam varied.

On the contiguous North American standard gauge network including Canada, Mexico and the United States, standard gauge main line steam with 1946-built 4-8-4's handling freight between Mexico City and Irapuato lasted until 1968 (Eagleson, Ziel, 1973 The Twilight of World Steam). The Mexican Pacific, a standard gauge short line in the state of Sinaloa, was reported in August 1987 (World Steam Magazine #101) to still be using steam, with a roster of one 4-6-0, two 2-6-2's and one 2-8-2.

By March 1973 in Australia, steam had vanished in all states. Diesel locomotives were more efficient and the demand for manual labour for service and repairs was less than steam. Cheap oil had cost advantages over coal.

Steam traction in New Zealand ended in 1968 in the North Island when AB 832 (now stored at the Glenbrook Vintage Railway, Auckland, but owned by MOTAT) hauled a Farmer's 'Santa Special' from Frankton Junction to Claudelands. Due to the inability of the new DJ class diesel locomotives to provide in-train steam heating, steam operations continued using the J and JA class 4-8-2 tender locomotives on the overnight Christchurch-Invercargill expresses, Trains 189/190, until 1971. By this time sufficient FS steam-heating vans were available, thus allowing the last steam locomotives to be withdrawn. Two AB class 4-6-2 tender locomotives, AB 778 and AB 795, were retained at Lyttelton to steam-heat the coaches for the Boat Trains between Christchurch and Lyttelton until they were restored for the Kingston Flyer tourist train in 1972.

In Finland, the first diesels were introduced in the mid-1950s and they superseded the steam locomotives during the early 1960s. The State Railways (VR) operated steam locomotives until 1975.

In the Netherlands, the first electric trains made there appearance in 1908 from Rotterdam to The Hague. The first diesels were introduced in 1934. As electric and dieseltrains performed so well, the decline of steam started just after WW II and in 1958 steamtraction ended.

In Poland, on non-electrified tracks steam locomotives were superseded almost entirely by diesels by the 1990s. A few steam locomotives, however, operate still from Wolsztyn. Although they are maintained operational rather as a means of preserving railway heritage and as a tourist attraction, they do haul regular scheduled trains (mostly to Poznań). Apart from that, numerous railway museums and heritage railways (mostly narrow gauge) own steam locomotives in working condition.

In France, steam locomotives have not been used for commercial services since 24 September 1975.[69]

In Bosnia and Herzegovina, some steam locomotives are still used for industrial purposes, for example at coal mineyard in Banovići[70] and ArcelorMittal factory in Zenica.[71]

In India, steam locomotives were built as late as 1972 and in use until 2000; they were replaced by a combination of diesel and electric locomotives. A steam locomotive celebration run was organised between Thane and Mumbai to commemorate the 150th year of railways in India.

In Sri Lanka, one steam locomotive is maintained for private service to power the Viceroy Special.

B 5112 before being reactivated in Ambarawa Railway Museum, Indonesia

Indonesia also has experience with steam locomotives since 1876. The last batch of E10 0-10-0 rack tank locomotives were purchased as late as 1967 (Kautzor, 2010) from Nippon Sharyo. The last locomotives – manufactured by Krupp, Germany, D 52 class, in 1954 – operated until 1994. In 1994 they were replaced by diesel locomotives. Indonesia also purchased the last batch of mallet locomotives from Nippon Sharyo, to be used in the Aceh Railway. In Sumatra Barat (West Sumatra) and Ambarawa we can find the rack railway track train (with maximum elevated 6% in mountainous area), now operated for tourism only. There are two museums, Taman Mini and Ambarawa (Ambarawa Railway Museum).[72]

Pakistan still has a regular steam locomotive service; a line operates in the North-West Frontier Province and Sindh; It has been preserved as a "nostalgia" service for tourism in exotic locales,[73] indeed it is specifically advertised as being for "steam buffs".[73]

In Thailand all steam locomotives were withdrawn from service during the late 1960s to early 1970s. Most were scrapped in 1980. However there are about 20 to 30 locomotives preserved for exhibit in important or end-of-the-line stations throughout the country. During the late 1980s, six locomotives were restore to running condition. Most are JNR built 4-6-2 steam locomotives with the exception of a single 2-8-2.

Revival[edit]

Er 774 38 0-10-0 on Steam Special Train in Moscow 11 July 2010
60163 Tornado, a new express locomotive built for the British main line, completed in 2008

Dramatic increases in the cost of diesel fuel prompted several initiatives to revive steam power.[74][75] However none of these has progressed to the point of production and, in the early 21st century, steam locomotives operate only in a few isolated regions of the world and in tourist operations. In Germany, a small number of fireless steam locomotives are still working in industrial service, e.g., at power stations, where an on-site supply of steam is readily available.

The Swiss company Dampflokomotiv- und Maschinenfabrik DLM AG delivered eight steam locomotives to rack railways in Switzerland and Austria between 1992 and 1996. Four of them are now the main means of traction on the Brienz Rothorn Bahn; the four others were for the Schafbergbahn in Austria, where they run 90% of the trains.

The same company rebuilt a German 2-10-0 locomotive to new standards with modifications such as roller bearings, light oil firing and boiler insulation.[76]

2-6-0 type "N3" steam locomotive built by Beyer Peacock in 1910 for the Central Uruguay Railway. Numbered 120, this locomotive was restored between 2005 and 2007 by the Uruguayan Railfan Association (AUAR is their Spanish acronym). The photo shows the locomotive with a passenger tourist train in March 2013 at the station of Peñarol neighbourhood in Montevideo where a museum was set up to show the railway heritage of that area.

Several heritage railways in the UK have built new steam locomotives in the 1990s and early 21st century. These include the narrow gauge Ffestiniog and Corris railways in Wales. The Hunslet Engine Company was revived in 2005 and is now building steam locomotives on a commercial basis.[77] A standard gauge LNER Peppercorn Pacific "Tornado" was completed at Hopetown Works, Darlington, England and made its first run on 1 August 2008.[78][79] It entered main line service later in 2008, to great public acclaim. Demonstration trips in France and Germany have been planned.[80] As of 2009 over half-a-dozen projects to build working replicas of extinct steam engines are going ahead, in many cases using existing parts from other types to build them. Examples include BR Class 6MT Hengist ,[81] BR Class 3MT no. 82045, BR Class 2MT no. 84030,[82] Brighton Atlantic Beachy Head ,[83] the LMS "Patriot 45551 The Unknown Warrior" project, GWR "47xx 4709, BR "Class 6 72010 Hengist, GWR "Saint" 2999 Lady of Legend, 1014 "County" of Glamorgan and 6880 Betton "Grange" projects.

South African Class 26, the Red Devil

In 1980 American financier Ross Rowland established American Coal Enterprises to develop a modernised coal-fired steam locomotive. His ACE 3000 concept attracted considerable attention, but never materialised.[84][85]

In 1998, in his book The Red Devil and Other Tales from the Age of Steam,[86] David Wardale put forward the concept of a high speed, high efficiency "Super Class 5 4-6-0" locomotive for future steam haulage of tour trains on British main lines. The idea was formalised in 2001 by the formation of 5AT Project dedicated to developing and building the 5AT Advanced Technology Steam Locomotive, but it never received any major railway backing.

Locations where new builds are taking place include:[citation needed]

In 2012, the Coalition for Sustainable Rail[87] project was started in the USA with the goal of creating a higher speed, modern steam locomotive incorporating all the improvements proposed for steam locomotion by Livio Dante Porta and others, but using torrefied biomass as solid fuel. The fuel has been recently developed by the University of Minnesota and the project is a collaboration between the university's Institute on the Environment (IonE) and Sustainable Rail International (SRI), an organisation set up to explore the use of steam traction in a modern railway setup. The group have received the last surviving (but non-running) ATSF 3460 class steam locomotive (#3463) via donation from its owner in Kansas, the Great Overland Station Museum, and intend to use it as a platform for developing "the world’s cleanest, most powerful passenger locomotive" (sic) capable of speeds up to 130 mph. Named Project 130, it aims to break the world steam train speed record set by LNER Class A4 4468 Mallard in the UK at 126 mph. However, any demonstration of the project's claims is yet to be seen.

Steam locomotives in popular culture[edit]

Steam locomotives have captured people's imaginations since they first chugged into history. Folk songs about steam engines including "John Henry" and "I've Been Working on the Railroad" are a mainstay of American music and culture. Over the years, steam locomotives have become a very popular image in representations of trains. Many toy trains based on steam locomotives are made, thereby making the image iconic with trains to children. Their popularity has led to steam locomotives being portrayed in fictional works about trains, most notably The Railway Series by the Rev W. V. Awdry and The Little Engine That Could by Watty Piper. Steam locomotives have also been "stars" in many television shows about trains, such as Thomas the Tank Engine and Friends, based on characters from the books by Awdry.

There is also the Hogwarts Express from J.K. Rowling's Harry Potter series, which in the films is portrayed by the GWR 4900 Class 5972 Olton Hall steam engine in special Hogwarts livery. The Hogwarts Express is so popular in its own right that it is an attraction at The Wizarding World of Harry Potter section of the Universal Studios Islands of Adventure amusement park in Florida.

The animated movie, The Polar Express, and the book, by Chris VanAllsburg have inspired numerous Christmas themed trips, including the North Pole Express pulled by former Pere Marquette Railway #1225 out of Owosso, Michigan, which according to VanAllsburg, inspired the story and which was used in the production of the movie. Models of that engine are available from Lionel.

Coins[edit]

The Biedermeier Period coin featuring a steam locomotive
The state quarter representing Utah, depicting the golden spike ceremony

Steam locomotives are a main topic for numerous collectors and bullion coins.

The 1950 Silver 5 Peso coin of Mexico has a steam locomotive on its reverse as the prominent feature.

The recent 20 euro Biedermeier Period coin, minted 11 June 2003, shows on the obverse an early model steam locomotive (the AJAX) on Austria's first railway line, the Kaiser Ferdinand's Nordbahn. The AJAX can still be seen today in the Austrian Railway Museum.

As part of the 50 State Quarters program, the quarter representing the U.S. state of Utah depicts the ceremony where the two halves of the First Transcontinental Railroad met at Promontory Summit in 1869. The coin recreates a popular image from the ceremony with steam locomotives from each company facing each other while the golden spike is being driven.

See also[edit]

General[edit]

Types of steam locomotives[edit]

Historic locomotives[edit]

References[edit]

  1. ^ V.A. Rakov, Locomotives Series B, Locomotives on domestic railways 1845-1955, 2nd ed., revised and enlarged, Moscow: "Transport", 1995, pp. 233-234, ISBN 5-277-00821-7
  2. ^ Payton, Philip (2004). Oxford Dictionary of National Biography. Oxford University Press. 
  3. ^ Gordon, W.J. (1910). Our Home Railways, volume one. London: Frederick Warne and Co. pp. 7–9. 
  4. ^ http://books.google.co.uk/books?id=nVtEAAAAQBAJ&pg=PA13&lpg=PA13&dq=John+Fitch+Locomotive&source=bl&ots=mQHn_m0mO3&sig=nr3U2bf7Nd3lPSPPisMtzVGSTuI&hl=en&sa=X&ei=xxhiVLqcCITlapX5gOgN&ved=0CC8Q6AEwCDgK
  5. ^ Ohio Historical Society – catalogue search (model of steam locomotive)[dead link]
  6. ^ "Richard Trevithick's steam locomotive | Rhagor". Museumwales.ac.uk. Retrieved 2009-11-03. 
  7. ^ "Steam train anniversary begins". BBC. 2004-02-21. Retrieved 2009-06-13. A south Wales town has begun months of celebrations to mark the 200th anniversary of the invention of the steam locomotive. Merthyr Tydfil was the location where, on 21 February 1804, Richard Trevithick took the world into the railway age when he set one of his high-pressure steam engines on a local iron master's tram rails 
  8. ^ Payton, Philip (2004). Oxford Dictionary of National Biography. Oxford University Press. 
  9. ^ Garnett, A.F. (2005). Steel Wheels. Cannwood Press. pp. 18–19. 
  10. ^ Young, Robert (2000). Timothy Hackworth and the Locomotive ((=reprint of 1923 ed.) ed.). Lewes, UK: the Book Guild Ltd. 
  11. ^ a b Hamilton Ellis (1968). The Pictorial Encyclopedia of Railways. The Hamlyn Publishing Group. pp. 24–30. 
  12. ^ Ahrons. The British Steam Railway Locomotive from 1825 to 1925. vol. 1. 
  13. ^ See section of the LNER Class A1/A3 article on the sharp increase in availability brought about in this respect by the application of the Kylchap exhaust to Gresley Pacifics in the early 1960s
  14. ^ J.J.G. Koopmans: The fire burns much better ... NL-Venray 2006, ISBN 90-6464-013-0
  15. ^ White, John H., Jr. (1997). American Locomotives, an Engineering History 1830–1880, Revised and Expanded Edition. Baltimore, USA: Johns Hopkins Press. p. 85. ISBN 0-8018-5714-7. 
  16. ^ "West Coast and R711". Newsgroupaus.rail. 
  17. ^ a b c d Swengel p. 146
  18. ^ Porta Treatment Advanced Internal Boiler Water Treatment
  19. ^ Coalition for Sustainable Rail
  20. ^ Scott, Ron; GN Large Atlantics (Profile Publications Berks UK – no date), p. 129
  21. ^ a b c d e f g Bell, A Morton (1950). Locomotives (seventh ed.). London: Virtue & Co Ltd,. 
  22. ^ White, John H. Jr. (1968). A history of the American locomotive, its development: 1830–1880 ((Reprint: Dover Publications, New York 1979) ed.). Baltimore, USA: Johns Hopkins Press. pp. 146–149. 
  23. ^ a b c Snell, John B (1971). Mechanical Engineering: Railways. London: Longman. 
  24. ^ White 1968, pp. 114–124
  25. ^ BTC Handbook 1957, p. 40
  26. ^ Hollingsworth, Brian; Cook, Arthur (1987). The Great Book of Trains. London: Salamander Books. p. 192. 
  27. ^ "Cass City Chronicle" (PDF). Cass City Chronicle: 3. July 29, 1938. Retrieved 2007-09-26. 
  28. ^ "Pennsylvania Railroad chemical laboratory". U.S. National Park Service online history resource. Retrieved 2006-11-09. 
  29. ^ Handbook for Railway Steam Locomotive Enginemen. London: British Transport Commission. 1957. pp. 126–127. OCLC 4431123. 
  30. ^ Railway Magazine (London: International Printing Company) 99: 287. 1953. 
  31. ^ BTC Handbook 1957, p. 53
  32. ^ Oxford English Dictionary: Buff 1
  33. ^ "Glossary of Terms and Definitions," accessed 21 Feb. 2012
  34. ^ "Railway Regulation Act 1842". UK Statute Law Database. 30 July 1842. Retrieved 5 March 2012. 
  35. ^ White, John H., Jr. (1997). American Locomotives, an Engineering History 1830–1880, Revised and Expanded Edition. Baltimore, USA: Johns Hopkins Press. pp. 213–214. ISBN 0-8018-5714-7. 
  36. ^ "Steam Still Rules the Rails" Popular Science, December 1937, drawing pp. 32–33 on multi-cylinders arrangement
  37. ^ Van Riemsdijk, John T. (1994). Compound locomotives, an international survey. Penryn, England: Atlantic Transport Publishers. ISBN 0-906899-61-3. 
  38. ^ David Ross, The Steam Locomotive: a History, Tempus Publishing, Gloucestershire, 2006, ISBN 0-7524-3916-2
  39. ^ Electric-steam locomotives of Switzerland
  40. ^ Ahrons, E.L. (1987) [1927]. The British Steam Railway Locomotive 1825–1925. London: Bracken Books. p. 123. ISBN 1-85170-103-6. 
  41. ^ Oberg, Leon (1975), Locomotives of Australia, A.H. and A.W. Reed, ISBN 978-0-589-07173-8 
  42. ^ a b Gunzburg, Adrian (1984), A History of W.A.G.R. Steam Locomotives, Australian Railway Historical Society (Western Australian Division), Perth, Western Australia, ISBN 978-0-589-07173-8 
  43. ^ "Pennsylvania Railroad locomotive classification @ Everything2.com". Everything2.com. 2003-02-02. Retrieved 2009-11-03. 
  44. ^ LNWR Society. "LNWR Locomotive classes". Lnwrs.org.uk. Retrieved 2009-11-03. 
  45. ^ "Scots Dictionary". Dsl.ac.uk. Retrieved 2009-11-03. 
  46. ^ Adams, Henry (1908). Cassell's Engineer's Handbook. London: Cassell and Company. p. 389. 
  47. ^ Allen, Cecil J (1949). Locomotive Practice and Performance in the Twentieth Century. Cambridge, England: W Heffer and Sons Ltd. 
  48. ^ * Meiklejohn, Bernard (January 1906). "New Motors on Railroads: Electric and Gasoline Cars Replacing the Steam Locomotive". The World's Work: A History of Our Time XIII: 8437–8446–8454. Retrieved 2009-07-10. 
  49. ^ "The Construction of and Performance Obtained from the Oil Engine". 
  50. ^ http://www.sdrm.org/faqs/hostling.html, Phil Jern "How to Boot a Steam Locomotive" (1990) San Diego Railroad Museum.
  51. ^ Diesel Traction Manual for Enginemen. British Transport Commission. 1962. pp. 15–16. 
  52. ^ The Pioneer Zephyr first ran in 1934.
  53. ^ "Locomotive Graveyard". Life magazine. December 5, 1949. p. 155. Retrieved November 24, 2014. 
  54. ^ Stagner,1991 National Ry. Bul. Vol.56 #4.
  55. ^ Holland, 2006 Canadian Pacific Steam, Vol. 1.
  56. ^ Stagner, 1991; Pinkepank, 2003 Grand Trunk Western Vol. 1.
  57. ^ a b Stagner, 1991.
  58. ^ "UP: Steam Locomotive No. 844". Uprr.com. Retrieved 2009-11-03. 
  59. ^ "Last locomotive to operate in the United States". Library Service of Northern Illinois University. Retrieved 2007-11-05. 
  60. ^ a b Industrial Steam. Ian Allan. 1994. p. 3. ISBN 0-7110-2230-5. 
  61. ^ a b Booth, Adrian J (1976). Industrial Steam. Bradford Barton. p. (Introduction). ISBN 0-85153-236-5. 
  62. ^ "Varshavsky Vokzal Museum of Railway Machinery". Nevsky-prospekt.com. Retrieved 2009-11-03. 
  63. ^ "(in Russian)". Semafor.narod.ru. Retrieved 2009-11-03. 
  64. ^ "(in Russian)". Dvgups.ru. Retrieved 2009-11-03. 
  65. ^ Durrant, A. E.; Jorgensen, A. A.; Lewis, C. P. (1972). Steam on the veld: steam in South Africa during the 60's. London: Allan. p. 61. ISBN 0-7110-0240-1. 
  66. ^ VidRail Productions, South African end of Steam: Orange Free State, Part 4, Vols. 3, 4 and 5 and Natal, Part 3, Vol. 1, in The Best of Southern African Steam, 1983–1990
  67. ^ The Last days of Japanese Steam Engines
  68. ^ The Last days of Japanese Steam Engine
  69. ^ "ressource pédagogique – La locomotive ŕ vapeur : son évolution technique – texte d'approfondissement". Mulhouseum.uha.fr. Retrieved 2009-11-03. 
  70. ^ "Forum discussion". 
  71. ^ "Forum discussion". 
  72. ^ "The Ambarawa Railway Museum". Internationalsteam.co.uk. 2008-11-30. Retrieved 2009-11-03. 
  73. ^ a b "Pakistan Railway". Pakrail.com. Retrieved 2009-11-03. [dead link]
  74. ^ "The 5AT project to develop a modern steam locomotive for British railways". 
  75. ^ "Railway Extension Across the Andes: reactivation and modernisation of existing fleet of 75 cm gauge 2-10-2 steam locomotives". 
  76. ^ "Reference work of DLM AG 2-10-0 locomotive 52 8055". 
  77. ^ Staff. "About Hunslet Steam Co". Hunslet Hunslet Engine Company. Retrieved 2008-08-04. 
  78. ^ Roberts, David (2008-08-03). "Newly-built steam loco takes to the tracks". Darlington and Stockton Times. Retrieved 2008-08-04. 
  79. ^ Staff (2008-09-22). "60163 Tornado is on the go". BBC Tees. Retrieved 2008-10-01. 
  80. ^ Glancy, Jonathan (2008-08-02). "New steam locomotive unveiled". The Guardian (London). Retrieved 2008-08-04. 
  81. ^ "Hengist official website". 72010-hengist.org. Retrieved 2009-11-03. 
  82. ^ "84030 page on the Bluebell Railway website". Bluebell-railway.co.uk. 2008-04-14. Retrieved 2009-11-03. 
  83. ^ "Beachy Head section on the Bluebell Railway website". Bluebell-railway.co.uk. Retrieved 2009-11-03. 
  84. ^ "The Ultimate Steam Page". Trainweb.org. Retrieved 2009-11-03. 
  85. ^ "American Coal Enterprises – ACE3000 et al". Martynbane.co.uk. Retrieved 2009-11-03. 
  86. ^ Wardale, David (1998). The Red Devil and Other Tales from the Age of Steam. Published by the author. ISBN 0-9529998-0-3. 
  87. ^ http://www.csrail.org

Further reading[edit]

  • C. E. Wolff, Modern Locomotive Practice: A Treatise on the Design, Construction, and Working of Steam Locomotives (Manchester, England, 1903)
  • Henry Greenly, Model Locomotive (New York, 1905)
  • G. R. Henderson, Cost of Locomotive Operation (New York, 1906)
  • W. E. Dalby, Economical Working of Locomotives (London, 1906)
  • A. I. Taylor, Modern British Locomotives (New York, 1907)
  • E. L. Ahrons, The Development of British Locomotive Design (London, 1914)
  • E. L. Ahrons, Steam Engine Construction and Maintenance (London, 1921)
  • J. F. Gairns, Locomotive Compounding and Superheating (Philadelphia, 1907)
  • Angus Sinclair, Development of the Locomotive Engine (New York, 1907)
  • Vaughn Pendred, The Railway Locomotive, What it is and Why it is What it is (London, 1908)
  • Brosius and Koch, Die Schule des Lokomotivführers (thirteenth edition, three volumes, Wiesbaden, 1909–1914)
  • G. L. Fowler, Locomotive Breakdowns, Emergencies, and their Remedies (seventh edition, New York, 1911)
  • Fisher and Williams, Pocket Edition of Locomotive Engineering (Chicago, 1911)
  • T. A. Annis, Modern Locomotives (Adrian Michigan, 1912)
  • C. E. Allen, Modern Locomotive (Cambridge, England, 1912)
  • W. G. Knight, Practical Questions on Locomotive Operating (Boston, 1913)
  • G. R. Henderson, Recent Development of the Locomotive (Philadelphia, 1913)
  • Wright and Swift (editors) Locomotive Dictionary (third edition, Philadelphia, 1913)
  • Roberts and Smith, Practical Locomotive Operating (Philadelphia, 1913)
  • E. Prothero, Railways of the World (New York, 1914)
  • M. M. Kirkman, The Locomotive (Chicago, 1914)
  • C. L. Dickerson, The Locomotive and Things You Should Know About it (Clinton, Illinois, 1914)
  • P. W. B. Semmens, A. J. Goldfinch, How Steam Locomotives Really Work (Oxford University Press, USA, 2004) ISBN 0-19-860782-2
  • Gerald A Dee, A Lifetime of Railway Photography in Photographer Profile, Train Hobby Publications, Studfield, 1998. (Australian steam)
  • Swengel, F. M. The American Steam Locomotive; Vol. 1. The Evolution of the American Steam Locomotive, Midwest Rail Publication, Iowa, 1967.
  • Раков В.А. Локомотивы отечественных железных дорог 1845–1955 Транспорт, Москва, 1995
    (Rakov V.A. Locomotives of fatherland's railways 1845–1955 Transport, Moscow, 1995 (in Russian))
  • J.J.G. Koopmans: The fire burns much better ... NL-Venray 2006, ISBN 90-6464-013-0

External links[edit]