Bren light machine gun: Difference between revisions

Bren Gun
Bren Gun
	Early Mark Bren LMG, photo from a Canadian factory
Type	Light machine gun
Service history
Wars	World War II, Korean War
Specifications
Mass	22.82 lb (10.35 kg)
Length	42.9 in (1,156 mm), Mk IV

Browse history interactively

← Previous edit Next edit →

Content deleted Content added

VisualWikitext

Inline

Revision as of 06:43, 6 May 2006

The Bren, usually called the Bren Gun was a series of machine guns adopted by Britain in the 1930s and used in various roles into the 1980s. Whilst it is best known for its role as the British and Commonwealth forces primary infantry light machine gun (LMG) in World War II, it was also used in Korea and saw service throughout the later half of the 20th century including the Falklands campaign and the 1991 Gulf War.

It was a version of a Czechoslovakian design developed to British requirements for a competition in the 1930s, and originally featured a distinctive curved box magazine, conical flash hider, and quick change barrel. In the 1950s it was rebarrelled to accept the 7.62 x 51 mm NATO cartridge, which also meant that the straight magazines for the 7.62 rimless ammunition needed to be used. Although fitted with a bipod, it could also be mounted on a tripod and on many vehicles.

The Bren was replaced as the section LMG by the L7 GPMG, a heavier belt-fed weapon. This was in turn replaced in the 1980s by the much maligned Light Support Weapon (LSW) firing the 5.56 x 45 mm NATO round, leaving the L4 only in use on some vehicles.

Development

The British Army adopted it in 1935 following extensive trials of the Czech ZB vz.27 light machine gun which was manufactured in Brno. A licence to manufacture was sought and the Czech design modified to British requirements. The major changes were in the magazine and barrel to take the .303 British round which was rimmed rather than the rimless 7.92 mm Mauser round. The name was formed as a contraction from "Brno" and "Enfield" (the Royal Small Arms Factory, or RSAF, in Enfield, where it would be manufactured).

A gas operated weapon, it used the same ammunition as the standard British rifle, the Lee Enfield No 4, firing at a rate of between 480 and 540 rounds per minute (rpm), depending on the model. Each gun came with a spare barrel that could be quickly changed when the barrel became hot during sustained firing, although later guns featured a chrome-lined barrel which reduced need for the spare. Also, it only accepted magazines, and so usually demanded more frequent reloading than belt-fed machine guns. It was however several pounds lighter than belt-fed models, and could be used more easily on the move and from standing positions. The magazines also prevented the rounds from getting dirty, something that was hard to do when using 50-round belts.

Service

The Bren was fitted with a 30-round magazine that in practice was usually filled with only 28 or 29 rounds to prevent jamming and avoid wearing out the magazine spring, something that was common to other firearms as well. Care needed to be taken with magazine loading to ensure that the cartridge rims did not overlap, causing a jam. There was also a 100-round drum magazine available for the Bren used in the anti-aircraft role.

Some considered the Bren too accurate because its cone of fire was extremely concentrated. When used for suppressive fire this was not as useful, however for accurate shooting it was much better; rather than spraying as many bullets as possible for a hit, it relied on the accuracy of the gun and an experienced gunner.

For a light machine gun of the period it was about average weight. On long marches in non-operational areas it was often partially disassembled and its parts carried by two soldiers. Writing about his experiences in the infantry during the Burma campaign, the author George MacDonald Fraser stated that one Bren gun was issued to each eight man section. One soldier would be the gunner and another would be his 'number two', who would carry extra ammunition and the spare barrel and change magazines in combat. On occasion, one soldier would use the gun on the move like an automatic rifle. Generally, each soldier's equipment included two magazines for the section's Bren gun.

The Bren was also used on many vehicles as well, including Universal Carriers, on tanks, and armoured cars. However, on tanks it was not used in the co-axial role but on a pintle mount. The co-axial requirement was filled by the faster firing Besa, another Czechoslovakian machine gun design adopted by the British.

It was popular with British troops who respected the Bren for its high reliability and combat effectiveness and few would have swapped it for anything else. Many considered it the best light machine gun ever made. Re-worked to take the NATO standard 7.62 mm round, it was redesignated as the L4 series of light machine guns and continued in British Army service into the 1990s. The change from rimmed to rimless cartridge meant the distinctive curved magazine could be replaced by an easy-to-use almost straight magazine as on the original Czech design. 20-round magazines from the 7.62 mm L1A1 rifle could also be used. The conical flash hider was also lost in the transition, being replaced by the slotted type similar to that of the contemporary L1 rifle and L7 general purpose machine gun.

The completion of the move to a 5.56 mm cartridge for all infantry firearms has seen the end of the Bren/L4 in infantry service. The Bren had an effective range of 600 yd.

Variants

Mark 1

From September 1937. The original Bren based on the Czech gun.

Mark 2

Introduced 1941. A simpler version of the Mk 1. Produced by the Monotype Group through a number of component manufacturing factories.

Mark 3

A shorter and lighter Bren made by Enfield for the war in the East from 1944.

Mark 4

From 1944.

L4

From 1958. L4 Brens can easily be identified by their straighter magazine. All L4s are chambered for 7.62 x 51 mm NATO rimless ammunition.

Designation	Description
L4A1	Bren Mk III conversion, with Mk I bipod and steel barrel
L4A2	Bren Mk III conversion, lightened bipod and steel barrel
L4A3	Bren Mk II conversion
L4A4	L4A2 variant with chrome barrel
L4A5	L4A3 with chrome barrel for Royal Navy
L4A6	L4A1 variant with chrome barrel
L4A9	Bren conversion with L7 dovetail

World War II Production

RSAF Enfield, UK: 400 per month.

John Inglis and Company, Canada: A Contract was signed with the British and Canadian governments in March 1938 to supply 5,000 Bren machine guns to Great Britain and 7,000 Bren machine guns to Canada. Both countries shared the capital costs of bringing in this new production facility. Production started in 1940; and by 1943 John Inglis and Company was producing 60% of the world output of Bren machine guns.

Lithgow, Australia.

Use

British and Commonwealth forces (Some still in use with Reserve Forces in New Zealand.)
Irish Defence Forces (Some still in use with Reserve Defence Forces (RDF) in the Republic of Ireland) These have been replaced by FN MAG in 2006.
Chinese Army of Chiang Kai-shek
The Bren gun can be seen in action in the British gangster movie Lock, Stock and Two Smoking Barrels.

@@ Line 44: / Line 44: @@
 Some considered the Bren too accurate because its cone of fire was extremely concentrated. When used for [[suppressive fire]] this was not as useful, however for accurate shooting it was much better; rather than spraying as many bullets as possible for a hit, it relied on the accuracy of the gun and an experienced gunner.
-For a light machine gun of the period it was about average weight. On long marches it was often partially disassembled and its parts carried by two soldiers. Writing about his experiences in the infantry during the [[Burma Campaign|Burma campaign]], the author [[George MacDonald Fraser]] stated that one Bren gun was issued to each eight man [[Section (military unit)|section]]. One soldier would be the gunner and another would be his 'number two', who would carry extra ammunition and the spare barrel and change magazines in combat. On occasion, one soldier would use the gun on the move like an automatic rifle. Generally, each soldier's equipment included two magazines for the section's Bren gun.
+For a light machine gun of the period it was about average weight. On long marches in non-operational areas it was often partially disassembled and its parts carried by two soldiers. Writing about his experiences in the infantry during the [[Burma Campaign|Burma campaign]], the author [[George MacDonald Fraser]] stated that one Bren gun was issued to each eight man [[Section (military unit)|section]]. One soldier would be the gunner and another would be his 'number two', who would carry extra ammunition and the spare barrel and change magazines in combat. On occasion, one soldier would use the gun on the move like an automatic rifle. Generally, each soldier's equipment included two magazines for the section's Bren gun.
 The Bren was also used on many vehicles as well, including [[Universal Carriers]], on tanks, and armoured cars. However, on tanks it was not used in the co-axial role but on a pintle mount. The co-axial requirement was filled by the faster firing [[Besa]], another Czechoslovakian machine gun design adopted by the British.