Jump to content

Polydimethylsiloxane

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Glaurung (talk | contribs) at 07:26, 7 October 2009 (→Applications: removed PDMS used in Dry cleaning. D5 is a silicone, but not PDMS. (you don't want PDMS on your clothes, that's for sure!)). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Polydimethylsiloxane
PDMS
PDMS
Names
IUPAC name
poly(dimethylsiloxane)
Other names
PDMS
dimethicone
E900
Identifiers
ECHA InfoCard 100.126.442 Edit this at Wikidata
E number E900 (glazing agents, ...)
Properties
(C2H6OSi)n
Density 965 kg m−3
Melting point N/A (vitrifies)
Boiling point N/A (vitrifies)
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
checkY verify (what is checkY☒N ?)

Polydimethylsiloxane (PDMS) belongs to a group of polymeric organosilicon compounds which are commonly referred to as silicones[1]. PDMS is the most widely used silicon-based organic polymer, and is particularly known for its unusual rheological (or flow) properties. Its applications range from contact lenses and medical devices to elastomers, in shampoos (as dimethicone makes hair shiny and slippery), caulking, lubricating oils and heat resistant tiles.

PDMS is optically clear, and is generally considered to be inert, non-toxic and non-flammable. It is occasionally called dimethicone and is one of several types of silicone oil (polymerized siloxane).

Chemistry

The chemical formula for PDMS is (H3C)3SiO[Si(CH3)2O]nSi(CH3)3, where n is the number of repeating monomer [SiO(CH3)2] units. Industrial synthesis can begin from dimethylchlorosilane and water by the following net reaction:

n Si(CH3)2Cl2 + n H2O → [Si(CH3)2O]n + 2n HCl

During polymerization, this reaction evolves potentially hazardous hydrogen chloride gas. For medical uses, a process was developed where the chlorine atoms in the silane precursor were replaced with acetate groups, so that the reaction product of the final curing process is nontoxic acetic acid (vinegar). As a side effect, the curing process is also much slower in this case. This is the chemistry used in consumer applications, such as silicone caulk and adhesives.

Silane precursors with more acid-forming groups and fewer methyl groups, such as methyltrichlorosilane, can be used to introduce branches or cross-links in the polymer chain. Ideally, each molecule of such a compound becomes a branch point. This can be used to produce hard silicone resins. Similarly, precursors with three methyl groups can be used to limit molecular weight, since each such molecule has only one reactive site and so forms the end of a siloxane chain.

The polymer is manufactured in multiple viscosities, ranging from a thin pourable liquid (when n is very low), to a thick rubbery semi-solid (when n is very high). PDMS molecules have quite flexible polymer backbones (or chains) due to their siloxane linkages, which are analogous to the ether linkages used to impart rubberiness to polyurethanes. Such flexible chains become loosely entangled when molecular weight is high, which results in PDMS having an unusually high level of viscoelasticity.

Mechanical properties

PDMS is viscoelastic, meaning that at long flow times (or high temperatures), it acts like a viscous liquid, similar to honey. However at short flow times (or low temperatures) it acts like an elastic solid, similar to rubber. In other words, if you leave some PDMS on a surface overnight (long flow time), it will flow to cover the surface and mold to any surface imperfections. However if you roll the same PDMS into a sphere and throw it onto the same surface (short flow time), it will bounce like a rubber ball.

Hardened PDMS cylinder on the glass of a stereomicroscope light.

Although the viscoelastic properties of PDMS can be intuitively observed using the simple experiment described above, they can be more accurately measured using dynamic mechanical analysis. This involves using a specialized instrument to determine the material's flow characteristics over a wide range of temperatures, flow rates, and deformations. Because of PDMS's chemical stability, it is often used as a calibration fluid for this type of experiment.

The shear modulus of PDMS varies with preparation conditions, but is typically in the range of 100 kPa to 3 MPa. The loss tangent is very low (tan δ ≪ 0.001).[2]

Chemical compatibility

After polymerization and cross-linking, solid PDMS samples will present an external hydrophobic surface.[3] This surface chemistry makes it difficult for polar solvents (such as water) to wet the PDMS surface, and may lead to adsorption of hydrophobic contaminants. Plasma oxidation can be used to alter the surface chemistry, adding silanol (SiOH) groups to the surface. This treatment renders the PDMS surface hydrophilic, allowing water to wet (this is frequently required for, e.g. water-based microfluidics). The oxidized surface resists adsorption of hydrophobic and negatively charged species. The oxidized surface can be further functionalized by reaction with trichlorosilanes. Oxidized surfaces are stable for ~30 minutes in air, after a certain time hydrophobic recovery of the surface is inevitable independently of the surrounding medium whether it is vacuum, air or water.[4]

Solid PDMS samples (whether surface oxidized or not) will not allow aqueous solvents to infiltrate and swell the material. Thus PDMS structures can be used in combination with water and alcohol solvents without material deformation. However most organic solvents will diffuse into the material and cause it to swell,[3] making them incompatible with PDMS devices. Despite this, some organic solvents lead to sufficiently small swelling that they can be used with PDMS, for instance within the channels of PDMS microfluidic devices. The swelling ratio is roughly inversely related to the solubility parameter of the solvent. Diisopropylamine swells PDMS to the greatest extent, solvents such as chloroform, ether, and THF swell the material to a large extent. Solvents such as acetone, 1-propanol, and pyridine swell the material to a small extent. Alcohols and polar solvents such as methanol, glycerol and water do not swell the material appreciably.[5]

Applications

Many people are indirectly familiar with PDMS because it is an important (4%) component in Silly Putty, to which PDMS imparts its characteristic viscoelastic properties.[citation needed] The rubbery, vinegary-smelling silicone caulks, adhesives, and aquarium sealants are also well-known. PDMS is also used as a component in silicone grease and other silicone based lubricants, as well as in defoaming agents, mold release agents, damping fluids, heat transfer fluids, polishes, cosmetics, hair conditioners and other applications. PDMS has also been used as a filler fluid in breast implants, although this practice has decreased somewhat, due to safety concerns, despite some evidence that it may be protective against breast cancer.[6] It continues to be used in knuckle replacement implants, with good results. [citation needed]

Activated dimethicone, a mixture of polydimethylsiloxanes and silicon dioxide (sometimes called simethicone), is used in Over-the-counter drug as an anti-foaming agent and carminative.[citation needed]

As a food additive, it has the E number E900 and is used as an anti-foaming agent and an anti-caking agent.[citation needed]

PDMS is commonly used as a stamp resin in the procedure of soft lithography, making it one of the most common materials used for flow delivery in microfluidics chips. The process of soft lithography consists of creating an elastic stamp which enables the transfer of patterns of only a few nanometers in size onto glass, silicon or polymer surfaces. With this type of technique it is possible to produce devices which can be used in the areas of optic telecommunications or biomedical research. However, this process still can not be used for the industrial production of electronic components. In fact, the patterns are obtained by the process of stamping thanks to a shape (or stamp). This stamp is produced from the normal techniques of photolithography or electron-beam technology. The resolution depends on the mask used and can reach 6 nm[7].

In Bio-MEMS, soft lithography is used extensively for microfluidics in both organic and inorganic contexts. Silicon wafers are used to design channels, and PDMS is then poured over these wafers and left to harden. When removed, even the smallest of details is left imprinted in the PDMS. With this particular PDMS block, hydrophilic surface modification is conducted using RF Plasma techniques. Once surface bonds are disrupted, usually a piece of glass slide is placed on the activated side of the PDMS (the side with imprints). Once the bonds relax to their normal state, the glass is permanently sealed to the PDMS, thus creating a waterproof channel. With these devices, researchers can utilize various different surface chemistry techniques for different functions creating unique lab-on-a-chip devices for rapid parallel testing.

PDMS can be cross-linked into networks and is a commonly used system for studying the elasticity of polymer networks.[citation needed]

PDMS can be used in the treatment of head lice.[8]

Dimethicone is also used widely in skin moisturizing lotions, listed as an active ingredient whose purpose is "skin protectant." Some cosmetic formulations use dimethicone and related siloxane polymers in concentrations of use up to 15%. The Cosmetic Ingredient Review's (CIR) Expert Panel, has concluded that dimethicone and related polymers are "safe as used in cosmetic formulations" [1]

PDMS is also used in analytical chemistry as a component of some types of SPME fibers. PDMS can be directly patterned by surface-charge lithography. [9]

PDMS in a modified form is used as an herbicidal penetrant[10].

PDMS has been used in the aerospace industry as a heat tile on reentry vehicles[2]

See also

References

  1. ^ Linear Polydimethylsiloxanes. Joint Assessment of Commodity Chemicals. Vol. 26. p. 1. ISSN 0773-6339-26. {{cite book}}: Check |issn= value (help); Cite has empty unknown parameters: |lastauthoramp=, |laysummary=, |chapterurl=, |month=, and |separator= (help); Unknown parameter |laydate= ignored (help)
  2. ^ Lotters, J. C.; Olthuis, W.; Veltink, P. H.; Bergveld, P. "The mechanical properties of the rubber elastic polymer polydimethylsiloxane for sensor applications" J Micromech Microeng 1997, 7, (3), 145-147.
  3. ^ a b McDonald, J. C.; Duffy, D. C.; Anderson, J. R.; Chiu, D. T.; Wu, H.; Schueller, O. J. A.; Whitesides, G. M. "Fabrication of microfluidic systems in poly(dimethylsiloxane)" Electrophoresis 2000, 21, (1), 27-40.
  4. ^ H. Hillborg, J.F. Ankner, U.W. Gedde, G.D. Smith, H.K. Yasuda and K. Wikstrom, "Crosslinked polydimethylsiloxane exposed to oxygen plasma studied by neutron reflectometry and other surface specific techniques" Polymer 2000, 41, (18), 6851–6863.
  5. ^ Lee, J. N.; Park, C.; Whitesides, G. M. "Solvent Compatibility of Poly(dimethylsiloxane)-Based Microfluidic Devices" Anal. Chem. 2003, 75, (23), 6544-6554.
  6. ^ Implants may lower cancer risk
  7. ^ Waldner, Jean-Baptiste (2008). Nanocomputers and Swarm Intelligence. London: ISTE John Wiley & Sons. pp. 92–93. ISBN 1847040020.
  8. ^ Burgess, Ian F. (2009), "The mode of action of dimeticone 4% lotion against head lice, Pediculus capitis", BMC Pharmacology, 9 (3), doi:10.1186/1471-2210-9-3, retrieved 2009-04-19{{citation}}: CS1 maint: unflagged free DOI (link)
  9. ^ Surface-charge lithography for direct pdms micro-patterning S. Grilli, V. Vespini, P. Ferraro Langmuir 24, 13262-13265 (2008). http://dx.doi.org/10.1021/la803046j
  10. ^ "Pulse Penetrant..." Retrieved 3 March 2009.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Polydimethylsiloxane&oldid=318410096"