Jump to content

Kapton

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Citation bot (talk | contribs) at 06:18, 5 February 2021 (Alter: url. URLs might have been internationalized/anonymized. Add: bibcode, author pars. 1-1. Removed parameters. Some additions/deletions were actually parameter name changes. | You can use this bot yourself. Report bugs here. | Suggested by Abductive | Category:Dielectrics | via #UCB_Category 9/57). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Structure of poly-oxydiphenylene-pyromellitimide
Kapton insulating pads for mounting electronic parts on a heat sink

Kapton is a polyimide film developed by DuPont in the late 1960s that remains stable across a wide range of temperatures, from −269 to +400 °C (−452 to 752 °F; 4 to 673 K).[1][2] Kapton is used in, among other things, flexible printed circuits (flexible electronics) and space blankets, which are used on spacecraft, satellites, and various space instruments.

The chemical name for Kapton K and HN is poly (4,4'-oxydiphenylene-pyromellitimide). It is produced from the condensation of pyromellitic dianhydride and 4,4'-oxydiphenylamine. Kapton synthesis is an example of the use of a dianhydride in step polymerization. The intermediate polymer, known as a "poly(amic acid)", is soluble because of strong hydrogen bonds to the polar solvents usually employed in the reaction. The ring closure is carried out at high temperatures (200–300 °C (392–572 °F; 473–573 K)).

Usage

Kapton tapes, three rolls of different widths

The thermal conductivity of Kapton at temperatures from 0.5 to 5 kelvin is rather high for such low temperatures, κ = 4.638×10−3 T0.5678 W·m−1·K−1.[3] This, together with its good dielectric qualities and its availability as thin sheets have made it a favorite material in cryogenics, as it provides electrical insulation at low thermal gradients. Kapton is regularly used as an insulator in ultra-high vacuum environments due to its low outgassing rate.[4]

Aircraft

Kapton-insulated electrical wiring has been widely used in civil and military aircraft because it is lighter than other insulators and has good insulating and temperature characteristics. However, Kapton insulation ages poorly: an FAA study shows degradation in hot, humid environments,[5] or in the presence of seawater. It was found to have very poor resistance to mechanical wear, mainly abrasion within cable harnesses due to aircraft movement. Many aircraft models have had to undergo extensive rewiring modifications—sometimes completely replacing all the Kapton-insulated wiring—because of short circuits caused by the faulty insulation. Kapton-wire degradation and chafing due to vibration and heat has been implicated in multiple crashes of both fixed wing and rotary wing aircraft, with loss of life.[6]

Spacecraft

Aluminized Kapton thermal cover was used on the Ultra Heavy Cosmic Ray Experiment

The descent stage of the Apollo Lunar Module, and the bottom of the ascent stage surrounding the ascent engine, were covered in blankets of aluminized Kapton foil to provide thermal insulation. During the return journey from the Moon, Apollo 11 astronaut Neil Armstrong commented that during the launch of the Lunar Module ascent stage, he could see "Kapton and other parts on the LM staging scattering all around the area for great distances." [7]

JWST sunshield, made of Kapton

According to a NASA internal report, space shuttle "wires were coated with an insulator known as Kapton that tended to break down over time, causing short circuits and, potentially, fires."[8] The NASA Jet Propulsion Laboratory has considered Kapton as a good plastic support for solar sails because of its long duration in the space environment.[9]

NASA's New Horizons spacecraft used Kapton in an innovative "Thermos bottle" insulation design to keep the craft operating between 10–30 °C (50–86 °F) throughout its more than nine-year, 3 billion mile journey to rendezvous with the dwarf planet Pluto on 14 July 2015.[10] The main body is covered in lightweight, gold-colored, multilayered thermal insulation which holds in heat from operating electronics to keep the spacecraft warm. The thermal blanketing–18 layers of Dacron mesh cloth sandwiched between aluminized Mylar and Kapton film–also helped to protect the craft from micrometeorites.[11]

The sunshield of the James Webb Space Telescope is also made of aluminized Kapton.[12]

The crew aboard the International Space Station used Kapton tape to temporarily repair a slow leak in a Soyuz spacecraft attached to the Russian segment of the orbital complex in August 2018.[13] It was used again in October 2020 to temporarily seal a leak in the transfer chamber of the Zvezda Service Module of the ISS.[14]

X-rays

Kapton is also commonly used as a material for windows of all kinds at X-ray sources (synchrotron beam-lines and X-ray tubes) and X-ray detectors. Its high mechanical and thermal stability and high transmittance to X-rays make it the preferred material. It is also relatively insensitive to radiation damage.[15]

Electronics manufacturing

Kapton tape (yellow) used to insulate the leads of a battery cell in a bluetooth headset.

Due to its large range of temperature stability, and its electrical isolation ability, Kapton tape is usually used in electronic manufacturing as an insulation and protection layer on electrostatic sensitive and fragile components. As it can sustain the temperature needed for a reflow soldering operation, its protection is available throughout the whole production process, and Kapton is often still present in the final consumer product.

3D printing

Kapton and ABS adhere to each other very well, which has led to widespread use of Kapton as a build surface for 3D printers. Kapton is laid down on a flat surface and the ABS is extruded onto the Kapton surface. The ABS part being printed will not detach from the build platform as it cools and shrinks, a common cause of print failure by warping of the part.[16] A more durable alternative is to use a polyetherimide surface.[17]

Researchers have devised a method to 3D-print polyimide material including Kapton.[18] The precursors to Kapton were mixed into an ultraviolet-treated gel for extrusion printing, and the result is baked in an oven at 400 °C to yield the final result.[19]

Trademark

Kapton is a registered trademark of E. I. du Pont de Nemours and Company.[20]

References

  1. ^ "DuPont Circuit & Packaging Materials Awarded U.S. Patents for Matte Black Film and Coverlay". 15 November 2013. Retrieved 28 May 2015. DuPont invented Kapton® polyimide film over 45 years ago
  2. ^ Navick, X.-F.; Carty, M.; Chapellier, M.; Chardin, G.; Goldbach, C.; Granelli, R.; Hervé, S.; Karolak, M.; Nollez, G.; Nizery, F.; Riccio, C.; Starzynski, P.; Villar, V. (2004). "Fabrication of ultra-low radioactivity detector holders for Edelweiss-II". Nuclear Instruments and Methods in Physics Research Section A. 520 (1–3): 189–192. Bibcode:2004NIMPA.520..189N. doi:10.1016/j.nima.2003.11.290.
  3. ^ Jason Lawrence, A. B. Patel and J. G. Brisson (2000). "The thermal conductivity of Kapton HN between 0.5 and 5 K". Cryogenics. 40 (3): 203–207. Bibcode:2000Cryo...40..203L. doi:10.1016/S0011-2275(00)00028-X.
  4. ^ Peter Kittel (30 September 1998). Advances in Cryogenic Engineering. Birkhäuser. pp. 1366–. ISBN 978-0-306-45807-1. Retrieved 29 April 2012.
  5. ^ FAA insulation ageing test results. DOT/FAA Tech Report AR-08/2, January 2008. Retrieved on 23 August 2013
  6. ^ Fatal helicopter crash caused by Kapton wiring www.military.com Retrieved 17 February 2015.
  7. ^ Apollo 11 Flight Journal – Day 6 part 4: Trans-Earth Injection. History.nasa.gov (15 March 2011). Retrieved on 2012-04-28.
  8. ^ High Tech in the 1970s, Shuttles Feel Their Age. New York Times (25 July 2005)
  9. ^ Jerome L. Wright (1 January 1992). Space Sailing. Taylor & Francis US. pp. 100–. ISBN 978-2-88124-842-9. Retrieved 28 April 2012.
  10. ^ NASA New Horizons Pluto Mission, Mission Design Archived 8 June 2015 at the Wayback Machine Retrieved 23 April 2015
  11. ^ NASA, New Horizons Mission, Thermal Control
  12. ^ "Sunshield Membrane Coatings" page at the JWST website. Ngst.gsfc.nasa.gov. Retrieved on 23 May 2017.
  13. ^ "ISS Status blog" at NASA website. Retrieved on 30 August 2018.
  14. ^ Neilson, Susie (19 October 2020). "Space-station crew members just found an elusive air leak by watching tea leaves float in microgravity". Business Insider.
  15. ^ Janez Megusar (1997). "Low temperature fast-neutron and gamma irradiation of Kapton polyimide films". Journal of Nuclear Materials. 245 (2–3): 185–190. Bibcode:1997JNuM..245..185M. doi:10.1016/S0022-3115(97)00012-3.
  16. ^ "Bed Surfaces: Applying Kapton Tape". MatterHackers.
  17. ^ "Kapton or PEI? What's Better for Desktop 3D Printing?". Fabbaloo.
  18. ^ Hegde, Maruti; Meenakshisundaram, Viswanath; Chartrain, Nicholas; Sekhar, Susheel; Tafti, Danesh; Williams, Christopher B.; Long, Timothy E. (19 June 2017). "3D Printing All‐Aromatic Polyimides using Mask‐Projection Stereolithography: Processing the Nonprocessable". Advanced Materials. 29 (31). 1701240. doi:10.1002/adma.201701240. PMID 28626968. {{cite journal}}: Unknown parameter |lay-date= ignored (help); Unknown parameter |lay-source= ignored (help); Unknown parameter |lay-url= ignored (help)
  19. ^ Herzberger, Jana; Meenakshisundaram, Viswanath; Williams, Christopher B.; Long, Timothy E. (4 April 2018). "3D Printing All-Aromatic Polyimides Using Stereolithographic 3D Printing of Polyamic Acid Salts". ACS Macro Letters. 7 (4): 493–497. doi:10.1021/acsmacrolett.8b00126.
  20. ^ "Kapton Trademark". United States Patent and Trademark Office. USPTO. Retrieved 3 March 2017.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Kapton&oldid=1004951775"