Chevrolet Corvair

Chevrolet Corvair
1964 Chevrolet Corvair Monza
Overview
Manufacturer	Chevrolet Division of General Motors
Production	1959–1969
Model years	1960–1969
Assembly	Willow Run, MI Kansas City, KS Oakland, CA Van Nuys, CA St Louis, MO Flint, MI Oshawa, Ontario Mexico City (CKD) Caracas, Venezuela (CKD) Bienne, Switzerland (CKD) Antwerp, Belgium (CKD) Copenhagen, Denmark Port Elizabeth, South Africa (CKD)
Body and chassis
Class	Compact car
Layout	RR layout
Powertrain
Engine	Flat-six

The Corvair's air-cooled rear-mounted flat-6 engine

The Chevrolet Corvair is a compact automobile which was produced by the Chevrolet division of General Motors for the 1960–1969 model years. It was the only American designed, mass-produced passenger car to feature a rear-mounted air-cooled engine.

The Corvair range included a two-door coupe, convertible, four-door sedan, and four-door station wagon body styles, as well as in passenger van, commercial van, and pickup truck derivatives. The range competed with imported cars such as the original Volkswagen Beetle, as well as the Ford Falcon, Plymouth Valiant, and Studebaker Lark, that were new entries in the compact car market segment that was established in the U.S. by the 1950 Nash Rambler, which was reintroduced in 1958 as the Rambler American.

The Corvair's legacy was affected by controversy surrounding its handling, which led to its inclusion in Ralph Nader's Unsafe at Any Speed. Subsequently, in 1972, Texas A&M University conducted a safety commission report on the Corvair for the National Highway Traffic Safety Administration; it found that the 1960–1963 Corvairs possessed no greater potential for loss of control than its contemporaries in extreme situations.

History

In 1952, Edward N. Cole, known as Ed Cole, was promoted to chief engineer of the Chevrolet Motor Division. Four years later, in July 1956, he was named general manager of Chevrolet — GM's largest automotive division — and a vice president of General Motors. At Chevrolet, Cole pushed for many of the major engineering and design advancements introduced in the Chevrolet car and truck lines between 1955 and 1962. He was the moving force behind the development and production of the rear-engined, air-cooled Corvair. Despite its infamous history, the Corvair was a ground-breaking small car in its day. As chief engineer, he was heavily involved in the development of the Corvette sports car. He is also known as the "father" of the small block Chevy V8, one of the most celebrated engines in automotive history.

Until 1960, the "Big Three" domestic auto manufacturers (General Motors, Ford, and Chrysler) produced only one basic size of passenger cars: large. However, a successful modern "compact car" market segment was established in the U.S. by the 1950 Nash Rambler. Moreover, imports from Europe, such as Volkswagen, Renault, and Fiat, showed that there was demand in the U.S. for small cars, often as a second car or an alternative for budget-minded consumers. While the "Big Three" continued to introduce ever-larger cars during the 1950s, the newly formed American Motors Corporation (AMC) focused its business strategy on smaller-sized and fuel-efficient automobiles, years before there was a real need for them. Because it was a small company compared to the Big Three U.S. automakers, AMC positioned itself as a "dinosaur-fighter" and its compact-sized Rambler models rose to third place among domestic automobile sales. American Motors also reincarnated its predecessor company's smallest Nash model as the "new" 1958 Rambler American for a second model run, an almost unheard of phenomenon in automobile history.

During 1959 and 1960, the Big Three automakers planned to introduce their own "compact" cars. Most of these designs were scaled-down versions of the conventional American car, using four- or six-cylinder engines instead of V8s, and with bodies about 20% smaller than their standard cars.

An exception to this strategy was the Chevrolet Corvair. Led by General Manager Cole, Chevrolet designed a revolutionary new car. It was powered by an air-cooled horizontal six-cylinder engine made almost entirely out of aluminum. The engine was mounted in the rear of the car, driving the rear wheels through a compact automatic transaxle. Suspension was independent at all four wheels. There was no conventional frame, it was the first Unibody built by Fisher Body. The tires were an entirely new wide low-profile design. The styling was unconventional for Detroit: subtle and elegant, with no tailfins or chrome grille. Its engineering earned numerous patents, while Time magazine put Ed Cole and the Corvair on the cover, and Motor Trend named the Corvair as the 1960 "Car of the Year".

Overview

The Corvair's sales exceeded 200,000 for each of its first six model years. The rear-engine design offered packaging and economy advantages, providing the car with a lower silhouette, flat passenger compartment floor, removing the need for power assists, and offered improvements in ride quality, traction, and braking balance. The design also attracted customers of other makes, primarily imports. The Corvair stood out, with engineering significantly different from other American offerings. It used GM's Z-body, with design and engineering that advanced the rear-engine, rear-wheel drive layout pioneered by cars including the Tatra 77, Tucker Torpedo, Porsche 356, Volkswagen Beetle, Renault Dauphine, and NSU Prinz—and employed by the concurrent and short-lived Hino Contessa.

The Corvair's powerplant was an aluminum air-cooled 140 cu in (2.3 L) flat-six (later enlarged, first to 145 and then to 164 cubic inches). The first Corvair engine produced 80 hp (60 kW; 81 PS). Power peaked with the 1965–66 turbocharged 180 hp (134 kW; 182 PS) Corsa engine option. The first generation model's swing axle rear suspension, invented and patented by engineer Edmund Rumpler, offered a comfortable ride but raised safety concerns associated with the car's handling stability, and was replaced in 1965 with a fully independent rear suspension similar to the Corvette Sting Ray.

The Corvair represented several breakthroughs in design for mass-produced Detroit vehicles, with 1,786,243 cars produced between 1960 and 1969.

First generation (1960–1964)

First generation
Chevrolet Corvair convertible
Overview
Production	1959–1964
Model years	1960-1964
Body and chassis
Class	Compact car
Body style	2-door convertible 2-door coupe 4-door sedan 4-door station wagon 6-door van 8-door van 2-door pickup truck
Layout	RR layout
Platform	Z-body
Related	Pontiac Tempest Oldsmobile F-85 Buick Special
Powertrain
Engine	2,296 cc (2.3 L) Flat-6 2,375 cc (2.4 L) Flat-6 (1961–63) 2,683 cc (2.7 L) (1964)
Transmission	3-speed manual 4-speed manual 2-speed Powerglide automatic
Dimensions
Wheelbase	108 in (2,743 mm)
Length	180 in (4,572 mm)
Width	66.9 in (1,699 mm)

The 1960 Corvair 569 and 769 series four-door sedans were conceived as thrift cars offering few amenities in order to keep the price competitive, with the 500 (standard model) selling for under $2,000. Powered by the Turbo Air 6 engine 80 hp (60 kW; 81 PS) and three-speed manual or optional extra cost two-speed Powerglide automatic transmission, the Corvair was designed to have comparable acceleration to the six-cylinder full-size Chevrolet Biscayne. The Corvair's unique design included the "Quadri-Flex" independent suspension and "Unipack Power Team" of engine, transmission and rear axle combined into a single unit. Similar to designs of European cars such as Porsche, Volkswagen, Mercedes-Benz and others, quadri-flex used coil springs at all four wheels with independent rear suspension arms incorporated at the rear. Specially designed 6.5 in by 13 in. 4-ply tires mounted on 13 inch wheels with 5.5 in. width were standard equipment. Available options included RPO 360, the Powerglide two-speed automatic transmission ($146), RPO 118, a Gasoline Heater ($74), RPO 119, an AM tube radio ($54), and by February 1960 the rear folding seat (formerly $32) was standard. Chevrolet produced 47,683 of the 569 model and 139,208 769 model deluxe sedans in 1960. In January 1960, two two-door coupe models were introduced designated as the 527 and 727 models. Following the success of the "Mr. and Mrs." Monza styling concept cars at the 1960 Chicago Auto Show, management approved the neatly appointed bucket-seat trim of the 900 series Monza. This model began arriving at showroom floors in April of 1960. Despite their late January introduction of the coupe, these cars sold very well; about 14,628 base model 527 coupes, 36,562 727 deluxe coupes and 11,926 927 Monza club coupes, making the coupe one of the most popular Corvairs.

Sales figures revealed to Chevrolet management that the Corvair was more of a specialty car than a competitor to the conventionally designed Ford Falcon or Chrysler's Valiant. Corvair was not as competitive in the economy segment and Chevrolet began a design program that resulted in a compact car with a conventional layout, the Chevy II, for the 1962 model year.

An available option on the Corvair introduced in February 1960 was RPO 649, a more powerful engine, the Super Turbo Air. Super Turbo Air was rated at 95 hp (71 kW; 96 PS) at 4,800 rpm and 125 ft.lbs. at 2,800 rpm due to a revised camshaft, revised cylinder heads with dual springs, and a lower restriction muffler with a 2" outlet. This option was available in any Corvair model. However, in 1960, RPO 649 was not available with RPO 360, the powerglide automatic transmission.

The advertised February introduction of a fully synchronized, four-speed transmission RPO 651 was postponed until the 1961 model year due to casting problems with the aluminum three speed transmission case which resulted in technical service bulletins to dealers advising of potential for differential failure due to external leaks at the front of the transmission's counter gear shaft. The revision of the four speed transmission designated for 1961 introduction incorporated a cast iron case and a redesign of the differential pinion shaft to interface with a longer transmission output shaft and a concentricity pilot for the revised transmission case. These are among many of the course corrections undertaken by Chevrolet by the end of the 1960 model year.

The Corvair was Motor Trend magazine's Car of the Year for 1960.

The 1961 Monza was heavily promoted and referred to as "the poor man's Porsche" in various car magazines. The Monza series expanded with a four-door sedan body style in addition to the two-door coupe, and garnered about 144,000 sales.

1960 Chevrolet Corvair

1961 Corvair 500 Lakewood station wagon

A station wagon body-style, marketed as the Lakewood joined the lineup in 1961 with its engine located under the cargo floor and offering 68 ft³ (1.9 m³) of cargo room; 58 ft³ in the main passenger compartment, and another 10 ft³ in the front trunk. The Corvair engine received its first size increase to 145 cu in (2.4 L) via a slight increase in bore size and was rated at 98 hp (73 kW; 99 PS). The base engine was still rated at 80 hp (60 kW; 81 PS) when paired with the manual transmissions and 84 hp (63 kW; 85 PS) when mated to the optional automatic transmission in Monza models. To increase luggage capacity in the front trunk, the spare tire was relocated to the engine compartment (in cars not ordered with air-conditioning) and new "direct air" heater directed warmed air from the cylinders and heads to the passenger compartment. The gasoline heater remained available as an option through 1963. Factory air conditioning was offered as a mid-1961 option introduction. The condenser lay flat atop the horizontal engine fan. A large, green-painted reverse rotation version of the standard GM Frigidaire air conditioning compressor was used, and an evaporator housing was added under the dash with integrated outlets surrounding the radio housing. Air conditioning was not available on wagons, Greenbrier/Corvair 95, or the turbocharged models introduced later, due to space conflicts in those models. Chevrolet also introduced the Corvair 95 line of light-duty trucks, which used the Corvair Powerpack and are forward-control, or "cab over", with the driver sitting over the front wheels, as in the Volkswagen Type 2.

The Greenbrier Sportswagon used the same body as the "Corvan 95" panel van with the side windows option, but was marketed as a station wagon and was available with trim and paint options similar to the passenger cars. The "Corvan 95" model was also built in pickup versions; the Loadside was a fairly typical pickup of the era, except for the rear engine, forward controls, and a pit in the middle of the bed. The more popular Rampside, which had a unique large fold-down ramp on the side of the pickup bed making it easy to load wheeled items.

The Corvair Spyder turbocharged engine

In 1962 Chevrolet introduced the Corvairs with few changes at the beginning of the year. The bottom line 500 series station wagon was dropped and the 700 became the base station wagon. The "Lakewood" name was dropped. The ever popular Monza line then took on a wagon model to round out the top of the line. In Spring of 1962 Chevrolet really committed itself to the sporty image they had created for the Corvair by finally introducing a Convertible version and then offering a high performance 150 hp (112 kW; 152 PS) turbocharged "Spyder" option for Monza coupes and convertibles, making the Corvair the first production automobile to come with a turbocharger as a factory option, with the Oldsmobile F-85 Turbo Jetfire a few weeks later in 1962. Corvair station wagons were discontinued at that point in favor the new Corvair Convertible and Chevy II (built at the same assembly plant). The slow selling Loadside pickup was discontinued at the end of the model year. The rest of the Corvair 95 line of Forward Control vehicles continued on. Optional equipment included Metallic brake linings and a heavy duty suspension consisting of a front anti-roll bar, rear axle limit straps, revised spring rates and recalibrated shock absorbers. The Turbocharged Spyder equipment group featured a multi-gauge instrument cluster which included a tachometer, cylinder head temperature and intake manifold pressure gauges, Spyder fender script and Turbo logo deck emblems in addition to the high performance engine.

The Monza Coupe was the most popular model with 151,738 produced out of 292,531 total Corvair passenger car production for 1962. The Corvair was fast becoming the darling of the sporty car crowd. Many aftermarket companies offered a vast array of accessories for the Corvair, everything from imitation front grilles to serious performance upgrades such as additional carburetors, superchargers and performance exhaust and suspension upgrades. One of America's most successful race drivers, John Fitch chose the Corvair as the basis for his "Sprint" models. They were created at his shop in Connecticut by adding various performance improvements along with unique styling touches. Individual components were also available through his mail-order business. Several Chevrolet dealers became authorized Sprint dealers able to install his conversions as well.

The 1963 model year saw the optional availability of a long 3.08 gear for improved fuel economy, but the Corvair otherwise remained largely carryover with minor trim and engineering changes. Self-adjusting brakes were new for 1963. The Monza line was really proving its worth. Of all the Corvairs sold in 1963 fully 80% were Monzas. The Convertible model counted for over 20% of all the Monzas sold. Sporty image means big profits.

For 1964 significant engineering changes occurred, while the model lineup and styling remained relatively unchanged. The engine displacement was increased from 145 to 164 cu in (2.4 to 2.7 L) by an increase in stroke; the base engine power increased from 80 to 95 hp (60 to 71 kW; 81 to 96 PS), and the high performance engine increased from 95 to 110 hp (71 to 82 kW; 96 to 112 PS). The Spyder engine rating remained at 150 hp (112 kW; 152 PS) despite the displacement increase of the engine. 1964 saw an improvement in the car's swing axle rear suspension with the addition of a transverse leaf spring along with softer rear coil springs designed to diminish rear roll stiffness and foster more neutral handling attributes. Spring rates could now be softer at both ends of the car compared to previous models. The heavy duty suspension was no longer optional, although all models now had a front anti-roll bar as standard. Brakes were improved with finned rear drums. The remaining pickup, the Rampside, was discontinued at the end of the model year.

Second generation (1965–1969)

Second generation
1969 Chevrolet Corvair Monza convertible
Overview
Production	1964–1969
Model years	1965–1969
Body and chassis
Class	Compact car
Body style	2-door convertible 2-door hardtop 4-door hardtop (1965–67) 6-door van (1965)
Layout	RR layout
Platform	Z-body
Powertrain
Engine	2,683 cc (2.7 L) Flat-6
Transmission	3-speed manual 4-speed manual 2-speed Powerglide automatic
Chronology
Successor	Chevrolet Camaro

1967 Chevrolet Corvair Monza Front

1967 Chevrolet Corvair Monza Rear

A dramatic redesign of the Corvair came in 1965. The new body showed influence from the Corvette Stingray and the 1963 Buick Riviera. The mild coke bottle styling set the trend for GM cars for the next fifteen years, foreshadowing the 1967 Camaro. For the first time, none of the passenger cars had a "B" pillar, making all closed models true hardtops. The 4-door hardtop model was the only compact ever available in the U.S. with this body style. The second generation's styling was rated timeless when new, and considered contemporary today in comparison to the first generation. A new fully independent suspension, similar in design to the Corvette, replaced the original swing axle rear suspension. However, the Corvair used coil springs at each wheel instead of the Corvette's single transverse leaf spring unit.

Car and Driver magazine's David E. Davis Jr. showed enthusiasm for the 1965 Corvair in their October 1964 issue:

"And it is here too, that we have to go on record and say that the Corvair is — in our opinion — the most important new car of the entire crop of '65 models, and the most beautiful car to appear in this country since before World War II." "When the pictures of the '65 Corvair arrived in our offices, the man who opened the envelope actually let out a great shout of delight and amazement on first seeing the car, and in thirty seconds the whole staff was charging around, each wanting to be the first to show somebody else, each wanting the vicarious kick of hearing that characteristic war-whoop from the first-time viewer." "Our ardor had cooled a little by the time we got to drive the cars — then we went nuts all over again. The new rear suspension, the new softer spring rates in front, the bigger brakes, the addition of some more power, all these factors had us driving around like idiots — zooming around the handling loop dragging with each other, standing on the brakes — until we had to reluctantly turn the car over to some other impatient journalist ... The '65 Corvair is an outstanding car. It doesn't go fast enough, but we love it."

The standard 95 hp (71 kW; 96 PS) and optional 110 hp (82 kW; 112 PS) engines were carried forward from 1964. The previous 150 hp (112 kW; 152 PS) Spyder engine was replaced by the normally aspirated 140 hp (104 kW; 142 PS) for the new Corsa. The engine was unusual in offering four single-throat carburetors, to which were added larger valves and a dual exhaust system. A 180 hp (134 kW; 182 PS) turbocharged engine was optional on the Corsa, which offered either standard three-speed or optional (US$92) four-speed manual transmissions. The 140 hp (104 kW; 142 PS) engine was optional on 500 and Monza models with manual or Powerglide transmissions.

Many new refinements appeared on the beautiful new 1965 redesign. The Corsa came standard with an instrument panel featuring a 140 mph (230 km/h) speedometer with resettable trip odometer, a 6,000 rpm tachometer, cylinder head temperature gauge, analog clock with a sweeping second hand, a manifold vacuum/pressure gauge and fuel gauge. A much better heater system, larger brakes borrowed from the Chevelle, a stronger differential ring gear, a Delcotron alternator (replacing the generator), and significant chassis refinements were made. AM/FM stereo radio, in-dash All Weather Air Conditioning, telescopically adjustable steering column, and a Special Purpose Chassis Equipment ("Z17") handling package, consisting of a special performance suspension and quick ratio steering box, were significant new options for 1965.

By this time, the station wagon, panel van, and pickup body styles had all been dropped and 1965 was the last year for the Greenbrier window van, which was retained mainly for fleet orders, with 1,528 being built. In all, 235,528 Corvairs were built in 1965. Chevrolet replaced the Corvair-based vans with the Chevrolet Sportvan/GMC Handi-Van, which used a traditional front engine/rear drive axle borrowed from the Chevy II.

1968 Corvair Monza coupe with 110-hp engine

The 1966 lineup remained essentially unchanged from 1965. One change of note was a more robust four-speed synchromesh transmission using the standard Saginaw gear set with 3.11:1 first gear ratio used by other GM 6-cylinder vehicles. The steering column was changed to a two-piece design with universal joint, lessening the danger of intrusion during a front end collision. A plastic air dam was installed below the front valence panel to conceal the front suspension and underbody, and lessen crosswind sensitivity. In front, The "lock door" emblem (covering the lockset for the trunk lock) was changed from red to blue and featured a shorter bar. Air conditioned cars received a new condenser that was mounted in front of the engine, eliminating previous efficient but huge, awkward condenser that was mounted atop the engine, requiring its removal out of the way for most underhood servicing. The Corvair script nameplate was moved from atop the trunk lid to a position next to the driver's side headlight bezel. Sales began a decline as a result of Nader's book and the new Mustang that offered V8s up to 271 hp (202 kW; 275 PS) compared to Corvair's 180 hp (134 kW; 182 PS) top powertrain. and rumors of the upcoming "Panther'-the code name for the forthcoming Camaro, slated as a direct competitor for the Mustang. A decision was made to discontinue further development of the Corvair. Production for the model year was down to 103,743.

In 1967, the Corvair line was trimmed to the 500 and Monza Hardtop Coupes and Hardtop Sedans, and the Monza Convertible. This model year was the first with a collapsible steering column. A dual circuit master cylinder with warning light, nylon reinforced brake hoses, stronger steel (instead of aluminum) door hinges, "mushroomed" instrument panel knobs and a vinyl-edged day/night mirror were all made standard equipment. Chevrolet introduced a 50,000 mi (80,000 km) engine warranty on all Chevrolet models including the Corvair. Chevrolet was still actively marketing the Corvair in 1967, including color print ads and an "I Love My Corvair" bumper sticker campaign by dealers, but production and sales continued to fall off drastically. Only 27,253 copies were built.

In 1968, the four-door hardtop was discontinued, leaving three models—the 500 and Monza Hardtop Coupes and the Monza Convertible. Air conditioning was dropped as an option, due to concerns about thermal loading added by the now-standard Air Injection Reactor ("smog pump") which probably hurt sales as factory air became more popular generally in automobiles. The GM multiplex stereo system was also discontinued when new units changed wiring adapters; the Corvair's 9-pin connector would no longer fit the new units. Additional safety features, including side marker lights, and shoulder belts for closed models, were fitted per the federal government's requirements. Steering wheel for 500s was the same as the base Nova's, while Monzas got the same wheel as the Camaro. An Impala-style "Deluxe" steering wheel was optional. All advertising was virtually stopped and sales were down to 15,400.

The final model-year 1969 Corvairs were assembled with the Nova in Willow Run, Michigan, the same facility Corvairs had been built from the beginning. A total of 6,000 Corvairs were produced of which only 521 were Monza Convertibles. Corvair was the only 1969 GM car that did not get a locking steering column. Demand for Novas was high and a decision was made in November 1968 to move Corvair assembly to a special off-line area in the plant, dubbed the "Corvair Room", making Corvairs produced between that time and May 14, 1969 essentially hand-built by a dedicated Corvair team. Assembled bodies arrived from Fisher Body and awaited assembly in the off-line area.

End of production

Chevrolet had proposed a third generation (1970-on) Corvair, essentially a re-skin of the 1965–69 model resembling the 1973 GM A Body intermediates, particularly the 1973 Pontiac Grand Am, retaining Corvair proportions. Having passed the point of full scale clay models, Chevrolet stopped developing the model in early 1968. Unlike the Turbo Hydramatic 400, the Turbo Hydramatic 350 transmission, introduced in the 1968 Camaro and later adopted by most Chevrolet models had been configured for use in the third generation Corvair.
According to GM historian Dave Newell, Chevrolet had planned on ending Corvair production after the 1966 model year. Development and engineering changes were halted in 1966 on the year-old, redesigned second-generation cars with mainly federally mandated emissions and safety changes made thereafter.

The Corvair faced competition from the Ford Mustang, Chevy's own Camaro, and other pony cars. The car had been costly to produce, yet was not offered at a premium price; not a high profit earner for Chevrolet. An increasing lack of interest from the company, especially from Chevrolet's General Manager John DeLorean, and a complete absence of Corvair advertising after 1967 reflected the company's priorities, including promotion of three redesigned models for 1968—the Corvette, Chevelle, and Chevy II Nova.

The Corvair was referred to as "the phantom" by Car Life magazine in their 1968 Monza road test, and by 1969 Chevrolet's Corvair four-page brochure was "by request only". During its final year of production, 6,000 cars were produced.

Handling controversy

First-generation (1960–1963) Corvair handling characteristics became the subject of controversy when Ralph Nader addressed them in his 1965 book, Unsafe at Any Speed. GM had over 100 lawsuits pending in connection with crashes involving the Corvair, which subsequently became the initial material for Nader's investigations. The book highlighted crashes related to the Corvair's suspension and identified the Chevrolet suspension engineer who had fought management's decision to remove—for cost reasons—the front anti-sway bar installed on later models. Nader said during subsequent Congressional hearings, the Corvair is "the leading candidate for the un-safest-car title". Subsequently, Corvair sales fell from 220,000 in 1965 to 109,880 in 1966. By 1968 production fell to 14,800. Public response to the book played a role in the National Traffic and Motor Vehicle Safety Act in 1966.

A 1972 safety commission report conducted by Texas A&M University concluded that the 1960–1963 Corvair possessed no greater potential for loss of control than its contemporary competitors in extreme situations. The U.S. Department of Transportation (DOT) issued a press release in 1972 describing the findings of NHTSA testing from the previous year. NHTSA had conducted a series of comparative tests in 1971 studying the handling of the 1963 Corvair and four contemporary cars—a Ford Falcon, Plymouth Valiant, Volkswagen Beetle, and Renault Dauphine—along with a second-generation Corvair (with its completely redesigned, independent rear suspension). The 143-page report reviewed NHTSA's extreme-condition handling tests, national crash-involvement data for the cars in the test as well as General Motors' internal documentation regarding the Corvair's handling. NHTSA went on to contract an independent advisory panel of engineers to review the tests. This review panel concluded that "the 1960–63 Corvair compares favorably with contemporary vehicles used in the tests...the handling and stability performance of the 1960–63 Corvair does not result in an abnormal potential for loss of control or rollover, and it is at least as good as the performance of some contemporary vehicles both foreign and domestic." Former GM executive John DeLorean asserted in his 1979 book On a Clear Day You Can See General Motors that Nader's criticisms were valid.

Car and Driver magazine criticized Nader for ignoring drivers' failure to adapt their driving and vehicle-maintenance practices to the characteristics and requirements of the Corvair. None of the issues Nader raised were problems among owners of the Porsche 911, which had the same layout and similar suspension, nor with the less powerful Volkswagen Type 1 Beetle.

Journalist David E. Davis, in a 2009 article in Automobile Magazine, noted that despite Nader's claim that swing-axle rear suspension were dangerous, Porsche, Mercedes-Benz, and Volkswagen all used similar swing-axle concepts during that era.

Handling characteristics

1960–63 swing axle suspension

Swing axle suspension characteristics:
camber change on bumps, jacking on rebound

The first-generation Corvair featured a rear swing axle design similar to that of the Renault Dauphine and Volkswagen Beetle – a design which eliminates universal joints at the wheels and wherein the rear wheels are always perpendicular to the driveshafts. The design can allow rear tires to undergo large camber angle changes during fast cornering, leading to oversteer—a dynamically unstable condition where a vehicle can lose control and spin — and in extreme cases produce lift-off oversteer. Oversteer in both cases is due to more weight on the rear wheels than the front. Inertia would then cause the rear tires to lose traction and "spin". Understeer is common in front-engine cars, due to more weight, and inertia, on the front tires. Both conditions are dangerous when a car is driven at its cornering limits. Design options to ameliorate swing axle handling:

• Anti-roll bar: As a production option, engineers had advocated but management rejected the inclusion of a front anti-roll bar on the original 1960 Corvair, which would have ameliorated the car's handling – shifting weight transfer to the front outboard tire, considerably reducing rear slip angles—thereby avoiding potential oversteer.
• Tire pressure differential: As with the Renault Dauphine and pre-1968 Volkswagen Beetle, Corvair engineers relied on a cost-free tire pressure differential to eliminate oversteer characteristics – low front and high rear tire pressure–a strategy which induced understeer (increasing front slip angles faster than the rear). Nonetheless, the strategy offered a significant disadvantage: owners and mechanics could inadvertently but easily re-introduce oversteer characteristics by over-inflating the front tires (e.g., to typical pressures for other cars with other, more prevalent suspension systems).

While the Corvair offered competent handling, "the average buyer more accustomed to front-engined cars, did not take [into] account the car's different handling characteristics." Chevrolet made a succession of improvements to the first-generation Corvair suspension. For the 1962 model year, the front anti–roll bar became available as an option. For the 1964 model year, the front anti-roll bar became standard equipment and the rear suspension was modified to include a camber compensating, transverse-mounted leaf spring extending between the rear wheels to limit rear wheel camber change, and carrying much of the rear weight combined with softer coil springs.

For the 1965 model year, the Corvair received a fully independent rear suspension closely resembling that of the contemporary Corvette. The redesigned suspension reduced the rear roll center to half its previous height, using fully articulated half-axles that offered constant camber on the rear tires in all driving situations.

Reception

Time featured Ed Cole and the 1960 Corvair on its cover for the Corvair introduction in 1959 and said: "its fresh engineering is hailed as the forerunner of a new age of innovation in Detroit." Time reported in 1960: Chevrolet sold 26,000 Corvairs its first two days on the market, taking over 35% of Chevy's two-day total of 75,000. Chevrolet had intended to sell one Corvair for every five Chevrolets. By March 1960, the Corvair comprised 13% of Chevrolet's sales. Shortly after its introduction, the Corvair faced competition from the Ford Falcon and Mercury Comet and was plagued by problems—though according to a 1960 Time report, "many were the minor bugs that often afflict a completely new car." Problems included an engine cooling fan belt that tended to pop off its 2-axis pulleys (unless the fan ran constantly, the air-cooled engine would overheat and seize), carburetor icing and poor fuel mileage "which sometimes runs well under 20 m.p.g." The 1960 model gasoline heater was cited as a problem, which itself could consume up to a quart of gas an hour—with Chevrolet engineers quickly modifying the Corvair's carburetors to improve economy.

Motor Trend awarded the Corvair its "Car of the Year" award for 1960.

Greenbrier Sportswagon

Main article: Chevrolet Greenbrier

The Corvair also came in a van and pickup version, both rear loader and side loader form, besides a wagon and coupe.

Production notes

Year	Production	Base price	Notes
1960	253,268	US$1,984–2,238	500 and 700 4-door sedan are only models available at introduction; 500 and 700 Club Coupe become available January 1960, Monza Club Coupe introduced spring 1960 with 95 hp (71 kW) "Super Turbo Air" high performance engine option, and 4-speed transmission, gas heater optional, spare tire mounted in luggage compartment, central automatic choke. Sales impeded by U.S. Steel strike shortly after introduction, causing a shortage of new 1960 models. Monza is the first Chevrolet model with 'narrow' 1 in (25 mm) stripe whitewall tire.
1961	337,371	US$1,920–2,331	Lakewood station wagon, Greenbrier, Corvan, and Loadside and Rampside pickups added; 145 in³ engine and optional three-speed manual; spare tire now rear-mounted on models not equipped with mid-1961 All Weather Air Conditioning option. Manual choke. First full year of Monza production demonstrates its sales success, pushes Ford to develop Falcon Sprint and eventually Mustang to exploit the small sporty car market uncovered by Corvair Monza.
1962	336,005	US$1,992–2,846	Monza Convertible and Turbocharged Monza Spyder added mid-1962, heavy duty suspension optional with front anti roll bar, rear axle limit straps, positraction differential, new Monza full wheel covers, Kelsey Hayes knock off wire wheels added to options, Monza wagon becomes available, 500 wagon dropped- wagons lose 'Lakewood' designation. Station wagons discontinued mid-1962 to provide capacity for other Corvair and Chevy II models.
1963	288,419	US$1,982–2,798	Self adjusting brakes and small engine improvements (belt guides, improved oil cooler), new Monza rocker moldings, Loadside pickup discontinued.
1964	214,483	US$2,000–2,811	Larger 164 CID engine, improved rear suspension with added transverse leaf spring and revised coil springs, front stabilizer bar added as standard, finned rear brake drums, new optional full wheel covers-std. for Monza with specific centers, new Monza chrome rocker and wheel opening moldings, last year for Rampside pickup.
1965	247,092	US$2,066–2,665	Major redesign of the Corvair- all new Fisher Z body, hardtop styling for all models, 700 series discontinued, Corsa series replaces Monza Spyder series; Greenbrier discontinued mid-year after 1528 built; revised front and redesigned fully independent rear suspension, improved heater and air conditioning systems, numerous small engine and chassis refinements. Mid year introduction of Z17 'steering and suspension" option includes special springs with rates increased approximately 25%, special shock absorbers, a 16:1 steering box and special steering arms. New options include 140 hp (100 kW) engine, telescopic steering column, AM/FM, FM stereo, heavy duty oil bath air cleaner precleaner system with engine shrouding for dust control. Front Chevy emblem painted red.
1966	109,880	US$2,083–2,682	Improved 3 and 4-speed synchromesh manual transmissions; last year of Corsa model, Last year of Canadian production at Oshawa. Late 1965 modification to steering shaft adds a U-joint and floor reinforcement to reduce risks of column intrusion in collisions. Tire size upgraded to 7.00–13 from 6.50–13, with narrower .625 in (15.9 mm) whitewall. New "spoke" style wheel covers for all models with specific model centers. Front Chevy emblem now blue (remaining this color until the end of production). New optional equipment includes headrests, shoulder harnesses, 4-speaker Delco FM Stereo Multiplex, power rear antenna, 'Mag Style' (N96) wheelcovers. New, smaller condenser mounted behind the engine for air-conditioned cars. Four lap belts (2 front, 2 rear), padded instrument panel, larger taillight lenses, day/night rearview mirror, now standard on all models. Monzas and Corsas feature black crinkle finish on instrument panel.
1967	27,253	US$2,128–2,540	Last year for the four-door hardtop sedan, GM Energy Absorbing steering column, dual circuit brake system, stronger door hinges introduced. New safety three-spoke steering wheel standard. Four-way hazard flashers, lane-change turn signal control, additional padding on instrument panel cover, safety control knobs introduced. 110 hp (82 kW) engine is only optional engine at introduction; eventually 140 hp (100 kW) becomes available as Central Office Production Order in limited production as COPO 9551"B". New "safety" Powerglide shift knob, shoulder belt mount points added. New style standard hub caps for 500. Chrome ring inside taillight lenses widened. New options included Speed Warning, Delco Stereo Tape system. New thin-shell "Astro-bucket" front seats with new vinyl pattern standard on Monzas.
1968	15,399	US$2,243–2,626	Air Injection Reactor standard in all markets, 140 hp (100 kW) engine reintroduced as a regular production option, optional All Weather Air Conditioning discontinued, multiplex stereo option discontinued; fuel vapour return line and Ignition Key Warning buzzer new standard features. Front shoulder harnesses become standard after Jan 1, 1968, rear shoulder harnesses are optional all models. Side marker lights (clear in front with amber bulbs, red in rear) added to fenders on all models. New padding around central section of dash; thicker padding on top of dash, steering wheel spokes on Monzas now brushed aluminum (instead of chrome).
1969	6,000	US$2,528–2,641	Last year—production through May 1969; 521 Monza Convertibles of 6000 Corvairs produced; minor changes; improved clutch cable design on manual transmission cars, wider bucket seats with new head restraints, wider interior mirror, refined front brake hose design, Front side markers now feature amber lenses and clear bulbs (opposite from '68). 140 hp (100 kW) engine, F41 'special purpose suspension', N44 'quick ratio steering box' Positraction and telescopic steering column remain available. Interior window handles featured clear-colored knobs. Deluxe steering wheel option discontinued. New style ignition, door and trunk keys introduced. The last few months of production cars were hand-built on a special off-line area of the Willow Run plant.
Total	1,835,170

Production plants

All locations are cars only, except as noted:

• Willow Run 1960-69
• Kansas City 1960-61
• Oakland, CA 1960-63
• Van Nuys, CA 1963, 1965 & 1966
• St Louis, MO 1961-65 (FCs)
• Flint, MI 1961-64 (FCs)
• Oshawa, Ontario 1960-66
• Mexico City 1961-63 (CKD)
• Caracas, Venezuela 1960-62 (CKD)
• Bienne, Switzerland 1960-67 (CKD)
• Antwerp, Belgium 1960-67 (CKD)
• Copenhagen, Denmark 1960-61
• Port Elizabeth, South Africa 1960-62 (All 1960 CKD models)

Note that Willow Run, Kansas City, Oakland, and Van Nuys were Chevrolet assembly plants with adjacent Fisher Body plants.

St Louis and Flint were Chevrolet truck plants, although Chevy had full-size car plants in both cities and in St Louis the plants were adjacent.

Oshawa was operated solely by GM of Canada Ltd.

The CKD plants were operated by GM Overseas Operations (GMOO).

Model designations

500 - Base model Corvair with lowest trim level. Always came with rubber mats, bench seats, and very little trim.

700 - Next trim level up from the 500 model. These models also came with rubber mats and bench seats but had a little bit more trim (this model was discontinued after 1964).

Lakewood - Corvair Station Wagon (1961–62) available as a 500 or 700. The Monza wagon was available in 1962 and is not really a Lakewood. All window glass was specific to this model due to its taller roofline.

Monza (900) - The top of the trim line, just for 1960–63. In 1964, it was below the Monza Spyder, which was now its own model. For the 1965–66 model year, the Monza ranked below the Corsa in trim level. After the Corsa model was dropped, the Monza was once again the top of the Corvair line for 1967–69. Monzas usually came with bucket seats (although special bench seats were available in some years). Monzas always had carpets and special trim packages.

Spyder - The Monza Spyder was an option package during the 1962-63 model year, and in 1964 became a full-fledged model. It was equipped with a 150 hp (112 kW; 152 PS) turbocharged engine, "full instrumentation", special emblems, and all the "Monza" trim items.

Corsa - Top of the line sporty model for 1965–66. It was the only model available with the optional 180 hp (134 kW; 182 PS) turbocharged flat-6. The base engine was the new 4 carburetor 140 hp (104 kW; 142 PS) "big valve" engine. Corsas had "full instrumentation", special emblems, and trim with a special Argent silver painted rear cove area and pinstriping on the 1965 models. The optional 180 hp engine delivered an increase in power over the 1964 150 hp engine of the same displacement by slightly enlarging the carburetor, and increasing the size of the internal impeller and turbine blades.

Corvan (95) - Corvair panel van that was available 1961–64

Greenbrier - Windowed van that was available 1961–65

Rampside - Corvair pickup with a ramp on one side that was available 1961–64

Loadside - Rampside style but without the ramp which was available 1961–62

Deluxe - Option package of upgraded interior and trim available on some of the "van" models.

F.C. (Forward Control) - A "Chevy" term that applied to all Corvair 95 "van" models indicating that the driver and controls were forward of the front wheels.

Concept cars

Corvair Monza GT Concept

The Corvair spawned a number of innovative concept vehicles including the Corvair SS, Monza GT, Monza SS, Astro I. In Europe, Italian coachbuilder Bertone designed a very advanced one-off prototype for the 1963 Geneva Motor Show, The Corvair "Testudo". This was among the first designs of Giorgetto Giugiaro, the chief designer at Bertone at the time. Also Carrozzeria Pininfarina worked on a "Corvair Speciale".

The Chevrolet Corvair Monza GT coupe toured together with the Monza SS (Spyder) in early 1963, making a public appearance at the New York Auto Show. Although both cars were based on the Corvair drive train, each represented a futuristic development of the Corvair design. In the SS convertible, the engine (with a four-carburetor setup) was left in its stock location behind the transaxle, allowing a shorter (88 in (2,200 mm)) wheelbase. The Monza GT is housed at the GM's Heritage Center in Detroit.

A 1966 concept vehicle, the Electrovair II, was a 1966 Monza 4-door hardtop modified with a 532 volt 115-horsepower electric motor replacing the gasoline engine — following a 1964 version known as Electrovair I. With the 1966 model, silver-zinc batteries were used and placed in the trunk and engine compartment, and the body was slightly modified to accept the conversion. The car was handicapped by the high cost of the batteries ($160,000), a limited driving range (40–80 miles), and short battery life.

Racing and modified Corvairs

Yenko Stinger

A 1965 Yenko Stinger in a vintage race at Watkins Glen International

Don Yenko, who had been racing Corvettes, could not compete successfully against the Carroll Shelby Mustangs after they arrived on the scene; he therefore decided to race modified Corvairs, beginning with the 1966 model. As the stock Corvair did not fit into any of the SCCA categories, Yenko had to modify four-carburetor Corsas into "sports cars" by removing the back seat; in the process he introduced various performance improvements. As the SCCA required 100 cars to be manufactured to homologate the model for production racing, Yenko completed 100 Stingers in one month in 1965. Although all were white, as the SCCA required for American cars at the time, [the normal competition trim for U.S.-built cars was white with 2 blue stripes] there was a great deal of variety between individual cars; some had exterior modifications including fiberglass engine covers with spoilers, some did not; some received engine upgrades developing 160, 190, 220, or 240 hp (119, 142, 164, or 179 kW). All were equipped by the Chevrolet factory with heavy duty suspension, four speed transmission, quicker steering ratio, "positraction" limited-slip differentials (50 with 3.89 gears, and 50 with 3.55 when Chevrolet dropped the 3.89) and dual brake master cylinders (the first application of this by Chevrolet, to become stock equipment the next year). Because most of the engine cooling in air-cooled engines is done by circulating oil, an oil cooler was necessary for competition use, this was mounted externally on the rear body section above the left wheel.

The Stingers competed in Class D Production, which was dominated by the Triumph TR4, which was very quick in racing trim; however in its first race in January 1966, the Stinger was able to come in second by only one second. By the end of the 1966 season, Jerry Thompson had won the Central Division Championship and placed fifth in the 1966 Nationals, Dick Thompson, a highly successful Corvette race driver, had won the Northeast Division Championship, and Jim Spencer had won the Central Division Championship, with Dino Milani taking second place. The next year, however, Chevrolet dropped the Corsa line, and the Monza line was not initially available stock with the four carburetor engine; the engine was eventually offered as a special performance option, however, along with the 3.89 differential. The Monza instrumentation did not have a tachometer or head temperature gauges, which had to be separately installed. The SCCA, on the other hand, had relaxed its ruling regarding color, and the cars were available in red or blue. It is believed that only fourteen 1967 Stingers were built, but Dana Chevrolet, who distributed Stingers on the U.S. West Coast, ordered an additional three similar cars to be built to Stinger specifications, but with the AIR injection system to meet California emissions laws, with Yenko's permission. A total of 185 Stingers are believed to have been built, the last being YS-9700 built for Goodyear Tire and Rubber Company as a tire test vehicle in 1969–1970. Comedian, television star, and car enthusiast Tim Allen owned and raced Yenko Stinger #YS-043 until he sold it around June, 2009.

Fitch Sprint

Longtime roadracer John Fitch was particularly interested in the Corvair as the basis for a spirited road and track oriented car, due to its handling. The basic Sprint received only minor modifications to the engine, bringing it to 155 hp (116 kW; 157 PS), but upgrades to the shock absorbers and springs, adjustments to the wheel alignment, quicker steering ratio, alloy wheels, metallic brake linings, the obligatory wood-rimmed steering wheel (leather available for an additional $9.95) and other such minor alterations made it extremely competitive with European sports cars costing much more. Body options such as spoilers were available, but the most visually remarkable option was the "Ventop", a fiberglass overlay for the C-pillars and rear of the roof that gave the car a "flying buttress" profile.

Fitch went on to design and build a prototype of the Fitch Phoenix, a Corvair-based two-seat sports car, superficially resembling a smaller version of the Mako Shark based Corvette. With a total weight of 1,950 lb (885 kg), even with a steel body, and with the Corvair engine modified with Weber carburetors to deliver 175 hp (130 kW; 177 PS), the car delivered spirited performance for $8,760. The ability to produce automobiles on a small scale, along with Chevrolet's decision to terminate production of the Corvair, meant the end of Fitch's plan. He still retained the prototype, and occasionally exhibited it at car shows till his death. One June 1st 2014, the Fitch Phoenix when to auction at Bonhams in the Greenwich Concours and sold for 230,000 US dollars. The car is still in Connecticut with the new owner.

Winfield's cars: Reactor & Piranha

Gene Winfield, the automotive customizer. built two models in the mid 1960's that used the unique qualities of the lightweight and low Corvair engine.

The Reactor came when Winfield was tasked with showing the benefits of an aluminum bodied car. What he developed was an extremely low slung two seat mid-engine front wheel drive car. He used the 180 hp turbocharged engine from the Corvair Corsa. Other drivetrain components came from the Citroën DS, including the front wheel drive transaxle and Height adjustable suspension. Winfield was able to place this vehicle in the 1960's television programs Star Trek, Batman, and Bewitched.

A sports racing car - The Piranha - was developed around the same time, to demonstrate the use of a new plastic for the structural parts of the automobile - Cycolac ABS. This lightweight (1,400 lb) vehicle was developed in several generations, using a rear-mounted Corvair engine. Model car company Aluminum Model Toys began small scale production of actual cars through their division run by Gene Winfield. Winfield was able to obtain feature placement of this car on televison as well - in The Man from U.N.C.L.E.

Custom, dune buggies and aircraft

Corvair flat-six engines were a popular alternative to Volkswagen engines in dune buggy applications, and off-road racing. Some Corvair engines have also been used to power light aircraft.

Trans Am

A Corvair was driven by Spurgeon May and Donna Mae Mims in the Trans Am Series in 1966.

Design Influence

The First-generation Corvair (1960-1964) has been credited with influencing car design worldwide. Styled in GM's advanced styling studio in 1957, under the leadership of then director Ned Nickels, the compact design was made using cues from earlier Oldsmobile and Chevrolet models. The most notable design feature, it's high wrap-around beltline was "borrowed" by other carmakers not long after the Corvair's release. These cars included the BMW 1602/2002, NSU Prinz, Hillman Imp, Fiat 1300/00, Type34 Karmann Ghia, and the Mazda 800.

Similar cars

• Tatra 613
• Volkswagen Karmann Ghia Type 34
• Tucker_48

Pontiac Version

At the time the Corvair was being developed, a Pontiac version, named Polaris, was proposed. This car got as far as a styling markup before Pontiac division chief John Z. DeLorean turned it down, being suspicious of its air-cooled rear engine and drivetrain.

See also

• Chevrolet Corvair engine
• Chevrolet Corvair Powerglide
• Yenko Chevrolet
• Unsafe at Any Speed

References

Bibliography

• Cheetham, Craig (2005). The World's Worst Cars: From Pioneering Failures to Multimillion Dollar Disasters. Amber Books. ISBN 9781904687351.
• Flory, Jr., J. "Kelly" (2004). American Cars, 1960–1972: Every Model, Year by Year. McFarland. ISBN 978-0-7864-1273-0.
• Shattuck, Dennis, ed. (1963). Corvair – A complete Guide. A Car Life Special Edition. Chicago: Bond.

External links

• Article about the Chevrolet Corvair from the Vinson Collection at Hagley Library
• Filmstrip Advertisement for the Corvair from the Prelinger Archives at archive.org
• Template:Dmoz
• High Voltage Hot Rods Electrovair III Project