WiMAX

File:Wimax logo.gif

Official WiMax logo

WiMAX, the Worldwide Interoperability for Microwave Access, is a telecommunications technology aimed at providing wireless data over long distances in a variety of ways, from point-to-point links to full mobile cellular type access. It is based on the IEEE 802.16 standard, which is also called WirelessMAN. WiMAX allows a user, for example, to browse the Internet on a laptop computer without physically connecting the laptop to a router, hub or switch via an Ethernet cable. The name WiMAX was created by the WiMAX Forum, which was formed in June 2001 to promote conformance and interoperability of the standard. The forum describes WiMAX as "a standards-based technology enabling the delivery of last mile wireless broadband access as an alternative to cable and DSL."

Definitions of terms

The terms "fixed WiMAX", "mobile WiMAX", "802.16d" and "802.16e" are frequently used incorrectly. Correct definitions are:

802.16d

Strictly speaking, it has never existed as a standard. The standard is correctly called 802.16-2004. However, since this standard is frequently called 802.16d, that term is also used in this article to assist readability.

802.16e

Just as 802.16d has never existed, neither has 802.16e. 802.16d is an amendment to 802.16-2004, where802.16e is referred to as 802.16e-2005.

Fixed WiMAX

This is a phrase frequently used to refer to systems built using 802.16-2004 ('802.16d') and the OFDM PHY as the air interface technology.

Fixed WiMAX deployments do not cater for handoff between Base Stations, therefore the service provider cannot offer mobility.

Mobile WiMAX

A phrase frequently used to refer to systems built using 802.16e-2005 and the OFDMA PHY as the air interface technology. "Mobile WiMAX" implementations can be used to deliver both fixed and mobile services.

Uses

The bandwidth and reach of WiMAX make it suitable for the following potential applications:

• Connecting Wi-Fi hotspots with each other and to other parts of the Internet.
• Providing a wireless alternative to cable and DSL for last mile (last km) broadband access.
• Providing high-speed data and telecommunications services.
• Providing a diverse source of Internet connectivity as part of a business continuity plan. That is, if a business has a fixed and a wireless Internet connection, especially from unrelated providers, they are unlikely to be affected by the same service outage.
• Providing nomadic connectivity.

Broadband access

Many companies are closely examining WiMAX for "last mile" connectivity at high data rates. The resulting competition may bring lower pricing for both home and business customers, or bring broadband access to places where it has been economically unavailable. Prior to WiMAX, many operators have been using proprietary fixed wireless technologies for broadband services.

WiMAX access was used to assist with communications in Aceh, Indonesia, after the tsunami in December 2004. All communication infrastructure in the area, other than Ham Radio, was destroyed, making the survivors unable to communicate with people outside the disaster area and vice versa. WiMAX provided broadband access that helped regenerate communication to and from Aceh.

WiMAX was used by Intel to assist the FCC and FEMA in their communications efforts in the areas affected by Hurricane Katrina. [1]

Subscriber units

WiMAX subscriber units are available in both indoor and outdoor versions from several manufacturers. Self-install indoor units are convenient, but radio losses mean that the subscriber must be significantly closer to the WiMAX base station than with professionally-installed external units. As such, indoor-installed units require a much higher infrastructure investment as well as operational cost (site lease, backhaul, maintenance) due to the high number of base stations required to cover a given area. Indoor units are comparable in size to a cable modem or DSL modem. Outdoor units are roughly the size of a laptop PC, and their installation is comparable to a residential satellite dish.

With the advent of mobility ("16e"), there is an increasing focus on portable units. This includes handsets (similar to cellular smartphones) and PC peripherals (PC Cards or USB dongles). In addition, there is much emphasis from operators on consumer electronics devices (games terminals, MP3 players and the like); it is notable this is more similar to WiFi than 3G cellular technologies.

Mobile applications

Some cellular companies are evaluating WiMAX as a means of increasing bandwidth for a variety of data-intensive applications; Sprint Nextel announced in mid-2006 that it would invest about US$ 5 billion in a WiMAX technology buildout over the next few years. As of Friday, November 9, 2007, this project in partnership with Clearwire has been shelved, but the project could be revived with or without Clearwire once Sprint hires a new CEO.

In line with these possible applications is the technology's ability to serve as a high bandwidth "backhaul" for Internet or cellular phone traffic from remote areas back to an Internet backbone. Although the cost per user/point of WiMAX in a remote application will be higher, it is not limited to such applications, and may be an answer to reducing the cost of T1/E1 backhaul as well. Given the limited wired infrastructure in some developing countries, the costs to install a WiMAX station in conjunction with an existing cellular tower or even as a solitary hub are likely to be small in comparison to developing a wired solution. Areas of low population density and flat terrain are particularly suited to WiMAX and its range. For countries that have skipped wired infrastructure as a result of prohibitive costs and unsympathetic geography, WiMAX can enhance wireless infrastructure in an inexpensive, decentralized, deployment-friendly and effective manner.

Technical information

WiMAX is a term coined to describe standard, interoperable implementations of IEEE 802.16 wireless networks, similar to the way the term Wi-Fi is used for interoperable implementations of the IEEE 802.11 Wireless LAN standard. However, WiMAX is very different from Wi-Fi in the way it works.

MAC layer/data link layer

In Wi-Fi the media access controller (MAC) uses contention access — all subscriber stations that wish to pass data through a wireless access point (AP) are competing for the AP's attention on a random interrupt basis. This can cause subscriber stations distant from the AP to be repeatedly interrupted by closer stations, greatly reducing their throughput. This makes services such as Voice over IP (VoIP) or IPTV, which depend on an essentially-constant Quality of Service (QoS) depending on data rate and interruptibility, difficult to maintain for more than a few simultaneous users.

In contrast, the 802.16 MAC uses a scheduling algorithm for which the subscriber station need compete once (for initial entry into the network). After that it is allocated an access slot by the base station. The time slot can enlarge and contract, but remains assigned to the subscriber station, which means that other subscribers cannot use it. In addition to being stable under overload and over-subscription (unlike 802.11), the 802.16 scheduling algorithm can also be more bandwidth efficient. The scheduling algorithm also allows the base station to control QoS parameters by balancing the time-slot assignments among the application needs of the subscriber stations.

Physical layer

The original WiMAX standard (IEEE 802.16) specified WiMAX for the 10 to 66 GHz range. 802.16a, updated in 2004 to 802.16-2004, added specifications for the 2 to 11 GHz range. 802.16-2004 was updated to 802.16e in 2005 and uses scalable orthogonal frequency-division multiple access (SOFDMA) as opposed to the OFDM version with 256 sub-carriers (of which 200 are used) in 802.16d. More advanced versions, including 802.16e, also bring Multiple Antenna Support through Multiple-input multiple-output communications (MIMO) See WiMAX MIMO. This brings potential benefits in terms of coverage, self installation, power consumption, frequency re-use and bandwidth efficiency. 802.16e also adds a capability for full mobility support. The WiMAX certification allows vendors with 802.16d products to sell their equipment as WiMAX certified, thus ensuring a level of interoperability with other certified products, as long as they fit the same profile.

Most commercial interest is in the 802.16d and .16e standards, since the lower frequencies used in these variants suffer less from inherent signal attenuation and therefore give improved range and in-building penetration. Already today, a number of networks throughout the world are in commercial operation using certified WiMAX equipment compliant with the 802.16d standard.

Architecture

The WiMAX Forum WiMAX Architecture

The WiMAX Forum has defined an architecture that defines how a WiMAX network connects with other networks, and a variety of other aspects of operating such a network, including address allocation, authentication, etc. An overview of the architecture is given in the illustration. This defines the following components:

• SS/MS: the Subscriber Station/Mobile Station
• ASN: the Access Service Network
• BS: Base station, belongs to ASN
• ASN-GW: belongs to ASN
• CSN: the Connectivity Service Network
• HA: Home Agent, belongs to CSN
• AAA: AAA Server, belongs to CSN
• NAP: a Network Access Provider
• NSP: a Network Service Provider

plus a number of interconnections (or reference points) between these, labeled R1 to R5 and R8.

It's important to note that the functional architecture can be designed into various hardware configurations rather than fixed configurations. For example, the architecture is flexible to allow various scale and functionality of remote/mobile stations and collaborative aggregations of femto, pico, and mini RS/MS.

Comparison with Wi-Fi

Possibly due to the fact both WiMAX and Wi-Fi begin with the same two letters, are based upon IEEE standards beginning with "802.", and both have a connection to wireless connectivity and the Internet, comparisons and confusion between the two are frequent. Despite this, the two standards are aimed at different applications.

• WiMAX is a long-range system, covering many kilometers that typically uses licensed spectrum (although it is also possible to use unlicensed spectrum) to deliver a point-to-point connection to the Internet from an ISP to an end user. Different 802.16 standards provide different types of access, from mobile (analogous to access via a cellphone) to fixed (an alternative to wired access, where the end user's wireless termination point is fixed in location.)
• Wi-Fi is a shorter range system, typically hundreds of meters, that uses unlicensed spectrum to provide access to a network, typically covering only the network operator's own property. Typically Wi-Fi is used by an end user to access their own network, which may or may not be connected to the Internet. If WiMAX provides services analogous to a cellphone, Wi-Fi is more analogous to a cordless phone.
• WiMAX and Wi-Fi have quite different Quality of Service (QoS) mechanisms. WiMAX uses a mechanism based on setting up connections between the Base Station and the user device. Each connection is based on specific scheduling algorithms, which means that QoS parameters can be guaranteed for each flow. WiFi has introduced a QoS mechanism similar to fixed Ethernet, where packets can receive different priorities based on their tags. This means that QoS is relative between packets/flows, as opposed to guaranteed.
• WiMAX is highly scalable from what are called "femto"-scale remote stations to multi-sector 'maxi' scale base that handle complex tasks of management and mobile handoff functions and include MIMO-AAS smart antenna subsystems.

Due to the ease and low cost with which Wi-Fi can be deployed, it is sometimes used to provide Internet access to third parties within a single room or building available to the provider, often informally, and sometimes as part of a business relationship. For example, many coffee shops, hotels, and transportation hubs contain Wi-Fi access points providing access to the Internet for customers.

Spectrum allocation issues

The 802.16 specification applies across a wide swath of the RF spectrum, and WiMAX could function on any frequency below 66GHz"IEEE Standard for Local and metropolitan area networks Part 16: Air Interface for Fixed and Mobile Broadband Wireless Access Systems Amendment 2: Physical and Medium Access Control Layers for Combined Fixed and Mobile Operation in Licensed Bands and Corrigendum 1," IEEE Std 802.16e-2005 and IEEE Std 802.16-2004/Cor 1-2005 (Amendment and Corrigendum to IEEE Std 802.16-2004) (PDF), 2006, p. 3, retrieved Oct 25, 2007, (higher frequencies would decrease the range of a Base Station to a few hundred meters in an urban environment).

There is no uniform global licensed spectrum for WiMAX, although the WiMAX Forum has published three licensed spectrum profiles: 2.3GHz, 2.5GHz and 3.5GHz, in an effort to decrease cost: economies of scale dictate that the more WiMAX embedded devices (such as mobile phones and WiMAX-embedded laptops) are produced, the lower the unit cost. (The two highest cost components of producing a mobile phone are the silicon and the extra radio needed for each band.) Similar economy of scale benefits apply to the production of Base Stations.

In the unlicensed band, 5.x GHz is the approved profile. Telecom companies are unlikely to use this spectrum widely other than for backhaul, as they do not own and control the spectrum.

In the USA, the biggest segment available is around 2.5 GHz, and is already assigned, primarily to Sprint Nextel and Clearwire. Elsewhere in the world, the most-likely bands used will be the Forum approved ones, with 2.3 GHz probably being most important in Asia. Some countries in Asia like India, Vietnam and Indonesia will use a mix of 3.3 GHz and other frequencies.

Analogue TV bands (700MHz) may become available for WiMAX use, but await the complete rollout of digital TV, and there will be other uses suggested for that spectrum. In the USA the FCC auction for this spectrum is scheduled for January 2008 [2]. EU commissioner Viviane Reding has suggested re-allocation of 500-800 MHz spectrum for wireless communication, including WiMAX [3].

WiMAX profiles define channel size, TDD/FDD and other necessary attributes in order to have inter-operating products. The current fixed profiles are defined for both TDD and FDD profiles. At this point, all of the mobile profiles are TDD only. The fixed profiles have channel sizes of 3.5 MHz, 5 MHz, 7 MHz and 10 MHz. The mobile profiles are 5 MHz, 8.75 MHz and 10 MHz. (Note: the 802.16 standard allows a far wider variety of channels, but only the above subsets are supported as WiMAX profiles).

Since October 2007, the Radiocommunication Sector of the International Telecommunication Union (ITU-R) has decided to include WiMAX technology in the IMT-2000 set of standards. This enables spectrum owners (specifically in the 2.5-2.69GHz band at this stage) to use Mobile WiMAX equipment in any country that recognizes the IMT-2000.

Spectral Efficiency

One of the significant advantages of advanced wireless systems such as WiMAX is spectral efficiency. For example, 802.16-2004 (fixed) has a spectral efficiency of 3.7 bit/s/Hertz, and other 3.5-4G wireless systems offer spectral efficiencies that are similar to within a few tenths of a percent. The notable advantage of WiMAX comes from combining SOFDMA with smart antenna technologies. This multiplies the effective spectral efficiency through multiple reuse and smart network deployment topologies. The direct use of frequency domain organization simplifies designs using MIMO-AAS compared to CDMA/WCDMA methods, resulting in more-effective systems.

Limitations

A commonly-held misconception is that WiMAX will deliver 70 Mbit/s over 50 kilometers. Both of these qualities are true individually, given ideal circumstances, but they are not simultaneously true.

The nature of wireless communications dictates that the antenna design will have a substantial impact on what is achievable. Typically, Fixed WiMAX networks have a higher-gain directional antenna installed externally at the customer's premises which results in greatly increased range and throughput. Mobile WiMAX networks comprise mostly of indoor customer premise equipment (CPEs) such as desktop modems, laptops with integrated Mobile WiMAX or other Mobile WiMAX devices. Mobile WiMAX devices typically have an antenna design which is of lower-gain by nature due to their inherent omni-directional (and portable) design. In practice this means that in a line-of-sight environment with a portable Mobile WiMAX CPE, symmetrical speeds of 10 Mbit/s at 10 km could be delivered, but in urban environments it is more likely that these devices will not have line-of-sight and therefore users may only receive 10 Mbit/s over 2 km. Higher-gain directional antennas can be used with a Mobile WiMAX network with range and throughput benefits but the obvious loss of practical mobility.

Like most wireless systems, available bandwidth is shared between users in a given radio sector, so performance could deteriorate in the case of many active users in a single sector. In practice, many users will have a range of 2-, 4-, 6-, 8-, 10- or 12 Mbit/s services and additional radio cards will be added to the base station to increase the capacity as required.

Because of this, various granular and distributed network architectures are being incorporated into WiMAX through independent development and within the 802.16j mobile multi-hop relay (MMR) task group. This includes wireless mesh, grids, network remote station repeaters which can extend networks and connect to backhaul.

Silicon implementations

A critical requirement for the success of a new technology is the availability of low-cost chipsets and silicon implementations.

Intel is a leader in promoting WiMAX, and has developed its own chipset. However, it is notable that most of the major semiconductor companies have to date been more cautious of involvement and most of the solutions come from specialist smaller or start-up suppliers. For the client-side these include GCT, Altair, Beceem, GCI, Runcom, Motorola with TI, NextWave, Sequans and a number of others. Both Sequans and Wavesat manufacture solutions for both clients and network while TI, DesignArt, and picoChip are focused on WiMAX chipsets for basestations.

Standards

The current WiMAX incarnation, Mobile WiMAX, is based upon IEEE Std 802.16e-2005, approved in December 2005. It is an amendment of IEEE Std 802.16-2004 and so the actual standard is 802.16-2004 as amended by 802.16e-2005 - the specifications need to be read together to understand them.

IEEE Std 802.16-2004 addresses only fixed systems. It replaced IEEE Standards 802.16-2001, 802.16c-2002, and 802.16a-2003.

IEEE 802.16e-2005

IEEE 802.16e-2005 improves upon IEEE 802.16-2004 by:

• Adding support for mobility (soft and hard handover between base stations). This is seen as one of the most important aspects of 802.16e-2005, and is the very basis of 'Mobile WiMAX'.
• Scaling of the Fast Fourier Transform (FFT) to the channel bandwidth in order to keep the carrier spacing constant across different channel bandwidths (1.25-20 MHz). Constant carrier spacing results in a higher spectrum efficiency in wide channels, and a cost reduction in narrow channels. Also known as Scalable OFDMA (SOFDMA).
• Improving NLOS coverage by utilizing advanced antenna diversity schemes, and hybrid-Automatic Retransmission Request (hARQ)
• Improving capacity and coverage by introducing Adaptive Antenna Systems (AAS) and Multiple Input Multiple Output (MIMO) technology
• Increasing system gain by use of denser sub-channelization, thereby improving indoor penetration
• Introducing high-performance coding techniques such as Turbo Coding and Low-Density Parity Check (LDPC), enhancing security and NLOS performance
• Introducing downlink sub-channelization, allowing administrators to trade coverage for capacity or vice versa
• Enhanced Fast Fourier Transform algorithm can tolerate larger delay spreads, increasing resistance to multipath interference
• Adding an extra QoS class (enhanced real-time Polling Service) more appropriate for VoIP applications.

802.16d vendors point out that fixed WiMAX offers the benefit of available commercial products and implementations optimized for fixed access. It is a popular standard among alternative service providers and operators in developing areas due to its low cost of deployment and advanced performance in a fixed environment. Fixed WiMAX is also seen as a potential standard for backhaul of wireless base stations such as cellular, WiFi or even Mobile WiMAX.

SOFDMA (used in 802.16e-2005) and OFDM256 (802.16d) are not compatible so most equipment will have to be replaced if an operator wants or needs to move to the later standard. However, some manufacturers are planning to provide a migration path for older equipment to SOFDMA compatibility which would ease the transition for those networks which have already made the OFDM256 investment. Intel provides a dual-mode 802.16-2004 802.16-2005 chipset for subscriber units. This affects a relatively small number users and operators.

Associations

WiMAX Forum

WiMAX Forum logo

WiMAX Forum logo

The WiMAX Forum is the organization dedicated to certifying the interoperability of WiMAX products. Those that pass conformance and interoperability testing achieve the "WiMAX Forum Certified" designation and can display this mark on their products and marketing materials. Some vendors claim that their equipment is "WiMAX-ready", "WiMAX-compliant", or "pre-WiMAX", if they are not officially WiMAX Forum Certified.

WiMAX Spectrum Owners Alliance - WiSOA

WiSOA is the first global organization composed exclusively of owners of WiMAX spectrum with plans to deploy WiMAX technology in those bands. WiSOA is focussed on the regulation, commercialisation, and deployment of WiMAX spectrum in the 2.3–2.5 GHz and the 3.4–3.5 GHz ranges. WiSOA are dedicated to educating and informing its members, industry representatives and government regulators of the importance of WiMAX spectrum, its use, and the potential for WiMAX to revolutionise broadband.

Competing technologies

Within the marketplace, WiMAX's main competition comes from existing widely deployed wireless systems such as UMTS and CDMA2000, as well as a number of Internet oriented systems such as HIPERMAN and WiBro.

3G and 4G cellular phone Systems

Both of the two major 3G systems, CDMA2000 and UMTS, compete with WiMAX. Both aim to offer DSL-class Internet access in addition to phone service. UMTS has also been enhanced to compete directly with WiMAX in the form of UMTS-TDD, which can use WiMAX oriented spectrum and provides a more consistent, if lower bandwidth at peak, user experience than WiMAX.

3G cellular phone systems usually benefit from already having entrenched infrastructure, being upgraded from earlier systems. Users can usually fall back to older systems when they move out of range of upgraded equipment, often relatively seamlessly.

The major cellular standards are being evolved to so-called 4G, high bandwidth, low latency, all-IP networks with voice services built on top. With GSM/UMTS, the move to 4G is the 3GPP Long Term Evolution effort. For AMPS/TIA derived standards such as CDMA2000, a replacement called Ultra Mobile Broadband is under development. In both cases, existing air interfaces are being discarded, in favour of OFDMA for the downlink and a variety of OFDM based solutions for the uplink, much akin to WiMAX.

In some areas of the world the wide availability of UMTS and a general desire for standardization has meant spectrum has not been allocated for WiMAX: in July 2005, the EU-wide frequency allocation for WiMAX was blocked.

Mobile Broadband Wireless Access

Mobile Broadband Wireless Access (MBWA) is a technology being developed by IEEE 802.20 and is aimed at wireless mobile broadband for operations from 120 to 350 km/h. The 802.20 standard committee was first to define many of the methods which where later funneled into Mobile WiMAX, including high speed dynamic modulation and similar scalable OFDMA capabilities. It apparently retains fast hand-off, Forward Error Correction (FEC) and cell edge enhancements.

The Working Group was temporarily suspended in mid 2006 by the IEEE-SA Standards Board since it had been the subject of a number of appeals, and a preliminary investigation of one of these "revealed a lack of transparency, possible 'dominance,' and other irregularities in the Working Group".

In September 2006 the IEEE-SA Standards Board approved a plan to enable the working group to continue under new conditions, and the standard is now expected to be finalized by Q2 2008.

Internet-oriented systems

Early WirelessMAN standards, the European standard HIPERMAN and Korean standard WiBro have been harmonized as part of WiMAX and are no longer seen as competition but as complementary. All networks now being deployed in South Korea, the home of the Wibro standard, are now WiMAX.

As a short-range mobile Internet solution, such as in cafes and at transportation hubs like airports, the popular WiFi 802.11b/g system is widely deployed, and provides enough coverage for some users to feel subscription to a WiMAX service is unnecessary.

Comparison

Main article: Comparison of wireless data standards

The following table should be treated with caution as it only shows peak rates which are potentially very misleading. In addition the comparisons listed are not normalized by physical channel size (i.e. spectrum used to achieve the listed peak rates); this obfuscates spectral efficiency and net through-put capabilities of the different wireless technologies listed below.

Comparison of mobile Internet access methods

Common name	Family	Primary use	Radio tech	Downstream (Mbit/s)	Upstream (Mbit/s)	Notes
HSPA+	3GPP	Mobile Internet	CDMA/TDMA/FDD MIMO	21 42 84 672	5.8 11.5 22 168	HSPA+ is widely deployed. Revision 11 of the 3GPP states that HSPA+ is expected to have a throughput capacity of 672 Mbit/s.
LTE	3GPP	Mobile Internet	OFDMA/TDMA/MIMO/SC-FDMA/for LTE-FDD/for LTE-TDD	100 Cat3 150 Cat4 300 Cat5 25065 Cat17 1658 Cat19 (in 20 MHz FDD)	50 Cat3/4 75 Cat5 2119 Cat17 13563 Cat19 (in 20 MHz FDD)	LTE-Advanced Pro offers rates in excess of 3 Gbit/s to mobile users.
WiMax rel 1	802.16	WirelessMAN	MIMO-SOFDMA	37 (10 MHz TDD)	17 (10 MHz TDD)	With 2x2 MIMO.
WiMax rel 1.5	802.16-2009	WirelessMAN	MIMO-SOFDMA	83 (20 MHz TDD) 141 (2x20 MHz FDD)	46 (20 MHz TDD) 138 (2x20 MHz FDD)	With 2x2 MIMO.Enhanced with 20 MHz channels in 802.16-2009
WiMAX rel 2.0	802.16m	WirelessMAN	MIMO-SOFDMA	2x2 MIMO 110 (20 MHz TDD) 183 (2x20 MHz FDD) 4x4 MIMO 219 (20 MHz TDD) 365 (2x20 MHz FDD)	2x2 MIMO 70 (20 MHz TDD) 188 (2x20 MHz FDD) 4x4 MIMO 140 (20 MHz TDD) 376 (2x20 MHz FDD)	Also, low mobility users can aggregate multiple channels to get a download throughput of up to 1 Gbit/s
Flash-OFDM	Flash-OFDM	Mobile Internet mobility up to 200 mph (350 km/h)	Flash-OFDM	5.3 10.6 15.9	1.8 3.6 5.4	Mobile range 30 km (18 miles) Extended range 55 km (34 miles)
HIPERMAN	HIPERMAN	Mobile Internet	OFDM	56.9
Wi-Fi	802.11 (11ax)	Wireless LAN	OFDM/OFDMA/CSMA/MIMO/MU-MIMO/Half duplex	9600 Wi-Fi 6		Antenna, RF front end enhancements and minor protocol timer tweaks have helped deploy long range P2P networks compromising on radial coverage, throughput and/or spectra efficiency (310 km & 382 km)
iBurst	802.20	Mobile Internet	HC-SDMA/TDD/MIMO	95	36	Cell Radius: 3–12 km Speed: 250 km/h Spectral Efficiency: 13 bits/s/Hz/cell Spectrum Reuse Factor: "1"
EDGE Evolution	GSM	Mobile Internet	TDMA/FDD	1.6	0.5	3GPP Release 7
UMTS W-CDMA HSPA (HSDPA+HSUPA)	3GPP	Mobile Internet	CDMA/FDD CDMA/FDD/MIMO	0.384 14.4	0.384 5.76	HSDPA is widely deployed. Typical downlink rates today 2 Mbit/s, ~200 kbit/s uplink; HSPA+ downlink up to 56 Mbit/s.
UMTS-TDD	3GPP	Mobile Internet	CDMA/TDD	16		Reported speeds according to IPWireless using 16QAM modulation similar to HSDPA+HSUPA
EV-DO Rel. 0 EV-DO Rev.A EV-DO Rev.B	3GPP2	Mobile Internet	CDMA/FDD	2.45 3.1 4.9xN	0.15 1.8 1.8xN	Rev B note: N is the number of 1.25 MHz carriers used. EV-DO is not designed for voice, and requires a fallback to 1xRTT when a voice call is placed or received.

Notes: All speeds are theoretical maximums and will vary by a number of factors, including the use of external antennas, distance from the tower and the ground speed (e.g. communications on a train may be poorer than when standing still). Usually the bandwidth is shared between several terminals. The performance of each technology is determined by a number of constraints, including the spectral efficiency of the technology, the cell sizes used, and the amount of spectrum available.

For more comparison tables, see bit rate progress trends, comparison of mobile phone standards, spectral efficiency comparison table and OFDM system comparison table.

Future development

Mobile WiMAX based upon 802.16e-2005 has been accepted as IP-OFDMA for inclusion as the sixth wireless link system under IMT-2000. This can hasten acceptance by regulatory authorities and operators for use in cellular spectrum. WiMAX II, 802.16m will be proposed for IMT-Advanced 4G.

The goal for the long term evolution of both WiMAX and LTE is to achieve 100 Mbit/s mobile and 1 Gbit/s fixed-nomadic bandwidth as set by ITU for 4G NGMN (Next Generation Mobile Network) systems through the adaptive use of MIMO-AAS and smart, granular network topologies. 3GPP LTE and WiMAX-m are concentrating much effort on MIMO-AAS, mobile multi-hop relay networking and related developments needed to deliver 10X and higher Co-Channel reuse multiples.

Since the evolution of core air-link technologies has approached the practical limits imposed by Shannon's Theorem, the evolution of wireless has embarked on pursuit of the 3X to 10X+ greater bandwidth and network efficiency gains that are expected by advances in the spatial and smart wireless broadband networking technologies. What will clearly define 4G more than either WCDMA or OFDMA wireless link methods will be wireless networks that more effectively adapt to and take advantage of available spectrum.

Current deployments

Main article: List of Deployed WiMAX networks

(Country by Country List)

The WiMAX Forum now lists over 350 WiMAX trials and deployments. Current and planned deployments and the bands in which they operate and the standards they use are listed in the above article.

See also

• ITU Radiocommunication Assembly approves new developments for its 3G standards
• Wireless local loop also know as Fixed Wireless Access (FWA)
• Municipal broadband
• WiBro
• Switched mesh

Literature

• The Access Service Network in WiMAX: The Role of ASN-GW by Mustafa Ergen, October 2007.

Fundamentals of WiMAX: Understanding Broadband Wireless Networking -- The Definitive Guide to WiMAX Technology, written by three leading wireless experts Jeffrey G. Andrews, Arunabha Ghosh, Rias Muhamed (Prentice Hall Professional, February 2007)

• L. Nuaymi: WiMAX, Technology for Broadband Wireless Access, Wiley, January 2007, ISBN 9780470028087
• M. Sauter: Communication Systems for the Mobile Information Society, John Wiley, September 2006, ISBN 0-470-02676-6
• WiMAX Forum Whitepapers: http://www.wimaxforum.org/technology/downloads/
• WiMAX Forum Technical Documents and Specifications: http://www.wimaxforum.org/technology/documents/
• A. Bahai, B. Saltzberg and M. Ergen, [Multi-Carrier Digital Communications: Theory and Practice of OFDM]http://ofdm.eecs.berkeley.edu, Springer, 2004,
• WiMAX Day: An on-line journal of WiMAX news and information

External links

• WiMAX Forum
• IEEE 802.16 — The IEEE 802.16 Working Group on Broadband Wireless Access Standards